Modular Approval Letter

FCC ID: MCQ-S6BSM

Cover Letter(s)

Download: PDF
FCCID_1866586

)Dign Digi International 11001 Bren Road East Minnetonka, MN 55343 952—912—3444 tel 952—912—4991 central fax Modular Approval Request Applicant: Digi International Inc. FCC ID: MCQ—S6BSM 4 December 2012 To Whom It May Concern: Pursuant to Section 15.212(a)(1) of the FCC rules, the Applicant hereby requests for modular approval, compliance with the requirements are addressed below. Modular Approval Requirements Justification (i) The radio elements of the modular transmitter must have their The modular transmitter has its own RF shielding. own shielding. The physical crystal and tuning capacitors may be located external to the shielded radio elements. (ii) The modular transmitter must have buffered modulation/data The modular transmitter has buffered inputs (if such inputs are provided) to ensure that the module will modulation/data inputs. comply with part 15 requirements under conditions of excessive data rates or over—modulation. (iii) The modular transmitter must have its own power supply The modular transmitter has its own power supply regulation. regulation. (iv) The modular transmitter must comply with the antenna and The modular transmitter complies with 15.203, transmission system requirements of §§ 15.203, 15.204(b) and 15.204(b), and 15.204(c). The module either 15.204(c). The antenna must either be permanently attached or employs a unique (RPSMA or U.FL) coupler for employ a ‘"unique‘‘ antenna coupler (at all connections between the approved antennas, or the antenna is permanently module and the antenna, including the cable). The "professional attached. installation‘‘ provision of § 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) ofthis section. (v) The modular transmitter must be tested in a stand—alone The modular transmitter was tested in a stand— configuration, i.e., the module must not be inside another device alone configuration. during testing for compliance with part 15 requirements. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in § 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see § 15.27(a)). The length of these lines shall be the length typical of actual use or,if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available (see § 15.31()). (vi) The modular transmitter must be equipped with either a The modular transmitter has a permanently affixed permanently affixed label or must be capable of electronically label that includes the FCC ID number. The user

)Dign Digi International 11001 Bren Road East Minnetonka, MN 55343 952—912—3444 tel 952—912—4991 central fax displaying its FCC identification number. manual includes instructions for exterior labeling when the modular transmitter is installed inside (A) If using a permanently affixed label, the modular transmitter another device must be labeled with its own FCC identification number, and, ifthe FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID: XYZMODEL1® or ‘"Contains FCC ID: XYZMODEL1.* Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. (B) If the modular transmitter uses an electronic display of the FCC identification number, the information must be readily accessible and visible on the modular transmitter or on the device in which it is installed. If the module is installed inside another device, then the outside of the device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as the following: ‘"Contains FCC certified transmitter module(s)."" Any similar wording that expresses the same meaning may be used. The user manual must include instructions on how to access the electronic display. A copy of these instructions must be included in the application for equipment authorization. (vii) The modular transmitter must comply with any specific rules The user manual for the modular transmitter or operating requirements that ordinarily apply to a complete provides adequate instructions for usage, approved transmitter and the manufacturer must provide adequate antennas, and power supply requirements. instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. (viii) The modular transmitter must comply with any applicable RF The modular transmitter was tested and complies exposure requirements in its final configuration. with applicable RF exposure requirements. Sincerely, — Paul Dahl Hardware Manager


Document Created: 2019-09-23 19:29:46
Document Modified: 2019-09-23 19:29:46
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC