RF Exposure Info

FCC ID: N4ZUFO01FPVRX00

RF Exposure Info

Download: PDF
FCCID_3639706

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch No. 1 Workshop, M-10, Middle section, Science & Technology Park, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Report No.: SZEM170800874105 Fax: +86 (0) 755 2671 0594 Email: ee.shenzhen@sgs.com Page: 1 of 6 1 Cover page SAR Evaluation Report Application No.: SZEM1708008741CR Applicant: Flysky RC Model technology Co., Ltd Address of Applicant: West building 3, Huangjinyuan Ind Park, Qiaoli North Gate, Changping Town, Dongguan, China Manufacturer: KYOSHO CORPORATION Address of Manufacturer: 153 FunaKo Atsugi, Kanagawa 243-0034, JAPAN Factory: Flysky RC Model technology Co., Ltd Address of Factory: West building 3, Huangjinyuan Ind Park, Qiaoli North Gate, Changping Town, Dongguan, China Equipment Under Test (EUT): EUT Name: FPV wireless video transmission system Model No.: 82724 FCC ID: N4ZUFO01FPVRX00 Standard(s) : 47 CFR Part 1.1307 47 CFR Part 2.1093 KDB447498D01 General RF Exposure Guidance v06 Date of Receipt: 2017-08-21 Date of Test: 2017-09-09 to 2017-10-17 Date of Issue: 2017-10-26 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160600474102 Page: 2 of 6 2 Version Revision Record Version Chapter Date Modifier Remark 01 2017-10-26 Original Authorized for issue by: Harry Wu /Project Engineer Eric Fu /Reviewer This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160600474102 Page: 3 of 6 3 Contents Page 1 COVER PAGE .....................................................................................................................................................1 2 VERSION..............................................................................................................................................................2 3 CONTENTS ..........................................................................................................................................................3 4 GENERAL INFORMATION ................................................................................................................................4 4.1 GENERAL DESCRIPTION OF EUT ..........................................................................................................................4 4.2 TEST LOCATION ..................................................................................................................................................5 4.3 TEST FACILITY ...................................................................................................................................................5 4.4 DEVIATION FROM STANDARDS ............................................................................................................................5 4.5 ABNORMALITIES FROM STANDARD CONDITIONS ..................................................................................................5 4.6 OTHER INFORMATION REQUESTED BY THE CUSTOMER .........................................................................................5 5 SAR EVALUATION .............................................................................................................................................6 5.1 RF E XPOSURE COMPLIANCE REQUIREMENT .........................................................................................................6 5.1.1 Standard Requirement ...........................................................................................................................6 5.1.2 Limits .......................................................................................................................................................6 5.1.3 EUT RF Exposure ..................................................................................................................................6 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160600474102 Page: 4 of 6 4 General Information 4.1 General Description of EUT Power supply: DC 3.7V (1 x DC3.7V Li-Po battery) Test voltage: DC 3.7V Modulation Technique: FHSS Frequency Range: 2.4006GHz to 2.474GHz Modulation Type: GFSK Antenna Type: Integral Antenna Gain: 2 dBi Channel List(MHz): 2409.5 2413 2416.5 2420 2423.5 2427 2430.5 2434 2437.5 2441 2444.5 2448 2451.5 2455 2458.5 2462 2465.5 2469 2472.5 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160600474102 Page: 5 of 6 4.2 Test Location All tests were performed at: SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch No. 1 Workshop, M-10, Middle section, Science & Technology Park, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 No tests were sub-contracted. 4.3 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • CNAS (No. CNAS L2929) CNAS has accredited SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC Lab to ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration Laboratories (CNAS-CL01 Accreditation Criteria for the Competence of Testing and Calibration Laboratories) for the competence in the field of testing. • A2LA (Certificate No. 3816.01) SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory is accredited by the American Association for Laboratory Accreditation(A2LA). Certificate No. 3816.01. • VCCI The 10m Semi-anechoic chamber and Shielded Room of SGS-CSTC Standards Technical Services Co., Ltd. have been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: G-823, R-4188, T-1153 and C-2383 respectively. • FCC –Designation Number: CN1178 SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been recognized as an accredited testing laboratory. Designation Number: CN1178. Test Firm Registration Number: 406779. • Industry Canada (IC) Two 3m Semi-anechoic chambers and the 10m Semi-anechoic chamber of SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC Lab have been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 4620C-1, 4620C-2, 4620C-3. 4.4 Deviation from Standards None. 4.5 Abnormalities from Standard Conditions None. 4.6 Other Information Requested by the Customer None. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS—CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZENM160500474102 Page sots 5 SAR Evaluation 5.1 RF Exposure Compliance Requirement 5.1.1 Standard Requirement According to KOB447498001 General RF Exposire Guicknce v08 4.8.1. Sandalone SARt est exclusion considertions Unless speciiealy requtied by the publshed RF axposure KDB procedures, standalone 1—g hesel or bacy and 10.q axtramty SAR avaluationor general popultion exposure conditons, by messurement or numerical smultion, is nt reaured when the corponing SAR Exclusion Thresholi conditon, ted balon,i satatled 5.1.2Limits "The 1—a and 109 SAR test oxclusion throsholds for 100 NHlz t 8 GHattest separation stances £50 mm are determinad by: I(max. powar of channal, inlucing tine—up tolerance, mW)Ifmin. test epration distance,mm}]° [M(GHtz] s 8.0for .9 SAR andls 7.5 for 10.4 extromty SAR, where 1(GHz) is the RF channetransmt freguency in Géte Powar and distance are rounded tothe nearest mW and mm before calcultion‘" "The resultis roundad to one decimel pace for comparison "The test exclusions are appleable only when the minimum test separaton ditanceis < 50mm and for transnmission racunciesbatween 100 MH and 6 Giz. When the minimum test separation eistance is < 5 mm, a eitence o 3 mm is appled tdetermine SAR test exclusion 5.1.3EUT RF Exposure The Max Condicted Peak Outpot Power is 640. dBm on e lowest channel24 GHfz 6440 dBm logaithmic terms convertto numeric resul s nearly 4.87mW According tothe formula. caleulte the ost exclsion thresholds {{max. powar of channel,inclucing tuneup tolerance, mW)/ (min.tet separation distance, mm— PH(GHe] General RF Expasire = (4.87 mW /5 mm} x 124005 GHHe = (n SA requrement s=30 @ (n<@ So the SAFt reportis norequired


Document Created: 2017-10-31 07:33:49
Document Modified: 2017-10-31 07:33:49
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC