DFS Report

FCC ID: MAU023

Test Report

Download: PDF
FCCID_785915

DFS TEST REPORT REPORT NO.: RF960202L09 MODEL NO.: V100 RECEIVED: Feb. 02, 2007 TESTED: Feb. 06 ~ 12, 2007 ISSUED: Feb. 13, 2007 APPLICANT: MITAC TECHNOLOGY CORPORATION ADDRESS: 4F, No. 1, R&D Road 2, Hsinchu Science-Based Industrial Park, Hsinchu 300, Taiwan, R.O.C. ISSUED BY: Advance Data Technology Corporation LAB ADDRESS: No. 47, 14th Ling, Chia Pau Tsuen, Lin Kou Hsiang 244, Taipei Hsien, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd., Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 18 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA, A2LA or any government agencies. The test results in the report only apply to the tested sample. Report No.: RF960202L09 1 Report Format Version 2.0.5

Table of Contents 1. CERTIFICATION ......................................................................................................3 2. GENERAL INFORMATION.......................................................................................4 2.1 GENERAL DESCRIPTION OF EUT.........................................................................4 2.2 DESCRIPTION OF TEST MODES...........................................................................4 3. TEST RESULTS .......................................................................................................5 2.3 DYNAMIC FREQUENCY SELECTION ....................................................................5 2.3.1 OPERATING FREQUENCY OF U-NII DEVICE .......................................................6 2.3.2 TEST LIMITS AND RADAR SIGNAL PARAMETERS ..............................................6 2.3.3 TEST INSTRUMENTS .............................................................................................9 2.3.4 DESCRIPTION OF SUPPORT UNITS .....................................................................9 2.3.5 SOFTWARE AND FIRMWARE.................................................................................9 2.3.6 DESCRIPTION OF AVAILABLE ANTENNAS ...........................................................9 2.3.7 MAXIMUM AND MINIMUM CONDUCTED POWER ..............................................10 2.3.8 MAXIMUM AND MINIMUM E.I.R.P. POWER .........................................................10 2.3.9 TEST PROCEDURE .............................................................................................. 11 2.3.10 DEVIATION FROM TEST STANDARD ..................................................................13 2.3.11 CONDUCTED TEST SETUP CONFIGURATION...................................................13 2.3.12 LIST OF MEASUREMENTS...................................................................................14 2.3.13 TEST RESULTS .....................................................................................................15 3. INFORMATION ON THE TESTING LABORATORIES ...........................................18 Report No.: RF960202L09 2 Report Format Version 2.0.5

1. CERTIFICATION PRODUCT: Notebook Personal Computer MODEL: V100 BRAND: MITAC APPLICANT: MITAC TECHNOLOGY CORPORATION TEST SAMPLE: ENGINEERING SAMPLE TESTED: Feb. 06 ~ 12, 2007 STANDARDS: FCC Part 15, Subpart E (Section 15.407) FCC 06-96 The above equipment (model: V100) has been tested by Advance Data Technology Corporation, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE: Feb. 13, 2007 Rennie Wang TECHNICAL ACCEPTANCE : , DATE: Feb. 13, 2007 Responsible for RF Dylan Chiou APPROVED BY : , DATE: Feb. 13, 2007 Gary Chang / Supervisor Report No.: RF960202L09 3 Report Format Version 2.0.5

2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT EUT Notebook Personal Computer MODEL NO. V100 POWER SUPPLY 16Vdc from adapter MODULATION TYPE 64QAM, 16QAM, QPSK, BPSK MODULATION TECHNOLOGY OFDM TRANSFER RATE 54/48/36/24/18/12/9/6Mbps FREQUENCY RANGE 5.250 ~ 5.350GHz NUMBER OF CHANNEL 4 CHANNEL SPACING 20MHz OUTPUT POWER 12.19mW PIFA with 2.45dBi gain for right antenna ANTENNA TYPE PIFA with 3.97dBi gain for left antenna DATA CABLE NA I/O PORTS Refer to user’s manual ASSOCIATED DEVICES Adapter NOTE: 1. The EUT was operated by the following adapter: Brand: FAIRWAY Model: VAN40A-16A Input: 100-240Vac, 50-60Hz, 1.0A max Output: 16Vdc, 2.5A, 40W max AC 1.8m shielded cable without core Power Line: DC 1.6m shielded cable with one core 2. The EUT operates in the 5GHz Band and compatibility with 802.11a technology. 3. The above EUT information was declared by the manufacturer and for more detailed features description, please refer to the manufacturer's specifications or User's Manual. 2.2 DESCRIPTION OF TEST MODES 4 channels are provided to this EUT. CHANNEL FREQUENCY 1 5260 MHz 2 5280 MHz 3 5300 MHz 4 5320 MHz Report No.: RF960202L09 4 Report Format Version 2.0.5

3. TEST RESULTS 2.3 DYNAMIC FREQUENCY SELECTION The manufacturer shall state whether the UUT is capable of operating as a Master and/or a Client. If the UUT is capable of operating in more than one operating mode then each operating mode shall be tested separately. See tables 1 and 2 for the applicability of DFS requirements for each of the operational modes. Table 1: Applicability of DFS requirements prior to use a channel Operational Mode Requirement Client without Client with radar Master radar detection detection Non-Occupancy Period 9 Not required 9 DFS Detection Threshold 9 Not required 9 Channel Availability Check Time 9 Not required Not required Uniform Spreading 9 Not required Not required U-NII Detection Bandwidth 9 Not required 9 Table 2: Applicability of DFS requirements during normal operation. Operational Mode Requirement Client without Client with radar Master radar detection detection DFS Detection Threshold 9 Not required 9 Channel Closing Transmission 9 9 9 Time Channel Move Time 9 9 9 U-NII Detection Bandwidth 9 Not required 9 Report No.: RF960202L09 5 Report Format Version 2.0.5

2.3.1 OPERATING FREQUENCY OF U-NII DEVICE Table 3: Operating frequency range of UUT. Operating Frequency Range Operational Mode 5250~5350MHz 5470~5725MHz Master Not Apply Not Apply Client without radar detection 9 Not Apply Client with radar detection Not Apply Not Apply 2.3.2 TEST LIMITS AND RADAR SIGNAL PARAMETERS DETECTION THRESHOLD VALUES Table 4: DFS Detection Thresholds for Master Devices and Client Devices With Radar Detection. Value Maximum Transmit Power (See Notes 1 and 2) ≥ 200 milliwatt -64 dBm < 200 milliwatt -62 dBm Note 1: This is the level at the input of the receiver assuming a 0 dBi receive antenna. Note 2: Throughout these test procedures an additional 1 dB has been added to the amplitude of the test transmission waveforms to account for variations in measurement equipment. This will ensure that the test signal is at or above the detection threshold level to trigger a DFS response. Report No.: RF960202L09 6 Report Format Version 2.0.5

Table 5: DFS Response Requirement Values Parameter Value Non-occupancy period Minimum 30 minutes Channel Availability Check Time 60 seconds Channel Move Time 10 seconds See Note 1. Channel Closing Transmission Time 200 milliseconds + an aggregate of 60 milliseconds over remaining 10 second period. See Notes 1 and 2. U-NII Detection Bandwidth Minimum 80% of the UNII 99% transmission power bandwidth. See Note 3. Note 1: The instant that the Channel Move Time and the Channel Closing Transmission Time begins is as follows: • For the Short Pulse Radar Test Signals this instant is the end of the Burst. • For the Frequency Hopping radar Test Signal, this instant is the end of the last radar Burst generated. • For the Long Pulse Radar Test Signal this instant is the end of the 12 second period defining the Radar Waveform. Note 2: The Channel Closing Transmission Time is comprised of 200 milliseconds starting at the beginning of the Channel Move Time plus any additional intermittent control signals required to facilitate a Channel move (an aggregate of 60 milliseconds) during the remainder of the 10 second period. The aggregate duration of control signals will not count quiet periods in between transmissions. Note 3: During the U-NII Detection Bandwidth detection test, radar type 1 is used and for each frequency step the minimum percentage of detection is 90 percent. Measurements are performed with no data traffic. Report No.: RF960202L09 7 Report Format Version 2.0.5

PARAMETERS OF DFS TEST SIGNALS Step intervals of 0.1 microsecond for Pulse Width, 1 microsecond for PRI, 1 MHz for chirp width and 1 for the number of pulses will be utilized for the random determination of specific test waveforms. Table 6: Short Pulse Radar Test Waveforms. Minimum Percentage Minimum Pulse Width PRI Number Radar Type of Number of (µsec) (µsec) of Pulses Successful Trials Detection 1 1 1428 18 60% 30 2 1-5 150-230 23-29 60% 30 3 6-10 200-500 16-18 60% 30 4 11-20 200-500 12-16 60% 30 Aggregate (Radar Types 1-4) 80% 120 Table 7: Long Pulse Radar Test Waveform Minimum Pulse Chirp Number Minimum Radar PRI Number Percentage of Width Width of Pulses Number of Type (µsec) of Bursts Successful (µsec) (MHz) per Burst Trials Detection 1000-200 5 50-100 5-20 1-3 8-20 80% 30 0 Table 8: Frequency Hopping Radar Test Waveform Hopping Minimum Pulse Pulses Hopping Minimum Radar PRI Sequence Percentage of Width per Rate Number of Type (µsec) Length Successful (µsec) Hop (kHz) Trials (msec) Detection 6 1 333 9 0.333 300 70% 30 Report No.: RF960202L09 8 Report Format Version 2.0.5

2.3.3 TEST INSTRUMENTS Table 9: Test instruments list. DESCRIPTION & CALIBRATED MODEL NO. BRAND MANUFACTURER UNTIL R&S Spectrum analyzer FSP40 R&S Apr. 09, 2007 Signal generator 8645A Agilent May. 24, 2007 Oscilloscope TDS 5104 Tektronix Aug. 28. 2007 2.3.4 DESCRIPTION OF SUPPORT UNITS Table 10: Support Unit information. No. Product Brand Model No. ID 1 802.11a/b/g Access Point Cisco AIR-AP1242AG-A-K9 LDK102056 2.3.5 SOFTWARE AND FIRMWARE Table 11: The software/firmware version for U-NII device. No. Product Model No. Software/Firmware Version 1 802.11a/b/g Access Point AIR-AP1242AG-A-K9 C1240-K9W7-TAR.123-11.JA 2 Host equipment V100 Intel ver 10.1.1.3 2.3.6 DESCRIPTION OF AVAILABLE ANTENNAS Table 12: Antenna list. Max. Antenna Type Operation Frequency Range Gain(dBi) Right PIFA 5.1 ~ 5.9 GHz 2.45 Left PIFA 5.1 ~ 5.9 GHz 3.97 Report No.: RF960202L09 9 Report Format Version 2.0.5

2.3.7 MAXIMUM AND MINIMUM CONDUCTED POWER Table 13: The measured conducted output power. MAX. Power MIN. Power Frequency Band(MHZ) Output Output Output Output Power(dBm) Power(mW) Power(dBm) Power(mW) 5250~5350MHz 10.86 12.19 5 3.162 2.3.8 MAXIMUM AND MINIMUM E.I.R.P. POWER Table 14: The E.I.R.P output power list. MAX. Power MIN. Power Frequency Band(MHZ) Output Output Output Output Power(dBm) Power(mW) Power(dBm) Power(mW) 5250~5350MHz 14.83 30.41 8.97 7.889 Report No.: RF960202L09 10 Report Format Version 2.0.5

2.3.9 TEST PROCEDURE ADT DFS Measurement System: A complete ADT DFS Measurement System consists of two subsystems: (1) the Radar Signal Generating Subsystem and (2) the Traffic Monitoring Subsystem. The control PC is necessary for generating the Radar waveforms in Table 6, 7 and 8. The traffic monitoring subsystem is specified to the type of unit under test (UUT). Conducted setup configuration of ADT DFS Measurement System Control PC Radar Signal Generating Subsystem Spectrum Oscilloscope Analyzer Attenuator C/S Attenuator Attenuator C/S Traffic Monitoring Subsystem Client (UUT) Master The test transmission will always be from the Master Device to the Client Device. While the Client device is set up to associate with the Master device and play the MPEG file (6  Magic Hours) from Master device, the designated MPEG test file and instructions are located at: http://ntiacsd.ntia.doc.gov/dfs/. Report No.: RF960202L09 11 Report Format Version 2.0.5

Calibration of DFS Detection Threshold Level: The measured channel is 5320MHz. The radar signal was the same as transmitted channels, and injected into the antenna port of AP (master), measured the channel closing transmission time and channel move time. The Required detection threshold is -58dBm (= -62 +1+3)dBm. The calibrated conducted detection threshold level is set to -59dBm. The tested level is lower than required level hence it provides margin to the limit. Conducted setup configuration of Calibration of DFS Detection Threshold Level Control PC Spectrum Oscilloscope Radar Signal Generating Analyzer Subsystem 50Ω Load (Terminator) Attenuator C/S 50Ω Load Attenuator Attenuator C/S (Terminator) Master Report No.: RF960202L09 12 Report Format Version 2.0.5

2.3.10 DEVIATION FROM TEST STANDARD No deviation. 2.3.11 CONDUCTED TEST SETUP CONFIGURATION Control PC Spectrum Oscilloscope Radar Signal Generating Analyzer Subsystem Attenuator C/S Attenuator Attenuator C/S Master Client (UUT) Notebook The UUT is a U-NII Device operating in Client mode without Radar Detection function. The radar test signals are injected into the Master Device. Report No.: RF960202L09 13 Report Format Version 2.0.5

2.3.12 LIST OF MEASUREMENTS The UUT (V100) is capable of operating as a Client (without radar detection). Clause Test Parameter Remarks Pass/Fail 15.407 Channel Availability Check Time Not Required NA 15.407 In-Service Monitoring Not Required NA 15.407 Channel Move Time Applicable Pass 15.407 Channel Closing Transmission Time Applicable Pass 15.407 Non- Occupancy Period Not Required NA 15.407 Uniform Spreading Not Required NA Report No.: RF960202L09 14 Report Format Version 2.0.5

2.3.13 TEST RESULTS DETECTION THRESHOLD VALUES INJECTED INTO AP The Required detection threshold is -58dBm (= -62 +1+3)dBm. The Radar Burst signal level to the AP connector is–59dBm. The tested level is lower than required level hence it provides margin to the limit. RBW 3 MHz Marker 1 [T1 ] VBW 10 MHz -59.41 dBm Ref -20 dBm * Att 0 dB SWT 20 s 14.160000 s -20 A -30 1 AP VIEW -40 -50 Radar signal 1 -60 -70 -80 -90 -100 -110 -120 Center 5.32 GHz 2 s/ Noise Floor 2nd comment ... Date: 10.JAN.2007 12:15:19 Radar Signal 1 Report No.: RF960202L09 15 Report Format Version 2.0.5

Channel Closing Transmission and Channel Move Time Radar Signal Traffic Signal Noise Floor Radar Signal Noise Floor Traffic Signal Radar signal 1 NOTE: T1 denotes the start of Channel Move Time upon the end of the last Radar burst. T2 denotes the data transmission time of 200ms from T1. T3 denotes the 10 second from T1 to observe the aggregate duration of transmissions. Report No.: RF960202L09 16 Report Format Version 2.0.5

Type 1 Radar Statistical Performances Trial # Pulses per Burst Pulse Width (s) PRI (s) Detection 1 18 1.0u 1.428m No 2 18 1.0u 1.428m Yes 3 18 1.0u 1.428m Yes 4 18 1.0u 1.428m Yes 5 18 1.0u 1.428m Yes 6 18 1.0u 1.428m Yes 7 18 1.0u 1.428m No 8 18 1.0u 1.428m Yes 9 18 1.0u 1.428m Yes 10 18 1.0u 1.428m Yes 11 18 1.0u 1.428m Yes 12 18 1.0u 1.428m Yes 13 18 1.0u 1.428m Yes 14 18 1.0u 1.428m Yes 15 18 1.0u 1.428m Yes 16 18 1.0u 1.428m Yes 17 18 1.0u 1.428m No 18 18 1.0u 1.428m Yes 19 18 1.0u 1.428m Yes 20 18 1.0u 1.428m Yes 21 18 1.0u 1.428m Yes 22 18 1.0u 1.428m Yes 23 18 1.0u 1.428m Yes 24 18 1.0u 1.428m Yes 25 18 1.0u 1.428m No 26 18 1.0u 1.428m Yes 27 18 1.0u 1.428m Yes 28 18 1.0u 1.428m Yes 29 18 1.0u 1.428m Yes 30 18 1.0u 1.428m Yes Detection Rate: 86.7 % Report No.: RF960202L09 17 Report Format Version 2.0.5

3. INFORMATION ON THE TESTING LABORATORIES We, ADT Corp., were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited and approved by the following approval agencies according to ISO/IEC 17025. USA FCC, UL, A2LA Germany TUV Rheinland Japan VCCI Norway NEMKO Canada INDUSTRY CANADA , CSA R.O.C. CNLA, BSMI, NCC Netherlands Telefication Singapore PSB , GOST-ASIA(MOU) Russia CERTIS(MOU) Copies of accreditation certificates of our laboratories obtained from approval agencies can be downloaded from our web site: www.adt.com.tw/index.5/phtml. If you have any comments, please feel free to contact us at the following: Linko EMC/RF Lab: Hsin Chu EMC/RF Lab: Tel: 886-2-26052180 Tel: 886-3-5935343 Fax: 886-2-26051924 Fax: 886-3-5935342 Hwa Ya EMC/RF/Safety Telecom Lab: Tel: 886-3-3183232 Fax: 886-3-3185050 Web Site: www.adt.com.tw The address and road map of all our labs can be found in our web site also. Report No.: RF960202L09 18 Report Format Version 2.0.5


Document Created: 2007-03-29 15:44:07
Document Modified: 2007-03-29 15:44:07
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC