Test Report

FCC ID: M45-46066

Test Report

Download: PDF

FCCID_2086460

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: M45-46066 Report No.: LCS130916414F

FCC TEST REPORT

FOR

Estes-Cox Corporation d/b/a Estes Industries and Cox

Proto X

Model No.: ESTE4606

Prepared for : Estes-Cox Corporation d/b/a Estes Industries and Cox
Address : 1295 H Street, Penrose, Colorado 81240 United States

Prepared by : Shenzhen LCS Compliance Testing Laboratory Ltd
Address : 1/F., Xingyuan Industrial Park, Tongda Road, Bao’an Avenue,
Bao’an District, Shenzhen, Guangdong, China

Date of receipt of test sample : September 16, 2013
Number of tested samples : 1
Serial number : Prototype
Date of Test : September 16, 2013 - September 26, 2013
Date of Report : September 26, 2013

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 1 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: M45-46066 Report No.: LCS130916414F

FCC -- TEST REPORT

September 26, 2013
Test Report No. : LCS130916414F Date of issue

Type / Model........................... : ESTE4606

EUT......................................... : Proto X

Applicant............................... : Estes-Cox Corporation d/b/a Estes Industries and Cox

Address.................................. : 1295 H Street, Penrose, Colorado 81240 United States

Telephone............................... : /
Fax.......................................... : /

Manufacturer........................ : Shenzhen Hubsan Technology Co., Ltd.
Address................................... : Rm407, Municipal Service Building, Hong Li Road west, Futian
District, Shenzhen, China

Telephone............................... : /
Fax.......................................... : /

Factory................................... : Shenzhen Hubsan Technology Co., Ltd.
Address................................... : Rm407, Municipal Service Building, Hong Li Road west, Futian
District, Shenzhen, China
Telephone............................... : /
Fax.......................................... : /

Test Result Positive
The test report merely corresponds to the test sample.
It is not permitted to copy extracts of these test result without the written permission of the test
laboratory.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 3 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: M45-46066 Report No.: LCS130916414F

TABLE OF CONTENTS
1. GENERAL INFORMATION ..................................................................................................... 5
1.1. Description of Device (EUT) .............................................................................................................. 5
1.2. Host System Configuration List and Details ....................................................................................... 5
1.3. External I/O ......................................................................................................................................... 5
1.4. Description of Test Facility ................................................................................................................. 6
1.5. Statement of the measurement uncertainty .......................................................................................... 6
1.6. Measurement Uncertainty.................................................................................................................... 6
1.7. Description Of Test Modes ................................................................................................................. 7
2. TEST METHODOLOGY ........................................................................................................... 8
2.1. EUT Configuration .............................................................................................................................. 8
2.2. EUT Exercise ....................................................................................................................................... 8
2.3. General Test Procedures ...................................................................................................................... 8
3. CONNECTION DIAGRAM OF TEST SYSTEM ................................................................... 9
3.1. Justification ......................................................................................................................................... 9
3.2. EUT Exercise Software ....................................................................................................................... 9
3.3. Special Accessories ............................................................................................................................. 9
3.4. Block Diagram/Schematics ................................................................................................................. 9
3.5. Equipment Modifications .................................................................................................................... 9
3.6. Test Setup ............................................................................................................................................ 9
4. SUMMARY OF TEST RESULTS ........................................................................................... 10
5. ANTENNA REQUIREMENT .................................................................................................. 11
5.1. Standard Applicable .......................................................................................................................... 11
5.2. Antenna Connected Construction ...................................................................................................... 11
6. RADIATED EMISSION MEASUREMENT .......................................................................... 12
6.1. Standard Applicable .......................................................................................................................... 12
6.2. Measuring Instruments and Setting ................................................................................................... 12
6.3. Test Procedure ................................................................................................................................... 13
6.4. Test Equipment List and Details ....................................................................................................... 14
6.5. Block Diagram of Test Setup ............................................................................................................ 14
6.6. Test Results ....................................................................................................................................... 15
7. BAND EDGES MEASUREMENT .......................................................................................... 23
7.1. Standard Applicable .......................................................................................................................... 23
7.2. Test Equipment List and Details ....................................................................................................... 23
7.3. Block Diagram of Test Setup ............................................................................................................ 23
7.4. Test Procedure ................................................................................................................................... 23
7.5. Test Results ....................................................................................................................................... 24
8. 20 DB BANDWIDTH MEASUREMENT ............................................................................... 26
8.1. Standard Applicable .......................................................................................................................... 26
8.2. Test Equipment List and Details ....................................................................................................... 26
8.3. Block Diagram of Test Setup ............................................................................................................ 26
8.4. Test Procedure ................................................................................................................................... 26
8.5. Test Results ....................................................................................................................................... 27
9. MANUFACTURER/ APPROVAL HOLDER DECLARATION ......................................... 29

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 4 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: M45-46066 Report No.: LCS130916414F

1. GENERAL INFORMATION
1.1. Description of Device (EUT)

EUT : Proto X

Model Number : ESTE4606

Power Supply : DC 3.0V by 2*AAA batteries

Frequency Range : 2410.00-2465.00MHz, (Channel Number: 12, Channel
Frequency=2410+5*(K-1), K=1, 2, 3 ……12)

Modulation Technology : GFSK

Channel Number : 12

Channel Spacing : 5MHz

Antenna Type and Gain : PCB Antenna, 1.8dBi(Max.)

1.2. Host System Configuration List and Details

Manufacturer Description Model Serial Number Certificate

-- -- -- -- --

1.3. External I/O

I/O Port Description Quantity Cable

-- -- --

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 5 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: M45-46066 Report No.: LCS130916414F

1.4. Description of Test Facility
Site Description
EMC Lab. : Accredited by CNAS, June 04, 2010
The Certificate Registration Number. is L4595.
Accredited by FCC, July 14, 2011
The Certificate Registration Number. is 899208.
Accredited by Industry Canada, May. 02, 2011
The Certificate Registration Number. is 9642A-1

1.5. Statement of the measurement uncertainty
The data and results referenced in this document are true and accurate. The reader is
cautioned that there may be errors within the calibration limits of the equipment and
facilities. The measurement uncertainty was calculated for all measurements listed in
this test report acc. To CISPR 16 – 4 “Specification for radio disturbance and immunity
measuring apparatus and methods – Part 4: Uncertainty in EMC Measurements” and is
documented in the LCS quality system acc. To DIN EN ISO/IEC 17025. Furthermore,
component and process variability of devices similar to that tested may result in
additional deviation. The manufacturer has the sole responsibility of continued
compliance of the device.

1.6. Measurement Uncertainty
Test Item Frequency Range Uncertainty Note
9KHz~30MHz ±3.10dB (1)
30MHz~200MHz ±2.96dB (1)
Radiation Uncertainty :
200MHz~1000MHz ±3.10dB (1)
1GHz~26.5GHz ±4.00dB (1)
Conduction Uncertainty : 150kHz~30MHz ±1.63dB (1)
Power disturbance : 30MHz~300MHz ±1.60dB (1)

(1). This uncertainty represents an expanded uncertainty expressed at approximately the
95% confidence level using a coverage factor of k=2.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 6 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: M45-46066 Report No.: LCS130916414F

1.7. Description Of Test Modes
The EUT operates in the unlicensed ISM band at 2.4GHz. The following operating
modes were applied for the related test items. And the new battery is used during the
measurement.
The EUT received DC 3.0V power from 2*AAA batteries which are new and full
power.
All test modes were tested, only the result of the worst case was recorded in the report.

The EUT is considered a portable unit; it was pre-tested on the positioned of each 3 axis.
The worst case was found positioned on X-plane. Therefore only the test data of this
X-plane was used for radiated emission measurement test.

Mode of Operations Transmitting Frequency
(MHz)
2410
GFSK 2435
2465
For Conducted Emission
Test Mode N/A
For Radiated Emission
Test Mode TX Mode
Note: The EUT is designed to use DC 3.0V 2*AAA batteries for power supply, so the
conducted emission testing is not applicable.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 7 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: M45-46066 Report No.: LCS130916414F

3. CONNECTION DIAGRAM OF TEST SYSTEM

3.1. Justification
The system was configured for testing in a continuous transmit condition.

3.2. EUT Exercise Software
N/A

3.3. Special Accessories
N/A

3.4. Block Diagram/Schematics
Please refer to the related document

3.5. Equipment Modifications
Shenzhen LCS Compliance Testing Laboratory Ltd. has not done any modification on
the EUT.

3.6. Test Setup
Please refer to the test setup photo.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 9 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: M45-46066 Report No.: LCS130916414F

6. RADIATED EMISSION MEASUREMENT

6.1. Standard Applicable
1. Emissions radiated outside of the specified frequency bands, except for harmonics,
shall be attenuated by at least 50 dB below the level of the fundamental or to the
general radiated emission limits in §15.209, whichever is the lesser attenuation.
2. 20dBc in any 100 kHz bandwidth outside the operating frequency band. In case the
emission fall within the restricted band specified on 15.205(a), then the 15.209(a) and
15.249 limit in the table below has to be followed.

Fundamental Field Strength of fundamental Field Strength of harmonics
Frequency (millivolts/meter) (microvolts/meter)
902-928MHz 50 500
2400-2483.5MHz 50 500

5725-5875MHz 50 500

24.0-24.25GHz 250 2500

Frequencies Field Strength Measurement Distance
(MHz) (microvolts/meter) (meters)
0.009~0.490 2400/F(KHz) 300
0.490~1.705 24000/F(KHz) 30
1.705~30.0 30 30
30~88 100 3
88~216 150 3
216~960 200 3
Above 960 500 3

6.2. Measuring Instruments and Setting
Please refer to section 5 of equipments list in this report. The following table is the
setting of spectrum analyzer and receiver.

Spectrum Parameter Setting
Attenuation Auto
Start ~ Stop Frequency 9kHz~150kHz / RB 200Hz for QP
Start ~ Stop Frequency 150kHz~30MHz / RB 9kHz for QP

Start ~ Stop Frequency 30MHz~1000MHz / RB 120kHz for QP

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 12 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: M45-46066 Report No.: LCS130916414F

Spectrum Parameter Setting
Attenuation Auto
Start Frequency 1000 MHz
Stop Frequency 10th carrier harmonic
RB / VB (Emission in restricted band) 1MHz / 1MHz for Peak, 1 MHz / 10Hz for Average
RB / VB (Emission in non-restricted band) 1000KHz / 1000KHz for peak

6.3. Test Procedure
1. Configure the EUT according to ANSI C63.4. The EUT was placed on the top of the
turntable 0.8 meter above ground. The phase center of the receiving antenna mounted on
the top of a height-variable antenna tower was placed 3 meters far away from the
turntable.

2. Power on the EUT and all the supporting units. The turntable was rotated by 360
degrees to determine the position of the highest radiation.

3. The height of the broadband receiving antenna was varied between one meter and four
meters above ground to find the maximum emissions field strength of both horizontal
and vertical polarization.

4. For each suspected emissions, the antenna tower was scan (from 1 m to 4 m) and then
the turntable was rotated (from 0 degree to 360 degrees) to find the maximum reading.

5. Set the test-receiver system to Peak or CISPR quasi-peak Detect Function with
specified bandwidth under Maximum Hold Mode.

6. For emissions above 1GHz, use 1MHz VBW and RBW for peak reading. Then 1MHz
RBW and 10Hz VBW for average reading in spectrum analyzer.

7. When the radiated emissions limits are expressed in terms of the average value of the
emissions, and pulsed operation is employed, the measurement field strength shall be
determined by averaging over one complete pulse train, including blanking intervals, as
long as the pulse train does not exceed 0.1 seconds. As an alternative (provided the
transmitter operates for longer than 0.1 seconds) or in cases where the pulse train
exceeds 0.1 seconds, the measured field strength shall be determined from the average
absolute voltage during a 0.1 second interval during which the field strength is at its
maximum value.

8. If the emissions level of the EUT in peak mode was 3 dB lower than the average limit
specified, then testing will be stopped and peak values of EUT will be reported,
otherwise, the emissions which do not have 3 dB margin will be repeated one by one
using the quasi-peak method for below 1GHz.

9. For testing above 1GHz, the emissions level of the EUT in peak mode was lower than
average limit (that means the emissions level in peak mode also complies with the limit
in average mode), then testing will be stopped and peak values of EUT will be reported,
otherwise, the emissions will be measured in average mode again and reported.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 13 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: M45-46066 Report No.: LCS130916414F

Antenna
tower

3m Horn
antenna
EUT
4m
Spectrum
analyzer

Turntable 1m
0.8m
Pre-amp

Above 10 GHz shall be extrapolated to the specified distance using an extrapolation
factor of 20 dB/decade form 3m to 1.5m.
Distance extrapolation factor = 20 log (specific distanc [3m] / test distance [1.5m])
(dB);
Limit line = specific limits (dBuV) + distance extrapolation factor [6 dB].

6.6. Test Results
Results of Radiated Emissions (9kHz~30MHz)

Frequency Level Over Limit Over Limit
Remark
(MHz) (dBuV) (dB) (dBuV)
See Note

Note:
The amplitude of spurious emissions which are attenuated by more than 20 dB below
the permissible value has no need to be reported.
Distance extrapolation factor = 40 log (specific distance / test distance) (dB);
Limit line = specific limits (dBuV) + distance extrapolation factor.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 15 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: M45-46066 Report No.: LCS130916414F

Notes:
1. Measuring frequencies from 9k~10th harmonic (ex. 26GHz), No emission found between
lowest internal used/generated frequency to 30MHz.
2. Radiated emissions measured in frequency range from 9k~10th harmonic (ex. 26GHz)
were made with an instrument using Peak detector mode.
3. No emission was be recorded above 18GHz means the reading of emissions are attenuated
more than 20dB below the permissible limits or the field strength is too small to be
measured.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 22 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: M45-46066 Report No.: LCS130916414F

9. MANUFACTURER/ APPROVAL HOLDER DECLARATION

The following identical model(s):

-- -- --

Belong to the tested device:

Product description : Proto X
Model name : ESTE4606

Remark: No additional models were tested.

------------THE END OF REPORT----------

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 29 of 29

Document Created: 2013-09-29 14:31:17
Document Modified: 2013-09-29 14:31:17

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC