User Manual

FCC ID: MY5ATOM2

Users Manual

Download: PDF
FCCID_3808884

1. Press the [Set] button for one second, and release the button when the blue LED flashes slowly. 2. Program a Remote: Within 30 seconds, press any button - + on the remote that you would like to program to the opener. 3. Once the button on the remote is programmed. The blue LED will off indicating the programming successfully. 1. Press the [Set] button for 15 seconds, when the blue LED flashes quickly. Release the [Set] button. 2. Press the [Set] button again to confirm erase all the programmed remotes. 3. The blue LED stays off and emit one beep indicating the erasing 1. Re-connect the wires of the successfully. safety beam sensor to the Atoms opener. Push in tab with a flat head screwdriver and insert the wires. - + + - - + + + + 1. Wall Console Push the button to open/close the garage 2. Re-connect the wires of the wall door opener. console to the Atoms opener. Push in tab with a flat head screwdriver and insert the wires. + - 2. Remote + - - + + + + To open/close the opener with remote control, press the button that is programmed to the opener. 1. Connect the opener to an approved FCC power source. The green LED stays This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: on. (1) This device may not cause harmful interference and (2) This device must accept any interference SET received, including interference that may cause undesired operation. - Warning: + 1 2 3 Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Green Note: LED This equipment has been tested and found to comply with the limits for a Class B digital device, 2. Press and hold [Set] button for 5 pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against seconds until the blue LED stays on, harmful interference in a residential installation. This equipment generates, uses and can radiate radio red LED flashes quickly. Release the frequency energy and, if not installed and used in accordance with the instructions, may cause harmful [SET] button. interference to radio communications. SET However, there is no guarantee that interference will not occur in a particular installation. If this 3. Press the [ ] button until the door is in fully open position. - equipment does cause harmful interference to radio or television reception, which can be determined + - - by turning the equipment off and on, the user is encouraged to try to correct the interference by one or + + 1 2 3 4. Press the [Set] button to confirm the more of the following measures: door position. • Reorient or relocate the receiving antenna. Red Blue • Increase the separation between the equipment and receiver. LED LED • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 5. The blue LED stays on, red LED • Consult the dealer or an experienced radio/TV technician for help. flashes slowly. 6. Press the [ ] button until the FCC door is in fully closed position. SET Ce dispositif est conforme à la partie 15 des règlements de la FCC. Son fonctionnement est soumis aux deux conditions suivantes : 1) Il ne doit pas produire d’interférences nuisibles, et 2) II doit accepter toute 7. Press the [Set] button again to confirm. - interférence reçue, même si celle-ci est susceptible de compromettre son fonctionnement. + - - + + 1 2 3 8. The blue and red LED stay on. AVERTISSEMENT : Tout changement ou modification, non expressément approuvé par la partie responsable de The light will flash 3 times when the Red Blue la conformité, peut annuler l'autorisation de l'utilisateur à utiliser cet appareil. travel limit settings are completed. LED LED Remarque : Cet équipement a été testé et déclaré conforme aux restrictions prévues dans le cadre de la classe B des 9. Press the Wall button to open the appareils numériques, définies par la section 15 du règlement de la FCC. Ces restrictions visent à garantir garage door to its fully open position. une protection suffisante contre les interférences nuisibles dans une installation à domicile. Cet appareil outilise et émet de l'énergie de fréquences radio, et s’il n’est pas installé et employé conformément aux 10. The blue and red LED flash slowly. SET consignes, il peut provoquer des interférences nuisibles aux communications radio. - Il n'existe toutefois aucune garantie que de telles interférences ne se produiront pas dans une installation 11. The light will flash 3 times again. + - - particulière. Si cet appareil occasionne des interférences nuisibles aux réceptions radio ou télévisuelles, + + 1 2 3 ce qui peut être déterminé en mettant l'appareil en arrêt et en marche, l’utilisateur peut corriger cette interférence de l'une des façons suivantes : Red Blue LED LED • Réorientez ou déplacez l'antenne de réception. • Augmentez la distance entre l'appareil et le récepteur. 12. Press the Wall button again to close • Branchez l'appareil sur un circuit électrique différent de celui où le récepteur est branché. the garage door to its fully closed • Consultez le fournisseur ou un technicien radio/télévision expérimenté pour obtenir de l’aide. position. 13. The blue and red LED will turn off. And SET IC emit one beep indicating the - This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the + - - following two conditions: + + 1 2 3 programming successfully. (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux Partie 15 des règlements de la FCC et CNR d'Industrie Canada CANADA OFFICE http://www.skylinkhome.com US OFFICE applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions 17 Sheard Avenue, Brampton, 1180-D East Francis Street, suivantes : Ontario, Canadá L6Y 1J3 Ontario, CA 91761, USA (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est E-mail: support@skylinkhome.com © 2018 SKYLINK GROUP susceptible d'en compromettre le fonctionnement.


Document Created: 2018-04-06 11:26:53
Document Modified: 2018-04-06 11:26:53
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC