15E test report pt1

FCC ID: N6C-SX10WAG

Test Report

Download: PDF
FCCID_909638

Test report No. : 28CEO213—HO—01—A Underwriters Page : 1 of 94 Laboratories UL Japan, Inc. Issued date : February 25, 2008 FCC ID : N6C—SX10WAG EMI TEST REPORT Test Report No. : 28CE0213-HO-01-A Applicant silex technology, Inc. Type of Equipment MiniPCI Wireless LAN board Model No. SX—10WAG FCC ID N6C—SX10WAG Test regulation FCC Part 15 Subpart E: 2008 Section 15.407 Test Result Complied 1. This test report shall not be reproduced in full or partial, without the written approval of UL Japan, Inc. The results in this report apply only to the sample tested. y p 4 p This sample tested is in compliance with above regulation. The test results in this report are traceable to the national or international standards. This test report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. Date of test: January 10 to February 20, 2008 Tested by: bt. , Oartughe Kenichi Adachi EMC Services Approved by : P Amo»r w Mironobu Shijindji Assistant Manager of EMC Services nving This laboratory is accredited by the NVLAP LAB CODE ® 200572—0, U.S.A. The tests reported herein have been performed in accordance with its terms of accreditation. *As for the range of Accreditation in NVLAP, you may refer to the WEB address, http://uljapan.co.jp/eme/nvlap.htm NVLAP LAB CODE: 200572—0 UL Japan, Inc. Head Office EMC Lab. MFO6Ob (09.01.08) 4383—326 Asama—cho, Ise—shi, Mic—ken 516—0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124

Test report No. : 28CE0213-HO-01-A Page : 2 of 94 Issued date : February 25, 2008 FCC ID : N6C-SX10WAG CONTENTS PAGE SECTION 1: Customer information ........................................................................................3 SECTION 2: Equipment under test (E.U.T.) ..........................................................................3 SECTION 3: Test specification, procedures & results ...........................................................5 SECTION 4: Operation of E.U.T. during testing ...................................................................9 SECTION 5: Conducted Emission ..........................................................................................13 SECTION 6: Spurious Emission and Band Edge Compliance............................................14 SECTION 7: Maximum Peak Output Power........................................................................14 APPENDIX 1: Photographs of test setup...............................................................................15 Conducted Emission .................................................................................................................... 15 Spurious Emission (Radiated)..................................................................................................... 18 Worst Case Position (Horizontal: Z-axis/Vertical: Z-axis) ...................................................... 27 APPENDIX 2: Data of EMI test ..............................................................................................28 Maximum Peak Output Power ................................................................................................... 28 Conducted Emission .................................................................................................................... 32 Radiated Spurious Emission (below 1GHz ).............................................................................. 45 Radiated Spurious Emission (above 1GHz:Inside of the restricted band) ............................. 57 Radiated Spurious Emission (above 1GHz:Outside of the restricted band) .......................... 72 Radiated emission Band Edge compliance ................................................................................ 90 APPENDIX 3:Test instruments ...............................................................................................93 UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124

Test report No. : 28CE0213-HO-01-A Page : 3 of 94 Issued date : February 25, 2008 FCC ID : N6C-SX10WAG SECTION 1: Customer information Company Name : silex technology, Inc. Address : 2-3-1 Hikaridai, Seika-cho, Kyoto 619-0237, Japan Telephone Number : +81-774-98-3878 Facsimile Number : +81-774-98-3758 Contact Person : Toshiro Kometani SECTION 2: Equipment under test (E.U.T.) 2.1 Identification of E.U.T. Type of Equipment : MiniPCI Wireless LAN Board Model No. : SX-10WAG (MiniPCI Wireless LAN Board), HG5808U (Antenna), HG5817D (Antenna), SR49120WDA (Antenna) Serial No. : 32 (SX-10WAG), 1 (HG5808U), 1 (HG5817D), 1 (SR49120WDA) Rating : DC3.3V Country of Manufacture : Japan Receipt Date of Sample : January 15, 2008 Condition of EUT : Engineering prototype (Not for Sale: These samples are equivalent to mass-produced items.) Modification of EUT : No modification by the test lab. 2.2 Product Description Model: SX-10WAG is the MiniPCI Wireless LAN Board. Equipment Type : Transceiver Clock frequency : 40MHz Method of Frequency Generation : Crystal Operating voltage (inner) : DC3.3V +/-0.3V IEEE802.11b IEEE802.11g IEEE802.11a Frequency of operation 2412-2462MHz 2412-2462MHz 5180-5320MHz 5745-5825MHz Type of modulation DSSS OFDM OFDM (CCK, DQPSK, DBPSK) (64QAM, 16QAM, QPSK, (64QAM, 16QAM, QPSK, BPSK) BPSK) Bandwidth &Channel 22MHz & 5MHz 22MHz & 5MHz 22MHz & 5MHz number ITU Code G1D D1D D1D Antenna connector U.FL U.FL U.FL *1) Module of the EUT (MiniPCI Wireless LAN Board) is identical to the one in the following test reports: Refer to 26GE0351-HO-B (FCC15E), 26GE0351-HO-D-1(RSS-210(5GHz)), UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124

Test report No. : 28CE0213-HO-01-A Page : 4 of 94 Issued date : February 25, 2008 FCC ID : N6C-SX10WAG Antenna Antenna antenna gain antenna connector HG5808U 8dBi max N Female HG5817D 17dBi max N Female SR49120WDA 11dBi max N Female Antenna cable Antenna cable Length (m) antenna connector antenna connector for module side for antenna side Coxial cable 0.08 U.FL Reverse SMA CA-RSPNMA004 1.2 (4ft) Reverse SMA N male CA-RSPNMA010 3.0 (10ft) Reverse SMA N male CA-NMNFA004 1.2 (4ft) N Female N male CA4NMRSF020 6.0 (20ft) Reverse SMA N male UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124

Test report No. : 28CE0213-HO-01-A Page : 5 of 94 Issued date : February 25, 2008 FCC ID : N6C-SX10WAG SECTION 3: Test specification, procedures & results 3.1 Test Specification Test Specification : FCC Part15 Subpart E: 2008, final revised on January 30, 2008 Title : FCC 47CFR Part15 Radio Frequency Device Subpart E Unlicensed National Information Infrastructure Devices Section 15.407 General technical requirements *The revision on January 30, 2008 does not influence the test specification applied to the EUT. FCC 15.31 (e) This EUT provides stable voltage(DC3.3V) constantly to RF Module regardless of input voltage. Therefore, this EUT complies with the requirement. UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124

Test report No. : 28CE0213-HO-01-A Page : 6 of 94 Issued date : February 25, 2008 FCC ID : N6C-SX10WAG 3.2 Procedures and results No. Item Test Procedure Specification Remarks Deviation Worst margin Results FCC : 26dB Emission FCC :ANSI C63.4:2003 1 15.407(a)(3) Conducted N/A N/A *1) Bandwidth IC: - IC: RSS-210 A9.2 (3) Maximum Peak FCC : FCC :ANSI C63.4:2003 2 Output Power 15.407(a)(3) Conducted N/A Complied IC: - IC: RSS-210 A.9.2 (3) See data FCC : Peak Power Spectral FCC ANSI C63.4:2003 3 15.407(a)(3) Conducted N/A N/A *1) Density IC: - IC: RSS-210 A.9.2 (3) FCC : FCC :ANSI C63.4:2003 4 Peak Excursion Ratio 15.407(a)(6) Conducted N/A N/A *1) IC: - IC: - FCC : 15.407(b)(4) [Tx] FCC: ANSI C63.4:2003 (5)(6)(7), 15.205and15.209 0.2dB Conducted 5715MHz, Vertical 5 Spurious Emission N/A Complied IC: - IC: RSS-210 A.9.3 (4) Radiated [Rx] 2.4dB 500MHz, Vertical FCC :ANSI C63.4:2003 FCC: 15.407(b)(6)/15.207 [QP] 15.5dB, L, IC: RSS-Gen 7.2.2 IC: RSS-Gen 7.2.2 0.20433MHz, 6 Conducted Emission - N/A Complied [AV] 7.5dB, L, 0.20433MHz, FCC : 0.2dB Band Edge FCC :ANSI C63.4:2003 7 15.407(b)(4)(7)/15.205 Radiated N/A 5715MHz, Complied Compliance IC: - IC: RSS-210 A.9.3 (4) Vertical 99％ Occupied 8 IC RSS-Gen 4.6.1 RSS-Gen 4.6.1 Conducted N/A N/A N/A *1) Band Width Note: UL Japan, Inc.’s EMI Work Procedures No.QPM05 and QPM15. *1) This test report is for Permissive Class II change application in order to add antenna and antenna cables to the approved model. Since only antenna and antenna cable was added to the model, the tests related to the module itself were excluded. *These tests were also referred to FCC Public Notice DA 02-2138A1 "Measurement Procedure Updated for Peak Transmit Power in the Unlicensed National Information Infrastructure (U-NII) Bands ". *These tests were performed without any deviations from test procedure except for additions or exclusions. 3.3 Additions or deviations to standards No addition nor deviation exclusion has been made from standards. UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124

Test report No. : 28CE0213-HO-01-A Page : 7 of 94 Issued date : February 25, 2008 FCC ID : N6C-SX10WAG 3.4 Uncertainty The following uncertainties have been calculated to provide a confidence level of 95% using a coverage factor k=2. Conducted Radiated emission Radiated emission Radiated emission (10m*) (3m*) emission Test room (3m*) 150kHz- 9kHz- 30MHz- 300MHz- 9kHz- 30MHz- 300MHz- 1GHz- 18GHz- 30MHz 30MHz 300MHz 1GHz 30MHz 300MHz 1GHz 18GHz 40GHz No.1 3.7dB 3.1dB 4.7dB 4.4dB 3.2dB 3.7dB 4.4dB 5.9dB 6.1dB semi-anechoic Chamber (±) No.2 3.7dB - - - 3.2dB 4.3dB 3.9dB 5.9dB 6.1dB semi-anechoic chamber (±) No.3 3.7dB - - - 3.2dB 4.2dB 4.4dB 5.9dB 6.1dB semi-anechoic chamber (±) No.4 3.7dB - - - 3.2dB 4.2dB 4.4dB 5.9dB 6.1dB semi-anechoic chamber (±) *10m/3m = Measurement distance Conducted emission test The data listed in this test report has enough margin, more than the site margin. Radiated emission test(3m) The data listed in this report meets the limits unless the uncertainty is taken into consideration. UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124

Test report No. : 28CE0213-HO-01-A Page : 8 of 94 Issued date : February 25, 2008 FCC ID : N6C-SX10WAG 3.5 Test Location UL Japan, Inc. Head Office EMC Lab. *NVLAP Lab. code: 200572-0 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124 FCC IC Registration Width x Depth x Size of Other Registration Number Height (m) reference ground plane (m) / rooms Number horizontal conducting plane No.1 semi-anechoic 313583 IC4247 19.2 x 11.2 x 7.7m 7.0 x 6.0m No.1 Power chamber source room No.2 semi-anechoic 655103 IC4247-2 7.5 x 5.8 x 5.2m 4.0 x 4.0m - chamber No.3 semi-anechoic 148738 IC4247-3 12.0 x 8.5 x 5.9m 6.8 x 5.75m No.3 chamber Preparation room No.3 shielded room - - 4.0 x 6.0 x 2.7m N/A - No.4 semi-anechoic 134570 IC4247-4 12.0 x 8.5 x 5.9m 6.8 x 5.75m No.4 chamber Preparation room No.4 shielded room - - 4.0 x 6.0 x 2.7m N/A - No.5 semi-anechoic - - - 6.0 x 6.0 x 3.9m 6.0 x 6.0m chamber No.6 shielded - - 4.0 x 4.5 x 2.7m 4.75 x 5.4 m - room No.6 measurement - - 4.75 x 5.4 x 3.0m 4.75 x 4.15 m - room No.7 shielded room - - 4.7 x 7.5 x 2.7m 4.7 x 7.5m - No.8 measurement - - 3.1 x 5.0 x 2.7m N/A - room No.9 measurement - - 8.0 x 4.5 x 2.8m 2.0 x 2.0m - room No.10 measurement - - 2.6 x 2.8 x 2.5m 2.4 x 2.4m - room No.11 measurement - - 3.1 x 3.4 x 3.0m 2.4 x 3.4m - room * Size of vertical conducting plane (for Conducted Emission test) : 2.0 x 2.0m for No.1, No.2, No.3, and No.4 semi-anechoic chambers and No.3 and No.4 shielded rooms. 3.6 Test set up, Test instruments and Data of EMI Refer to APPENDIX 1 to 3. UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124

Test report No. : 28CE0213-HO-01-A Page : 9 of 94 Issued date : February 25, 2008 FCC ID : N6C-SX10WAG SECTION 4: Operation of E.U.T. during testing 4.1 Operating Modes The EUT was operating in a manner similar to typical use during the tests. Mode : Transmitting (Tx) mode (OFDM, 54Mbps, Payload: PN9, ) * See Remarks. Channel 149: 5745MHz Channel 153: 5765MHz Channel 161: 5805MHz Receiving (Rx) mode Channel 153: 5765MHz Conditions : 1) IEEE802.11a:6, 9, 12, 18, 24, 36, 48, 54 Mbps 2) Antenna Port A and B (same type) <Remarks> *We pre-confirmed the above conditions on EUT and performed the final test with the following conditions; IEEE802.11a Radiated emission 1) Rate: 54Mbps test 2) Antenna Port A Radiated emission test : As for Rate,54Mbps (Maximum transmission rate of 11a) had worst margins. The result of Antenna Port A had worst margin. * The followings are the combinations of EUT’s antenna and antenna cable. This report is for Permissive Class II change application in order to add the following antenna and antenna cables. Antenna Antenna antenna gain antenna connector HG5808U 8dBi max N Female HG5817D 17dBi max N Female SR49120WDA 11dBi max N Female Antenna cable Antenna cable Length (m) antenna connector antenna connector for module side for antenna side Coxial cable 0.08 U.FL Reverse SMA CA-RSPNMA004 1.2 (4ft) Reverse SMA N male CA-RSPNMA010 3.0 (10ft) Reverse SMA N male CA-NMNFA004 1.2 (4ft) N Female N male CA4NMRSF020 6.0 (20ft) Reverse SMA N male UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124

Test report No. : 28CE0213-HO-01-A Page : 10 of 94 Issued date : February 25, 2008 FCC ID : N6C-SX10WAG Combination Module Antenna cable 1 Antenna cable 2 Antenna cable 3 Antenna CA-RSPNMA004 CA-RSPNMA010 CA-NMNFA004 HG5808U CA4NMRSF020 CA-RSPNMA004 SX-10WAG Coaxial cable CA-RSPNMA010 CA-NMNFA004 HG5817D CA4NMRSF020 CA-RSPNMA004 CA-RSPNMA010 CA-NMNFA004 SR49120WDA CA4NMRSF020 < Antenna Cable Combination> The test was performed with all the antenna cable combinations only for 10GHz to 18GHz. For other bands, worst combination with only one antenna was performed. (1) HG5808U: Worst antenna cable: CA-RSPNMA010 + CA-NMNFA004 + Coaxial Cable (2) HG5817D: Worst antenna cable: CA-RSPNMA010 + CA-NMNFA004 + Coaxial Cable (3) SR49120WDA: Worst antenna cable: CA-RSPNMA004 + Coaxial Cable 4.2 Configuration and peripherals <Antenna cable CA-RSPNMA004> [ Radiated emission above 1GHz ] [ Radiated emission below 1GHz and Conducted emission] 0.5cm 0.5cm F J K E B, A B, A C, C, D D 6 5 6 1 5 1 7 8 11 H Connecter G Connecter L 12 9 50 ohm I 50 ohm Terminater : Ferrite Core Terminater : Standard Ferrite Core 10 * Cabling and setup were taken into consideration and test data was taken under worse case conditions. UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124

Test report No. : 28CE0213-HO-01-A Page : 11 of 94 Issued date : February 25, 2008 FCC ID : N6C-SX10WAG <Antenna cable CA-RSPNMA010 + CA-NMNFA004 > [ Radiated emission above 1GHz ] [ Radiated emission below 1GHz and Conducted emission ] 0.5cm 0.5cm E F J K B, A B, A C, C, D D 2 6 2 5 6 3 5 7 8 3 11 H Connecter G Connecter L 12 9 50 ohm I 50 ohm Terminater Terminater : Ferrite Core 10 : Standard Ferrite Core * Cabling and setup were taken into consideration and test data was taken under worse case conditions. <Antenna cable CA4NMRSF020> [ Radiated emission above 1GHz ] [ Radiated emission below 1GHz and Conducted emission ] 0.5cm 0.5cm E F J K B, A B, A C, C, D D 6 5 6 4 5 4 7 8 11 H Connecter G Connecter L 12 9 50 ohm I 50 ohm Terminater : Ferrite Core Terminater : Standard Ferrite Core 10 * Cabling and setup were taken into consideration and test data was taken under worse case conditions. UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124

Test report No. : 28CE0213-HO-01-A Page : 12 of 94 Issued date : February 25, 2008 FCC ID : N6C-SX10WAG Description of EUT and Support equipment No. Item Model number Serial number Manufacturer Remarks MiniPCI Wireless SX-10WAG 32 silex technology, Inc. EUT A LAN board B Antenna HG5808U 1 silex technology, Inc. EUT C Antenna HG5817D 1 silex technology, Inc. EUT D Antenna SR49120WDA 1 silex technology, Inc. EUT MiniPCI to PCI - - silex technology, Inc. - E convert adapter Jigu CardBus-PCMCIA ECH(PCI)SF-H2B 6LRBH02000133 CONTEC - F convert adapter CardBus-LAN BUS-PC(CB)SF 7BRBG290000207 CONTEC - G adapter H Personal Computer CF-R3EW1AXS 4KKSA36622 Panasonic - I AC adapter for PC CF-AA1625A M2 04727084B Panasonic - MiniPCI to PCI - - silex technology, Inc. - J convert adapter Jigu K Personal Computer PP341N-30S430 30016021 TOSHIBA - L AC adapter for PC PA25010 9809 C 0147495 TOSHIBA - List of cables used No. Name Length (m) Shield Remarks Cable Connector 1 Antenna cable (CA-RSPNMA004) 1.2 Shielded Shielded Jacket diameter 4.95mm 2 Antenna cable (CA-RSPNMA010) 3.0 Shielded Shielded Jacket diameter 4.95mm 3 Antenna cable (CA-NMNFA004) 1.2 Shielded Shielded Jacket diameter 4.95mm 4 Antenna cable (CA4NMRSF020) 6.0 Shielded Shielded Jacket diameter 10.29mm 5 Coaxial Cable 0.08 Shielded Shielded With Ferrite Core: SC-10-5-10 (TKK), 2 turn 6 Coaxial Cable 0.12 Shielded Shielded With Ferrite Core: SC-10-5-10 (TKK), 2 turn 7 LAN cable (STP, Cat.5e) 11.7 Shielded Shielded - 8 LAN cable (STP, Cat.5e) 11.7 Shielded Shielded - 9 DC cable 1.2 Unshielded Unshielded - 10 AC cable 1.8 Unshielded Unshielded - 11 DC cable 1.0 Unshielded Unshielded - 12 AC cable 2.0 Unshielded Unshielded - UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124

Test report No. : 28CE0213-HO-01-A Page : 13 of 94 Issued date : February 25, 2008 FCC ID : N6C-SX10WAG SECTION 5: Conducted Emission 5.1 Operating environment Test place : No.4 semi anechoic chamber. Temperature : See data Humidity : See data 5.2 Test configuration EUT was placed on a urethane platform of nominal size, 0.5m by 1.0m, raised 80cm above the conducting ground plane. The rear of tabletop was located 40cm to the vertical conducting plane. The rear of EUT and its peripherals was aligned and flushed with rear of tabletop. All other surfaces of tabletop were at least 80cm from any other grounded conducting surface. EUT was located 80cm from the LISN/AMN and excess AC cable was bundled in center. I/O cables that were connected to the other peripherals were bundled in center. They were folded back and forth forming a bundle 30cm to 40cm long and were hanged at a 40cm height to the ground plane. Each EUT current-carrying power lead, except the ground (safety) lead, was individually connected through a LISN/AMN to the input power source. All unused 50 ohm connectors of the LISN/AMN were resistivity terminated in 50 ohm when not connected to the measuring equipment. A drawing of the set up is shown in the photos of APPENDIX 1. Frequency range : 0.15 MHz-30MHz EUT position : Table top EUT operation mode : See Clause 4.1 5.3 Test procedure The AC Mains Terminal Continuous disturbance Voltage has been measured with the EUT within a semi anechoic chamber. The EUT was connected to a Line Impedance Stabilization Network (LISN)/ Artificial Mains network (AMN). An overview sweep with peak detection has been performed. The measurements have been performed with a quasi-peak detector and if required, with an average detector. The conducted emission measurements were made with the following detector function of the test receiver. Detector Type : Quasi-Peak and Average IF Bandwidth : 9 kHz 5.4 Test result Summary of the test results: Pass Date: February 19 to 20, 2008 Test engineer: Kenichi Adachi UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124

Test report No. : 28CE0213-HO-01-A Page : 14 of 94 Issued date : February 25, 2008 FCC ID : N6C-SX10WAG SECTION 6: Spurious Emission and Band Edge Compliance [Radiated] Test Procedure EUT was placed on a urethane platform of nominal size, 0.5m by 1.0m, raised 80cm above the conducting ground plane. The Radiated Electric Field Strength intensity has been measured in a Semi Anechoic Chamber with a ground plane and at a distance of 3m(Below 10GHz) , 1m(10-26.5GHz, Distance Factor : 20log(3[m]/1[m])) and 0.5m( Upper 26.5GHz, Distance Factor : 20log(3[m]/0.5[m] ). The height of the measuring varied between 1 and 4m and EUT was rotated a full revolution in order to obtain the maximum value of the electric field intensity. The measurements were performed for both vertical and horizontal antenna polarization with the Test Receiver or the Spectrum Analyzer. Below 1GHz The result also satisfied with the general limits specified in section 15.209(a). Above 1GHz Inside of the restricted bands (Section 15.205): Apply to limit in the Section 15.209(a) Outside of the restricted bands (Section 15.407): Limit –27dBm EIRP –17dBm EIRP (5.725-5.825GHz Band Edge) Frequency Below 1GHz Above 1GHz Above 1GHz (Inside of the restricted bands) (Outside of the restricted bands) Instrument usedTest Receiver Spectrum Analyzer Spectrum Analyzer Detector QP: BW 120kHz PK: RBW:1MHz/VBW: 1MHz RBW:1MHz/VBW: 1MHz IF Bandwidth AV: RBW:1MHz/VBW:10Hz Test data : APPENDIX 2 Test result : Pass - The carrier level and noise levels were confirmed at each position of X, Y and Z axes of EUT’s module to see the position of maximum noise, and the test was made at the position that has the maximum noise. - The test was made on EUT’s Antenna at the normal use position. SECTION 7: Maximum Peak Output Power Test Procedure The Peak Transmit Power was measured with a spectrum analyzer connected to the antenna port. The test was made with the spectrum analyzer that has a function of channel-power measurement. Test data : APPENDIX 2 Test result : Pass UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124


Document Created: 2008-02-27 15:42:56
Document Modified: 2008-02-27 15:42:56
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC