Test Rpt (Co-located)_LDK-TEI301W

FCC ID: LDK-TEI301W

Test Report

Download: PDF
FCCID_1456445

Supplemental “Transmit Simultaneously” Test Report REPORT NO.: RF991006E02-2 R1 MODEL NO.: TEI301W-xx, REN301W-xx, TES301W-xx FCC ID: LDK-TEI301W IC ID: 2461B-TEI301W RECEIVED: Oct. 06, 2010 TESTED: Oct. 14 to 26, 2010 ISSUED: Feb. 09, 2011 APPLICANT: Cisco Systems Inc. 170 West Tasman Drive, San Jose, CA 95134-1706, ADDRESS: USA. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS: No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan This test report consists of 27 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by any government agencies. The test results in the report only apply to the tested sample. Report No.: RF991006E02-2 R1 1 Report Format Version 3.0.1 Cancels and replaces the report No.: RF991006E02-2 dated Jan. 18, 2011

Table of Contents RELEASE CONTROL RECORD................................................................................. 3 1 CERTIFICATION ........................................................................................... 4 2 SUMMARY OF TEST RESULTS ................................................................... 5 2.1 MEASUREMENT UNCERTAINTY ...........................................................................5 3 GENERAL INFORMATION............................................................................ 6 3.1 GENERAL DESCRIPTION OF EUT ........................................................................6 3.2 DESCRIPTION OF TEST MODES ..........................................................................9 3.3 TEST MODE APPLICABLITY AND TESTED CHANNEL DETAIL: .........................10 3.4 DESCRIPTION OF SUPPORT UNITS...................................................................12 3.5 CONFIGURATION OF SYSTEM UNDER TEST ....................................................13 4 TEST TYPES AND RESULTS ..................................................................... 14 4.1 CONDUCTED EMISSION MEASUREMENT .........................................................14 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ............................ 14 4.1.2 TEST INSTRUMENTS................................................................................. 14 4.1.3 TEST PROCEDURES ................................................................................. 15 4.1.4 DEVIATION FROM TEST STANDARD........................................................ 15 4.1.5 TEST SETUP .............................................................................................. 15 4.1.6 EUT OPERATING CONDITIONS ................................................................ 16 4.1.7 TEST RESULTS .......................................................................................... 17 4.2 RADIATED EMISSION MEASUREMENT ..............................................................19 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT ................................. 19 4.2.2 TEST INSTRUMENTS................................................................................. 20 4.2.3 TEST PROCEDURES ................................................................................. 22 4.2.4 TEST SETUP .............................................................................................. 23 4.2.5 EUT OPERATING CONDITIONS ................................................................ 23 4.2.6 TEST RESULTS .......................................................................................... 24 4.2.7 TEST RESULTS .......................................................................................... 25 5 INFORMATION ON THE TESTING LABORATORIES ................................ 26 6 APPENDIX A - MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB ...................................................... 27 Report No.: RF991006E02-2 R1 2 Report Format Version 3.0.1 Cancels and replaces the report No.: RF991006E02-2 dated Jan. 18, 2011

RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED Original release NA Jan. 18, 2011 RF991006E02-2 R1 Modified the product name of the EUT Feb. 09, 2011 Report No.: RF991006E02-2 R1 3 Report Format Version 3.0.1 Cancels and replaces the report No.: RF991006E02-2 dated Jan. 18, 2011

1 CERTIFICATION PRODUCT : IP Managed Services Home Gateway BRAND NAME : Cisco MODEL NO. : TEI301W-xx, REN301W-xx, TES301W-xx TESTED : Oct. 14 to 26, 2010 APPLICANT : Cisco Systems Inc. TEST SAMPLE : MASS-PRODUCTION STANDARDS : FCC Part 15, Subpart C (Section 15.247) ANSI C63.4-2003 Canada RSS-210 issue 7 Canada RSS-Gen issue 2 The above equipment (Model: TEI301W-NA) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE: Feb. 09, 2011 ( Midoli Peng, Specialist ) TECHNICAL ACCEPTANCE : , DATE: Feb. 09, 2011 ( Hank Chung, Deputy Manager ) APPROVED BY : , DATE: Feb. 09, 2011 (May Chen, Deputy Manager ) Note: Per a request of the FCC, the IP Managed Services Home Gateway was tested for conducted emissions and radiated emissions in restricted bands while transmitting on both WLAN and Zwave at simultaneously. Report No.: RF991006E02-2 R1 4 Report Format Version 3.0.1 Cancels and replaces the report No.: RF991006E02-2 dated Jan. 18, 2011

2 SUMMARY OF TEST RESULTS The EUT has been tested according to the following specifications: APPLIED STANDARD: FCC Part 15, Subpart C Standard Test Type and Limit Result REMARK Section Meet the requirement of limit. Minimum passing 15.207 AC Power Conducted Emission PASS margin is -14.85dB at 0.181MHz Meet the requirement of Transmitter Radiated Emissions limit Minimum passing 15.247(d) PASS Limit: Table 15.209 margin is -1.7 dB at 40.30 MHz 2.1 MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2: This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. Measurement Value Conducted emissions 2.45 dB Radiated emissions (30MHz-1GHz) 3.76 dB Radiated emissions (1GHz -18GHz) 2.19 dB Radiated emissions (18GHz -40GHz) 2.55 dB Report No.: RF991006E02-2 R1 5 Report Format Version 3.0.1 Cancels and replaces the report No.: RF991006E02-2 dated Jan. 18, 2011

3 GENERAL INFORMATION 3.1 GENERAL DESCRIPTION OF EUT PRODUCT IP Managed Services Home Gateway MODEL NO. TEI301W-xx, REN301W-xx, TES301W-xx FCC ID LDK-TEI301W IC ID 2461B-TEI301W POWER SUPPLY DC 12V from power adapter For WLAN : CCK, DQPSK, DBPSK for DSSS MODULATION TYPE 64QAM, 16QAM, QPSK, BPSK for OFDM For Zwave : FSK MODULATION For WLAN : DSSS, OFDM TECHNOLOGY For Zwave : FSK For WLAN : 802.11b: 11 / 5.5 / 2 / 1Mbps 802.11g: 54 / 48 / 36 / 24 / 18 / 12 / 9 / 6Mbps 802.11n (20MHz, 800ns GI): 65 / 58.5 / 52 / 39 / 26 / 19.5 / 13 / 6.5Mbps 802.11n (40MHz, 800ns GI): 135 / 121.5 / 108 / 81 / 54 / 40.5 / 27 / TRANSFER RATE 13.5Mbps 802.11n (20MHz, 400ns GI): 72.2 / 65 / 57.8 / 43.3 / 28.9 / 21.7 / 14.4 / 7.2Mbps 802.11n (40MHz, 400ns GI): 150 / 135 / 120 / 90 / 60 / 45 / 30 / 15Mbpss For Zwave : 9.6 kbps and 40 kbps For WLAN :2412MHz ~ 2462MHz FREQUENCY RANGE For Zwave : 908.42MHz For WLAN : 11 for 802.11b, 802.11g, 802.11n (20MHz) NUMBER OF CHANNEL 7 for 802.11n (40MHz) For Zwave : 1 For WLAN : 802.11b: 151.4mW MAXIMUM OUTPUT 802.11g: 338.8mW POWER 802.11n (20MHz): 625.3mW 802.11n (40MHz): 296.5mW For Zwave : NA ANTENNA TYPE Please see note 3 DATA CABLE NA Report No.: RF991006E02-2 R1 6 Report Format Version 3.0.1 Cancels and replaces the report No.: RF991006E02-2 dated Jan. 18, 2011

For models : TEI301W-xx, TES301W-xx USB port x 2 (USB 2.0) Ethernet port x 4 (Ethernet (10,100,1000Mbps)) Internet port x 1 (Internet (10,100,1000Mbps)) I/O PORTS PHONE port x 2 For model : REN301W-xx USB port x 2 (USB 2.0) Ethernet port x 4 (Ethernet (10,100,1000Mbps)) Internet port x 1 (Internet (10,100,1000Mbps)) ASSOCIATED DEVICES Adapter x 1 1. There are Zwave technology and WLAN technology used for the EUT. 2. The EUT has below model names as the following table: Add Function-1 Add Function-2 Add Function-3 Model No. Basic Function FXS x 2ch SIM controller Internal Zwave REN301W-xx Yes - - Yes TES301W-xx Yes Yes - Yes TEI301W-xx Yes Yes Yes Yes Note : The “ xx ” of Model Names could be 0~9, A~Z, a~z or blank. The EUT was pre-tested with above models, the worse case was found in the model: TEI301W-NA. Therefore only the test data of the model was recorded in this report. 3. There are three antennas provided to this EUT, please refer to the following table: For WLAN Cable Antenna Antenna Antenna Cable Net Gain Frequency range No. Length Type Connector Gain (dBi) loss(dB) (dBi) (GHz) (cm) 1 PIFA I-PEX 3 1 2 26 2.4~2.5 2 PIFA I-PEX 3 1 2 21 2.4~2.5 For Zwave Frequency range No. Antenna Type Antenna Connector Antenna Gain (dBi) (MHz) 3 chip NA -4 902~928 Report No.: RF991006E02-2 R1 7 Report Format Version 3.0.1 Cancels and replaces the report No.: RF991006E02-2 dated Jan. 18, 2011

4. The EUT must be supplied with a power adapter and following two different model names could be chosen: Adapter Brand Model No. Spec. AC Input: 100-240V, 50/60Hz, 1A AC input cable(Unshielded, 0.3m) Adapter 1 DELTA EADP-30RB A DC Output: 12V, 2.5A DC Output cable(Unshielded, 1.5m) AC Input: 100-240V, 50-60Hz, 0.6A Adapter 2 PHIHONG PSA24A-120 DC Output: 12V, 2.0A DC Output cable(Unshielded, 1.5m) 5. The EUT was pre-tested under the following modes: Test Mode Description Mode A Level-set + adapter 1 Mode B Tower-set + adapter 1 Mode C Level-set + adapter 2 For radiated test the worst case was found in Mode C. Therefore only the test data of the modes were recorded in this report. 6. The above EUT information was declared by manufacturer and for more detailed features description, please refer to the manufacturer's specifications or user's manual. Report No.: RF991006E02-2 R1 8 Report Format Version 3.0.1 Cancels and replaces the report No.: RF991006E02-2 dated Jan. 18, 2011

3.2 DESCRIPTION OF TEST MODES For WLAN : Eleven channels are provided for 802.11b, 802.11g, 802.11n (20MHz): CHANNEL FREQUENCY CHANNEL FREQUENCY 1 2412MHz 7 2442MHz 2 2417MHz 8 2447MHz 3 2422MHz 9 2452MHz 4 2427MHz 10 2457MHz 5 2432MHz 11 2462MHz 6 2437MHz Seven channels are provided for 802.11n (40MHz): CHANNEL FREQUENCY CHANNEL FREQUENCY 1 2422MHz 5 2442MHz 2 2427MHz 6 2447MHz 3 2432MHz 7 2452MHz 4 2437MHz For Zwave: One channel is provided to this EUT. CHANNEL FREQUENCY 1 908.42 Report No.: RF991006E02-2 R1 9 Report Format Version 3.0.1 Cancels and replaces the report No.: RF991006E02-2 dated Jan. 18, 2011

3.3 TEST MODE APPLICABLITY AND TESTED CHANNEL DETAIL: EUT Applicable to configure Description mode PLC RE<1G RE³1G A √ √ √ Co-located mode with adapter 2 Where PLC: Power Line Conducted Emission RE<1G RE: Radiated Emission below 1GHz RE³1G: Radiated Emission above 1GHz APCM: Antenna Port Conducted Measurement Note1: Pre-Scan has been conducted to determine the worst case mode from antenna power. Note2: The worst card was found in U727 (Channel Frequency: 1880MHz). POWER LINE CONDUCTED EMISSION TEST:  Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. Available Tested Modulation Modulation Mode Channel Channel Technology Type 1 to 11 6 OFDM BPSK WLAN + Zwave 1 1 FSK FSK Radiated Emission Test (Below 1 GHz):  Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. Available Tested Modulation Modulation Mode Channel Channel Technology Type 1 to 11 6 OFDM BPSK WLAN + Zwave 1 1 FSK FSK Radiated Emission Test (Above 1 GHz):  Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. Available Tested Modulation Modulation Mode Channel Channel Technology Type 1 to 11 6 OFDM BPSK WLAN + Zwave 1 1 FSK FSK Report No.: RF991006E02-2 R1 10 Report Format Version 3.0.1 Cancels and replaces the report No.: RF991006E02-2 dated Jan. 18, 2011

TEST CONDITION: APPLICABLE TO ENVIRONMENTAL CONDITIONS INPUT POWER (SYSTEM) TESTED BY RE³1G 25deg. C, 73%RH, 1013 hPa 120Vac, 60Hz Rex Huang RE<1G 21deg. C, 70%RH, 1013 hPa 120Vac, 60Hz Eric Lee PLC 28deg. C, 76%RH, 1013 hPa 120Vac, 60Hz Timmy Hu Report No.: RF991006E02-2 R1 11 Report Format Version 3.0.1 Cancels and replaces the report No.: RF991006E02-2 dated Jan. 18, 2011

3.4 DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. No. Product Brand Model No. Serial No. FCC ID NOTEBOOK 1 DELL PP27L 6YLB32S FCC DoC COMPUTER 2 TELEPHONE WONDER WD-303 6C17FA00515 NA 3 TELEPHONE WONDER WD-303 6C17FA00681 NA 4 iPod Apple A1199 6U6426MTVQS FCC DoC 5 iPod Apple A1199 6U6425Z8VQ5 FCC DoC 6 ROUTER Cisco E1000 NA NA No. Signal cable description 1 10m UTP cable. 2 1m RJ-11 cable. 3 1m RJ-11 cable. 4 1m USB cable. 5 1m USB cable. 6 10m UTP cable. Note: The power cords of the above support units were unshielded (1.8m).2 Report No.: RF991006E02-2 R1 12 Report Format Version 3.0.1 Cancels and replaces the report No.: RF991006E02-2 dated Jan. 18, 2011

3.5 CONFIGURATION OF SYSTEM UNDER TEST USB cable (1m) USB cable (1m) Adapter 4. iPod 5. iPod EUT (on the test table) RJ-11 cable (1m) 3. TELEPHONE TEST TABLE 3. TELEPHONE UTP cable (10m) UTP cable (10m) UTP cable (10m) x3 1. NOTEBOOK 6. ROUTER Load COMPUTER CONTROL ROOM Report No.: RF991006E02-2 R1 13 Report Format Version 3.0.1 Cancels and replaces the report No.: RF991006E02-2 dated Jan. 18, 2011

4 TEST TYPES AND RESULTS 4.1 CONDUCTED EMISSION MEASUREMENT 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT FREQUENCY OF EMISSION (MHz) CONDUCTED LIMIT (dBµV) Quasi-peak Average 0.15-0.5 66 to 56 56 to 46 0.5-5 56 46 5-30 60 50 NOTE: 1. The lower limit shall apply at the transition frequencies. 2. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50 MHz. 3. All emanations from a class A/B digital device or system, including any network of conductors and apparatus connected thereto, shall not exceed the level of field strengths specified above. 4.1.2 TEST INSTRUMENTS Test date: Oct. 14, 2010 DESCRIPTION & CALIBRATED CALIBRATED MODEL NO. SERIAL NO. MANUFACTURER DATE UNTIL Test Receiver ESCS 30 100375 Mar. 09, 2010 Mar. 08, 2011 Line-Impedance Stabilization Network NSLK 8127 8127-522 Sep. 08, 2010 Sep. 07, 2011 (for EUT) Line-Impedance Stabilization Network ESH3-Z5 848773/004 Oct. 26, 2009 Oct. 25, 2010 (for Peripheral) RF Cable (JYEBAO) 5DFB COBCAB-001 Nov. 24, 2009 Nov. 23, 2010 50 ohms Terminator 50 3 Oct. 28, 2009 Oct. 27, 2010 BV Software NA NA NA ADT_Cond_V7.3.7 Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in Shielded Room No. C. 3 The VCCI Con C Registration No. is C-3611. Report No.: RF991006E02-2 R1 14 Report Format Version 3.0.1 Cancels and replaces the report No.: RF991006E02-2 dated Jan. 18, 2011

4.1.3 TEST PROCEDURES a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 ohm/ 50uH of coupling impedance for the measuring instrument. b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. c. The frequency range from 150kHz to 30MHz was searched. Emission levels under (Limit - 20dB) were not recorded. 4.1.4 DEVIATION FROM TEST STANDARD No deviation 4.1.5 TEST SETUP V e r tic a l G r o u n d R e f e r e n c e P la n e T e s t R e c e iv e r EUT 40cm 80cm L IS N H o r iz o n t a l G r o u n d R e fe r e n c e P la n e N o t e : 1 .S u p p o r t u n its w e r e c o n n e c te d to s e c o n d L IS N . 2 .B o t h o f L IS N s (A M N ) a r e 8 0 c m fr o m E U T a n d a t le a s t 8 0 fr o m o th e r u n its a n d o th e r m e ta l p la n e s For the actual test configuration, please refer to the related item – Photographs of the Test Configuration. Report No.: RF991006E02-2 R1 15 Report Format Version 3.0.1 Cancels and replaces the report No.: RF991006E02-2 dated Jan. 18, 2011

4.1.6 EUT OPERATING CONDITIONS 1. Prepared other computer systems (support units 1, 6) to act as communication partners and placed them outside of testing area. 2. The communication partners ran test programs “WiFi Boardcom wl command” and “Zwave Telent command” to enable EUT under transmission/receiving condition continuously via UTP cables. 3. Support unit 1 (NB) read music file from Support units 4~5 (iPod) and played it via EUT. Report No.: RF991006E02-2 R1 16 Report Format Version 3.0.1 Cancels and replaces the report No.: RF991006E02-2 dated Jan. 18, 2011

4.1.7 TEST RESULTS PHASE Line (L) 6dB BANDWIDTH 9 kHz Emission Freq. Corr. Reading Value Limit Margin Level No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.181 9.73 39.84 - 49.57 - 64.42 54.42 -14.85 - 2 0.302 9.75 33.77 - 43.52 - 60.17 50.17 -16.66 - 3 0.424 9.75 29.64 - 39.39 - 57.38 47.38 -17.99 - 4 0.634 9.75 26.44 - 36.19 - 56.00 46.00 -19.81 - 5 0.830 9.76 24.73 - 34.49 - 56.00 46.00 -21.51 - 6 2.996 9.78 24.38 - 34.16 - 56.00 46.00 -21.84 - REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. "-": The Quasi-peak reading value also meets average limit and measurement with the average detector is unnecessary. 3. The emission levels of other frequencies were very low against the limit. 4. Margin value = Emission level - Limit value 5. Correction factor = Insertion loss + Cable loss 6. Emission Level = Correction Factor + Reading Value. Report No.: RF991006E02-2 R1 17 Report Format Version 3.0.1 Cancels and replaces the report No.: RF991006E02-2 dated Jan. 18, 2011

PHASE Neutral (N) 6dB BANDWIDTH 9 kHz Emission Freq. Corr. Reading Value Limit Margin Level No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.173 9.73 33.72 - 43.45 - 64.82 54.82 -21.37 - 2 0.248 9.74 30.11 - 39.85 - 61.83 51.83 -21.98 - 3 0.904 9.76 23.35 - 33.11 - 56.00 46.00 -22.89 - 4 1.797 9.77 23.77 - 33.54 - 56.00 46.00 -22.46 - 5 2.660 9.78 24.52 - 34.30 - 56.00 46.00 -21.70 - 6 3.812 9.81 25.24 - 35.05 - 56.00 46.00 -20.95 - REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. "-": The Quasi-peak reading value also meets average limit and measurement with the average detector is unnecessary. 3. The emission levels of other frequencies were very low against the limit. 4. Margin value = Emission level - Limit value 5. Correction factor = Insertion loss + Cable loss 6. Emission Level = Correction Factor + Reading Value. Report No.: RF991006E02-2 R1 18 Report Format Version 3.0.1 Cancels and replaces the report No.: RF991006E02-2 dated Jan. 18, 2011

4.2 RADIATED EMISSION MEASUREMENT 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT Emissions radiated outside of the specified bands, shall be according to the general radiated limits in 15.209 as following: Frequencies Field strength Measurement distance (meters) (MHz) (microvolts/meter) 0.009-0.490 2400/F(kHz) 300 0.490-1.705 24000/F(kHz) 30 1.705-30.0 30 30 30-88 100 3 88-216 150 3 216-960 200 3 Above 960 500 3 NOTE: 1. The lower limit shall apply at the transition frequencies. 2. Emission level (dBuV/m) = 20 log Emission level (uV/m). 3. As shown in 15.35(b), for frequencies above 1000MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20dB under any condition of modulation. Report No.: RF991006E02-2 R1 19 Report Format Version 3.0.1 Cancels and replaces the report No.: RF991006E02-2 dated Jan. 18, 2011

4.2.2 TEST INSTRUMENTS For below 1GHz test: Test date: Oct. 26, 2010 DESCRIPTION & CALIBRATED CALIBRATED MODEL NO. SERIAL NO. MANUFACTURER DATE UNTIL Agilent E4446A MY48250253 Aug. 23, 2010 Aug. 22, 2011 Spectrum Analyzer Agilent N9039A MY46520310 Aug. 23, 2010 Aug. 22, 2011 Pre-Selector Agilent N5181A MY49060347 July 30, 2010 July 29, 2011 Signal Generator LIG NEX1 ER-265 L09068005 Oct. 25, 2010 Oct. 24, 2011 Test Receiver Mini-Circuits ZFL-1000VH2B AMP-ZFL-04 Nov. 18, 2009 Nov. 17, 2010 Pre-Amplifier Agilent Pre-Amplifier 8449B 3008A02465 Mar. 01, 2010 Feb. 28, 2011 Miteq AFS33-1800265 881786 NA NA Pre-Amplifier 0-30-8P-44 SCHWARZBECK VULB 9168 9168-361 Apr. 28, 2010 Apr. 27, 2011 Trilog Broadband Antenna AISI AIH.8018 0000220091110 Nov. 16, 2009 Nov. 15, 2010 Horn_Antenna SCHWARZBECK BBHA 9170 9170-424 Oct. 08, 2010 Oct. 07, 2011 Horn_Antenna RF104-205 RF CABLE NA RF104-207 Dec. 24, 2009 Dec. 23, 2010 RF104-208 RF Cable NA CHHCAB_001 NA NA ADT_Radiated_ Software NA NA NA V8.7.05 CT Antenna Tower & NA NA NA NA Turn Table Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The horn antenna, preamplifier (model: 8449B) are used only for the measurement of emission frequency above 1GHz if tested. 3. The test was performed in 966 Chamber No. H. 4. The FCC Site Registration No. is 797305. 5. The CANADA Site Registration No. is IC 7450H-3. Report No.: RF991006E02-2 R1 20 Report Format Version 3.0.1 Cancels and replaces the report No.: RF991006E02-2 dated Jan. 18, 2011

For above 1GHz test: DESCRIPTION & CALIBRATED CALIBRATED MODEL NO. SERIAL NO. MANUFACTURER DATE UNTIL Agilent E4446A MY48250254 July 14, 2010 July 13, 2011 Spectrum Analyzer Agilent N9039A MY46520311 July 14, 2010 July 13, 2011 Pre-Selector Agilent N5181A MY49060517 July 14, 2010 July 13, 2011 Signal Generator Mini-Circuits ZFL-1000VH2B AMP-ZFL-03 Nov. 18, 2009 Nov. 17, 2010 Pre-Amplifier Agilent Pre-Amplifier 8449B 3008A02578 July 05, 2010 July 04, 2011 Miteq AFS33-1800265 881786 NA NA Pre-Amplifier 0-30-8P-44 SCHWARZBECK VULB 9168 9168-360 Apr. 29, 2010 Apr. 28, 2011 Trilog Broadband Antenna AISI 000032009111 AIH.8018 Nov. 16, 2009 Nov. 15, 2010 Horn_Antenna 0 SCHWARZBECK BBHA 9170 9170-424 Oct. 08, 2010 Oct. 07, 2011 Horn_Antenna RF104-201 RF CABLE NA RF104-203 Dec. 24, 2009 Dec. 23, 2010 RF104-204 RF Cable NA CHGCAB_001 NA NA ADT_Radiated_ Software NA NA NA V8.7.05 CT Antenna Tower & NA NA NA NA Turn Table Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The horn antenna, preamplifier (model: 8449B) are used only for the measurement of emission frequency above 1GHz if tested. 3. The test was performed in 966 Chamber No. G. 4. The FCC Site Registration No. is 966073. 5. The VCCI Site Registration No. is G-137. 6. The CANADA Site Registration No. is IC 7450H-2. Report No.: RF991006E02-2 R1 21 Report Format Version 3.0.1 Cancels and replaces the report No.: RF991006E02-2 dated Jan. 18, 2011

4.2.3 TEST PROCEDURES a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meters chamber. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The antenna is a broadband antenna, and its height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. f. If the emission level of the EUT in peak mode was 10 dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10 dB margin would be re-tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet. NOTE: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for Quasi-peak detection (QP) at frequency below 1GHz. 2. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 1 MHz for Peak detection at frequency above 1GHz. 3. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is 10 Hz for Average detection (AV) at frequency above 1GHz. Report No.: RF991006E02-2 R1 22 Report Format Version 3.0.1 Cancels and replaces the report No.: RF991006E02-2 dated Jan. 18, 2011

4.2.4 TEST SETUP Test Receiver For the actual test configuration, please refer to the related item – Photographs of the Test Configuration. 4.2.5 EUT OPERATING CONDITIONS Same as 4.1.6 Report No.: RF991006E02-2 R1 23 Report Format Version 3.0.1 Cancels and replaces the report No.: RF991006E02-2 dated Jan. 18, 2011

4.2.6 TEST RESULTS BELOW 1GHz WORST-CASE DATA： EUT TEST CONDITION MEASUREMENT DETAIL INPUT POWER 120Vac, 60 Hz FREQUENCY RANGE 30-1000 MHz ENVIRONMENTAL 21deg. C, 70%RH DETECTOR Peak (PK) CONDITIONS 1013hPa FUNCTION Average (AV) TESTED BY Eric Lee ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION TABLE CORRECTION LIMIT ANTENNA RAW VALUE NO. FREQ. (MHz) LEVEL MARGIN (dB) ANGLE FACTOR (dBuV/m) HEIGHT (m) (dBuV) (dBuV/m) (Degree) (dB/m) 1 164.29 35.7 QP 43.5 -7.8 1.50 H 43 21.62 14.09 2 198.40 37.9 QP 43.5 -5.6 1.50 H 299 26.53 11.33 3 250.03 40.3 QP 46.0 -5.7 1.00 H 80 27.33 12.95 4 374.97 35.5 QP 46.0 -10.5 1.00 H 53 18.34 17.18 5 843.80 38.0 QP 46.0 -8.0 2.00 H 345 12.19 25.82 6 875.06 38.2 QP 46.0 -7.8 1.00 H 141 11.88 26.29 7 937.47 40.3 QP 46.0 -5.7 1.50 H 0 13.42 26.91 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION TABLE CORRECTION LIMIT ANTENNA RAW VALUE NO. FREQ. (MHz) LEVEL MARGIN (dB) ANGLE FACTOR (dBuV/m) HEIGHT (m) (dBuV) (dBuV/m) (Degree) (dB/m) 1 40.30 38.4 QP 40.0 -1.7 1.00 V 181 23.70 14.65 2 88.03 32.3 QP 43.5 -11.2 1.00 V 168 22.66 9.67 3 107.33 32.9 QP 43.5 -10.6 1.00 V 347 21.89 10.99 4 185.13 34.1 QP 43.5 -9.4 1.50 V 360 21.79 12.32 5 197.21 36.0 QP 43.5 -7.5 1.00 V 45 24.58 11.42 6 374.97 34.9 QP 46.0 -11.1 1.50 V 360 17.70 17.18 7 500.02 37.0 QP 46.0 -9.1 1.50 V 110 16.84 20.11 8 624.96 35.5 QP 46.0 -10.5 1.50 V 297 12.73 22.76 REMARKS: 1. Emission level(dBuV/m)=Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value. Report No.: RF991006E02-2 R1 24 Report Format Version 3.0.1 Cancels and replaces the report No.: RF991006E02-2 dated Jan. 18, 2011

4.2.7 TEST RESULTS Above 1GHz WORST-CASE DATA : EUT TEST CONDITION MEASUREMENT DETAIL INPUT POWER 120Vac, 60 Hz FREQUENCY RANGE 1 ~ 25GHz ENVIRONMENTAL 26deg. C, 70%RH DETECTOR Peak (PK) CONDITIONS 1013hPa FUNCTION Average (AV) TESTED BY Rex Huang ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION TABLE CORRECTION LIMIT ANTENNA RAW VALUE NO. FREQ. (MHz) LEVEL MARGIN (dB) ANGLE FACTOR (dBuV/m) HEIGHT (m) (dBuV) (dBuV/m) (Degree) (dB/m) 1 2725.26 41.6 PK 74.0 -32.4 1.05 H 264 9.11 32.49 2 2725.26 6.0 AV 54.0 -48.0 1.05 H 264 -26.49 32.49 3 3633.68 43.7 PK 74.0 -30.3 1.00 H 312 8.85 34.85 4 3633.68 8.1 AV 54.0 -45.9 1.00 H 312 -26.75 34.85 5 4542.10 46.2 PK 74.0 -27.8 1.00 H 354 8.14 38.06 6 4542.10 10.6 AV 54.0 -43.4 1.00 H 354 -27.46 38.06 7 4874.00 46.4 PK 74.0 -27.6 1.34 H 215 7.26 39.14 8 4874.00 34.8 AV 54.0 -19.2 1.34 H 215 -4.34 39.14 9 7311.00 53.3 PK 74.0 -20.7 1.26 H 297 6.67 46.63 10 7311.00 41.2 AV 54.0 -12.8 1.26 H 297 -5.43 46.63 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION TABLE CORRECTION LIMIT ANTENNA RAW VALUE NO. FREQ. (MHz) LEVEL MARGIN (dB) ANGLE FACTOR (dBuV/m) HEIGHT (m) (dBuV) (dBuV/m) (Degree) (dB/m) 1 2725.26 40.9 PK 74.0 -33.1 1.32 V 121 8.41 32.49 2 2725.26 5.3 AV 54.0 -48.7 1.32 V 121 -27.19 32.49 3 3633.68 44.0 PK 74.0 -30.0 1.42 V 81 9.15 34.85 4 3633.68 8.4 AV 54.0 -45.6 1.42 V 81 -26.45 34.85 5 4542.10 46.1 PK 74.0 -27.9 1.22 V 193 8.04 38.06 6 4542.10 10.5 AV 54.0 -43.5 1.22 V 193 -27.56 38.06 7 4874.00 45.7 PK 74.0 -28.3 1.06 V 134 6.56 39.14 8 4874.00 35.0 AV 54.0 -19.0 1.06 V 134 -4.14 39.14 9 7311.00 54.7 PK 74.0 -19.3 1.43 V 194 8.07 46.63 10 7311.00 42.0 AV 54.0 -12.0 1.43 V 194 -4.63 46.63 REMARKS: 1. Emission level(dBuV/m)=Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value. Report No.: RF991006E02-2 R1 25 Report Format Version 3.0.1 Cancels and replaces the report No.: RF991006E02-2 dated Jan. 18, 2011

5 INFORMATION ON THE TESTING LABORATORIES We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited and approved according to ISO/IEC 17025. Copies of accreditation certificates of our laboratories obtained from approval agencies can be downloaded from our web site: www.adt.com.tw/index.5/phtml. If you have any comments, please feel free to contact us at the following: Linko EMC/RF Lab: Hsin Chu EMC/RF Lab: Tel: 886-2-26052180 Tel: 886-3-5935343 Fax: 886-2-26052943 Fax: 886-3-5935342 Hwa Ya EMC/RF/Safety/Telecom Lab: Tel: 886-3-3183232 Fax: 886-3-3185050 Email: service@adt.com.tw Web Site: www.adt.com.tw The address and road map of all our labs can be found in our web site also. Report No.: RF991006E02-2 R1 26 Report Format Version 3.0.1 Cancels and replaces the report No.: RF991006E02-2 dated Jan. 18, 2011

6 APPENDIX A - MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB No any modifications are made to the EUT by the lab during the test. --- END --- Report No.: RF991006E02-2 R1 27 Report Format Version 3.0.1 Cancels and replaces the report No.: RF991006E02-2 dated Jan. 18, 2011


Document Created: 2011-02-09 19:25:28
Document Modified: 2011-02-09 19:25:28
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC