Users Manual

FCC ID: N4ZFRM30100

Users Manual

Download: PDF
FCCID_4090473

r*=ce7jt2 Introduction FRM3O01 ¥H AFHDS 3 ( E=RNB—BDMNMKTFAK ) , WX FRM301 adopts AFHDS 3, Flysky‘s third—generation KENOIER , #I/NDG , *H#FMaStA. automatic frequency hopping digital system. Dual antenna bidirectional transmission in a compact design with support for multiple signal inputs. s Overview Sport Bind GND LED PPM/RX : PPM fESH#H. GND : 3b +5V +5V : fEEEC Antenna Head/TX PPM /RX: PPM signal input. GND: Ground. PPM/RX +5V;: Power. Antenna > itRSEIn : (CERApiifatrmSRREIER , allofESHERRAEESIRA. XAR , BEDMCXAENNLEE , ReXMARNNL MERXAARANNEIRNENIUAIRELTE , SE6dodftSHErisEs KHiat#5| SAT(Em5 ARSH. TilrizlltRe=fiaseWL , bAbisReattB*IREAAEAYEE. BXASicSSREHH , Hlin#eteftiminmF. / riRtesimic#Uff , inibiRisilttifhersttrz202>6 1e3 HA—AMIfEE. RExdBEd , sttRRE , twE~GEATmE. » Attention: Make sure the product is installed and calibrated correctly, failure to do so may result in serious injury. Make sure the receiver‘s battery is disconnected before turning off the transmitter, failure to do so may lead to unintended operation or loss of control. Make sure the receiver is mounted away from motors, electronic speed controllers or any device that emits excessive electrical noise. Keep the receiver‘s antenna at least 1cm away from conductive materials such as carbon or metal. Do not power on the receiver during the setup process to prevent loss of control. xn3 Binding SfErIIEZEORANM , Rovt\ANRBIRE ; The status indicator will flash quickly when the module is SETrIREERN , Raod4iBAcX) : in bind mode. When the status indicator turns solid green the module HETVJLIEIEAN , rshatn ; has bound successfully. TEnJJZLEAREOXX—XH , KaitIHRIKE. If the status indicator is slowly flashing red it means the module is not bound. _ toxifGeni . &ctftlnl$ FRV3O1 MessSRIINLL. If the status indicator flashes 3 times followed by a pause ~— NMNMSkENE. the module is in firmware update mode. _ eisfonn® , Klk 10 XMRSmUSEREXTIAE. +« Before binding make sure that the FRM301 module is installed correctly. « Press the bind button quickly to enter bind mode. « Do not press and hold the bind button unless you wish to enter firmware update mode. Press and hold the bind button for 10 seconds to enter firmware update mode. http://www.flysky—cn.com Copyright ©2018 Flysky Technology co., Itd

1 C * ESBMA!: Paladin PL18 Model Type: Paladin PL18 * WIiE!f®H: i.bus/PPM/PWM/UART Data Output: i.bus/PPM/PWM/UART * m*CE: 2.402—2.480GHz Frequency Range: 2.402—2.480GHz * #LRI%E: <20dBm (EU) Transmission Power: <20dBm{(EU) * 24G z: AFHDS 3 2A4GHz Protocol: AFHDS 3 o XRXE: EYX Antenna: Dual antenna * HiABiJZ: 5V DC Input Power: 5V DC * Rxrpn: LED tir Display: LED Indicator e fZEX: 6 Online Update: Yes e MBR: 52*30*12.3mm Dimensions: 52*30*12.3mm * 1NMEEES: l6g Weight: 16g e ZZMIMHE: CE, FCC ID: N4ZFRM30100 Certification: CE, FCC ID: N4ZFRM30100 | nseEse200 FCC Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user‘ s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. EU DoC Declaration Hereby, [Flysky Technology co., Itd] declares that the Radio Equipment [FRM301] is in compliance with RED 2014/53/EU. The full text of the EU DoC is available at the following internet address: www.flysky—cn.com. RF Exposure Compliance This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co—located or operating in conjunction with any other antenna or transmitter. Environmentally friendly disposal Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances. & ce FCC ID : N4ZFRM30100 http://www.flysky—cn.com Copyright ©2018 Flysky Technology co., Itd


Document Created: 2018-10-31 09:48:01
Document Modified: 2018-10-31 09:48:01
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC