User Manual

FCC ID: MG3-4450

Users Manual

Download: PDF
FCCID_2923746

Security Keypad Quick Start Guide XFINITY HOME SECURITY • CONTROL • ENERGY Device Overview Battery Compartment Pairing/Tamper Button Low Battery Network Indicator Status LED/Proximity Sensor Getting Started Powering Up and Pairing 1. Remove the keypad and keypad battery door 3. The keypad should start the joining process from box. (Important: The battery door must automatically. When the keypad is not joined be mounted to wall before you snap keypad to to a network, the network indicator will be off. battery door) Once it is joined, the network icon will become 2. Set your touch screen to pairing mode and then solid anytime that the keypad is awake. pull the “Remove to Pair” tab to put device into Once the keypad has successfully joined the pairing mode. network, the pairing LED will turn solid, the network indicator will turn on, and the touch screen should indicate that it has paired with the keypad.

Mounting Arming Mount the keypad battery door to the wall in the Arm Stay Button desired location using the included mounting screws Press this button and enter your 4 digit and anchors. Align the keypad to battery door and security code to arm in stay mode. snap keypad onto battery door. (XFINITY® HOME technicians MUST use screws to install keypad). Arm Away Button Status Press this button and enter your 4 digit security code to arm in away mode. There is one system status LED located at the bottom of the Security Keypad. Different colors represent the Arm Night Button following system status: Press this button and enter your 4 digit Green: Ready/Not Armed Red: Armed security code to arm in night mode. Orange: Not Ready Replacing Batteries Controls 1. View battery level indicator to determine if batteries Function Buttons need replacement. Battery level indicator will display A Button: Reserved for future use when batteries have less than 60 days of use B Button: Reserved for future use remaining. 2. Pull keypad away from wall to remove from battery Volume Control door. There are 5 possible volume levels. To increase the 3. Remove the old batteries then install AA Lithium volume, press and hold the #2 button. To decrease the batteries. volume, press and hold the #5 button. As the volume a. Lithium batteries which came with device are not raises or lowers, there will be an audible beep signifying rechargeable. that the volume has changed. Continuing to hold the 4. Align the keypad to battery door and snap keypad #2 or #5 button down will continue to raise or lower the onto battery door. volume. Proximity Detection Weekly Testing The keypad is able to detect the user’s presence within To ensure that your system continues to functioning 6 inches. Once detected the keypad will awake and as intended, you must test your system weekly. illuminate. Please contact your security monitoring company for (Lithium batteries do not charge) instructions on how to test your system. Approvals installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by This device complies with Part 15 of the FCC rules. Operation turning the equipment off and on, the user is encouraged to is subject to the following two conditions: try to correct the interference by one or more of the following (1) This device may not cause harmful interference and measures: • Reorient or relocate the receiving antenna. (2) This device must accept any interference received, including interference that may cause undesired operation. • Increase the separation between the equipment and receiver. This equipment has been tested and found to comply with • Connect the equipment into an outlet or a circuit different the limits for a class B digital device, pursuant to part 15 from that to which the receiver is connected. of the FCC Rules. These limits are designed to provide a Consult the dealer or an experienced radio/TV technician for reasonable protection against harmful interference in a help. residential installation. This equipment generates, uses, and The user is cautioned that changes and modifications made to can radiated radio frequency energy and if not installed and the equipment without approval of manufacturer could void the used in accordance with the instructions, may cause harmful users authority to operate this equipment. interference to radio communications. However, there is no guarantee that interference will not occur in a particular Change to Conforms to UL STDS 1023 & 1610


Document Created: 2015-10-13 16:40:26
Document Modified: 2015-10-13 16:40:26
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC