User manual

FCC ID: KUTMK318

Users Manual

Download: PDF
FCCID_1500526

3-Button Garage Door Remote Control Model MK-318 1. INTRODUCTION 2c. PROGRAM A TRANSMITTER TO RECEIVER GB-318-3 ® In this package, you will find a Skylink garage door transmitter with 3V To program the transmitter to a Skylink Garage Door lithium battery. Receiver Smart ButtonTM GB-318-3 (3 doors) , please follow the user’s instruction for the model GB-318-3. Garage Door Transmitter (Battery inside) 2d. PROGRAM A TRANSMITTER TO THE SKYLINK® GARAGE DOOR OPENER - IQ SERIES There are three buttons on transmitter MK-318, each button can be To program the transmitter to the Skylink® IQ series Garage Door Opener, programed to control Skylink garage door receiver Smart ButtonTM GB-318 please follow the user’s instruction from the Garage Door Opener. or GB-318-3 or Skylink garage door opener directly. Follow one or more instructions below in Section 2 to program transmitter 3. TROUBLE SHOOTING MK-318 to the receiver or receivers you want to control. Q: What can I do if the door opener does not react after I press the button on the transmitter ? 2a. PROGRAM TRANSMITTER TO RECEIVER GB-318 A: - Ensure when the button on the transmitter is pressed, the red light on the You need to do the programming in order to add the transmitter - remote transmitter comes on. Otherwise, check if the battery is inserted properly. control to a receiver. - Make sure the correct button on the transmitter is pressed. - Ensure the wires that were previously connected to the wall mounted Refer to the receiver Smart ButtonTM GB-318 user’s instruction to set up the unit. door control are not loose. Smart ButtonTM GB-318 can learn up to 10 remote controls. - Ensure the transmitter has been programmed to the receiver. Refer To program the transmitter to the receiver, follow the instructions below: to section 2 for how to program a transmitter to the receiver. 1. Press the learn button on the side of the Smart ButtonTM GB-318. 2. Once the learn button is pressed, the LED will 4. BATTERY flash quickly. Release the learn button. 3. Within 30 seconds, press any one of the 3 buttons Antenna 3 Volt lithium battery (CR 2032) (included). It is time to change the battery when the red LED on the transmitter does on the transmitter that you want to program to the not turn on when either button is pressed. receiver. 4. Once the remote control is programmed, the LED LED will flash slowly, in the same way as it flashes 5. FCC in standby mode. 5. You may now operate the garage door opener Learn This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: Button (1) This device may not cause harmful interference, and (2) This device must accept any interference with this new remote control. received, including interference that may cause undesired operation. 6. To program this transmitter to control another Smart ButtonTM WARNING: receiver, repeat process (1) to (4) to program GB-318 Changes or modifications to this unit not expressly approved by the party responsible for compliance could another button on the remote control. void the user’s authority to operate the equipment. 6. IC 2b. PROGRAM A TRANSMITTER TO THE SKYLINK® GARAGE DOOR OPENER - EQ SERIES Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) L’appareil ne doit pas produire de You need to do the programming in order to add the transmitter to a brouillage, et (2) L’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le Skylink® Garage Door Opener. brouillage est susceptible d’en compromettre le fonctionmement. Skylink® Garage Door Opener can learn up to 16 remote controls. 7. WARRANTY If, within one year from date of purchase, this product should become defective To program the transmitter to the Garage Door Receiver, follow the (except battery), due to faulty workmanship or materials, it will be repaired or instructions below: replaced, without charge. Proof of purchase and a Return Authorization are required. 1. Press the LEARN/SET button once on the garage door opener. 2. Once the LEARN/SET buttton is pressed, the LEARN LED will flash. You may release the LEARN/SET button. 8. CUSTOMER SERVICE 3. Within 30 seconds, press any one of the 3 buttons on the transmitter that you want to program to the receiver. If you would like to 4. Once the transmitter is programmed, the LEARN LED will turn off. - find out the up-to-date specifications 5. You may now operate the garage door opener with this new transmitter. - know more about features and applications - download documents, i.e. user’s instructions 6. To program a transmitter to control another garage door opener, - order Skylink products repeat process (1) to (4) to program another button on the transmitter. or if you have difficulty getting products to work, please: Learn Button 1. visit our FAQ section at www.skylinkhome.com, or 2. email us at support@skylinkhome.com, or 3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST. Fax (800) 286-1320 CUSTOMER SERVICE 17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3 Email:support@skylinkhome.com http://www.skylinkhome.com P/N : 101Z993 Patent Pending ©2010 SKYLINK GROUP


Document Created: 2011-07-12 13:12:01
Document Modified: 2011-07-12 13:12:01
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC