Users Guide

FCC ID: LDK102107

Users Manual

Download: PDF
FCCID_3343696

GETTING STARTED GUIDE Cisco Aironet 1815T OfficeExtend Access Points First Published: February 2017

1 About this Guide 2 About the Access Point 3 Safety Instructions 4 Unpacking the AP 5 Ports and Connectors on the AP 6 Mounting and Powering the Access Point 7 Powering the Access Point 7 Configuring and Managing the AP 8 Checking the Access Point Status LED 9 Checking the Ethernet Port LEDs 10 Using the Mode Button 11 Related Documentation 12 Declarations of Conformity and Regulatory Information 13 Obtaining Documentation and Submitting a Service Request 2

1 About this Guide This guide provides instructions on how to install and configure your Cisco Aironet 1815T OfficeExtend access points. This guide also provides mounting instructions and limited troubleshooting procedures. The Aironet 1815T access point is referred to as access point or AP in this document. 2 About the Access Point The Cisco Aironet 1815T OfficeExtend access point is an 802.11 a/b/g/n/ac (Wave 2) access point, with internal antennas. You can place the access point horizontally on a desk. The AP supports 2.4 GHz 2x2 802.11b/g/n MU-MIMO and 5 GHz 2x2 802.11 a/n/ac (Wave 2) MU-MIMO applications simultaneously. The 1815T access point offers a highly secure enterprise wireless and wired connection to the home, micro-branch or other types of remote sites. This access point extends the corporate network to teleworkers, to mobile workers, or to micro-sites. The access point connects to the home or site broadband Internet access and establishes a highly secure tunnel to the corporate network. This tunnel allows remote employees access to data, voice, video, and cloud services for a mobility experience consistent with that at the corporate office. The Cisco Aironet 1815T access points support secure corporate data access and personal connectivity for teleworkers’ home devices with segmented home traffic. Access Point Features The features of the 1815T access points are: • Supported mode(s) of operation: – OfficeExtend Mode with hardware-based encryption • Radio features are: – Dual-radio, dual-band, 802.11ac Wave 2 – 2.4 GHz and 5 GHz concurrent radios – 2 GHz and 5 GHz radios with 2TX x 2RX and 2 spatial streams SU-MIMO and MU-MIMO. – 802.11ac based Transmit Beamforming – Quality of Service (QoS) – Radio Resource Management (RRM) 3

– Rogue Detection – BandSelect – Integrated Bluetooth LE 4.1 radio for location and asset tracking. • Real-time Service Extender which extends real-time services such as voice, wireless, video, and data to remote locations. • Datagram Transport Layer Security (DTLS) connection between the access point and the controller. • The AP supports the following hardware external interfaces: – Three 10/100/1000BASE-T ports (local Ethernet ports), one of which also serves as a PoE-Out port (PSE-LAN1 port). The PoE-Out port provides 802.3af Class 0 (15.4W) power. – One USB 2.0 port – DC power connector, for powering the AP using AIR-PWR-D=. – Mode button. For information on how to use the Mode button, see “Using the Mode Button” section on page 12. – One multi-color LED status indicator. See the “Checking the Access Point Status LED” section on page 10 for information on the colors of the LED status indicator. • Two integrated 2.4GHz/5GHz dual-band antennas located on the sides of the access point under the top housing. Peak antenna gain is approximately 2 dBi and 4 dBi in the 2.4 GHz and 5 GHz bands respectively. A full listing of the access point's features and specification are provided in the Cisco Aironet 1815T Access Point Data Sheet, at the following URL: (URL to be added later) Access Point Model Numbers and Regulatory Domains The Cisco Aironet 1815T access point models have the format AIR-1815T-x-K9. The ‘x’ in the model number is a placeholder for the regulatory domain. For information on supported regulatory domains, see the following page: http://www.cisco.com/go/aironet/compliance 4

3 Safety Instructions Translated versions of the following safety warnings are provided in the translated safety warnings document that is shipped with your access point. The translated warnings are also in the Translated Safety Warnings for Cisco Aironet Access Points, which is available on Cisco.com. Warning IMPORTANT SAFETY INSTRUCTIONS  This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071  SAVE THESE INSTRUCTIONS Warning Read the installation instructions before you connect the system to its power source. Statement 1004 Warning Installation of the equipment must comply with local and national electrical codes. Statement 1074 Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than:  20A. Statement 1005 Warning Do not operate your wireless network device near unshielded blasting caps or in an explosive environment unless the device has been modified to be especially qualified for such use. Statement 245B Caution This product and all interconnected equipment must be installed indoors within the same building, including the associated LAN connections as defined by Environment A of the IEEE 802.3af/at Standard. 5

Note Use only with listed Information Technology Equipment (ITE) equipment. For more information on ITE equipment, refer to article 645 of the latest National Electrical Code (NEC). 4 Unpacking the AP To unpack the access point, follow these steps: Step 1 Unpack and remove the access point and the mounting accessories, from the shipping box. Step 2 Return any packing material to the shipping container and save it for future use. Step 3 Verify that you have received the items listed below. If any item is missing or damaged, contact your Cisco representative or reseller for instructions. – The access point. – Cisco local power supply kit, with the AIR-PWR-D power adapter and power cord. The AIR-PWR-D power supply kit, containing the power adapter and the power cord can be also be separately ordered from Cisco. 6

5 Ports and Connectors on the AP Figure 1 Face of the AP 1 2 3 Location of the ports, connectors, Mode and 354939 Status LED on the face of the AP. 1 Power buttons, on the side of the AP. 2 Location of the Kensington lock slot on the 2 side of the AP. 7

Figure 2 AP Ports and Connectors POWER 354940 1 2 3 4 5 6 7 8 1 +48 VDC power port. 5 LAN port 3. 2 Power button. 6 WAN port. PSE / LAN port 1. USB port. This port provides 802.3af Power Sourcing Equipment (PSE) PoE-Out power on the LAN 1 Ethernet interface. When powered by AIR-PWR-C/D= the PoE-Out power is 3 802.3af Class 0 (15.4W). 7 4 LAN port 2. 8 Mode button. Note A physical security kit AIR-SEC-50=, which is sold separately, includes RJ-45 block-out plugs and two unlock keys using which you can restrict physical access to the Ethernet ports. Note All the three LAN ports support Auto-MDIX. The interface automatically detects the required cable connection type (straight through or crossover) and configures the connection appropriately. 8

6 Mounting and Powering the Access Point The access point can be placed/mounted in a horizontal position, on a horizontal surface such as a table. To ensure the best RF coverage for your access point, place your access point in an area as close to the wireless clients as possible and practical to do so. If the Internet source or gateway router is in a remote area, position your access point away from metal obstructions. Areas to avoid or places that may result in reduced range or performance are as follows. • In a basement of a multi-story home, as the signals must penetrate many walls. • Near large obstructions that can block the radio signals. Avoid areas like metal cabinets or refrigerators. • On the floor under a metal desk or other dense or conductive objects. The AP is powered using 44 to 57 VDC power via the VDC port, using Cisco Power Adapter AIR-PWR-D=. The PoE-Out port provides 802.3af Class 0 (15.4W) power. 9

7 Configuring and Managing the AP Detailed information on configuring and managing the AP is provided in the Cisco Aironet 1815T OfficeExtend Access Point User Guide, at the following URL: (URL to be added later) 8 Checking the Access Point Status LED The location of the access point status LED is shown in Figure 1 and Figure 2. For privacy, the status LED is automatically turned off when the access point joins a controller. Note Regarding LED status colors, it is expected that there will be small variations in color intensity and hue from unit to unit. This is within the normal range of the LED manufacturer’s specifications and is not a defect. The access point status LED indicates various conditions and are described in Table 1. Table 1 LED Status Indications Message Type LED State Possible Messages and Meanings Boot loader status Blinking Green DRAM memory test in progress sequence DRAM memory test OK Board initialization in progress Initializing flash file system Flash memory test OK Initializing Ethernet Ethernet OK Starting the operating system Initialization successful 10

Table 1 LED Status Indications (continued) Message Type LED State Possible Messages and Meanings Association status Chirping Green Normal operating condition. AP has joined to a controller, but no wireless client has associated with the AP. Chirping is short blips that look distinctly different from blinking. Green Normal operating condition. At least one wireless client association is present. Operating status Blinking Amber Software upgrade is in progress. Cycling through Green, Discovery/join process is in progress. Red and Amber Rapidly cycling Access point location command has been through Red, Green, invoked. Amber and Off Blinking Red Ethernet link is not operational. Boot loader warnings Blinking Amber Configuration recovery is in progress (Mode button pushed for 2 to 3 seconds). Red Ethernet failure. Image recovery has been initiated (Mode button pushed for 20 to 30 seconds). Blinking Green Image recovery is in progress (Mode button released after being kept pressed for 20 to 30 seconds). Boot loader errors Red DRAM memory test failure. Blinking Red and Flash file system failure. Amber Blinking Red and off Environment variable failure. Bad MAC address. Ethernet failure during image recovery. Boot environment failure. No Cisco image file. Boot failure. 11

Table 1 LED Status Indications (continued) Message Type LED State Possible Messages and Meanings Cisco AP OS errors Red Software failure. Try disconnecting and reconnecting power to the AP. Cycling through Red, General warning. Insufficient inline power. Green, Amber and off. 9 Checking the Ethernet Port LEDs Each Ethernet port has two LEDs for showing Link (Green) and Activity (Amber) statuses. They are integrated on the RJ45 connector. For a description of the statuses they indicate, see the following table. 10M 10M 100M 100M 1000M 1000M Link Active Link Active Link Active Link (Green) LED State Off Off Off Off On On Activity (Amber) LED State On Blinking On Blinking On Blinking 10 Using the Mode Button Using the Mode button you can: • Reset the AP to it’s default factory-shipped configuration. • Clear the AP’s internal storage, including all configuration files and the regulatory domain configuration. The Mode button is located on the back of the AP. You need to remove the back cover of the AP to access the mode button. To use the mode button, press, and keep pressed, the mode button on the access point during the AP's boot cycle. Wait until the AP's status LED changes to Amber. During this, the AP console shows a seconds counter, counting the number of seconds the mode button is pressed. Then: • To reset the AP to it’s default factory-shipped configuration, keep the mode button pressed for less than 20 seconds. The AP's configuration files are cleared. 12

This resets all configuration settings to factory defaults, including passwords, WEP keys, the IP address, and the SSID. However, the regulatory domain provisioning is not reset. • To clear the AP’s internal storage, including all configuration files and the regulatory domain configuration, keep the mode button pressed for more than 20 seconds, but less than 60 seconds. The AP's status LED changes from Amber to Red, and all the files in the AP's storage directory are cleared. This also removes any regulatory domain provisioning made previously and resets the AP back to -UX domain. If you keep the mode button pressed for more than 60 seconds, the mode button is assumed faulty and no changes are made. 11 Related Documentation All user documentation for the Cisco Aironet 1815T access point is available at the following URL: (URL to be added later) Wireless Controller Software support documentation is provided at: http://www.cisco.com/c/en/us/support/wireless/wireless-lan-controller-software/tsd-products-support -series-home.html For detailed information and guidelines for configuring and deploying your access point in a wireless network, see the following documentation: • Cisco Wireless LAN Controller Configuration Guide, Release 8.3, at the following URL: (URL to be added later) • Cisco Aironet 1815T Access Point Deployment Guide, at the following URL: (URL to be added later) 13

12 Declarations of Conformity and Regulatory Information This section provides declarations of conformity and regulatory information for the Cisco Aironet 1815T Access Points. You can find additional information at this URL: www.cisco.com/go/aironet/compliance Manufacturers Federal Communication Commission Declaration of Conformity Statement Tested To Comply With FCC Standards FOR HOME OR OFFICE USE Access Point Models Certification Number AIR-AP1815T-B-K9 LDK102107 Manufacturer: Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA This device complies with Part 15 rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and radiates radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference. However, there is no guarantee that 14

interference will not occur. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from which the receiver is connected. • Consult the dealer or an experienced radio/TV technician. Caution The Part 15 radio device operates on a non-interference basis with other devices operating at this frequency when using the integrated antennas. Any changes or modification to the product not expressly approved by Cisco could void the user’s authority to operate this device. VCCI Statement for Japan Warning This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual. 15

Guidelines for Operating Cisco Aironet Access Points in Japan This section provides guidelines for avoiding interference when operating Cisco Aironet access points in Japan. These guidelines are provided in both Japanese and English. Japanese Translation 208697 03-6434-6500 English Translation This equipment operates in the same frequency bandwidth as industrial, scientific, and medical devices such as microwave ovens and mobile object identification (RF-ID) systems (licensed premises radio stations and unlicensed specified low-power radio stations) used in factory production lines. 1. Before using this equipment, make sure that no premises radio stations or specified low-power radio stations of RF-ID are used in the vicinity. 2. If this equipment causes RF interference to a premises radio station of RF-ID, promptly change the frequency or stop using the device; contact the number below and ask for recommendations on avoiding radio interference, such as setting partitions. 3. If this equipment causes RF interference to a specified low-power radio station of RF-ID, contact the number below. Contact Number: 03-6434-6500 16

Statement 371—Power Cable and AC Adapter English Translation When installing the product, please use the provided or designated connection cables/power cables/AC adaptors. Using any other cables/adaptors could cause a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the use of UL-certified cables (that have the “UL” shown on the code) for any other electrical devices than products designated by CISCO. The use of cables that are certified by Electrical Appliance and Material Safety Law (that have “PSE” shown on the code) is not limited to CISCO-designated products. 17

Industry Canada Access Point Models Certification Number AIR-AP1815T-A-K9 2461B-102107 Canadian Compliance Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. This radio transmitter has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur. 18

Antenna Type Antenna Gain Antenna Impedance Dual-band Omni 2/3 dBi 50 ohms Operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. La bande 5 150-5 250 MHz est réservés uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux. Users are advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Les utilisateurs êtes avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la priorité) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. European Community, Switzerland, Norway, Iceland, and Liechtenstein Access Point Models: AIR-AP1815T-E-K9 19

Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC & Medical Directive 93/42/EEC 20

The following standards were applied: EMC—EN 301.489-1 v1.9.2; EN 301.489-17 v2.2.1 Health & Safety—EN60950-1: 2006; EN 50385: 2002 Radio—EN 300 328 v 1.8.1; EN 301.893 v 1.7.1 The conformity assessment procedure referred to in Article 10.4 and Annex III of Directive 1999/5/EC has been followed. 21

This device also conforms to the EMC requirements of the Medical Devices Directive 93/42/EEC. Note This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to certain frequencies and/or may require a license for operation. For more details, contact Cisco Corporate Compliance. The product carries the CE Mark: Declaration of Conformity for RF Exposure This section contains information on compliance with guidelines related to RF exposure. Generic Discussion on RF Exposure The Cisco products are designed to comply with the following national and international standards on Human Exposure to Radio Frequencies: • US 47 Code of Federal Regulations Part 2 Subpart J • American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers / IEEE C 95.1 (99) • International Commission on Non Ionizing Radiation Protection (ICNIRP) 98 • Ministry of Health (Canada) Safety Code 6. Limits on Human Exposure to Radio Frequency Fields in the range from 3kHz to 300 GHz • Australia Radiation Protection Standard To ensure compliance with various national and international Electromagnetic Field (EMF) standards, the system should only be operated with Cisco approved accessories. This Device Meets International Guidelines for Exposure to Radio Waves The 1815T access point device includes a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves (radio frequency electromagnetic fields) recommended by international guidelines. The guidelines were developed by an independent scientific organization (ICNIRP) and include a substantial safety margin designed to ensure the safety of all persons, regardless of age and health. 22

As such the systems are designed to be operated as to avoid contact with the antennas by the end user. It is recommended to set the system in a location where the antennas can remain at least a minimum distance as specified from the user in accordance to the regulatory guidelines which are designed to reduce the overall exposure of the user or operator. Separation Distance MPE Distance Limit 0.1 mW/cm 2 20 cm (7.87 inches) 1.00 mW/cm2 The World Health Organization has stated that present scientific information does not indicate the need for any special precautions for the use of wireless devices. They recommend that if you are interested in further reducing your exposure then you can easily do so by reorienting antennas away from the user or placing he antennas at a greater separation distance then recommended. This Device Meets FCC Guidelines for Exposure to Radio Waves The 1815T access point device includes a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves (radio frequency electromagnetic fields) as referenced in FCC Part 1.1310. The guidelines are based on IEEE ANSI C 95.1 (92) and include a substantial safety margin designed to ensure the safety of all persons, regardless of age and health. As such the systems are designed to be operated as to avoid contact with the antennas by the end user. It is recommended to set the system in a location where the antennas can remain at least a minimum distance as specified from the user in accordance to the regulatory guidelines which are designed to reduce the overall exposure of the user or operator. The device has been tested and found compliant with the applicable regulations as part of the radio certification process. Separation Distance MPE Distance Limit 0.1 mW/cm2 20 cm (7.87 inches) 1.00 mW/cm2 The US Food and Drug Administration has stated that present scientific information does not indicate the need for any special precautions for the use of wireless devices. The FCC recommends that if you are interested in further reducing your exposure then you can easily do so by reorienting antennas away from the user or placing the antennas at a greater separation distance then recommended or lowering the transmitter power output. 23

This Device Meets the Industry Canada Guidelines for Exposure to Radio Waves The 1815T access point device includes a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves (radio frequency electromagnetic fields) as referenced in Health Canada Safety Code 6. The guidelines include a substantial safety margin designed into the limit to ensure the safety of all persons, regardless of age and health. As such the systems are designed to be operated as to avoid contact with the antennas by the end user. It is recommended to set the system in a location where the antennas can remain at least a minimum distance as specified from the user in accordance to the regulatory guidelines which are designed to reduce the overall exposure of the user or operator. Separation Distance Frequency MPE Distance Limit 2 2 2.4 GHz 0.35 W/m 20 cm (7.87 inches) 5.4 W/m 5 GHz 0.91 W/m 2 9.2 W/m2 Health Canada states that present scientific information does not indicate the need for any special precautions for the use of wireless devices. They recommend that if you are interested in further reducing your exposure you can easily do so by reorienting antennas away from the user, placing the antennas at a greater separation distance than recommended, or lowering the transmitter power output. Cet appareil est conforme aux directives internationales en matière d'exposition aux fréquences radioélectriques Cet appareil de la gamme 1815T comprend un émetteur-récepteur radio. Il a été conçu de manière à respecter les limites en matière d'exposition aux fréquences radioélectriques (champs électromagnétiques de fréquence radio), recommandées dans le code de sécurité 6 de Santé Canada. Ces directives intègrent une marge de sécurité importante destinée à assurer la sécurité de tous, indépendamment de l'âge et de la santé. Par conséquent, les systèmes sont conçus pour être exploités en évitant que l'utilisateur n'entre en contact avec les antennes. Il est recommandé de poser le système là où les antennes sont à une distance minimale telle que précisée par l'utilisateur conformément aux directives réglementaires qui sont conçues pour réduire l'exposition générale de l'utilisateur ou de l'opérateur. 24

Distance d'éloignement Fréquence MPE Distance Limite 2 2 2.4 GHz 0.35 W/m 20 cm (7.87 inches) 5.4 W/m 5 GHz 0.91 W/m2 9.2 W/m2 Santé Canada affirme que la littérature scientifique actuelle n'indique pas qu'il faille prendre des précautions particulières lors de l'utilisation d'un appareil sans fil. Si vous voulez réduire votre exposition encore davantage, selon l'agence, vous pouvez facilement le faire en réorientant les antennes afin qu'elles soient dirigées à l'écart de l'utilisateur, en les plaçant à une distance d'éloignement supérieure à celle recommandée ou en réduisant la puissance de sortie de l'émetteur. Additional Information on RF Exposure You can find additional information on the subject at the following links: • Cisco Systems Spread Spectrum Radios and RF Safety white paper at this URL: http://www.cisco.com/warp/public/cc/pd/witc/ao340ap/prodlit/rfhr_wi.htm • FCC Bulletin 56: Questions and Answers about Biological Effects and Potential Hazards of Radio Frequency Electromagnetic Fields • FCC Bulletin 65: Evaluating Compliance with the FCC guidelines for Human Exposure to Radio Frequency Electromagnetic Fields You can obtain additional information from the following organizations: • World Health Organization Internal Commission on Non-Ionizing Radiation Protection at this URL: www.who.int/emf • United Kingdom, National Radiological Protection Board at this URL: www.nrpb.org.uk • Cellular Telecommunications Association at this URL: www.wow-com.com • The Mobile Manufacturers Forum at this URL: www.mmfai.org Administrative Rules for Cisco Aironet Access Points in Taiwan This section provides administrative rules for operating Cisco Aironet access points in Taiwan. The rules for all access points are provided in both Chinese and English. 25

tion At *# € kt §#h CR t Pwtik #t+olk EAUXAREBARARENENKHREER® iz > ad s 3%%%&%5%PB 6 # Pn &0 fokt# 4 %PRzlAc bt E+444 IiAFI#4RHHRERAEMALHREERRAERAAT #ARBW1G ; CRG#HA4 TUHH & > M Pri# Bo dAAEEATHEIHESA — m BAE > tGlk EferRAXItEX eA# E 12§xo« AI#RHH EMAAA RARmAT &LE ~ F14# 127n48 ASKHM TRtA Eit z+ 14# c

English Translation Administrative Rules for Low-power Radio-Frequency Devices Article 12 For those low-power radio-frequency devices that have already received a type-approval, companies, business units or users should not change its frequencies, increase its power or change its original features and functions. Article 14 The operation of the low-power radio-frequency devices is subject to the conditions that no harmful interference is caused to aviation safety and authorized radio station; and if interference is caused, the user must stop operating the device immediately and can't re-operate it until the harmful interference is clear. The authorized radio station means a radio-communication service operating in accordance with the Communication Act. The operation of the low-power radio-frequency devices is subject to the interference caused by the operation of an authorized radio station, by another intentional or unintentional radiator, by industrial, scientific and medical (ISM) equipment, or by an incidental radiator. Chinese Translation 27

English Translation Low-power Radio-frequency Devices Technical Specifications 4.7 Unlicensed National Information Infrastructure 4.7.5 Within the 5.25-5.35 GHz band, U-NII devices will be restricted to indoor operations to reduce any potential for harmful interference to co-channel MSS operations. 4.7.6 The U-NII devices shall accept any interference from legal communications and shall not interfere the legal communications. If interference is caused, the user must stop operating the device immediately and can't re-operate it until the harmful interference is clear. 4.7.7 Manufacturers of U-NII devices are responsible for ensuring frequency stability such that an emission is maintained within the band of operation under all conditions of normal operation as specified in the user manual. Operation of Cisco Aironet Access Points in Brazil This section contains special information for operation of Cisco Aironet access points in Brazil. Access Point Models: AIR-1815T-Z-K9 Figure 3 Brazil Regulatory Information 28

Portuguese Translation Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário. English Translation This equipment operates on a secondary basis and consequently must accept harmful interference, including interference from stations of the same kind. This equipment may not cause harmful interference to systems operating on a primary basis. Declaration of Conformity Statements All the Declaration of Conformity statements related to this product can be found at the following location: http://www.ciscofax.com 13 Obtaining Documentation and Submitting a Service Request For information on obtaining documentation, using the Cisco Bug Search Tool (BST), submitting a service request, and gathering additional information, see What’s New in Cisco Product Documentation. To receive new and revised Cisco technical content directly to your desktop, you can subscribe to the What’s New in Cisco Product Documentation RSS feed. The RSS feeds are a free service. © 2017 Cisco Systems, Inc. All rights reserved. Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R) 29


Document Created: 2017-12-28 22:47:28
Document Modified: 2017-12-28 22:47:28
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC