manual

FCC ID: L6G922801

Users Manual

Download: PDF
FCCID_93651

ALLGON SYSTEM AB - Proprietary Technical Specification for PCS Tower Top Power Amplifier [Allgon 9256] Preliminary - Subjected to change without notice Rev.pA0 TOWER TOP POWER AMPLIFIER PCS 1900MHZ / 20W STANDALONE TECHNICAL SPECIFICATION File: 93651 Page 1 (19) 29 Mar 00

ALLGON SYSTEM AB - Proprietary Technical Specification for PCS Tower Top Power Amplifier [Allgon 9256] Preliminary - Subjected to change without notice Rev.pA0 1 INTRODUCTION.......................................................................................................................................... 3 1.1 PURPOSE ............................................................................................................................................... 3 1.2 SCOPE................................................................................................................................................... 3 1.3 REVISION HISTORY.................................................................................................................................... 3 1.4 RELATED DOCUMENTS ............................................................................................................................. 3 1.5 ABBREVIATIONS ....................................................................................................................................... 3 1.6 DEFINITIONS ............................................................................................................................................ 3 2 PRODUCT VARIANT DEFINITION ................................................................................................................ 5 2.1 DEFINITION OF THE AVAILABLE VARIANTS ....................................................................................................... 5 2.2 OPTIONAL FUNCTION SELECTION GUIDE ........................................................................................................ 5 3 SYSTEM OVERVIEW................................................................................................................................... 6 3.1 GENERAL ............................................................................................................................................... 6 3.2 PRINCIPLE OF OPERATION ......................................................................................................................... 7 4 ELECTRICAL SPECIFICATION................................................................................................................... 10 4.1 ABSOLUTE MAXIMUM RATINGS.................................................................................................................. 10 4.2 GENERAL PARAMETERS .......................................................................................................................... 10 4.3 TRANSMIT PATH PARAMETERS.................................................................................................................. 11 4.4 RECEIVE PATH PARAMETERS ................................................................................................................... 13 4.5 FILTER PARAMETERS .............................................................................................................................. 14 4.6 POWER SUPPLY PARAMETERS ................................................................................................................. 14 5 MECHANICAL SPECIFICATION.................................................................................................................. 15 5.1 PHYSICAL PARAMETERS .......................................................................................................................... 15 5.2 INTERFACES ......................................................................................................................................... 15 5.3 MOUNTING ............................................................................................................................................ 16 6 ENVIRONMENTAL SPECIFICATION........................................................................................................... 17 6.1 OPERATING CONDITIONS.......................................................................................................................... 17 6.2 STORAGE AND TRANSPORTATION .............................................................................................................. 17 6.3 ELECTROMAGNETIC COMPATIBILITY (EMC) ................................................................................................. 18 6.4 LIGHTNING PROTECTION........................................................................................................................... 18 7 RELIABILTIY SPECIFICATION ................................................................................................................... 18 7.1 OPERATING LIFE .................................................................................................................................... 18 7.2 THEORETICAL MTBF .............................................................................................................................. 18 7.3 FIELD PROVEN MTBF ............................................................................................................................ 19 8 SAFETY SPECIFICATION .......................................................................................................................... 19 8.1 TOXIC MATERIALS .................................................................................................................................. 19 8.2 SAFETY CLASSIFICATIONS ........................................................................................................................ 19 9 SERVICE AND MAINTENANCE .................................................................................................................. 19 9.1 SERVICE .............................................................................................................................................. 19 9.2 MAINTENANCE ....................................................................................................................................... 19 File: 93651 Page 2 (19) 29 Mar 00

ALLGON SYSTEM AB - Proprietary Technical Specification for PCS Tower Top Power Amplifier [Allgon 9256] Preliminary - Subjected to change without notice Rev.pA0 1 INTRODUCTION 1.1 PURPOSE This document describes the Technical specification for the Allgon Tower Top Power Amplifier for the PCS 1900 cellular band. The product number specified in the header has different variants available. These variants have different bandwidths, gain and options. A definition of the different available variants and a selection guide can be found in chapter 2. 1.2 SCOPE The document details the total Technical performance of the TTPA, with respect to Electrical, Mechanical, Environmental, Safety and Reliability related parameters. Only the mast head mounted unit is described in this document. Other related products, such as APDU and Current Injectors, are described in other documents. 1.3 REVISION HISTORY Rev. pA0 Draft 990518 M.Österberg Rev. Second draft 1.4 RELATED DOCUM ENTS TIA, PS No 3389 Technical Specification for APDU 9209 Technical Specification for CI 9219 1.5 ABBREVIATIONS TTPA Tower Top Power Amplifier PDU Power Distribution Unit APDU Alarm And Power Distribution Unit CI Current Injector PCN Personal Cellular Network AGC Automatic Gain Control ANT Antenna BTS Base Transceiver Station LED Light Emitting Diode MTBF Mean Time Between Failures MTTR Mean Time To Replace PA Power Amplifier 1.6 DEFINITIONS ! Normal operating conditions: The full operating performance specified in this document is guaranteed under conditions stated below: Ambient temperature: Acc. to chapter 7 , after 30 min normal operation. Environment: Acc. to chapter 7 , after 30 min normal operation. DC power supply: Acc. to chapter 4. Return loss: > 18dB on all RF ports. File: 93651 Page 3 (19) 29 Mar 00

ALLGON SYSTEM AB - Proprietary Technical Specification for PCS Tower Top Power Amplifier [Allgon 9256] Preliminary - Subjected to change without notice Rev.pA0 Mounting: Acc. to chapter 5.3 The parameters specified are guaranteed over the warranty time. ! Typical parameters: All typical parameters are considered to be measured at an ambient temperature of 20 °C, and air pressure of 1013 mbar, after 30 min warm up, unless otherwise stated. The TTPA is designed for an operating life exceeding 10 years. File: 93651 Page 4 (19) 29 Mar 00

ALLGON SYSTEM AB - Proprietary Technical Specification for PCS Tower Top Power Amplifier [Allgon 9256] Preliminary - Subjected to change without notice Rev.pA0 2 PRODUCT VARIANT DEFINITION The TTPA are available with different frequency bands, together covering all PCS bands. A number of optional functions (listed in 2.2) are available depending on configuration. The existing, and preferred product configurations, are listen in 2.1. 2.1 DEFINITION OF THE AVAILABLE VARIANTS Variant Band / width RX Freq.band TX Freq.band TX Gain Options 9228.01 A+D / 20 MHz 1850-1870 MHz 1930-1950 MHz 7 dB 1,4,6 9228.02 B+E / 20 MHz 1870-1890 MHz 1950-1970 MHz 7 dB 1,4,6 9228.03* C+F / 20 MHz 1890-1910 MHz 1970-1990 MHz 7 dB 1,4,6 *Future Product 2.2 OPTIONAL FUNCTION SELECTION GUIDE Option See Section Included in variant # 1. Fixed RX Gain 13dB 3.6.2 01,02,03 2. Separate DC connector 4.2.4 3. Separate Alarm connector 4.2.5 01,02,03 4. Redundant DC/DC 3.8.4 5. Antenna supervision 3.4.4 6. RX bypass 3.6.6 7. TX bypass 3.5.11 01,02,03 File: 93651 Page 5 (19) 29 Mar 00

ALLGON SYSTEM AB - Proprietary Technical Specification for PCS Tower Top Power Amplifier [Allgon 9256] Preliminary - Subjected to change without notice Rev.pA0 3 SYSTEM OVERVIEW 3.1 GENERAL The PCS Tower Top Power Amplifier (TTPA) is intended for use at sites where it is necessary to improve the coverage area. The TTPA boosts both the receive-path signal and the transmit power from one TRx in order to preserve site link balance. TX and RX signal paths are separated by means of duplexers. The TX Power Amplifier (PA), as well as the RX Low Noise Amplifier (LNA), utilizes balanced architectures to add redundancy. The TTPA can also be used together with a micro or mini BTS to reach coverage equivalent with a far more expensive Macro BTS installation. The TTPA has a small and lightweight design, which enables it to be mounted in the antenna tower, near the antenna. This means that less costly feeders can be used since the attenuation becomes of less concern when the PA and the LNA is situated near the antenna. DC power to the TTPA is supplied , via the antenna feeder. The TTPA incorporates an advanced self-supervision system that automatically switches the unit into bypass mode in the event of malfunction or power failure. RX/TX RX RX/TX MHB KEY PARAMETERS MHB TX Gain: 7 dB TX Power: +43 dBm (20W) TTA RX Gain: 13dB RX/TX BTS RX RX RX/TX Figure 1. Typical site configuration with Tower Top Amplifiers. File: 93651 Page 6 (19) 29 Mar 00

ALLGON SYSTEM AB - Proprietary Technical Specification for PCS Tower Top Power Amplifier [Allgon 9256] Preliminary - Subjected to change without notice Rev.pA0 3.2 PRINCIPLE OF OPERATION 3.2.1 General The TTPA has the RX and the TX signal paths separated by means of duplex filter or isolators. All circuitry for power supply and supervision are included inside the unit. The TTPA has two ports designated BTS and ANT. The BTS port carries the signals to/from the BTS rack (e.g. TX-in, RX-out, DC-power). The ANT port will be connected to the antenna. See figure 2 Basic TTPA Block Diagram. RX byp ass ANT port BTS port CI & LP dB dB dB In pu t Pow er Forwa rd Re ve rse Pow er Pow er EXT.D C op ti on TX byp ass SYSTEM CONTROLLE EXT:AL ARM op ti on 26 V dB DC /D C 26V Figure 2. Block diagram of the Tower Top Power Amplifier. 3.2.2 Transmit Path The Transmit path incorporates a balanced power amplifier with high linearity. An Automatic Gain Control circuit (AGC) keeps the gain at a constant level from input to ANT output. TX-path Bypass is optional. 3.2.3 Receive Path The Receive path consists of a balanced LNA with very low noise factor. The LNA has a gain change capability in order to compensate for different feeder losses and optimize the link budget on each site. RX bypass, which will cut in at power failure or LNA failure, is an optional function. 3.2.4 Power Supply The Power Supply filters and regulates the input DC power to suit the amplifiers. DC power fed into the unit on the BTS input connector through the feeder is standard. Separate DC connector and redundant DC/DC is optional. File: 93651 Page 7 (19) 29 Mar 00

ALLGON SYSTEM AB - Proprietary Technical Specification for PCS Tower Top Power Amplifier [Allgon 9256] Preliminary - Subjected to change without notice Rev.pA0 3.2.5 Supervision A number of parameters are constantly supervised. TX Power Amplifier: Output power, VSWR (when input power within specified limits), transistor currents, voltages, temperature and power supply. VSWR supervision optional. RX LNA: Transistor currents and power supply. Control unit: The system controller at startup and at certain intervals makes a system self-test. 3.2.6 Alarming The TTPA has an alarm connector with two independent relay contacts and an auxillary input. The Relays are assigned to different alarms depending on whether it is a Major or Minor alarm (Relay 1=Major, Relay 2=Minor). This facilitates differentiation of minor alarms (not interrupting transmission) from major alarms that indicates loss of transmission. All alarms can be gated to one by simply connecting the contacts in parallel. ALARM Cause Action in TTPA Relay # Overtemp Cooling flange above 80°C** RX_bypass****/TX Bypass**** 1 DC-Minor One DC/DC-converter failed none 2 DC-Major**** No DC power to TTPA * TX Bypass 1 TX-Minor One PA Transistor failed None 2 TX-Major PA Failure, No Gain PA shutdown & TX Bypass 1 RX-Minor One LNA Transistor failed None 2 RX-Major LNA Failure none 1 VSWR Alarm**** VSWR > 2.5:1*** none 2 OP-Alarm Output Power over Limit none 2 IP-Alarm Input Power over Limit none 2 RP-Alarm**** Reflected Power over Limit none 2 AGC-Alarm Gain control failed Gain accuracy reduced 2 AUX-Alarm**** Auxillary input shorted none1 2 TTA_Minor**** Diversity TTA minor failure none 2 TTA_Major**** Diversity TTA major failure none 2 SYS_Minor CPU System test failed none 2 SYS_Major CPU System test failed TX Bypass**** 1 * Either due to failure of both DC/DC converters, or no DC power applied to the unit. ** restart at +60°C *** Default value. Software changeable level 2:1 to 5:1 is optional File: 93651 Page 8 (19) 29 Mar 00

ALLGON SYSTEM AB - Proprietary Technical Specification for PCS Tower Top Power Amplifier [Allgon 9256] Preliminary - Subjected to change without notice Rev.pA0 **** Optional function, not supported in all variant. File: 93651 Page 9 (19) 29 Mar 00

ALLGON SYSTEM AB - Proprietary Technical Specification for PCS Tower Top Power Amplifier [Allgon 9256] Preliminary - Subjected to change without notice Rev.pA0 ELECTRICAL SPECIFICATION 3.3 ABSOLUTE MAXIM UM RATINGS The Absolute Maximum Rating is defined as the value of applied signal/power etc. that is guaranteed not to damage the unit permanently. This applies over the full operating temperature range of the unit. Parameter MAX MIN Unit 3.1.1 Input DC Voltage (low imp. Source) - -70 V 3.1.2 Reverse Input DC Voltage 75 - V 3.1.3 Input Power on BTS port (TX-band) 40 - dBm 3.1.4 Input Power on ANT port (TX-band) 43 - dBm 3.1.5 Input Power on BTS port (RX-band) 20 - dBm 3.1.6 Input Power on ANT port (RX-band) 20 - dBm 3.1.7 Input Power on ANT port (other bands) 43 - dBm 3.1.8 Input Power on BTS port (other bands) 40 - dBm 3.4 GENERAL PARAM ETERS 3.4.1 Nominal Impedance Nominal impedance of all ports: 50Ω 3.4.2 Return Loss Measured over the tuned Rx and Tx band. Normal operation: Bypass: BTS port: > 18 dB BTS port > 12 dB ANT port: > 18 dB Ant port: > 12 dB 3.4.3 Power Consumption Max: 130W (2.5A @48V) Primary Fuse: 4 A Slow 3.4.4 Antenna Supervision (VSWR) (option 5) This optionally feature monitors the Forward and Reflected power at the ANT port. If calculated VSWR exceeds the VSWR LIMIT, a VSWR-alarm is issued. The VSWR value below is the default value and is optionally software changeable from 2:1 to 5:1. VSWR Return Loss VSWR LIMIT: 2.5:1 ~7.4 dB The VSWR-alarm is active down to an average output signal power > 20 dBm. 3.4.5 Reflected Output Power Supervision If the reflected power from the antenna exceeds +38 dBm, the reflected power supervision function will decrease the TX gain in order to limit the reflected power to a level less than +38dBm. An RP_Alarm alarm will be issued in this condition . File: 93651 Page 10 (19) 29 Mar 00

ALLGON SYSTEM AB - Proprietary Technical Specification for PCS Tower Top Power Amplifier [Allgon 9256] Preliminary - Subjected to change without notice Rev.pA0 3.4.6 Total Feeder DC Resistance and Maximum Feeder Length Maximum length: 250 m (833 ft) Maximum feeder DC resistance: 2Ω Measured between the inner and outer connector with the other feeder end short circuited. **Note: Only valid when using feeder cable for DC-feed. 3.4.7 Intermodulation Distorsion The measurements are made on both ports with the TTPA operating at its nominal rated output power and with: Two interfering signals in the PCS-RX band at a power level of -40 dBm at ANT port. One interfering signals in the PCS-TX band at a power level of +13 dBm at ANT port. Maximum IMD level: Band ANT port BTS port Meas BW RX -128 dBm -114 dBm 100 kHz TX -70 dBc -70 dBc 100 kHz 3.5 TRANSM IT PATH PARAM ETERS 3.5.1 TX Operating Frequency -See section 2.1 3.5.2 TX Nominal Output Power Measured at the ANT port, within the tuned TX band. Min: +43 dBm (20W) 3.5.3 TX Overload Supervision When the average Output Power exceeds 43 dBm with: > 1.0 dB an TX-OP Minor Alarm (TX Over Power) alarm is issued > 2.0 dB the TX power is soft limited by the AGC circuitry not to exceed this value. and a TX-OP Major Alarm is issued. 3.5.4 TX Two Tone Linearity Measured with two CW signals of 37dBm each (43dBm Peak Power) out from the unit in TX band, giving 40dBm total average output power. Max 1MHz spacing between tones. Level of IM-tones Max: -30dBc 3.5.5 TX Nominal Gain Nominal Gain is defined as [MaxGain(inband) + MinGain(inband)] / 2 7dB File: 93651 Page 11 (19) 29 Mar 00

ALLGON SYSTEM AB - Proprietary Technical Specification for PCS Tower Top Power Amplifier [Allgon 9256] Preliminary - Subjected to change without notice Rev.pA0 3.5.6 TX Gain Tolerance Measured with AGC in operation. Nominal gain ± 0.5 dB 3.5.7 TX Gain Ripple Ripple is defined as [MaxGain(inband) - MinGain(inband)] Max: 1 dB 3.5.8 TX AGC Operation The AGC system continuously holds the TX-gain at nominal value. If the system fails to regulate the power a PA-fail alarm is generated. The AGC time constant is chosen to compensate for thermal and other long term drift. Minimum average input power level for AGC operation: +20 dBm. TX gain tolerance with AGC not operating: ±1.5dB. 3.5.9 TX Stability The TX-amplifier is unconditionally stable for all passive loads at input and output. 3.5.10 TX Spurious Emissions and Broadband Noise Measured at ANT port, with the TTPA operating at nominal output power. Peak power and measurement bandwidth as listed in table. Outside TX band: Frequency band Max peak power / Bandwidth RX band - 128 dBm / 100 kHz 1850-1910 MHz - 98 dBm / 100 kHz 824 - 849 MHz - 98 dBm / 100 kHz 100 kHz - 50 MHz - 36 dBm / 10 kHz 50-1000 MHz - 36 dBm / 100 kHz 1 – 12.75 GHz, outside TX band >+ 2 MHz - 30 dBm / 30 kHz “ >+ 5 - 30 dBm / 100 kHz MHz “ >+ 10 - 30 dBm / 300 kHz MHz “ >+ 20 - 30 dBm / 1 MHz MHz “ >+ 30 - 30 dBm / 3 MHz MHz Inside TX band: Frequency band Max peak power / Bandwidth Carrier offset > + 1.8 MHz - 36 dBm / 30 kHz Carrier offset > + 6 MHz - 36 dBm / 100 kHz File: 93651 Page 12 (19) 29 Mar 00

ALLGON SYSTEM AB - Proprietary Technical Specification for PCS Tower Top Power Amplifier [Allgon 9256] Preliminary - Subjected to change without notice Rev.pA0 3.5.11 TX Bypass Loss (option 7) TX bypass function is optional. Measured from ANT to BTS port Typ. 2.0 dB Max: 2.6 dB 3.5.12 TX Redundancy & Bypass Operation In the event of failure of one of the transistors in the power amplifier the gain will drop by approx. 6dB. In this condition a TX-minor alarm will be generated. If both transistors fail and the TX Bypass option is installed, the TX-path will be switched to bypass mode and a TX-major alarm will be issued. Bypass mode will automatically be initiated if DC power to the PA fails. 3.6 RECEIVE PATH PARAM ETERS 3.6.1 RX Operating Frequency -See section 2.1 3.6.2 RX Gain Nominal Gain is defined as [MaxGain(inband) + MinGain(inband)] / 2 13 dB Optionally reduced in 1 dB steps from 13 to 7 dB. 3.6.3 RX Gain Tolerance ±0.6 dB 3.6.4 RX Gain Ripple Ripple is defined as [MaxGain(inband) - MinGain(inband)] ±0.5 dB 3.6.5 RX Noise Figure Measured at Nominal RX gain. Typ: 1.9 dB Max: 2.9 dB 3.6.6 RX Bypass Loss ( option 6 ) RX bypass function is optional. Measured from ANT to BTS port Typ. 2.2 dB Max 2.9 dB 3.6.7 RX Input Intercept Point IIP3 Min: +6dBm File: 93651 Page 13 (19) 29 Mar 00

ALLGON SYSTEM AB - Proprietary Technical Specification for PCS Tower Top Power Amplifier [Allgon 9256] Preliminary - Subjected to change without notice Rev.pA0 3.6.8 RX Stability The RX-amplifier is unconditionally stable for all loads at input and output of the TTPA. 3.6.9 RX Redundancy In the event of failure of one of the transistors in the balanced LNA the gain will drop by approx. 6dB. An RX-minor alarm will be generated. If both transistors fail, an RX-major alarm will be generated. 3.7 FILTER PARAM ETERS Rx and Tx bands according to paragraph 2.1 Isolation ANT to LNA input DC – 1000 90 dB 1000 – {35 MHz below Rx Band} 30 dB 1910 – 1990 50 dB Tx Band (20 MHz wide) 85 dB 1990 – 5970 40 dB 5970 – 12750 20 dB 3.8 POWER SUPPLY PARAM ETERS 3.8.1 Supply Voltage - 48 Volts DC 3.8.2 Supply Voltage Tolerance Measured at BTS port. Max: -60V Min: -40 V 3.8.3 Supply Voltage Noise Tolerance ! Ripple and noise 10Hz to 100 MHz: 100 mV p-p ! Wideband noise 4kHz to 20 MHz, any 3kHz band: 1V p-p 3.8.4 DC/DC Redundancy (option 4) The power supply consists of two DC/DC converters in parallel, sharing the current. In the case off one converter failing, the remaining converter will power the unit to full operation. An alarm (DC-minor) will be signaled to the PDU. If both DC/DC converters fails, or no power is applied to the unit, the APDU detects this automatically and raises an alarm. 3.8.5 DC Input Protection ! Reverse Voltage Protection ! Over voltage Protection ( see lightning spec.) ! Over current protection File: 93651 Page 14 (19) 29 Mar 00

ALLGON SYSTEM AB - Proprietary Technical Specification for PCS Tower Top Power Amplifier [Allgon 9256] Preliminary - Subjected to change without notice Rev.pA0 3.8.6 Inrush Current Measured at power on with nominal supply voltage. Max peak: 15A Max after 10ms: 3A 4 MECHANICAL SPECIFICATION 4.1 PHYSICAL PARAM ETERS 4.1.1 Height 350 mm (±20mm) 4.1.2 Width 220 mm (±20mm) 4.1.3 Depth 230 mm (±20mm) 4.1.4 Volume 3 17 dm 4.1.5 Weight - Clamping Unit 3 kg 4.1.6 Weight - Amplifier Unit 12 kg (26.5 lb) 4.1.7 Color RAL 7035 and Nature Anodized Aluminum, non reflective. 4.1.8 Wind Load ~155 N @ 150 km/h (41.67 m/s) 4.1.9 Materials All plastic materials are characterized according to ISO 1043. 4.1.10 Weatherproofing UL50/IP 65 4.2 INTERFACES The TTPA has total of two (2) ports designated BTS and ANT. The BTS Connector carries the signals to/from the BTS rack (e.g. TX-in, RX-out, DC-power and Alarm signaling). The ANT connector should be connected to the antenna. File: 93651 Page 15 (19) 29 Mar 00

ALLGON SYSTEM AB - Proprietary Technical Specification for PCS Tower Top Power Amplifier [Allgon 9256] Preliminary - Subjected to change without notice Rev.pA0 4.2.1 BTS Connector 7/16 Female 4.2.2 ANT Connector 7/16 Female 4.2.3 Earthing Earthing stud: M8 x 15mm 4.2.4 DC Connector (option 2) Optional DC connector for separate DC, see 2.2 Type: Binder series 623 , 6 poles, male 4.2.5 Alarm Connector (option 3) Optional alarm connector, see 2.2 Type: Binder series 623 , 12 poles, male 4.2.6 Power ON LED Optional LED, indicating POWER ON Color: Green 4.3 MOUNTING NOTE: DC power must be connected to the TTPA within one day after mounting to prevent damage due to moisture. 4.3.1 Mounting method The TTPA is equipped with a pole clamping unit. This enables the installation personnel to first install the relatively light mast clamp, and then easily hook on the actual amplifier. This feature reduces the risk of accidents during installation. ! Pole mounting with clamps. Pole diameter: 50 - 120 mm ! Wall mounting by means of mounting plate. 4.3.2 Mounting Time The unit is designed to be easily mounted by normally skilled installation personnel in less than 20 minutes. (Not including commissioning ) 4.3.3 Mounting Requirements ! The unit must have non obstructed free air to a distance of 0.5m from TOP and BOTTOM sides, and 0.2 m from all other sides, except BACK side. ! Mounting angle: Vertically ±10° (Applies to completed mounting, TTPA in operation) 4.3.4 MTTR Less than 15 min (excluding commissioning ) File: 93651 Page 16 (19) 29 Mar 00

ALLGON SYSTEM AB - Proprietary Technical Specification for PCS Tower Top Power Amplifier [Allgon 9256] Preliminary - Subjected to change without notice Rev.pA0 5 ENVIRONMENTAL SPECIFICATION 5.1 OPERATING CONDITIONS ( Conditions: The unit mounted in free air, DC power applied at all times.) 5.1.1 Ambient Air Temperature Full Performance Max: + 50 °C Min: - 35 °C 5.1.2 Survival Operational Temperature Max: + 80 °C Min: - 40 °C When the internal temperature exceeds +80°C the power is reduced and the transmission path goes into bypass mode. Resets automatically when the temperature decreases. 5.1.3 Relative Humidity Max: 100 % Min: 8% 5.1.4 Absolute Humidity 3 Max: 30 g/m 3 Min: 0.26 g/m 5.1.5 Rate of Temperature Change Max: 1°C/min (ambient) 5.1.6 Air Pressure Max: 106 kPa Min: 70 kPa 5.1.7 Solar Radiation 2 Max: 1125 W/m (with solar cover) 5.1.8 Vibration According to: ETS 300 019-2-4 5.1.9 Applicable Test Standards ETS 300 019-2-4 class T4.1 80 / 85 environmental test 5.2 STORAGE AND TRANSPORTATION ( Conditions: 6 months storage of unit in original shipping container with intact sealing ) 5.2.1 Ambient Air Temperature Max: + 85 °C Min: - 45 °C File: 93651 Page 17 (19) 29 Mar 00

ALLGON SYSTEM AB - Proprietary Technical Specification for PCS Tower Top Power Amplifier [Allgon 9256] Preliminary - Subjected to change without notice Rev.pA0 5.2.2 Relative Humidity Max: 100 % Min: 8% 5.2.3 Absolute Humidity 3 Max: 30 g/m 3 Min: 0.26 g/m 5.2.4 Rate of Temperature Change Max: 2°C/min (ambient) 5.2.5 Air Pressure Max: 106 kPa Min: 50 kPa 5.2.6 Vibration According to: ETS 300 019-2-1 ETS 300 019-2-2 IEC 68-2-6 IEC 68-2-36 IEC 68-2-29 IEC 68-2-32 5.2.7 Applicable Test Standards Transport: ETS 300 019-2-2 class T2.3 Storage: ETS 300 019-2-1 class T1.2 5.3 ELECTROM AGNETIC COM PATIBILITY (EMC) Complies to: ETS 3000 342-2 IEC 1000-4-5 FCC Part 24 FCC Part 15 5.4 LIGHTNING PROTECTION According to IEC 1000-4-5 extended to 10 kA short circuit current. ANT port DC grounded 6 RELIABILTIY SPECIFICATION 6.1 OPERATING LIFE The TTPA is designed for an operating life exceeding 10 years. 6.2 THEORETICAL MTBF Theoretical MTBF is calculated according to MIL-HDBK-217F, part stress method, ground fixed, uncontrolled environment, 40°C ambient temperature. If available, practically derived reliability data is used in place of statistical in the calculation. This calculation yields an MTBF of > 25000 hours. File: 93651 Page 18 (19) 29 Mar 00

ALLGON SYSTEM AB - Proprietary Technical Specification for PCS Tower Top Power Amplifier [Allgon 9256] Preliminary - Subjected to change without notice Rev.pA0 Note: the calculated MTBF gives a very conservative value. Especially when the components MTBF is based on the default data specified in MIL-HDBK-217F and not from an accelerated life time test. If such data was available on every component then a result close to the field proven MTBF could be calculated. 6.3 FIELD PROVEN MTBF The TTPA is designed to demonstrate a field proven MTBF of over 200000 hours, calculated over a period exceeding one (1) year. 7 SAFETY SPECIFICATION 7.1 TOXIC MATERIALS No toxic materials is used within the unit. 7.2 SAFETY CLASSIFICATIONS CE-Recognition: EN 60950 UL-Classification: UL 1950 8 SERVICE AND MAINTENANCE 8.1 SERVICE No field serviceable parts inside. Failed unit must be returned to Allgon. Service only by qualified personnel authorized by Allgon. 8.2 MAINTENANCE No periodic maintenance necessary. File: 93651 Page 19 (19) 29 Mar 00


Document Created: 2000-03-29 12:12:18
Document Modified: 2000-03-29 12:12:18
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC