SAR Report Appendix E Probe 2450 Body

FCC ID: MAU023

RF Exposure Info

Download: PDF
FCCID_785888

NCL CALIBRATION LABORATORIES Calibration File No.: CP—699 Client.: Wistron CERTIFICATE OF CALIBRATIO N It is certified that the equipment identified below has been calibrated in the NCL CALIBRATION LABORATORIES by qualified personnel following recognized procedures and using transfer standards traceable to NRC/NIST. Equipment: Miniature Isotropic RF Probe 2450 MHz BODY Calibration Manufacturer: APREL Laboratories Model No.: E—020 Serial No.: 266 Calibration Procedure: SSVDRB—TP—D01—032—E020—V2 Project No: QTKB—ALS—E020—CAL—5238 Calibrated: 21" June 2006 Released on: 22"" June 2006 APREL Laboratories Certified Under Laboratory 48 of SCC This Calibration Certificate is Iacomplete U Accorgpanied with the Calibration Results Summary Released By: \K—4 NQL CALIBRATION LABORATORIES 51 SPECTRUM Way Division of APREL Lab. NEPEAN, ONTARIO TEL: (613) 820—4988 CANADA K2R 126 FAX: (613) 820—4161

NCL Calibration Laboratories Division of APREL Laboratories. Introduction This Calibration Report reproduces the results of the calibration performed in line with the SSU/DRB—TP—D01—032—E020—V2 E—Field Probe Calibration Procedure. The results contained within this report are for APREL E—Field Probe E—020 266. References SSI/DRB—TP—D01—032—E020—V2 E—Field Probe Calibration Procedure IEEE 1528 "Recommended Practice for Determining the Peak Spatial—Average Specific Absorption Rate (SAR) in the Human Body Due to Wireless Communications Devices: Experimental Techniques" SSI—TP—011 Tissue Calibration Procedure IEC 62209 "Human exposure to radio frequency fields from hand—held and body— mounted wireless communication devices — Human models, instrumentation, and procedures —Part 1 & 2: Procedure to determine the Specific Absorption Rate (SAR) for hand—held devices used in close proximity of the ear (frequency range of 300 MHz to 3 GHz)" IEEE 1309 Draft Standard for Calibration of Electromagnetic Field Sensors and Probes, Excluding Antennas, from 9kHz to 40GHz Conditions Probe 266 was a re—calibration. Ambient Temperature of the Laboratory: 22 °C +/— 0.5°C Temperature of the Tissue: 21 °C +/— 0.5°C We the undersigned attest that to the best of our knowledge the calibration of this probe has been accurately conducted and that all information contained w1th1@n@]n reviewed for accuracy. Stuart Nicol Page 2 of 10 This page has been reviewed for content and attested to on Page2 ofthis document.

NCL Calibration Laboratories Division of APREL Laboratories. Calibration Results Summary Probe Type: E—Field Probe E—020 Serial Number: 266 Frequency: 2450 MHz Sensor Offset: 1.56 mm Sensor Length: 2.5 mm Tip Enclosure: Ertalyte® Tip Diameter: <5 mm Tip Length: 60 mm Total Length: 290 mm *Resistive to recommended tissue recipes per IEEE—1528 Sensitivity in Air Channel X: 1.2 uV/(V/im) Channel Y: 1.2 pV/(V/im) Channel Z: 1.2 uV/(V/im)* Diode Compression Point: 95 mV Page 3 of 10 This page has been reviewed for content and attested to on Page 2 ofthis document.

NCL Calibration Laboratories Division of APREL Laboratories. Sensitivity in Body Tissue Frequency: 2450 MHz Epsilon: 52.7 (+/—5%) Sigma: 1.95 S$/m (+/—10%) ConvF Channel X: 5.02 Channel Y: 5.02 Channel Z: 5.02 Tissue sensitivity values were calculated using the load impedance of the APREL Laboratories Daq—Paq. Boundary Effect: Uncertainty resulting from the boundary effect is less than 2% for the distance between the tip of the probe and the tissue boundary, when less than 2.44mm. Spatial Resolution: The measured probe tip diameter is 5 mm (+/— 0.01 mm) and therefore meets the requirements of SSI/DRB—TP—D01—032 for spatial resolution. Page 4 of 10 This page has been reviewed for content and attested to on Page 2 of this document.

NCL Calibration Laboratories Division of APREL Laboratoris Receiving Pattern 2450 MHz (Air) Recubing Patton Probe sn se adsoutts <4— hi —#—che > ons +—Tot Fare sot 10 "This page has been reviewed for contentand atested o on Page 2 of hi document

NCL Calibration Laboratories Division of APREL Laboraons Isotropy Error 2450 MHz (Air) inovopy Enor Probe in zeeaesoute pe 461901 ern ces ve0 Enort) Inotropy Pc Protesin 2s aesoute Isotropicity Tissué 0.10 48 Fage sor 10 "This page has beenreviewed for content and atested to on Page 2 ohi document

NCL Calibration Laboratories Divison of APREL Laboratones Dyna Probe 288 Dynanic Range se e — | m | | se is us wa ues ums mas umes smme terermaminzn Fare Tor 10 "This page has beenreviewed for contentand atestd o on Page 2 of this document

NCL Calibration Laboratories Division of APREL Laboratories. Video Bandwidth Probe Frequency Characteristics Probe output level (dB) 1 I —6 M 1 1 10 100 1000 10000 Frequency (Hz) Video Bandwidth at 500 Hz 1 dB Video Bandwidth at 1.02 KHz: 3 dB Page 8 of 10 This page has been reviewed for content and attested to on Page 2 of this document.

NCL Calibration Laboratories Division of APREL Laboratories. Conversion Factor Uncertainty Assessment Sensitivity in Body Tissue Frequency: 2450 MHz Epsilon: 52.7 (+/—5%) Sigma: 1.95 S/m (+/—10%) ConvF Channel X: 5.02 7%(K=2) Channel Y: 5.02 T%(K=2) Channel 2: 5.02 T%(K=2) To minimize the uncertainty calculation all tissue sensitivity values were calculated using a load impedance of 5 MS2. Boundary Effect: For a distance of 2.5mm the evaluated uncertainty (increase in the probe sensitivity) is less than 2%. Page 9 of 10 This page has been reviewed for content and attested to on Page 2 ofthis document.

NCL Calibration Laboratories Division of APREL Laboratories. Test Equipment The test equipment used during Probe Calibration, manufacturer, mode! number and, current calibration status are listed and located on the main APREL server R:ANCL\Calibration Equipment\instrument List May 2006. Page 10 of 10 This page has been reviewed for content and attested to on Page 2 ofthis document.


Document Created: 2007-02-12 17:17:10
Document Modified: 2007-02-12 17:17:10
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC