FCC Part 1.1310 Test Report

FCC ID: MTD-0006

RF Exposure Info

Download: PDF
FCCID_3905293

Test Report Prepared for: Time Keeping Systems Inc. Model: TAG-006 Description: Body Worn Location Device Serial Number: N/A FCC ID: MTD-0006 To FCC Part 1.1310 Date of Issue: June 25, 2018 On the behalf of the applicant: Time Keeping Systems Inc. 30700 Bainbridge Rd Cleveland, OH 44139 Attention of: Blair Hamilton, Engineering Consultant Ph: (216)595-1026 Email: dchriss@guard1.com Prepared By Compliance Testing, LLC 1724 S. Nevada Way Mesa, AZ 85204 (480) 926-3100 phone / (480) 926-3598 fax www.compliancetesting.com Project No: p1850027 Kenneth Lee Project Test Engineer This report may not be reproduced, except in full, without written permission from Compliance Testing All results contained herein relate only to the sample tested p1850027_FCC_Part 1.1310_Rev 2.0 Page 1 of 4

Test Report Revision History Revision Date Revised By Reason for Revision 1.0 June 19, 2018 Kenneth Lee Original Document Updated the term BLE to GFSK in additional 2.0 June 25, 2018 Kenneth Lee Information p1850027_FCC_Part 1.1310_Rev 2.0 Page 2 of 4

ILAC / A2LA Compliance Testing, LLC, has been accredited in accordance with the recognized International Standard ISO/IEC 17025:2005. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer joint ISO-ILAC-IAF Communiqué dated January 2009) The tests results contained within this test report all fall within our scope of accreditation, unless below Please refer to http://www.compliancetesting.com/labscope.html for current scope of accreditation. Testing Certificate Number: 2152.01 FCC Site Reg. #349717 IC Site Reg. #2044A-2 Non-accredited tests contained in this report: N/A EUT Description Model: TAG-006 Description: Body Worn Location Device Firmware: N/A Software: N/A Serial Number: N/A Antenna Gain: -1.6 dBi Additional Information: The EUT implements GFSK. p1850027_FCC_Part 1.1310_Rev 2.0 Page 3 of 4

SAR Exclusion The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR,25 where • f(GHz) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation26 • The result is rounded to one decimal place for comparison • 3.0 and 7.5 are referred to as the numeric thresholds in the step 2 below The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to 5) in section 4.1 is applied to determine SAR test exclusion. Max Power in mW = 2.26 mW Antenna Gain = -1.6 dB Power with antenna gain = 1.57 mW Min. Test Separation Distance = 1 mm Frequency of Operation = 2426 MHz The antenna gain of the device is negative; therefore the conducted output power was used for the final calculation. 2.26 𝑚𝑊 X√2.426 = 0.70401811 5 𝑚𝑚 END OF TEST REPORT p1850027_FCC_Part 1.1310_Rev 2.0 Page 4 of 4


Document Created: 2018-06-25 16:07:08
Document Modified: 2018-06-25 16:07:08
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC