RF Test Report-BLE

FCC ID: MSQA006

Test Report

Download: PDF
FCCID_3454709

FCC Test Report Report No.: RF170428C03-1 FCC ID: MSQA006 Test Model: ASUS_A006 Received Date: Apr. 28, 2017 Test Date: May 22, 2017 ~ May 26, 2017 Issued Date: Jun. 02, 2017 Applicant: ASUSTek COMPUTER INC. Address: 4F, No. 150, LI-TE Rd., PEITOU, TAIPEI 112, TAIWAN Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C ) Test Location (1): No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. Test Location (2): No.215, Sec. 3, Beixin Rd., Xindian Dist., New Taipei City 231, Taiwan, R.O.C This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Report No.: RF170428C03-1 Page No. 1 / 33 Report Format Version: 6.1.1

Table of Contents Release Control Record .................................................................................................................................. 4 1 Certificate of Conformity ........................................................................................................................... 5 2 Summary of Test Results ........................................................................................................................... 6 2.1 Measurement Uncertainty ..................................................................................................................... 6 2.2 Modification Record .............................................................................................................................. 6 3 General Information ................................................................................................................................... 7 3.1 General Description of EUT .................................................................................................................. 7 3.2 Description of Test Modes..................................................................................................................... 8 3.2.1 Test Mode Applicability and Tested Channel Detail .................................................................... 9 3.3 Description of Support Units ................................................................................................................ 11 3.3.1 Configuration of System under Test .......................................................................................... 11 3.4 General Description of Applied Standards ........................................................................................... 11 4 Test Types and ResultsSDR660 .............................................................................................................. 12 4.1 Radiated Emission and Bandedge Measurement .............................................................................. 12 4.1.1 Limits of Radiated Emission and Bandedge Measurement ..................................................... 12 4.1.2 Test Instruments ....................................................................................................................... 13 4.1.3 Test Procedures ........................................................................................................................ 14 4.1.4 Deviation from Test Standard ................................................................................................... 14 4.1.5 Test Set Up ............................................................................................................................... 15 4.1.6 EUT Operating Conditions ........................................................................................................ 15 4.1.7 Test Results .............................................................................................................................. 16 4.2 Conducted Emission Measurement .................................................................................................... 20 4.2.1 Limits of Conducted Emission Measurement ........................................................................... 20 4.2.2 Test Instruments ....................................................................................................................... 20 4.2.3 Test Procedures ........................................................................................................................ 20 4.2.4 Deviation from Test Standard ................................................................................................... 20 4.2.5 TEST SETUP............................................................................................................................ 21 4.2.6 EUT Operating Conditions ........................................................................................................ 21 4.2.7 Test Results .............................................................................................................................. 22 4.3 6 dB Bandwidth Measurement ............................................................................................................ 24 4.3.1 Limits of 6 dB Bandwidth Measurement ................................................................................... 24 4.3.2 Test Setup ................................................................................................................................. 24 4.3.3 Test Instruments ....................................................................................................................... 24 4.3.4 Test Procedure ......................................................................................................................... 24 4.3.5 Deviation fromTest Standard .................................................................................................... 24 4.3.6 EUT Operating Conditions ........................................................................................................ 24 4.3.7 Test Result ................................................................................................................................ 25 4.4 Conducted Output Power Measurement ............................................................................................ 26 4.4.1 Limits of Conducted Output Power Measurement.................................................................... 26 4.4.2 Test Setup ................................................................................................................................. 26 4.4.3 Test Instruments ....................................................................................................................... 26 4.4.4 Test Procedures ........................................................................................................................ 26 4.4.5 Deviation from Test Standard ................................................................................................... 26 4.4.6 EUT Operating Conditions ........................................................................................................ 26 4.4.7 Test Results .............................................................................................................................. 26 4.5 Power Spectral Density Measurement ............................................................................................... 27 4.5.1 Limits of Power Spectral Density Measurement ....................................................................... 27 4.5.2 Test Setup ................................................................................................................................. 27 4.5.3 Test Instruments ....................................................................................................................... 27 4.5.4 Test Procedure ......................................................................................................................... 27 4.5.5 Deviation from Test Standard ................................................................................................... 27 4.5.6 EUT Operating Condition ......................................................................................................... 27 4.5.7 Test Results .............................................................................................................................. 28 Report No.: RF170428C03-1 Page No. 2 / 33 Report Format Version: 6.1.1

4.6 Conducted Out of Band Emission Measurement ............................................................................... 29 4.6.1 Limits of Conducted Out of Band Emission Measurement ....................................................... 29 4.6.2 Test Setup ................................................................................................................................. 29 4.6.3 Test Instruments ....................................................................................................................... 29 4.6.4 Test Procedure ......................................................................................................................... 29 4.6.5 Deviation from Test Standard ................................................................................................... 29 4.6.6 EUT Operating Condition ......................................................................................................... 29 4.6.7 TEST RESULTS ....................................................................................................................... 30 5 Pictures of Test Arrangements................................................................................................................ 32 Appendix – Information on the Testing Laboratories ................................................................................ 33 Report No.: RF170428C03-1 Page No. 3 / 33 Report Format Version: 6.1.1

Release Control Record Issue No. Description Date Issued RF170428C03-1 Original Release Jun. 02, 2017 Report No.: RF170428C03-1 Page No. 4 / 33 Report Format Version: 6.1.1

1 Certificate of Conformity Product: ASUS Phone Brand: ASUS Test Model: ASUS_A006 Sample Status: Identical Prototype Applicant: ASUSTek COMPUTER INC. Test Date: May 22, 2017 ~ May 26, 2017 Standards: 47 CFR FCC Part 15, Subpart C (Section 15.247) ANSI C63.10:2013 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. Prepared by : , Date: Jun. 02, 2017 Ivonne Wu / Supervisor Approved by : , Date: Jun. 02, 2017 David Huang / Project Engineer Report No.: RF170428C03-1 Page No. 5 / 33 Report Format Version: 6.1.1

ommert 2 Summary of Test Results 47 CFR FCC Part 15, Subpart C (Section 15.247) FCC Test Item Result Remarks Clause Meet the requirement of limit. 15.207 AC Power Conducted Emission Pass Minimum passing margin is —26.60 dB at 0.69400 MHz. Meet the requirement of limit. 15.205 & 209 Radiated Emissions Pass Minimum passing margin is —12.11 dB at 2496.80 MHz. 15.247(d) Band Edge Measurement Pass Meet the requirement of limit. 15.247(d) Antenna Port Emission Pass Meet the requirement of limit. 15.247(a)(2) 6 dB Bandwidth Pass Meet the requirement of limit. 15.247(b) Conducted power Pass Meet the requirement of limit. 15.247(e) Power Spectral Density Pass Meet the requirement of limit. 15.203 Antenna Requirement Pass No antenna connector is used. 2.1 Measurement Uncertainty Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT: The listed uncertainties are the worst case uncertainty for the entire range of measurement. Please note that the uncertainty values are provided for informational purposes only and are not used in determining the PASS/FAIL results. Messurement F Expended Uncertainty requenc quency (k=2) (4) Conducted Emissions at mains ports 150 kHz ~ 30 MHz 244 dB 30 MHz ~ 200 MHz 2.0153 dB Radiated Emissions up to 1 GHz 200 MHz ~1000 MHz 2.0224 dB 1 GHz ~ 18 GHz 1.0121 dB Radiated Emissions above 1 GHz 18 GHz ~ 40 GHz 1.1508 dB 2.2 Modification Record There were no modifications required for compliance. Report No.: RF170428C03—1 Page No. 6 / 33 Report Format Version: 6.1.1

3 General Information 3.1 General Description of EUT Product ASUS Phone Brand ASUS Test Model ASUS_A006 Status of EUT Identical Prototype 5.0 Vdc (host equipment) Power Supply Rating 5.0 Vdc or 9 Vdc (adapter) 3.85 Vdc (Li-ion battery) Modulation Type GFSK Transfer Rate 1 Mbps Operating Frequency 2402 ~ 2480 MHz Number of Channel 40 Output Power 1.236 mW Antenna Type PIFA antenna with -2 dBi gain Antenna Connector N/A Accessory Device Refer to Note as below Data Cable Supplied Refer to Note as below Note: 1. The EUT’s accessories list refers to Ext. Pho. 2. The above EUT information is declared by manufacturer and for more detailed features description, please refer to the manufacturer's specifications or User's Manual. Report No.: RF170428C03-1 Page No. 7 / 33 Report Format Version: 6.1.1

3.2 Description of Test Modes 40 channels are provided to this EUT: Channel Freq. (MHz) Channel Freq. (MHz) Channel Freq. (MHz) Channel Freq. (MHz) 0 2402 10 2422 20 2442 30 2462 1 2404 11 2424 21 2444 31 2464 2 2406 12 2426 22 2446 32 2466 3 2408 13 2428 23 2448 33 2468 4 2410 14 2430 24 2450 34 2470 5 2412 15 2432 25 2452 35 2472 6 2414 16 2434 26 2454 36 2474 7 2416 17 2436 27 2456 37 2476 8 2418 18 2438 28 2458 38 2478 9 2420 19 2440 29 2460 39 2480 Report No.: RF170428C03-1 Page No. 8 / 33 Report Format Version: 6.1.1

3.2.1 Test Mode Applicability and Tested Channel Detail EUT Configure Applicable To Description Mode RE1G RE<1G PLC APCM - √ √ √ √ - Where RE1G: Radiated Emission above 1 GHz RE<1G: Radiated Emission below 1 GHz PLC: Power Line Conducted Emission APCM: Antenna Port Conducted Measurement Note: The EUT had been pre-tested on the positioned of each 3 axis. The worst case was found when positioned on Y-plane. Note: “-”means no effect. Radiated Emission Test (Above 1 GHz): Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Configure Available Channel Tested Channel Modulation Type Data Rate (Mbps) Mode - 0 to 39 0, 19, 39 GFSK 1 Radiated Emission Test (Below 1 GHz): Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Configure Available Channel Tested Channel Modulation Type Data Rate (Mbps) Mode - 0 to 39 39 GFSK 1 Power Line Conducted Emission Test: Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Configure Available Channel Tested Channel Modulation Type Data Rate (Mbps) Mode - 0 to 39 39 GFSK 1 Report No.: RF170428C03-1 Page No. 9 / 33 Report Format Version: 6.1.1

Antenna Port Conducted Measurement: This item includes all test value of each mode, but only includes spectrum plot of worst value of each mode. Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Configure Available Channel Tested Channel Modulation Type Data Rate (Mbps) Mode - 0 to 39 0, 19, 39 GFSK 1 Test Condition: Applicable To Environmental Conditions Input Power Tested by RE1G 25 deg. C, 65 % RH 120 Vac, 60 Hz Charles Hsiao RE<1G 25 deg. C, 65 % RH 120 Vac, 60 Hz Charles Hsiao PLC 25 deg. C, 65 % RH 120 Vac, 60 Hz Getaz Yang APCM 25 deg. C, 65 % RH 3.85 Vdc Anson Lin Report No.: RF170428C03-1 Page No. 10 / 33 Report Format Version: 6.1.1

3.3 Description of Support Units The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. No. Product Brand Model No. Serial No. FCC ID 1. Earphone FUNKEY FK-130102 N/A N/A No. Signal Cable Description Of The Above Support Units 1. N/A Note: 1. All power cords of the above support units are non-shielded (1.8m). 3.3.1 Configuration of System under Test EUT (Power from AC Adapter) Earphone *Test Table 3.4 General Description of Applied Standards The EUT is a RF Product. According to the specifications of the manufacturer, it must comply with the requirements of the following standards: FCC Part 15, Subpart C (15.247) 558074 D01 DTS Meas Guidance v04 ANSI C63.10-2013 All test items have been performed and recorded as per the above standards. Note: The EUT has been verified to comply with the requirements of FCC Part 15, Subpart B, Class B (DoC). The test report has been issued separately. Report No.: RF170428C03-1 Page No. 11 / 33 Report Format Version: 6.1.1

4 Test Types and Results 4.1 Radiated Emission and Bandedge Measurement 4.1.1 Limits of Radiated Emission and Bandedge Measurement Radiated emissions which fall in the restricted bands must comply with the radiated emission limits specified as below table. Other emissions shall be at least 20 dB below the highest level of the desired power: Frequencies Field Strength Measurement Distance (MHz) (microvolts/meter) (meters) 0.009 ~ 0.490 2400/F (kHz) 300 0.490 ~ 1.705 24000/F (kHz) 30 1.705 ~ 30.0 30 30 30 ~ 88 100 3 88 ~ 216 150 3 216 ~ 960 200 3 Above 960 500 3 Note: 1. The lower limit shall apply at the transition frequencies. 2. Emission level (dBuV/m) = 20 log Emission level (uV/m). 3. For frequencies above 1000 MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20 dB under any condition of modulation. Report No.: RF170428C03-1 Page No. 12 / 33 Report Format Version: 6.1.1

4.1.2 Test Instruments Description & Due Date of Model No. Serial No. Date of Calibration Manufacturer Calibration Test Receiver N9038A MY52260177 Jun. 21, 2016 Jun. 20, 2017 Agilent Technologies Spectrum Analyzer FSU43 101261 Dec. 13, 2016 Dec. 12, 2017 ROHDE & SCHWARZ BILOG Antenna VULB9168 9168-472 Dec. 16, 2016 Dec. 15, 2017 SCHWARZBECK HORN Antenna 3117 00143293 Dec. 29, 2016 Dec. 28, 2017 ETS-Lindgren HORN Antenna BBHA 9170 9170-480 Dec. 14, 2016 Dec. 13, 2017 SCHWARZBECK Fixed Attenuator BW-N10W5+ NA Jul. 08, 2016 Jul. 07, 2017 Mini-Circuits Loop Antenna EM-6879 269 Aug. 11, 2016 Aug. 10, 2017 Preamplifier 310N 187226 Jun. 24, 2016 Jun. 23, 2017 Agilent Preamplifier 83017A MY39501357 Jun. 24, 2016 Jun. 23, 2017 Agilent Power Meter ML2495A 1232002 Sep. 08, 2016 Sep. 07, 2017 Anritsu Power Sensor MA2411B 1207325 Sep. 08, 2016 Sep. 07, 2017 Anritsu Cable-CH1-01(R RF signal cable FC-SMS-100-SM 5D-FB Jun. 24, 2016 Jun. 23, 2017 ETS-LINDGREN S-120+RFC-SMS -100-SMS-400) Cable-CH1-02(R RF signal cable 8D-FB FC-SMS-100-SM Jun. 24, 2016 Jun. 23, 2017 ETS-LINDGREN S-24) Software E3 NA NA NA BV ADT 8.130425b Antenna Tower NA NA NA NA MF Turn Table NA NA NA NA MF Antenna Tower &Turn Table Controller MF-7802 NA NA NA MF Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HsinTien Chamber 1. 3. The horn antenna and preamplifier (model: 83017A) are used only for the measurement of emission frequency above 1GHz if tested. 4. The FCC Site Registration No. is 149147. 5. The IC Site Registration No. is IC7450I-1. Report No.: RF170428C03-1 Page No. 13 / 33 Report Format Version: 6.1.1

4.1.3 Test Procedures a. The EUT was placed on the top of a rotating table 0.8 meters (for below 1 GHz) / 1.5 meters (for above 1 GHz) above the ground at 3 meter chamber room for test. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The height of antenna is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to quasi-peak detect function and specified bandwidth with maximum hold mode when the test frequency is below 1 GHz. f. The test-receiver system was set to peak and average detected function and specified bandwidth with maximum hold mode when the test frequency is above 1 GHz. If the peak reading value also meets average limit, measurement with the average detector is unnecessary. Note: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120 kHz & 360 kHz for Quasi-peak detection (QP) at frequency below 1 GHz. 2. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is 3 MHz for Peak detection (PK) at frequency above 1 GHz. 3. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is 1/T for Average (Duty cycle < 98 %) detection at frequency above 1 GHz. 4. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is 10 Hz (Duty cycle ≥ 98 %) for Average detection (AV) at frequency above 1 GHz. 5. All modes of operation were investigated and the worst-case emissions are reported. 4.1.4 Deviation from Test Standard No deviation. Report No.: RF170428C03-1 Page No. 14 / 33 Report Format Version: 6.1.1

4.1.5 Test Set Up <Frequency Range below 1 GHz> Ant. Tower 1-4m Variable 3m 10m EUT& Support Units Turn Table 80cm Ground Plane Test Receiver <Frequency Range above 1 GHz> Ant. Tower 1-4m Variable EUT& 3m Support Units Turn Table Absorber 150cm Ground Plane Test Receiver For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.1.6 EUT Operating Conditions a. Placed the EUT on the testing table. b. Set the EUT under transmission condition continuously at specific channel frequency. Report No.: RF170428C03-1 Page No. 15 / 33 Report Format Version: 6.1.1

ommert 4.1.7 Test Results ABOVE 1 GHz DATA : EUT Test Condition Measurement Detail Channel Channel 0 Frequency Range 1 GHz ~ 25 GHz Input Power 120 Vac, 60 Hz Detector Function Peak (PK) Average (AV) Environmental 25 deg. C, 65 % RH Tested By Charles Hsiao Conditions Antennal Polarity & Test Distance: Horizontal at 3 m Frequency Emission Read Limit Margin Antenna Cable Preamp Ant(Ienna Table (MHz) Level Level (dBuVim) (aB) Factor Loss (dB) Factor Height Angle Remark (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 2361.03 52.48 50.85 74 —21.52 31.76 5.37 35.5 170 354 Peak 2383.98 41.18 39.49 54 —~12.82 31.78 5.4 35.49 170 354 Average 2402 92.65 90.92 31.8 5.4 35.47 170 354 Average 2402 93.55 91.82 31.8 5.4 35.47 170 354 Peak 4804 38.11 30.02 54 —15.89 33.96 8.25 34.12 195 263 Average 4804 47.55 39.46 74 —26.45 33.96 8.25 34.12 195 263 Peak Antennal Polarity & Test Distance: Vertical at 3 m rrequenes| Emso® Pnd uin mage Aient oane TextP BP TE waney (MHz) (dBuV/m) (dBuV) (dBuV/im) (dB) (dB/m) Loss (dB) (dB) (cm) (Degree) 2342.58 51.82 50.25 74 2218 31.74 5.33 35.5 181 89 Peak 2386.77 41.46 39.75 54 1254 31.8 5.4 35.49 181 89 Average 2402 94.78 93.05 31.8 5.4 35.47 181 89 Average 2402 95.86 94.13 31.8 5.4 35.47 181 89 Peak 4804 39.24 31.15 54 —14.76 33.96 8.25 34.12 195 107 Average 4804 48.26 40.17 74 —25.74 33.96 8.25 34.12 195 107 Peak Remarks: 1. Emission Level = Read Level + Antenna Factor + Cable Loss — Preamp Factor Margin value = Emission level — Limit value 2. 2402 MHz: Fundamental frequency. Report No.: RF170428C03—1 Page No. 16 / 33 Report Format Version: 6.1.1

EUT Test Condition Measurement Detail Channel Channel 19 Frequency Range 1 GHz ~ 25 GHz Peak (PK) Input Power 120 Vac, 60 Hz Detector Function Average (AV) Environmental 25 deg. C, 65 % RH Tested By Charles Hsiao Conditions Antennal Polarity & Test Distance: Horizontal at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 2349.69 51.92 50.35 74 -22.08 31.74 5.33 35.5 170 354 Peak 2389.38 41.12 39.41 54 -12.88 31.8 5.4 35.49 170 354 Average 2440 93.63 91.78 31.85 5.46 35.46 170 354 Average 2440 94.89 93.04 31.85 5.46 35.46 170 354 Peak 2489 52.34 50.33 74 -21.66 31.9 5.53 35.42 170 354 Peak 2495.84 41.78 39.76 54 -12.22 31.9 5.53 35.41 170 354 Average Antennal Polarity & Test Distance: Vertical at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 2331.96 51.79 50.25 74 -22.21 31.73 5.33 35.52 181 89 Peak 2389.29 41.12 39.41 54 -12.88 31.8 5.4 35.49 181 89 Average 2440 95.71 93.86 31.85 5.46 35.46 181 89 Average 2440 96.78 94.93 31.85 5.46 35.46 181 89 Peak 2492.2 41.75 39.73 54 -12.25 31.9 5.53 35.41 181 89 Average 2495.84 52.28 50.26 74 -21.72 31.9 5.53 35.41 181 89 Peak Remarks: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level – Limit value 2. 2440 MHz: Fundamental frequency. Report No.: RF170428C03-1 Page No. 17 / 33 Report Format Version: 6.1.1

EUT Test Condition Measurement Detail Channel Channel 39 Frequency Range 1 GHz ~ 25 GHz Peak (PK) Input Power 120 Vac, 60 Hz Detector Function Average (AV) Environmental 25 deg. C, 65 % RH Tested By Charles Hsiao Conditions Antennal Polarity & Test Distance: Horizontal at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 2480 92.79 90.83 31.88 5.5 35.42 170 354 Average 2480 93.92 91.96 31.88 5.5 35.42 170 354 Peak 2493.28 52.03 50.01 74 -21.97 31.9 5.53 35.41 170 354 Peak 2496.8 41.89 39.87 54 -12.11 31.9 5.53 35.41 170 354 Average 4960 38.13 29.86 54 -15.87 33.99 8.29 34.01 196 153 Average 4960 47.57 39.3 74 -26.43 33.99 8.29 34.01 196 153 Peak Antennal Polarity & Test Distance: Vertical at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 2480 94.66 92.7 31.88 5.5 35.42 181 89 Average 2480 96.02 94.06 31.88 5.5 35.42 181 89 Peak 2497.6 51.58 49.56 74 -22.42 31.9 5.53 35.41 181 89 Peak 2498.2 41.63 39.61 54 -12.37 31.9 5.53 35.41 181 89 Average 4960 38.43 30.16 54 -15.57 33.99 8.29 34.01 127 166 Average 4960 47.84 39.57 74 -26.16 33.99 8.29 34.01 127 166 Peak Remarks: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level – Limit value 2. 2480 MHz: Fundamental frequency. Report No.: RF170428C03-1 Page No. 18 / 33 Report Format Version: 6.1.1

9 kHz ~ 30 MHz DATA: The amplitude of spurious emissions attenuated more than 20 dB below the permissible value is not required to be report. 30 MHz ~ 1 GHz WORST-CASE DATA: EUT Test Condition Measurement Detail Channel Channel 39 Frequency Range 30 MHz ~ 1 GHz Peak (PK) Input Power 120 Vac, 60 Hz Detector Function Quasi-peak (QP) Environmental 25 deg. C, 65 % RH Tested By Charles Hsiao Conditions Antennal Polarity & Test Distance: Horizontal at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 81.57 5.78 28.36 40 -34.22 8.47 1.11 32.16 185 124 Peak 144.75 12.7 33.86 43.5 -30.8 9.73 1.38 32.27 163 234 Peak 250.59 11.38 28.63 46 -34.62 13 1.85 32.1 148 107 Peak 428.8 16.34 28.36 46 -29.66 17.75 2.41 32.18 169 134 Peak 521.2 19.38 28.31 46 -26.62 20.51 2.7 32.14 185 127 Peak 743.1 22.75 28.46 46 -23.25 23.27 3.16 32.14 142 108 Peak Antennal Polarity & Test Distance: Vertical at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 55.11 23.15 47.21 40 -16.85 7.27 0.9 32.23 177 153 Peak 143.94 6.81 28.09 43.5 -36.69 9.61 1.38 32.27 196 148 Peak 234.93 9.71 27.66 46 -36.29 12.36 1.85 32.16 187 113 Peak 413.4 15.82 27.73 46 -30.18 17.88 2.41 32.2 159 137 Peak 638.1 21.94 29.07 46 -24.06 22.1 2.93 32.16 195 142 Peak 822.2 23.84 28.9 46 -22.16 23.5 3.38 31.94 138 109 Peak Remarks: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level – Limit value Report No.: RF170428C03-1 Page No. 19 / 33 Report Format Version: 6.1.1

4.2 Conducted Emission Measurement 4.2.1 Limits of Conducted Emission Measurement Conducted Limit (dBuV) Frequency (MHz) Quasi-peak Average 0.15 - 0.5 66 - 56 56 - 46 0.50 - 5.0 56 46 5.0 - 30.0 60 50 4.2.2 Test Instruments Description & Date Of Due Date Of Model No. Serial No. Manufacturer Calibration Calibration Test Receiver ESCI 100613 Nov. 21, 2016 Nov. 20, 2017 ROHDE & SCHWARZ RF signal cable (with 10dB PAD) 5D-FB Cable-cond1-01 Dec. 22, 2016 Dec. 21, 2017 Woken LISN ROHDE & SCHWARZ ESH3-Z5 835239/001 Mar. 10, 2017 Mar. 09, 2018 (EUT) LISN ROHDE & SCHWARZ ESH3-Z5 100311 Jul. 28, 2016 Jul. 27, 2017 (Peripheral) Software BV ADT_Cond_ NA NA NA ADT V7.3.7.3 Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Shielded Room 1. 3. The VCCI Site Registration No. is C-2040. 4.2.3 Test Procedures a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 ohm/50 uH of coupling impedance for the measuring instrument. b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. c. The frequency range from 150 kHz to 30 MHz was searched. Emission levels under (Limit – 20 dB) was not recorded. Note: All modes of operation were investigated and the worst-case emissions are reported. 4.2.4 Deviation from Test Standard No deviation. Report No.: RF170428C03-1 Page No. 20 / 33 Report Format Version: 6.1.1

ooocc 4.2.5 TEST SETUP Vertical Ground Reference Plane /Test Receiver EUT M 5ooo E___ c 6 o o | | 80cm | | L1 L1 \ N Ho T rizontal Ground Refere Plane nce Note: 1.Suppo units were connect t s L rt ed o econd ISN. 2.Both of LISNs (AMN) are 80 cm from EUT and at least 80 from other units and other metal planes 4.2.6 EUT Operating Conditions a. Placed the EUT on the testing table. b. Set the EUT under transmission condition continuously at specific channel frequency. Report No.: RF170428C03—1 Page No. 21 / 33 Report Format Version: 6.1.1

ommert [vexiras)] 4.2.7 Test Results Detector Function & Quasi—Peak (QP) / Frequency Range 150kHz ~ 30MHz g:iglwultm Average (AV), 9kHz Input Power 120Vac, 60Hz Eg‘r’]';‘i’fi”omnima' 25°C, 65%RH Tested by Getaz Yang Test Date 2017/5/23 Phase Of Power : Line (L) Frequency |Correction| Reading Value Emission Level Limit Margin No Factor (dBuV) (dBuV) (dBuV) (dB) (MHz) (dB) Q.P. AV. QP. LVA Q.P. AV. QP. AV. 1 0.15800 10.35 23.91 10.76 34.26 21.11 65.57 55.57 —31.31 —34.46 2 0.17801 10.36 22.38 9.34 82.74 19.70 64.58 54.58 —31.84 —34.88 3 0.51000 10.40 6.45 —2.26 16.85 8.14 56.00 46.00 —39.15 —37.86 4 0.69400 10.40 19.00 7.91 2940 18.31 56.00 46.00 —26.60 —27.69 5 9.04600 10.79 6.68 —1.30 17.47 9.49 60.00 50.00 —42.53 —40.51 6 12.59000 10.96 243 —8.24 13.39 7.72 60.00 50.00 —46.61 —42.28 Remarks: 1. Q.P. and AV. are abbreviations of quasi—peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level — Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value #f8 & 8 d 8 60B 8 B s a9 1ho sale & mie Report No.: RF170428C03—1 Page No. 22 / 33 Report Format Version: 6.1.1

ommert [vexiras)] Detectolr Function & Quasi—Peak (QP) / Frequency Range 150kHz ~ 30MHz g:iglwultm Average (AV), OkHz Input Power 120Vac, 60Hz Eg‘r’]'é‘i’fi”omnima' 25°C, 65%RH Tested by Getaz Yang Test Date 2017/5/23 Phase Of Power : Neutral (N) Frequency |Correction| Reading Value Emission Level Limit Margin No Factor (dBuV) (dBuV) (dBuV) (dB) (MHz) (dB) a.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.19400 10.14 15.59 3.74 25.73 13.88 63.86 53.86 —38.13 —39.98 2 0.68200 10.16 21.95 13.52 32.11 23.68 56.00 46.00 —23.89 —22.32 3 1.22138 10.18 15.01 5.39 25.19 15.57 56.00 46.00 —30.81 —30.43 4 1.75800 10.22 13.64 5.27 23.86 1549 56.00 46.00 —32.14 —30.51 5 4.37400 10.35 12.63 5.19 22.98 15.54 56.00 46.00 —33.02 —30.46 6 8.07400 10.48 13.73 8.05 24.21 18.53 60.00 50.00 —35.79 —31.47 Remarks: 1. Q.P. and AV. are abbreviations of quasi—peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level — Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value io Trace _ ar timit |.=— Cay Limit |.o— Report No.: RF170428C03—1 Page No. 23 / 33 Report Format Version: 6.1.1

4.3 6 dB Bandwidth Measurement 4.3.1 Limits of 6 dB Bandwidth Measurement The minimum of 6 dB Bandwidth Measurement is 0.5 MHz. 4.3.2 Test Setup EUT SPECTRUM ANALYZER 10 dB ATTENUATION PAD 4.3.3 Test Instruments Refer to section 4.1.2 to get information of above instrument. 4.3.4 Test Procedure a. Set resolution bandwidth (RBW) = 100 kHz b. Set the video bandwidth (VBW) ≥ 3 x RBW, Detector = Peak. c. Trace mode = max hold. d. Sweep = auto couple. e. Measure the maximum width of the emission that is constrained by the frequencies associated with the two amplitude points (upper and lower) that are attenuated by 6 dB relative to the maximum level measured in the fundamental emission 4.3.5 Deviation fromTest Standard No deviation. 4.3.6 EUT Operating Conditions The software provided by client to enable the EUT under transmission condition continuously at lowest, middle and highest channel frequencies individually. Report No.: RF170428C03-1 Page No. 24 / 33 Report Format Version: 6.1.1

4.3.7 Test Result 6 dB Bandwidth Minimum Limit Channel Frequency (MHz) Pass / Fail (MHz) (MHz) 0 2402 0.70 0.5 Pass 19 2440 0.70 0.5 Pass 39 2480 0.70 0.5 Pass Spectrum Plot of Worst Value Report No.: RF170428C03-1 Page No. 25 / 33 Report Format Version: 6.1.1

4.4 Conducted Output Power Measurement 4.4.1 Limits of Conducted Output Power Measurement For systems using digital modulation in the 2400–2483.5 MHz bands: 1 Watt (30 dBm) 4.4.2 Test Setup EUT Power Sensor Power Meter ATTENUATION PAD 4.4.3 Test Instruments Refer to section 4.1.2 to get information of above instrument. 4.4.4 Test Procedures A peak / average power sensor was used on the output port of the EUT. A power meter was used to read the response of the peak / average power sensor. Record the power level. 4.4.5 Deviation from Test Standard No deviation. 4.4.6 EUT Operating Conditions The software provided by client to enable the EUT under transmission condition continuously at lowest, middle and highest channel frequencies individually. 4.4.7 Test Results Frequency Peak Power Peak Power Limit Channel Pass / Fail (MHz) (mW) (dBm) (dBm) 0 2402 0.9795 -0.09 30 Pass 19 2440 1.236 0.92 30 Pass 39 2480 1.119 0.49 30 Pass Report No.: RF170428C03-1 Page No. 26 / 33 Report Format Version: 6.1.1

4.5 Power Spectral Density Measurement 4.5.1 Limits of Power Spectral Density Measurement The Maximum of Power Spectral Density Measurement is 8 dBm. 4.5.2 Test Setup EUT SPECTRUM 10dB ATTENUATION ANALYZER PAD 4.5.3 Test Instruments Refer to section 4.1.2 to get information of above instrument. 4.5.4 Test Procedure a. Set the RBW = 3 kHz, VBW =10 kHz, Detector = peak. b. Sweep time = auto couple, Trace mode = max hold, allow trace to fully stabilize. c. Use the peak marker function to determine the maximum power level in any 100 kHz band segment within the fundamental EBW. 4.5.5 Deviation from Test Standard No deviation. 4.5.6 EUT Operating Condition The software provided by client to enable the EUT under transmission condition continuously at lowest, middle and highest channel frequencies individually. Report No.: RF170428C03-1 Page No. 27 / 33 Report Format Version: 6.1.1

4.5.7 Test Results Frequency PSD Limit Channel Pass / Fail (MHz) (dBm/3 kHz) (dBm/3 kHz) 0 2402 -14.82 8 Pass 19 2440 -13.63 8 Pass 39 2480 -14.15 8 Pass Spectrum Plot of Worst Value Report No.: RF170428C03-1 Page No. 28 / 33 Report Format Version: 6.1.1

4.6 Conducted Out of Band Emission Measurement 4.6.1 Limits of Conducted Out of Band Emission Measurement Below –20 dB of the highest emission level of operating band (in 100 kHz Resolution Bandwidth). 4.6.2 Test Setup EUT SPECTRUM 10dB ATTENUATION ANALYZER PAD 4.6.3 Test Instruments Refer to section 4.1.2 to get information of above instrument. 4.6.4 Test Procedure MEASUREMENT PROCEDURE REF 1. Set the RBW = 100 kHz. 2. Set the VBW ≥ 300 kHz. 3. Detector = peak. 4. Sweep time = auto couple. 5. Trace mode = max hold. 6. Allow trace to fully stabilize. 7. Use the peak marker function to determine the maximum power level in any 100 kHz band segment within the fundamental EBW. MEASUREMENT PROCEDURE OOBE 1. Set RBW = 100 kHz. 2. Set VBW ≥ 300 kHz. 3. Detector = peak. 4. Sweep = auto couple. 5. Trace Mode = max hold. 6. Allow trace to fully stabilize. 7. Use the peak marker function to determine the maximum amplitude level. 4.6.5 Deviation from Test Standard No deviation. 4.6.6 EUT Operating Condition The software provided by client to enable the EUT under transmission condition continuously at lowest, middle and highest channel frequencies individually. Report No.: RF170428C03-1 Page No. 29 / 33 Report Format Version: 6.1.1

4.6.7 TEST RESULTS Ch 0 Ch 19 Ch 39 Report No.: RF170428C03-1 Page No. 30 / 33 Report Format Version: 6.1.1

Ch 0 Band Edge Ch 39 Band Edge Report No.: RF170428C03-1 Page No. 31 / 33 Report Format Version: 6.1.1

5 Pictures of Test Arrangements Please refer to the attached file (Test Setup Photo). Report No.: RF170428C03-1 Page No. 32 / 33 Report Format Version: 6.1.1

Appendix – Information on the Testing Laboratories We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited and approved according to ISO/IEC 17025. If you have any comments, please feel free to contact us at the following: Linko EMC/RF Lab Hsin Chu EMC/RF/Telecom Lab Tel: 886-2-26052180 Tel: 886-3-6668565 Fax: 886-2-26051924 Fax: 886-3-6668323 Hwa Ya EMC/RF/Safety Tel: 886-3-3183232 Fax: 886-3-3270892 Email: service.adt@tw.bureauveritas.com Web Site: www.bureauveritas-adt.com The address and road map of all our labs can be found in our web site also. --- END --- Report No.: RF170428C03-1 Page No. 33 / 33 Report Format Version: 6.1.1


Document Created: 2017-06-05 15:45:34
Document Modified: 2017-06-05 15:45:34
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC