SAR Report Appendix E Probe 5200 Body

FCC ID: MAU023

RF Exposure Info

Download: PDF
FCCID_785890

NCL CALIBRATION LABORATORIES Calibration File No.: CP—701 Client.: Wistron CERTIFICATE OF CALIBRATION It is certified that the equipmentidentified below has been calibrated in the NCL CALIBRATION LABORATORIES by qualified personnel following recognized procedures and using transfer standards traceable to NRC/NIST. Equipment: Miniature Isotropic RF Probe 5200 MHz BODY Calibration Manufacturer: APREL Laboratories Model No.: E—020 Serial No.: 266 Calibration Procedure: SSUDRB—TP—D01—032—E020—V2 Project No: QTKB—ALS—E020—CAL—5238 Calibrated: 20" June 2006 Released on: 22"" June 2006 APREL Laboratories Certified Under Laboratory 48 of SCC This Calibration Certificate is Accompanied with the Calibration Results Summary Released By: 1 TT 51 SPECTRUM WaAY Division of APREL Lab. NEPEAN, ONTARIO TEL: (613) 820—4088 CANADA K2R 126 FAX:(613) 820—4161

NCL Calibration Laboratories Division of APREL Laboratories. Introduction This Calibration Report reproduces the results of the calibration performed in line with the SSIU/DRB—TP—D01—032—E020—V2 E—Field Probe Calibration Procedure. The results contained within this report are for APREL E—Field Probe E—020 266. References SSUVDRB—TP—D01—032—E020—V2 E—Field Probe Calibration Procedure IEEE 1528 "Recommended Practice for Determining the Peak Spatial—Average Specific Absorption Rate (SAR) in the Human Body Due to Wireless Communications Devices: Experimental Techniques" SSI—TP—011 Tissue Calibration Procedure IEC 62209 "Human exposure to radio frequency fields from hand—held and body— mounted wireless communication devices — Human models, instrumentation, and procedures —Part 1 & 2: Procedure to determine the Specific Absorption Rate (SAR) for hand—held devices used in close proximity of the ear (frequency range of 300 MHz to 3 GHz)" IEEE 1309 Draft Standard for Calibration of Electromagnetic Field Sensors and Probes, Excluding Antennas, from 9kHz to 40GHz Conditions Probe 266 was a re—calibration. Ambient Temperature of the Laboratory: 22 °C +/— 0.5°C Temperature of the Tissue: 21 °C +/— 0.5°C We the undersigned attest that to the best of our knowledge the calibration of this probe has beemaccurately conducted and that all information contained within this|report has \been reviewed for accuracy. Page 2 of 10 This page has been reviewed for content and attested to on Page 2 of this document.

NCL Calibration Laboratories Division of APREL Laboratories. Calibration Results Summary Probe Type: E—Field Probe E—020 Serial Number: 266 Frequency: 5200 MHz Sensor Offset: 1.56 mm Sensor Length: 2.5 mm Tip Enclosure: Ertalyte* Tip Diameter: <5 mm Tip Length: 60 mm Total Length: 290 mm *Resistive to recommended tissue recipes per IEEE—1528 Sensitivity in Air Channel X: 1.2 uV/(V/im)® Channel Y: 1.2 uV/(V/im) Channel Z: 1.2 uV/(V/im)® Diode Compression Point: 95 mV Page 3 of 10 This page has been reviewed for content and attested to on Page 2 ofthis document.

NCL Calibration Laboratories Division of APREL Laboratories. Sensitivity in Body Tissue Frequency: 5200 MHz Epsilon: 43.0 (+/—10%) Sigma: 5.75 S/m (+/—10%) ConvF Channel X: 4.4 Channel Y: 4.4 Channel Z: 4.4 Tissue sensitivity values were calculated using the load impedance of the APREL Laboratories Daq—Paq. Boundary Effect: Uncertainty resulting from the boundary effect is less than 2% for the distance between the tip of the probe and the tissue boundary, when less than 2.44mm. Spatial Resolution: The measured probe tip diameter is 5 mm (+/— 0.01 mm) and therefore meets the requirements of SSI/DRB—TP—D01—032 for spatial resolution. Page 4 of 10 This page has been reviewed for content and attested to on Page 2 ofthis document.

NCL Calibration Laboratories Divisio of APREL Laborionis Receiving Pattern 5200 MHz (Air) Recebing Patorn Probe sn 20e saooutte —+—om ~#—ore _> ons —+—Tat Fage Sof 10 "This page has been reviewed fr cntent and atested o on Page2 ofthis document

NCL Calibration Laboratories Division of APREL Laborstones Isotropy Error 5200 MHz (Air) novony Enor Probe in see seocute f a iij s2 | rrr i4i : > > $3 z 5> i4 ii 4 o 100 xo xo Incropy is Prote sn se sacoumc Dogrees (td) Isotropicity in Tissue: 0.10 48 Fage cof 10 "This page has beenreviewed for content and atested o on Page 2 ofhis document

NCL Calibration Laboratories Division of APREL Libortors Dynal Range Probe 2Dynanic Range um Youre pwon —e—crevoms tevnesnien PareTot 10 "This page has been reviewed for content and atested o on Page 2 ofhisdocument

NCL Calibration Laboratories Division of APREL Laboratories. Video Bandwidth Probe Frequency Characteristics Probe output level (dB) 1 10 100 1000 10000 Frequency (Hz) Video Bandwidth at 500 Hz 1 dB Video Bandwidth at 1.02 KHz: 3 dB Page 8 of 10 This page has been reviewed for content and attested to on Page 2 of this document.

NCL Calibration Laboratories Division of APREL Laboratories. Conversion Factor Uncertainty Assessment Frequency: 5200MHz Epsilon: 43.0 (+/—10%) Sigma: 5.75 S/m (+/10%) ConvF Channel X: 4.4 7%(K=2) Channel Y: 4.4 7%(K=2) Channel Z: 4.4 T%(K=2) To minimize the uncertainty calculation all tissue sensitivity values were calculated using a load impedance of 5 MGQ. Boundary Effect: For a distance of 2.4mm the evaluated uncertainty (increase in the probe sensitivity) is less than 2%. Page 9 of 10 This page has been reviewed for content and attested to on Page 2 ofthis document.

NCL Calibration Laboratories Division of APREL Laboratories. Test Equipment The test equipment used during Probe Calibration, manufacturer, model number and, current calibration status are listed and located on the main APREL server R:ANCL\Calibration Equipment\Instrument List May 2004. Page 10 of 10 This page has been reviewed for content and attested to on Page 2 ofthis document.


Document Created: 2006-10-19 11:29:18
Document Modified: 2006-10-19 11:29:18
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC