Test Report

FCC ID: M5VC30047XA

Test Report

Download: PDF
FCCID_3096895

EMC Technologies (NZ) Ltd PO Box 68-307 Newton, Auckland 1145 New Zealand Phone 09 360 0862 Fax 09 360 0861 E-Mail Address: aucklab@ihug.co.nz Web Site: www.emctech.com.au TEST REPORT Gallagher C300480 T15 Proximity Card Reader tested to 47 Code of Federal Regulations Part 15 - Radio Frequency Devices Subpart C – Intentional Radiators Section 15.209 and Section 15.225 Operation within the band 13.110 -14.010 MHz for Gallagher Group Ltd This Test Report is issued with the authority of: ________________________________________ Andrew Cutler- General Manager ____________________________________________________________________________________________________________________________________________________________________________ Page 1 of 32 Test Report No 160108.1A 27th July 2016 This report may not be reproduced except in full.

Table of Contents 1. STATEMENT OF COMPLIANCE 3 2. RESULTS SUMMARY 3 3. INTRODUCTION 4 4. CLIENT INFORMATION 4 5. DESCRIPTION OF TEST SAMPLE 4 6. SETUPS AND PROCEDURES 5 7. TEST EQUIPMENT USED 21 8. ACCREDITATIONS 21 9. PHOTOGRAPHS 22 ____________________________________________________________________________________________________________________________________________________________________________ Page 2 of 32 Test Report No 160108.1A 27th July 2016 This report may not be reproduced except in full.

1. STATEMENT OF COMPLIANCE The Gallagher C300480 T15 Proximity Card Reader complies with FCC Part 15 Subpart C Section 15.225 as an Intentional Radiator when the methods as described in ANSI C63.4 - 2003 are applied. 2. RESULTS SUMMARY The results from testing carried out in May 2016 are summarised in the following table: Clause Parameter Result 15.201 Equipment authorisation Certification required. requirement 15.203 Antenna requirement Complies. Antennas internal to the device. 15.204 External PA and antenna Not applicable. No external devices. modifications 15.205 Restricted bands of operation Complies. Device transmits on 13.560 MHz and 125 kHz. 15.207 Conducted limits Complies. 15.209 Radiated emission limits - Complies. Emissions < 30 MHz 15.209 Radiated emission limits – Complies. Emissions > 30 MHz 15.225 Radiated emission limits - Complies. Fundamental 15.225 Frequency stability Complies ____________________________________________________________________________________________________________________________________________________________________________ Page 3 of 32 Test Report No 160108.1A 27th July 2016 This report may not be reproduced except in full.

3. INTRODUCTION This report describes the tests and measurements performed for the purpose of determining compliance with the specification. The client selected the test sample. This report relates only to the sample tested. This report contains no corrections or erasures. Measurement uncertainties with statistical confidence intervals of 95% are shown below test results. Both Class A and Class B uncertainties have been accounted for, as well as influence uncertainties where appropriate. This report replaces report number 160108.1 to address issues raised during the FCC certification process. 4. CLIENT INFORMATION Company Name Gallagher Group Ltd Address Kahikatea Drive City Hamilton Country New Zealand Contact Mr Brian Rose 5. DESCRIPTION OF TEST SAMPLE Brand Name Gallagher Model Number Tested C300480 T15 Product Proximity Card Reader Manufacturer Gallagher Group Ltd Country of Origin New Zealand Serial Number 1619507001 FCC ID M5VC30044X The model tested is a dual mode transmitter operating on 125 kHz and 13.560 MHz. ____________________________________________________________________________________________________________________________________________________________________________ Page 4 of 32 Test Report No 160108.1A 27th July 2016 This report may not be reproduced except in full.

6. SETUPS AND PROCEDURES Standard The sample was tested in accordance with 47 CFR Part 15 Subpart C. Methods and Procedures The measurement methods and procedures as described in ANSI C63.4 - 2003 were used. Section 15.201: Equipment authorisation requirement Certification as detailed in Subpart J of Part 2 is required for this device. Section 15.203: Antenna requirement This device has internal antennas for the 125 kHz and 13.560 MHz transmitters. Result: Complies. Section 15.204: External radio frequency power amplifiers and antenna modifications It is not possible to attach an external power amplifier to this transmitter. Result: Complies. ____________________________________________________________________________________________________________________________________________________________________________ Page 5 of 32 Test Report No 160108.1A 27th July 2016 This report may not be reproduced except in full.

Section 15.205: Restricted bands of operation The transmitter transmits on 125.000 kHz. This device would therefore fall between the restricted bands of 90 – 110 kHz and 495 – 505 kHz. Measurements were made using a span of 10 kHz with a resolution bandwidth of 100 Hz and a video bandwidth of 300 Hz. Measurements were made using a spectrum analyser with the 99% power points (-26 dB points) being determined. At 125 kHz the modulation bandwidth was measured to be 1175 Hz. ____________________________________________________________________________________________________________________________________________________________________________ Page 6 of 32 Test Report No 160108.1A 27th July 2016 This report may not be reproduced except in full.

The transmitter transmits on 13.560 MHz. This device would therefore fall into the band of 13.110 – 14.010 MHz that is covered by Section 15.225. Measurements were made when the device was waiting on a card and when it was reading a card. Measurements were made using a spectrum analyser with the 99% power points (-26 dB points) being determined. Measurements were made using a span of 1.0 MHz with a resolution bandwidth of 10 kHz and a video bandwidth of 30 kHz. A worst case modulation bandwidth of 445.000 kHz was measured. 13.560 MHz when reading a card ____________________________________________________________________________________________________________________________________________________________________________ Page 7 of 32 Test Report No 160108.1A 27th July 2016 This report may not be reproduced except in full.

13.560 MHz when awaiting a card Result: Complies. ____________________________________________________________________________________________________________________________________________________________________________ Page 8 of 32 Test Report No 160108.1A 27th July 2016 This report may not be reproduced except in full.

Section 15.207: Conducted emissions testing Conducted Emissions testing was carried out over the frequency range of 150 kHz to 30 MHz which was carried out at the laboratory’s MacKelvie Street premises in a 2.4 m x 2.4 m x 2.4 m screened room Testing was carried out using a representative AC power supply system that was powered at 120 Vac 60 Hz which supplied 12 Vdc to a Gallagher Controller 6000 device which in turn powered the Card Reader at 12 Vdc. The device operates on 125 kHz and 13.560 MHz. Testing was carried out with both transmitters operating with their standard antennas attached and when the 13.560 MHz antenna was removed and replaced with a dummy load. The device is deemed to comply providing it complies when the test is carried out with the dummy load attached and the overall emission signature for the product remains similar with no additional emissions being detected. This is the case with this device. The device was placed on top of the emissions table, which is 1 m x 1.5 m, 80 cm above the screened room floor which acts as the horizontal ground plane. In addition the device was positioned 40 cm away from the screened room wall which acts as the vertical ground plane. The artificial mains network was bonded to the screened room floor. At all times the device was kept more than 80 cm from the artificial mains network. The Class B limits have been applied. The supplied plot is combined plot showing the worst case quasi peak and average results of both the phase and neutral lines to the representative AC power supply. Quasi peak and average detectors have been used with resolution bandwidths of 9 kHz. Measurement uncertainty with a confidence interval of 95% is: - AC Mains port (0.15-30 MHz)  2.8 dB ____________________________________________________________________________________________________________________________________________________________________________ Page 9 of 32 Test Report No 160108.1A 27th July 2016 This report may not be reproduced except in full.

Conducted Emissions – AC Input Power Port - Normal Operating Mode Setup: Device tested when continuously reading a MiFare Access card when transmitting on 125 kHz and 13.560 MHz when powered at 120 Vac 60 Hz via an external power supply and control board. Peak --- Average -- Quasi Peak X Average + Level [dBµV] 70 60 x x 50 x x + 40 x xx + ++ + x + + + 30 + + ++ 20 10 0 150k 300k 500k 1M 2M 3M 5M 7M 10M 30M Frequency [Hz] Final Quasi-Peak Measurements Frequency Level Limit Margin Phase Rechecks (MHz) (dBV) (dBV) (dB) (dBV) 0.183000 53.40 64.4 11.0 L1 0.480000 47.60 56.4 8.8 L1 0.561000 47.00 56.0 9.0 L1 1.056000 34.30 56.0 21.7 L1 2.963000 38.40 56.0 17.6 N 3.291500 38.60 56.0 17.4 N 3.876500 39.80 56.0 16.2 N 13.56000 55.10 60.0 4.9 N Final Average Measurements Frequency Level Limit Margin Phase Rechecks (MHz) (dBV) (dBV) (dB) (dBV) 0.690000 29.90 46.0 16.1 N 0.987000 29.70 46.0 16.3 N 1.284000 30.30 46.0 15.7 N 1.380000 29.80 46.0 16.2 N 3.651500 35.00 46.0 11.0 N 4.934000 34.60 46.0 11.4 N 13.556000 45.50 50.0 4.5 N 13.560000 50.20 50.0 -0.2 L1 23.127500 37.20 50.0 12.8 L1 25.872500 37.70 50.0 12.3 N 26.484500 37.00 50.0 13.0 N 26.547500 36.40 50.0 13.6 N ____________________________________________________________________________________________________________________________________________________________________________ Page 10 of 32 Test Report No 160108.1A 27th July 2016 This report may not be reproduced except in full.

Conducted Emissions – AC Input Power Port Setup: Device tested when operating continuously when a resistive dummy load was attached to the 13.560 MHz transmitter when it was powered at 120 Vac 60 Hz via an external power supply and a control board. Peak --- Average -- Quasi Peak X Average + Level [dBµV] 70 60 50 x x x 40 xx x x + + + +++ + x 30 + + + + 20 10 0 150k 300k 500k 1M 2M 3M 5M 7M 10M 30M Frequency [Hz] Final Quasi-Peak Measurements Frequency Level Limit Margin Phase Rechecks MHz dBV dBV dB dBV 0.246000 51.20 61.9 10.7 L1 0.492000 47.60 56.1 8.5 L1 0.552000 46.80 56.0 9.2 N 1.086000 34.60 56.0 21.4 N 3.215000 38.30 56.0 17.7 N 3.345500 39.00 56.0 17.0 N 3.831500 39.60 56.0 16.4 N 4.439000 38.70 56.0 17.3 N Final Average Measurements Frequency Level Limit Margin Phase Rechecks MHz dBV dBV dB dBV 0.888000 29.20 46.0 16.8 N 0.987000 30.60 46.0 15.4 N 1.479000 31.20 46.0 14.8 N 1.974000 30.80 46.0 15.2 N 3.651500 35.00 46.0 11.0 N 4.439000 33.90 46.0 12.1 N 4.637000 34.60 46.0 11.4 N 4.835000 34.80 46.0 11.2 N 23.127500 37.10 50.0 12.9 L1 26.484500 36.80 50.0 13.2 N 26.547500 36.20 50.0 13.8 N 26.610500 36.80 50.0 13.2 N ____________________________________________________________________________________________________________________________________________________________________________ Page 11 of 32 Test Report No 160108.1A 27th July 2016 This report may not be reproduced except in full.

Section 15.209: Radiated emission limits, general requirements Radiated emissions testing was carried out over the frequency range of 100 kHz to 1000 MHz as the highest frequency in use has been stated to be les than 108 MHz (27.120 MHz). Testing was carried out at the laboratory’s open area test site - located at Driving Creek, Orere Point, Auckland, New Zealand. An enclosure containing absorber material, Panashield HYB-NF-12, has been placed between the turntable and the measurement antenna for when measurements are made above 1 GHz. This material has no absorbing affect below 1 GHz with site verification measurements confirming this. Testing was carried out using a representative AC power supply system that was powered at 120 Vac 60 Hz which supplied 12 Vdc to a Controller 6000 device which in turn powered the Card Reader also at 12 Vdc. The Controller 6000 and representative AC power supply were placed 5 metres directly behind the device under test (in the coffin). Testing was carried out with the device being placed in the centre of the test table standing vertically upright using a test jig. The device was transmitting continuously on 125 kHz and 13.560 MHz. Correct operation was confirmed periodically by placing a suitable card in front of the device which would give an audible beep. When an emission is located, it is positively identified and its maximum level is found by rotating the automated turntable, and by varying the antenna height, where appropriate, with an automated antenna tower. Below 30 MHz a magnetic loop is used with the centre of the loop being 1 metre above the ground with measurements being made using a quasi peak detector. Above 30 MHz the emission is measured in both vertical and horizontal antenna polarisations, where appropriate, using a quasi peak detector. The emission level was determined in field strength by taking the following into consideration: Level (dBV/m) = Receiver Reading (dBV) + Antenna Factor (dB/m) + Coax Loss (dB) Result: Complies Measurement uncertainty with a confidence interval of 95% is: - Free radiation tests (30 – 1000 MHz)  4.1 dB - Free radiation tests (100 kHz – 30 MHz)  4.8 dB ____________________________________________________________________________________________________________________________________________________________________________ Page 12 of 32 Test Report No 160108.1A 27th July 2016 This report may not be reproduced except in full.

Section 15.209: 125 kHz Fundamental emission: Measurements were made using a magnetic loop antenna and a receiver with an average detector and a peak detector both using a 9 kHz bandwidth Frequency Level Limit Margin Detector Distance (kHz) (dBuV/m) (dBuV/m) (dB) (metres) 125.000 50.0 84.7 29.7 Average 10 125.000 55.0 104.7 36.6 Peak 10 Measurements were made at a distance of 10 metres with the limit being determined by using the extrapolation factor of 40 dB per decade limit as detailed in section 15.31 f (2). The 300 metre limit between 125 – 490 kHz has been scaled by a factor of 40 dB per decade, as per section 15.31 (f) (2). The average limit at 300 m at 125.0 kHz is 19.2 uV/m or 25.7 dBuV/m and 45.7 dBuV/m in peak. = 25.7 dBuV/m + -40 dB/decade * (log (10) - log (300)) = 25.7 dBuV/m + -40 dB/decade * (1.000 - 2.477) = 25.7 dBuV/m + -40 dB/decade * - 1.477 = 25.7 dBuV/m + 59.08 = 84.7 dBuV/m This gives a limit at 10 m at 134.2 kHz of 84.7 dBuV/m and 104.7 dBuV/m in peak Testing was also carried out to determine whether a variation in the supply voltage would cause a significant change in the peak field strength. As a worst case indication the 12 Vdc supply to the card reader was varied by +/- 15% between 10.2 Vdc and 13.8 Vdc. Voltage Peak Field Strength (Vdc) (dBuV/m) 10.2 55.0 12.0 55.0 13.8 55.0 Result: Complies. Measurement uncertainty with a confidence interval of 95% is: - Free radiation tests (100 kHz – 30 MHz)  4.8 dB ____________________________________________________________________________________________________________________________________________________________________________ Page 13 of 32 Test Report No 160108.1A 27th July 2016 This report may not be reproduced except in full.

Section 15.209: 125 kHz Spurious Emissions (below 30 MHz) A receiver with an average detector and a peak detector using a 9 kHz bandwidth was used between 110 – 490 kHz and a quasi peak detector with a 9 kHz bandwidth was used between 490 kHz – 30.0 MHz. Frequency Level Limit Margin Detector Comment (kHz) (dBuV/m) (dBuV/m) (dB) 250.000 44.0 78.7 - Average Noise Floor 250.000 54.0 98.7 - Peak Noise Floor 375.000 46.0 75.2 - Average Noise Floor 375.000 56.0 95.2 - Peak Noise Floor 500.000 43.0 52.7 - Quasi Peak Noise Floor 625.000 40.0 50.8 - Quasi Peak Ambient 750.000 34.0 49.2 - Quasi Peak Noise Floor 875.000 33.0 47.8 - Quasi Peak Ambient 1000.000 30.0 46.7 - Quasi Peak Noise Floor 1125.000 32.0 45.7 - Quasi Peak Noise Floor 1250.000 35.0 44.7 - Quasi Peak Ambient 1375.000 26.0 43.9 - Quasi Peak Noise Floor 1500.000 28.0 43.2 - Quasi Peak Noise Floor 1625.000 24.0 42.5 - Quasi Peak Noise Floor 1750.000 24.0 48.6 - Quasi Peak Noise Floor 1875.000 22.0 48.6 - Quasi Peak Noise Floor Magnetic loop measurements were made a distance of 10 metres with the measurement antenna being further adjusted to give the highest field strength. The 300 metre limit between 125 – 490 kHz has been scaled by a factor of 40 dB per decade, as per section 15.31 (f) (2). = Limit (dBuV/m) + -40 dB/decade * (log (10) - log (300)) = Limit (dBuV/m) + -40 dB/decade * (1.000 - 2.477) = Limit (dBuV/m) + -40 dB/decade * - 1.477 = Limit (dBuV/m) + 59.08 The limit between 110 – 490 kHz was increased by 20 dB when the peak detector was used. The 30 metre limit between 490 – 1705 kHz has been scaled by a factor of 40 dB per decade, as per section 15.31 (f) (2). = Limit (dBuV/m) + -40 dB/decade * (log (10) - log (30)) = Limit (dBuV/m) + -40 dB/decade * (1.000 - 1.477) = Limit (dBuV/m) + -40 dB/decade * - 0.477 = Limit (dBuV/m) + 19.08 The spurious emissions observed do not exceed the level of the fundament emission. Result: Complies. Measurement uncertainty with a confidence interval of 95% is: - Free radiation tests (100 kHz – 30 MHz)  4.8 dB ____________________________________________________________________________________________________________________________________________________________________________ Page 14 of 32 Test Report No 160108.1A 27th July 2016 This report may not be reproduced except in full.

Section 15.209: 13.560 MHz transmitter below 30 MHz spurious emission measurements Frequency Level Limit Margin (MHz) (dBμV/m) (dBμV/m) (dB) 27.120 22.3 48.6 26.3 Testing was carried out when the device was transmitting continuously. Magnetic loop measurements were attempted at a distance of 10 metres. A receiver with a quasi peak detector with a 9 kHz bandwidth was used between 490 kHz – 30.0 MHz. The 30 metre limit between 1.705 MHz – 30 MHz has been scaled by a factor of 40 dB per decade, as per section 15.31 (f) (2). The limit at 27.122 MHz when measured at 30 metres is 30 uV/m or 29.54 dBuV/m. Therefore when scaled the limit at 10 metres will be 48.6 dBuV/m as detailed below. = 29.54 dBuV/m + -40 dB/decade * (log (10) - log (30)) = 29.54 dBuV/m + -40 dB/decade * (1.000 - 1.477) = 29.54 dBuV/m + -40 dB/decade * - 0.477 = 29.54 dBuV/m + 19.08 = 48.6 dBuV/m The spurious emission observed does not exceed the level of the fundament emission Result: Complies. Measurement uncertainty with a confidence interval of 95% is: - Free radiation tests (100 kHz – 30 MHz)  4.8 dB ____________________________________________________________________________________________________________________________________________________________________________ Page 15 of 32 Test Report No 160108.1A 27th July 2016 This report may not be reproduced except in full.

Section 15.209: Spurious Emissions (above 30 MHz) Measurements between 30 –2000 MHz have been made at a distance of 3 metres. A receiver with a quasi peak detector with a 120 kHz bandwidth was used between 30 – 1000 MHz and with a peak and average detector with a 1 MHz bandwidth was used between 1000 – 2000 MHz. The limits as described in Section 15.209 have been applied. Harmonics Frequency Vertical Horizontal Limit Margin Antenna Detector BW (MHz) (dBμV/m) (dBμV/m) (dBμV/m) (dB) Pol. (kHz) 40.680 37.4 19.1 40.0 2.6 Vertical QP 120 54.240 16.1 - 40.0 23.9 Vertical QP 120 67.800 22.0 - 40.0 18.0 Vertical QP 120 Other emissions Frequency Vertical Horizontal Limit Margin Antenna Detector BW (MHz) (dBμV/m) (dBμV/m) (dBμV/m) (dB) Pol. (kHz) 351.000 27.1 - 46.0 18.9 Vertical QP 120 366.000 - 26.8 46.0 19.2 Vertical QP 120 384.000 22.9 - 46.0 18.0 Vertical QP 120 All other emissions observed had a margin to the limit that exceeded 15 dB when measurements were attempted over the range of 30 – 2000 MHz using both vertical and horizontal polarisations. Result: Complies. Measurement uncertainty with a confidence interval of 95% is: - Free radiation tests (30 MHz – 2000 MHz)  4.1 dB ____________________________________________________________________________________________________________________________________________________________________________ Page 16 of 32 Test Report No 160108.1A 27th July 2016 This report may not be reproduced except in full.

Section 15.225: Fundamental emission: Measurements were made using a magnetic loop antenna and a receiver with a quasi peak detector using a 9 kHz bandwidth Measurements were made at a distance of 10 metres with the limit being determined by using the extrapolation factor of 40 dB per decade limit, as detailed in section 15.31 f (2). The limit at 30 m at 13.560 MHz is 15,848 uV/m or 84.0 dBuV/m. Applying the extrapolation factor of 40 dB/ per decade, the limit is 103.1 dBuV/m. = 84.0 dBuV/m + -40 dB/decade * (log (10) - log (30)) = 84.0 dBuV/m + 19.08 = 103.1 dBuV/m As a worst case testing was also carried out when the device was transmitting continuously when the 12.0 Vdc supply to the device was varied by +/- 15%. Frequency Level Distance Limit Voltage Margin (MHz) (dBuV/m) (metres) (dBuV/m) (Vdc) (dB) 13.560 52.9 10.0 103.1 10.2 50.2 13.560 52.9 10.0 103.1 12.0 50.2 13.560 53.0 10.0 103.1 13.8 50.1 A representative spectrum analyser plot shows that the carrier and modulation peaks within, +/- 1 MHz and +/- 5 MHz of the carrier. Result: Complies. Measurement uncertainty with a confidence interval of 95% is: - Free radiation tests (100 kHz – 30 MHz)  4.8 dB ____________________________________________________________________________________________________________________________________________________________________________ Page 17 of 32 Test Report No 160108.1A 27th July 2016 This report may not be reproduced except in full.

Reading a card with a 1 MHz span Reading a card with a 5 MHz span ____________________________________________________________________________________________________________________________________________________________________________ Page 18 of 32 Test Report No 160108.1A 27th July 2016 This report may not be reproduced except in full.

Awaiting a card with a 1 MHz span Awaiting a card with a 5 MHz span ____________________________________________________________________________________________________________________________________________________________________________ Page 19 of 32 Test Report No 160108.1A 27th July 2016 This report may not be reproduced except in full.

Section 15.225: Frequency tolerance: The frequency tolerance of the carrier is required to be +/- 0.01% of operating frequency when the temperature is varied between -20 degrees and +50 degrees. The device operates nominally on 13.560 MHz which gives a frequency tolerance of +/- 1,356 Hz. Temperature Frequency Difference (C) (MHz) (Hz) -20.0 13.559 525 -475 -10.0 13.559 530 -470 0.0 13.559 520 -480 10.0 13.559 490 -510 20.0 13.559 462 -538 30.0 13.559 455 -545 40.0 13.559 435 -565 50.0 13.559 405 -595 Variation of the 120 Vac 60 Hz supply to the AC power supply did not vary the 12 Vdc supply to the Controller 6000 or the device under test. As a worst case scenario the 12 Vdc supply to the device was varied between 85% and 115% of the supply voltage at +20 degrees. Voltage Frequency Difference (Vdc) (MHz) (Hz) 10.2 13.559 462 -538 12.0 13.559 462 -538 13.8 13.559 462 -538 Result: Complies Measurement uncertainty with a confidence interval of 95% is: - Frequency tolerance  50 Hz ____________________________________________________________________________________________________________________________________________________________________________ Page 20 of 32 Test Report No 160108.1A 27th July 2016 This report may not be reproduced except in full.

7. TEST EQUIPMENT USED Instrument Manufacturer Model Serial No Asset Ref Period Cal Due AC Supply APT 7008 4170003 - - Not applicable Aerial Controller EMCO 1090 9112-1062 RFS 3710 - Not applicable Aerial Mast EMCO 1070-1 9203-1661 RFS 3708 - Not applicable Biconical Schwarzbeck BBA 9106 - RFS 3612 3 years 5 Feb 2017 Log Periodic Schwarzbeck VUSLP 9111 9111-228 3785 3 years 5 Feb 2017 Loop Antenna EMCO 6502 9003-2485 3798 3 years 7 Jul 2017 Mains Network R&S ESH2-Z5 881362/032 3628 2 years 2 Oct 2016 Receiver R&S ESHS 10 828404/005 3728 1 year 27 June 2016 Receiver R&S ESIB-40 100171 R-27-1 1 year 15 Feb 2017 Turntable EMCO 1080-1-2.1 9109-1578 RFS 3709 - Not applicable VHF Balun Schwarzbeck VHA 9103 - RFS 3603 3 years 5 Feb 2017 8. ACCREDITATIONS Testing was carried out in accordance with EMC Technologies Ltd registration with the Federal Communications Commission as a listed facility, registration number: 90838, which was updated in June 2014. All testing was carried out in accordance with the terms of EMC Technologies (NZ) Ltd International Accreditation New Zealand (IANZ) Accreditation to NZS/ISO/IEC 17025. All measurement equipment has been calibrated in accordance with the terms of the EMC Technologies (NZ) Ltd International Accreditation New Zealand (IANZ) Accreditation to NZS/ISO/IEC 17025. International Accreditation New Zealand has Mutual Recognition Arrangements for testing and calibration with various accreditation bodies in a number of economies. This includes NATA (Australia), UKAS (UK), SANAS (South Africa), NVLAP (USA), A2LA (USA), SWEDAC (Sweden). Further details can be supplied on request. ____________________________________________________________________________________________________________________________________________________________________________ Page 21 of 32 Test Report No 160108.1A 27th July 2016 This report may not be reproduced except in full.

9. PHOTOGRAPHS External Photos ____________________________________________________________________________________________________________________________________________________________________________ Page 22 of 32 Test Report No 160108.1A 27th July 2016 This report may not be reproduced except in full.

Conducted emissions test set up ____________________________________________________________________________________________________________________________________________________________________________ Page 23 of 32 Test Report No 160108.1A 27th July 2016 This report may not be reproduced except in full.

____________________________________________________________________________________________________________________________________________________________________________ Page 24 of 32 Test Report No 160108.1A 27th July 2016 This report may not be reproduced except in full.

Radiated emissions test set up ____________________________________________________________________________________________________________________________________________________________________________ Page 25 of 32 Test Report No 160108.1A 27th July 2016 This report may not be reproduced except in full.

____________________________________________________________________________________________________________________________________________________________________________ Page 26 of 32 Test Report No 160108.1A 27th July 2016 This report may not be reproduced except in full.

Ancillary equipment test set up ____________________________________________________________________________________________________________________________________________________________________________ Page 27 of 32 Test Report No 160108.1A 27th July 2016 This report may not be reproduced except in full.

Test Site Description ____________________________________________________________________________________________________________________________________________________________________________ Page 28 of 32 Test Report No 160108.1A 27th July 2016 This report may not be reproduced except in full.

____________________________________________________________________________________________________________________________________________________________________________ Page 29 of 32 Test Report No 160108.1A 27th July 2016 This report may not be reproduced except in full.

EMCO Loop antenna (9 kHz - 30 MHz) ____________________________________________________________________________________________________________________________________________________________________________ Page 30 of 32 Test Report No 160108.1A 27th July 2016 This report may not be reproduced except in full.

Biconnical Antenna (30 - 300 MHz) ____________________________________________________________________________________________________________________________________________________________________________ Page 31 of 32 Test Report No 160108.1A 27th July 2016 This report may not be reproduced except in full.

Schwarzbeck Log Periodic Antenna (300 - 2000 MHz) ____________________________________________________________________________________________________________________________________________________________________________ Page 32 of 32 Test Report No 160108.1A 27th July 2016 This report may not be reproduced except in full.


Document Created: 2016-07-27 10:50:41
Document Modified: 2016-07-27 10:50:41
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC