Test report

FCC ID: LH8RP-S435

Test Report

Download: PDF
FCCID_128275

FCC ID: LH8RP—S435 2) EMCC PAGE 1 of 12 ‘ DR. RASEK TEST REPORT # EMCC—950295A0B, 2000—NOV—21 EQUIPMENT UNDER TEST: Trade Name: $435 Model: RPS435000.0US Serial No: None Equipment Category: Receiver Manufacturer: CARDIN ELETTRONICA SPA Address: Via Raffaello 36 31020 S. Vendemiano (TV) Italy Phone: +39—0438—401818 Fax: +39—0438—401831 RELEVANT STANDARD: 47 CFR Part 15B — Unintentional Radiators MEASUREMENT PROCEDURE USED: [X Anisi C63.4—1992 [] FCC/OET MP—4 (1987) [_] Other TEST REPORT PREPARED BY: Reinhard Sauerschell EMCC DR. RASEK Moggast 72—74 91320 Ebermannstadt Germany Phone: +49 9194 9016 Fax: +49 9194 8125 E—mail: r.sauerschell@emcce.de TEST PERSONNEL: SIGNATURE OF THE COMPANY OFFICIAL: Reinhard Sauerschell M Dr. Werner G. RaSsek — President— EMCC DR. RASEK RADIO LABORATORIES Telephone: +49—9194—9016 Moggast 72—74 EMC LABORATORIES Telefax: +49—9194—8125 91320 Ebermannstadt e Mail: emc.cons@emecc.de Germany Rat cssz Web: http://www.emee.de FCC Registration # 90566 TTI—P—G 094/94 TTI—P—G 074/95 fee_RPS435.doc

FCC ID: LH8RP-S435 Test Report #EMCC-950295AOB Page 2 of 12 Issue Date: 2000-NOV-21 TEST OF CARDIN ELETTRONICA SPA S435 MODEL RPS435000.0US TO 47 CFR PART 15B - UNINTENTIONAL RADIATORS CONTENTS Page 1 GENERAL INFORMATION ..................................................................................................................................................................... 3 1.1 Purpose........................................................................................................................................................................................ 3 1.2 Limits and Reservations............................................................................................................................................................. 3 1.3 Test Location............................................................................................................................................................................... 3 1.4 Manufacturer ............................................................................................................................................................................... 3 1.5 Dates ............................................................................................................................................................................................ 3 2 PRODUCT DESCRIPTION...................................................................................................................................................................... 4 2.1 Equipment Under Test (EUT) ..................................................................................................................................................... 4 2.2 Configuration and Peripherals of EUT ...................................................................................................................................... 4 2.3 Mode of Operation During Testing ............................................................................................................................................ 4 2.4 Modifications Required for Compliance.................................................................................................................................... 4 3 TEST RESULTS SUMMARY .................................................................................................................................................................. 5 4 CONDUCTED EMISSIONS TESTS ........................................................................................................................................................ 6 4.1 Regulation.................................................................................................................................................................................... 6 4.2 Test Equipment ........................................................................................................................................................................... 6 4.3 Test Procedures .......................................................................................................................................................................... 6 4.4 Test Results................................................................................................................................................................................. 7 5 RADIATED EMISSIONS TEST ............................................................................................................................................................... 8 5.1 Regulation.................................................................................................................................................................................... 8 5.2 Test Equipment ........................................................................................................................................................................... 9 5.3 Test Procedures ........................................................................................................................................................................ 10 5.4 Field Strength Calculation........................................................................................................................................................ 10 5.5 Test Results............................................................................................................................................................................... 11 6 MISCELLANEOUS COMMENTS AND NOTES.................................................................................................................................... 12 7 LIST OF ANNEXES............................................................................................................................................................................... 12 FCC_RPS435.DOC

FCC ID: LH8RP-S435 Test Report #EMCC-950295AOB Page 3 of 12 Issue Date: 2000-NOV-21 TEST OF CARDIN ELETTRONICA SPA S435 MODEL RPS435000.0US TO 47 CFR PART 15B - UNINTENTIONAL RADIATORS 1 GENERAL INFORMATION 1.1 Purpose The purpose of this report is to show compliance to the FCC regulations for unintentional radiators operating under section 15.101 ff. of the Code of Federal Regulations title 47. 1.2 Limits and Reservations The test results in this report apply only to the particular Equipment Under Test (EUT) as declared in this report. This test report shall not be reproduced except in full without the written permission of EMCC DR. RAŠEK. 1.3 Test Location Company Name: EMCC DR. RAŠEK Street: Moggast 72-74 City: 91320 Ebermannstadt Country: Germany Laboratory: Test Laboratory of EMCC DR. RAŠEK FCC Registration Number: 90566 This site has been fully described in a report submitted to the FCC, and accepted in the letter dated February 09, 2000 Registration Number 90566. Phone: +49-9194-9016 Fax: +49-9194-8125 E-Mail: emc.cons@emcc.de Web: www.emcc.de 1.4 Manufacturer Company Name: CARDIN ELETTRONICA SPA Street: Via Raffaello 36 City: 31020 S. Vendemiano (TV) Country: Italy Name for contact purposes: Mr. Maurizio Terruso Phone: +39-0438-401818 Fax: +39-0438-401831 E-mail: cert@cardin.it 1.5 Dates Date of receipt of EUT: CW 42/2000 Test date: CW 42-43/2000 FCC_RPS435.DOC

FCC ID: LH8RP-S435 Test Report #EMCC-950295AOB Page 4 of 12 Issue Date: 2000-NOV-21 TEST OF CARDIN ELETTRONICA SPA S435 MODEL RPS435000.0US TO 47 CFR PART 15B - UNINTENTIONAL RADIATORS 2 PRODUCT DESCRIPTION 2.1 Equipment Under Test (EUT) Device: Remote Control (RF) Superheterodyne Receiver for automatic opening systems Model: RPS435000.0US Serial Number: None Power: 120 VAC Receive Frequency: 433.92 MHz, one RF channel Antenna: external Interface ports: relay output ports for 120VAC switching purposes FCC ID: LH8RP-S435 2.2 Configuration and Peripherals of EUT The EUT was tested as stand-alone device. The antenna (16 cm rod antenna) provided by the manufacturer was installed and used during tests. Cables were attached to the relay output ports. 2.3 Mode of Operation During Testing The receiver were tested in a typical fashion. During testing the receiver operated with and without its appropriate receive signal. 2.4 Modifications Required for Compliance None. FCC_RPS435.DOC

FCC ID: LH8RP-S435 Test Report #EMCC-950295AOB Page 5 of 12 Issue Date: 2000-NOV-21 TEST OF CARDIN ELETTRONICA SPA S435 MODEL RPS435000.0US TO 47 CFR PART 15B - UNINTENTIONAL RADIATORS 3 TEST RESULTS SUMMARY Summary of Test Results Receiver, model RPS435000.0US Requirement CFR Section Report Section Test Result Conducted Emissions 15.107 4 Pass Radiated Spurious Emissions 15.109, 15.205(b) 5 Pass The client has made the determination that EUT Condition, Characterization, and Mode of Operation are representative of production units, and meet the requirements of the specifications referenced herein. Consistent with Industry practice, measurement and test equipment not directly involved in obtaining measurement results but having an impact on measurements (such as cable loss, antenna factors, etc.) are factored into the "Correction Factor" documented in certain test results. Instrumentation employed for testing meets tolerances consistent with known Industry Standards and Regulations. The measurements contained in this report were made in accordance with the procedure ANSI C63.4 - 1992 and all applicable Public Notices received prior to the date of testing. All emissions from the device were found to be within the limits outlined in this report. The test results in this report apply only to the particular Equipment Under Test (EUT) as declared in this report. Test Personnel: Reinhard Sauerschell Issuance Date: 2000-11-21 FCC_RPS435.DOC

FCC ID: LH8RP-S435 Test Report #EMCC-950295AOB Page 6 of 12 Issue Date: 2000-NOV-21 TEST OF CARDIN ELETTRONICA SPA S435 MODEL RPS435000.0US TO 47 CFR PART 15B - UNINTENTIONAL RADIATORS 4 CONDUCTED EMISSIONS TESTS Test Requirement: FCC CFR47, Part 15B Test Procedure: ANSI C63.4:1992 4.1 Regulation Section 15.107 (a) Except for Class A digital devices, for equipment that is designed to be connected to the public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power line on any frequency or frequencies within the band 450 kHz to 30 MHz shall not exceed 250 microvolts. Compliance with this provision shall be based on the measurement of the radio frequency voltage between each power line and ground at the power terminals. Section 15.107 (f) Measurements to demonstrate compliance with the conducted limits are not required for devices which only employ battery power for operation and which do not operate from the AC power lines or contain provisions for operation while connected to the AC power lines. Devices that include, or make provision for, the use of battery chargers which permit operating while charging, AC adaptors or battery eliminators or that connect to the AC power lines indirectly, obtaining their power through another device which is connected to the AC power lines, shall be tested to demonstrate compliance with the conducted limits. 4.2 Test Equipment Type Manufacturer/ Serial No. Last Calibration Next Calibration Model No. Receiver Rohde & Schwarz 825132/015 March 2000 March 2001 ESS (30 MHz - 1 GHz) V-LISN 50 Schwarzbeck 253 May 2000 May 2002 ohms//(50 µH + NNLA8119(mod) 5 ohms) (NSLK8127) 4.3 Test Procedures For tabletop equipment, the EUT is placed on a 1 meter by 1.5 meters wide and 0.8 meter high nonconductive table that is placed above the groundplane. Floor standing equipment is placed directly on the groundplane. Any supplemental grounding mechanisms are connected, if appropriate. The EUT is connected to its associated peripherals, with any excess I/O cabling bundled to approximately 1 meter. The EUT is connected to a dedicated LISN and all peripherals are connected to a second separate LISN circuit. The LISNs are bonded to the groundplane. Conducted measurements are made on each current carrying conductor with respect to ground. The EUT was tested as a tabletop equipment. During testing the receiver operated with and without its appropriate receive signal. The initial step in collecting conducted data is a peak scan of the measurement range with an EMI test receiver. The significant peaks are then measured with quasi-peak detector. Worst case conducted emissions are listed under chapter: test results. FCC_RPS435.DOC

FCC ID: LH8RP-S435 Test Report #EMCC-950295AOB Page 7 of 12 Issue Date: 2000-NOV-21 TEST OF CARDIN ELETTRONICA SPA S435 MODEL RPS435000.0US TO 47 CFR PART 15B - UNINTENTIONAL RADIATORS Conducted Emissions Test Characteristics Frequency range 0.45 MHz - 30.0 MHz Test instrumentation resolution bandwidth 9 kHz Lines Tested Line 1 (L) / Line 2 (N) 4.4 Test Results Device: Remote Control (RF) Superheterodyne Receiver for automatic opening systems Model: RPS435000.0US PRODUCT EMISSIONS QUASI PEAK DATA No Tested Emission Receiver Result Spec Margin Remarks Line Frequency Mode and Limit Bandwidth [MHz] [kHz] [dBµV] [dBµV] [dB] 1 L 10.055 9 / QP 22.3 48.0 25.7 all other emissions more than 30 dB below the limit Same results with and without appropriate receive signal. Judgment: The EUT meets the requirements of this section. Test Personnel: Reinhard Sauerschell Test Date: 2000-10-18 FCC_RPS435.DOC

FCC ID: LH8RP-S435 Test Report #EMCC-950295AOB Page 8 of 12 Issue Date: 2000-NOV-21 TEST OF CARDIN ELETTRONICA SPA S435 MODEL RPS435000.0US TO 47 CFR PART 15B - UNINTENTIONAL RADIATORS 5 RADIATED EMISSIONS TEST Test Requirement: FCC CFR47, Part 15B Test Procedure: ANSI C63.4:1992 5.1 Regulation Section 15.109 Radiated emission limits. (a) Except for Class A digital devices, the field strength of radiated emissions from unintentional radiators at a distance of 3 meters shall not exceed the following values: Frequency of Emission Field Strength (MHz) (microvolts/meter) 30 - 88 100 88 - 216 150 216 - 960 200 Above 960 500 (c) In the emission tables above, the tighter limits apply at the band edges. Sections 15.33 and 15.35 which specify the frequency range over which the radiated emissions are to be measured and the detector functions and other measurement standards apply. (f) For a receiver which employs terminals for the connection of an external receiving antenna, the receiver shall be tested to demonstrate compliance with the provisions of this Section with an antenna connected to the antenna terminals unless the antenna conducted power is measured as specified in Section 15.111(a). If a permanently attached receiving antenna is used, the receiver shall be tested to demonstrate compliance with the provisions of this Section. Section 15.33 Frequency range of radiated measurements: (b) For unintentional radiators: (1) Except as otherwise indicated in paragraphs (b)(2) or (b)(3), for an unintentional radiator, including a digital device, the spectrum shall be investigated from the lowest radio frequency signal generated or used in the device, without going below the lowest frequency for which a radiated emission limit is specified, up to the frequency shown in the following table: Highest frequency generated or used in the Upper frequency of measurement device or on which the range device operates (MHz) or tunes (MHz) Below 1.705 30 1.705 - 108 1000 108 - 500 2000 500 - 1000 5000 Above 1000 5th harmonic of the highest frequency or 40 GHz, whichever is lower FCC_RPS435.DOC

FCC ID: LH8RP-S435 Test Report #EMCC-950295AOB Page 9 of 12 Issue Date: 2000-NOV-21 TEST OF CARDIN ELETTRONICA SPA S435 MODEL RPS435000.0US TO 47 CFR PART 15B - UNINTENTIONAL RADIATORS (3) Except for a CB receiver, a receiver employing superheterodyne techniques shall be investigated from 30 MHz up to at least the second harmonic of the highest local oscillator frequency generated in the device. If such receiver is controlled by a digital device, the frequency range shall be investigated up to the higher of the second harmonic of the highest local oscillator frequency generated in the device or the upper frequency of the measurement range specified for the digital device in paragraph (b)(1) of this Section. Section 15.35 Measurement detector functions and bandwidths. (a) On any frequency or frequencies below or equal to 1000 MHz, the limits shown are based on measuring equipment employing a CISPR quasi-peak detector function and related measurement bandwidths, unless otherwise specified. (...) (b) On any frequency of frequencies above 1000 MHz, the radiated limits shown are based upon the use of measurement instrumentation employing an average detector function. When average radiated emission measurements are specified in the regulations, including emission measurements below 1000 MHz, there is also a limit on the radio frequency emissions, as measured using instrumentation with a peak detector function, corresponding to 20 dB above the maximum permitted average limit for the frequency being investigated unless a different peak emission limit is otherwise specified in the rules, e.g., see Section 15.255. Unless otherwise specified, measurements above 1000 MHz shall be performed using a minimum resolution bandwidth of 1 MHz. 5.2 Test Equipment Type Manufacturer/ Serial No. Last Calibration Next Calibration Model No. Receiver Rohde & Schwarz 825132/015 March 2000 March 2001 ESS (30 MHz - 1 GHz) Antenna EMCO 3143 9608-1316 Feb. 2000 Feb. 2001 (30 MHz - 1 GHz) Receiver Rohde & Schwarz June 2000 Dec. 2001 ESAI-D 833771/008 (1 GHz - 2 GHz) ESMI-RF 833827/002 ESMI-B1 832504/005 Antenna Schwarzbeck 137 Oct. 1999 Oct. 2001 (1 GHz - 2 GHz) BBHA 9120 D FCC_RPS435.DOC

FCC ID: LH8RP-S435 Test Report #EMCC-950295AOB Page 10 of 12 Issue Date: 2000-NOV-21 TEST OF CARDIN ELETTRONICA SPA S435 MODEL RPS435000.0US TO 47 CFR PART 15B - UNINTENTIONAL RADIATORS 5.3 Test Procedures For tabletop equipment, the EUT is placed on a 1 meter by 1.5 meters wide and 0.8 meter high nonconductive table that sits on a flush mounted metal turntable. Floor standing equipment is placed directly on the flush mounted metal turntable [Remark: Not applicable]. The EUT is connected to its associated peripherals with any excess I/O cabling bundled to approximately 1 meter [Remark: No peripherals connected]. Preview tests are performed to determine the "worst case" mode of operation. With the EUT operating in "worst case" mode, emissions from the unit are maximized by adjusting the polarization and height of the receive antenna and rotating the EUT on the turntable. Manipulating the system cables also maximizes EUT emissions. Radiated Emissions Test Characteristics Frequency range 30 MHz - 2,000 MHz Test distance 3m Test instrumentation resolution bandwidth 120 kHz (30 MHz - 1,000 MHz) 1 MHz (1,000 MHz - 2,000 MHz) Receive antenna scan height 1m-4m Receive antenna polarization Vertical/Horizontal 5.4 Field Strength Calculation The field strength is calculated by adding the Antenna Factor and Cable Factor. The basic equation with a sample calculation is as follows: FS = RA + AF + CF where FS = Field Strength in dB(µV/m) RA = Receiver Amplitude in dB(µV) AF = Antenna Factor in dB(1/m) CF = Cable Attenuation Factor in dB Assume a receiver reading of 23.5 dB(µV) is obtained. The Antenna Factor of 7.4 dB(1/m) and a Cable Factor of 1.1 dB are added, giving a field strength of 32 dB(µV/m). The 32 dB(µV/m) value can be mathematically converted to its corresponding level in µV/m. FS = 23.5 dB(µV) + 7.4 dB(1/m) + 1.1 dB = 32 dB(µV/m) FS = 10(32/20) µV/m = 39.8 µV/m FCC_RPS435.DOC

FCC ID: LH8RP-S435 Test Report #EMCC-950295AOB Page 11 of 12 Issue Date: 2000-NOV-21 TEST OF CARDIN ELETTRONICA SPA S435 MODEL RPS435000.0US TO 47 CFR PART 15B - UNINTENTIONAL RADIATORS 5.5 Test Results Device: Remote Control (RF) Superheterodyne Receiver for automatic opening systems Model: RPS435000.0US PRODUCT EMISSIONS No Emission Receiver Test Receiver Correction Result = Spec Antenna Polari- Margin Frequency Mode and Distance Reading Factor Corrected Limit Height zation Bandwidth Reading RA AF+CF FS ANT [MHz] [kHz] [m] [dB(µV)] [dB(1/m)] [dB(µV/m)] [dB(µV/m)] [m] [dB] 1 433.39 QP 120 3 13.5 20.5 34 46 1.00 v 12 2 1300 AV, 1000 3 4.3 26.8 31.1 54 1.00 h 22.9 Pk, 1000 3 15.6* 26.8 42.4* 54 + 20= 1.00 h 31.6 74 Same results with and without appropriate receive signal. Remark: * noise floor Judgment: The EUT meets the requirements of this section. Test Personnel: Reinhard Sauerschell Test Date: 2000-10-24 FCC_RPS435.DOC

FCC ID: LH8RP-S435 Test Report #EMCC-950295AOB Page 12 of 12 Issue Date: 2000-NOV-21 TEST OF CARDIN ELETTRONICA SPA S435 MODEL RPS435000.0US TO 47 CFR PART 15B - UNINTENTIONAL RADIATORS 6 MISCELLANEOUS COMMENTS AND NOTES None. 7 LIST OF ANNEXES Following annexes are separated parts to this test report. Description Pages Annex 1: Photographs of test setups 3 Annex 2: Photographs of equipment under test (EUT) 7 FCC_RPS435.DOC


Document Created: 2000-11-24 16:47:31
Document Modified: 2000-11-24 16:47:31
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC