Users Manual

FCC ID: N4ZFTR1000

Users Manual

Download: PDF
FCCID_4057541

| ~&r42 Introduction | MMoXRaAHDs 3 (@=Real¥ikEAA) . FxtX FTr10 adopts AFHDS 3, Flysky‘s third—generation automatic | hit. exteieitorbessiid , artathinef: Pm eS frequency hopping digital system. It uses a double—antenna | iBus 5. bidirectional transmission system and is uniquely designed to save space and output standard PPM and i—BUS signals. | EeeT RFESRKYLSRERAETNEMt. CH 2—2H 10 CH 1— CH 9 SENS : iEkes/tmes. SENS SENVO : iBE i—BUS i# , 1GiBk. CH 1— CH 10 : iBEREH. HirsatEftSsMt. BIND : }EBEXIfS&. Feif : JGHefREE. Antenna Ports used to connect the receiver to the various components. SENS: Connects to sensors. SENVO: Connectsto the i—BUS module for channel expansion. CH 1 — CH 10: Connects the servos, power supply or other LED components. BIND: For bind cable. Power: Flight controller power output. > itaksin : ERpipmir*rm—sk=zstch , allopESHR=At,"sRh,. KXARM . REDCXAMIRENNREIER , RnXHARRIN. IRXMARNNEIRNIREENIULAERELTE . RHaofitSmEritsXki<ats3] #AtzrT{Eio5lRA RirEiltZtinsei , BA/alsseatto"iREedENIER. itXtriceSE, dliin#lstemiciamn. /oriefesintcs_/f eiplrnelktitmsstr.z2id#€>6 1 EKE—AvIEs. Reitist , iselsisittisif , efolértrnosNiinX. * Attention: Make sure the product is installed and calibrated correctly, failure to do so may result in serious injury. Make sure the receiver‘s battery is disconnected before turning off the transmitter, failure to do so may lead to unintended operation or loss of control. Make sure the receiver is mounted away from motors, electronic speed controllers or any device that emits excessive electrical noise. Keep the receiver‘s antenna at least 1cm away from conductive materials such as carbon or metal. Do not power on the receiver during the setup process to prevent loss of control. IEEXZD . Insert the bind cable into the receivers BIND port; 1. 1§S15&k1@/. BIND 0 ; 2. sHiF&inHitIEIB0 , RikxtVerIkiAEn#)xts . Plug the power cable into any other port, and the receiver‘s LED will start to flash quickly indicating that it has entered K8 ; bind mode. BARENUIRAMTSHKA ; CARHNURANMHSHKAESISS—.OEET . Put the transmitter into bind mode; (See the transmitter‘s B . eiRRRAEMATERREARRRAITEEAEE ) instruction manual for more information) EKerIEAEREN , ENBASNMEMEIR . Binding is successful when the receiver‘s LED will stop flashing. ZLMNEAMERT. Remove the power and bind cables from the receiver. StiEERdtif4=!EILL . Reconnect the power cable to the receiver. Bbesstl. RKV. GEEfIERLE IESXXM .i3 . Check to make sure that the transmitter and receiver are SS—¥BSESXIXNH. working as expected, if there are any issues or unexpected operation follow the steps above to bind again. http://www.flysky—cn.com Copyright ©2018 Flysky Technology co., Itd

1 C * iBE1: 10 * Channels: 10 * EeBNE: AREZEZ / SHN / EAHV / ## ® ModelType: Fixed wing/ glider / helicopter / drone * HK!lRi®H: i.bus/PPM/PWM/UART ® Data Output: i.bus/PPM/PWM/UART * mXEBE: 2.402—2.480GHz ® Frequency Range: 2.402—2.480GHz * ZHHIJ%: <20dBm (EU) * Transmission Power: <20dBm{(EU) * RFIinfE: AFHDS 3 ® RF standard: AFHDS 3 * XLHRKBE: 103 SX *2(WNXHK) MEX * Antenna: 103mm*2 * HiAnBi®: 3.5V ~12V * Input Power: 3.5V ~ 12V * Hnxn/jm: LED tm ® Display: LED Indicator e L4XENM: 6 * Online Update: Yes * 4MNBRt: 52*28*22mm *© Dimensions: 52*28*22mm e NMSEE: 22¢g ® Weight: 22g e ZXIIAME: CE, FCC ID: N4ZFTR1O000 ® Certification: CE, FCC ID: N4ZFTR1O0O0 I itEX Certification FCC Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user‘ s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. EU DoC Declaration Hereby, [Flysky Technology co., Itd] declares that the Radio Equipment [FTR10] is in compliance with RED 2014/53/EU. The full text of the EU DoC is available at the following internet address: wwwflysky—cn.com. RF Exposure Compliance This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co—located or operating in conjunction with any other antenna or transmitter. Environmentally friendly disposal Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances. &A CE FCC ID : N4ZFTR1000 http://www.flysky—cn.com Copyright ©2018 Flysky Technology co., Itd


Document Created: 2018-10-31 09:48:48
Document Modified: 2018-10-31 09:48:48
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC