MPE_5470_5725_Test_Report

FCC ID: LDK102084

RF Exposure Info

Download: PDF
FCCID_1780676

Custom EMC Test Report No: EDCS - 1186224 Maximum Permissible Exposure (MPE) Calculations 15.407: U-NII devices are subject to the radio frequency radiation exposure requirements specified in Sec. 1.1307(b), Sec. 2.1091 and Sec. 2.1093 of this chapter, as appropriate. All equipment shall be considered to operate in a ``general population/uncontrolled'' environment. Applications for equipment authorization of devices operating under this section must contain a statement confirming compliance with these requirements for both fundamental emissions and unwanted emissions. Technical information showing the basis for this statement must be submitted to the Commission upon request. Given E=√(30*P*G)/d and S=E^2/3770 where E=Field Strength in Volts/meter P=Power in Watts G=Numeric Antenna Gain d=Distance in meters S=Power Density in mW/cm^2 Combine equations and rearrange the terms to express the distance as a function of the remaining variables: d=√((30*P*G)/(3770*S)) Changing to units of power in mW and distance in cm, using: P(mW)=P(W)/1000 d(cm)=100*d(m) yields d=100*√((30*(P/1000)*G)/(3770*S)) d=0.282*√(P*G/S) where d=Distance in cm P=Power in mW G=Numerica Antenna Gain S=Power Density in mW/cm^2 Substituting the logarithmic form of power and gain using: P(mW)=10^(P(dBm)/10) G(numeric)=10^(G(dBi)/10) yields d=0.282*10^((P+G)/20)/√S Equation (1) and s=((0.282*10^((P+G)/20))/d)^2 Equation (2) where d=MPE distance in cm P=Power in dBm G=Antenna Gain in dBi S=Power Density in mW/cm^2 Page No: 78 of 80 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential

Custom EMC Test Report No: EDCS - 1186224 Equation (1) and the measured peak power are used to calculate the MPE distance. Note that for mobile or fixed location transmitters such as an access point, the minimum separation distance is 20 cm even if the calculations indicate that the MPE distance may be less. S=1mW/cm^2 maximum. The highest supported antenna gain is 6 dBi (9dBi with beamforming). Using the peak power levels recorded in the test report along with Equation 1 above, the MPE distances are calculated as follows. Peak Power Transmit Antenna MPE Frequency Bit Rate Density Power Gain Distance Limit Margin (MHz) (Mbps) (mW/cm^2) (dBm) (dBi) (cm) (cm) (cm) 5500 54 1 18.7 6 4.84 20 15.16 5580 54 1 17.0 6 3.98 20 16.02 5700 54 1 18.6 6 4.79 20 15.21 MPE Calculations To maintain compliance, installations will assure a separation distance of at least 20cm. Using Equation 2, the MPE levels (s) at 20 cm are calculated as follows: Peak MPE Transmit Antenna Power Frequency Bit Rate Distance Power Gain Density Limit Margin (MHz) (Mbps) (cm) (dBm) (dBi) (mW/cm^2) (mW/cm^2) (mW/cm^2) 5500 54 20 18.7 6 0.06 1 0.94 5580 54 20 17.0 6 0.04 1 0.96 5700 54 20 18.6 6 0.06 1 0.94 Page No: 79 of 80 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential


Document Created: 2012-08-31 10:08:16
Document Modified: 2012-08-31 10:08:16
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC