User Manual

FCC ID: KUTSW100R

Users Manual

Download: PDF
FCCID_680572

Skylink Wireless Switch Receiver Model SW—100R 1. INTRODUCTION 5. OPERATION (CONT) To work with AM—001: In this package, you will find a wireless switch receiver. SW100R can communicate with AM—001 control panel by sending confirma— tion signal to AM—001 telling it whether the control of the appliances con— nected to SW100R by AM—001 is success or fail. Step 1: in the AM—001 contral panel, press the program button+ password+ Key 4 +1—5(any key). Step 2: Press the side button in the SW100R once, a signal will be transmitted to AM—001. The voice "device 1—5 (depend on which key is pressed in step1) is 2. INSTALLATION accepted" will be heard indicating successful learning. € Piug the receiver into a powered, Step 3: Press and hold the SW100R side button. The LED will flash. 120VAG electrical outlet inside your house. (Note: This receiver is designed Step 4: Press Key 6—0(depend on which key is pressed in step1, if key 1 is to be used indoor only. Do not use this pressed, then key 6 should be pressed, if key 2 is pressed, then key 7 should be receiver in an outdoor environment.) pressed. etc) on the AM—001. Signal will be transmitted to SWA100R and the LED on the SW100R will be off. € Once the receiver is plugged into an electrical outlet, the red LED on the front Step :AM—001 can now control the appliances connected to SW100R, Press of the unit will be "an" indicating the unit 6—0(depends on the key learnt in step4), the appliances will be on, and a is in standby mode. confirmation signal" device on accepted" will be heard from AM—001.Press the corresponding key(1—5), the appliances will be off and a confirmation signal" 9 Plug in the light fixture or small appliance device off accepted" will be heard from AM—001 that you would like to control into the receiver, as shown. Cebenoulell RISK OF ELECTRICAL SHOCK. FOR INDOOR USE ONLY. €) if there is a power switch on the plugged CAUTION : NOT FOR USE WITH DIMMER. DISCONNECT POWER BEFORE in light fixture or small appliance, please SERVICING. turn it on. The receiver is ready to be Maximum Rating : activated. Input : 120VAC 60Hz Resistive : 8A (G8OW Incandescent : 300 watts Motor Load : 1/3 HP 3. PROGRANM A TRANSMITTER HE RECEIVER This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This deviee may not cause harmful You need to do the programming in order to add a transmitter to the interference, and (2) This device must accept any interference received, receiver. including interference that may cause undesired operation. WARNING: o Plug the receiver into an electrical socket. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user‘s authority to operate the Press and hold the learn button on the left hand side of the receiver. equipment. The red LED on the receiver will flash, NOTE: This equipment has been tested and found to comply with the limits for a 9 Simultaneously, press your assigned button of transmitter 4B—101 Class B digital device, pursuant to Part 15 of the FCC Rules. These limits {either button A, B, C or D) you want to program to the receiver. are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses The receiver red LED will go off indicates the programming is and can radiate radio frequency energy and, if not installed and used in completed. accordance with the instructions, may cause harmful interference to radio communications. To program the transmitter to control anather receiver, repeat However, there is no guarantee that interference will not occur in a particular process (1) to (4) but pressing another button. installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ~ Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. ~— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Madel 48101 — Consult the dealer or an experienced radio/TV technician for help. 8, WARRANTY Pss NSMITTER FROM THERECE If, within one year from date of purchase, this product should become defective {except battery), due to faulty workmanship or materials, it will be repaired or You can delete the transmitter from a receiver. replaced, without charge. Proof of purchase and a Return Authorization are required. if you would like to order Skylink‘s products or have difficulty getting them to work, 0 Unplug the receiver from the electrical socket. please: @ Press and hold the learn button on the left hand side of the receiver 1. visit our FAQ section at wwwsivinkhome.cam, or when plugging the receiver into an electrical socket, the red LED on the 2. email us at support@skylinkhome.com, or 3. call ourtall free at 1—800—304—1187 from Monday to Friday, 9 am to 5 pm receiver will flash rapidly. All the transmitters are deleted. EST. Fax (800) 286—1320 5. OPERATION CUSTOMER SERVICE 17 Sheard Avenue, Brampton, Ontario, Canada LGY 1J3 To activate the receiver, simply press the appropriate button on the 1180—D East Francis Street, Ontario, CA. 91761 U.SA. transmitter, it will activate the plugged in device. Pressing it again will turn Email:support@skylinkhome.com off the plugged in device. hittp:/fmwwskylinknome.com PN.101AGORevt ©2005 SKYLiNKGROUP


Document Created: 2005-07-12 12:32:30
Document Modified: 2005-07-12 12:32:30
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC