Users Manual

FCC ID: KFR-ZT1101US-5

Users Manual

Download: PDF
FCCID_2877175

Federal Communications Commission Statement This equipment has been followed to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interferene by one of the following measures: Reorient or relocate the receiving antenna, Increase the separation between the equipment and receiver, Connect the equipment into and outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undersired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. Limited Warranty Installation & Operation Manual Vision Guarantees that every keyfob is free from physical defects in material and workmanship under normal use for one year from the date of purchase. If the product proves defective during this one-year warranty period, Vision will replace it free of charge. Vision does not issue any refunds. This warranty is extended to the original end user purchase only and is not transferable. This warranty does not apply to : (1) damage to ZT1101IN-5 units caused by accident, dropping or abuse in handling, or any negligent use; (2) units ZT1101MY-5 which have been subject to unauthorized repair, taken apart, or otherwise modified; (3) units not used in accordance with instruction; (4) damages exceeding the cost of the ZT1101EU-5 product; (5) transit damage, initial installation costs, removal cost, or reinstallation cost. For information on addional devices, plesae visit us at www.visionsecurity.com.tw ZT1101RU-5 ZT1101US-5 ZT1101IL-5 ZT1101HK-5 ZT1101KR-5 ZT1101BR-5 ZT1101JP-5 Z-Wave Keyfob Keyfob (w/o AES version) ZT1101-5 V1 1040703 6B1Z-11001 ‫ي‬

Introduction ‫ و‬enabled device Thanks for choosing the Keyfob of the home security device. This keyfob is a Z-Wave™ Installation/Operation (interoperable, two-way RF mesh networking technology) and is fully compatible with any Z-Wave™ enabled network. Every main powered Z-Wave enabled device acts as a signal repeater and multiple Notice: If you are installing the entire Z-Wave™ system for the first time, please refer to devices result in more possible transmission routes which helps eliminate “RF dead-spots” the installation guide of Z-Wave™ Interface Controller before installing keyfob. Z-Wave™ enabled devices displaying the Z-Wave™ logo can also be used with it regardless of the 1. There's a DIP switch at the bottom of keyfob. Different positions manufacturer, and ours can also be used in other manufacturer’s Z-Wave™ enabled networks. This corresponds to different functionalities that described in the following device could help you control the Z-WAVE devices you learned in the gateway or directly in this keyfob sections (need association). It is rechargeable portable controller. Product Description and Specification 2. Setup Z-Wave Network: Specification: Package Content: A) To “Include” into (adding into) or “Exclude” from (removing from) an existing Protocol: Z-Wave™ (ZM5101N) 1pc Keyfob network: Put the Z-Wave™ Gateway or Controller into learn mode to add or remove Frequency Range: 1pc Installation & Operation manual the keyfob into/from your controller. To get in to “inclusion” or “exclusion” mode, the 865.22MHz (ZT1101IN-5) 1pc Micro USB/USB cable distance between sensor and controller is suggested to be within one meter. (See 868.10MHz (ZT1101MY-5) 868.42MHz (ZT1101EU-5) 3.Control Mode: 1)Learn Mode & 4.Setup Mode: 5)Learn Mode via NWI) 869.00MHz (ZT1101RU-5) 908.42MHz (ZT1101US-5) B) Association Set From Gateway/Primary Controller: 916.00MHz (ZT1101IL-5) * Keyfob supports 5 groups; group 1 (Lifeline) – “Central Scene”, group 2~5 (Scene 919.80MHz (ZT1101HK-5) 920~923MHz (ZT1101KR-5) Activation). 921.42MHz (ZT1101BR-5) * Primary Controller or Gateway could association nodes to all its groups 1~5. 922~926MHz (ZT1101JP-5) Operating Range: Up to 100 feet line of sight C) Keyfob can form its own network. In this case it's role is primary controller and Operating Temp.: -15°C~ 60°C (5°F ~140°F) 4 Battery: Lithium-Ion Rechargeable Battery (220mAh) capable of include/exclude other devices or controllers into its own network. It can also Z-Wave Supported Command Classes: organize its Scene Activation Groups 2~5.(See 4.Setup Mode). It can also hand over COMMAND_CLASS_ASSOCIATION_GRP_INFO its primary role to other controllers in network by Controller Shift (See 4.Setup Mode). COMMAND_CLASS_ ASSOCIATION_V2 COMMAND_CLASS_ BATTERY D) When Keyfob's role is secondary controller, it can become primary controller by COMMAND_CLASS_CENTRAL_SCENE COMMAND_CLASS_DEVICE_RESET_LOCALLY entering learn mode while Primary Controller uses its controller shift function.(please COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2 refer to its manual for detail). COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2 COMMAND_CLASS_POWER_LEVEL 3. Control Mode (DIP SWITCH TO RIGHT): COMMAND_CLASS_VERSION_V2 COMMAND_CLASS_WAKE_UP_V2 1) Learn Mode: COMMAND_CLASS_ ZWAVEPLUS_INFO_V2 * Keyfob should not include any node * Press button 1 and 4 together till the red LED flashes to * Keyfob will return to sleep after 5 seconds if no inclusion nor exclusion. 2) Wake Up Notification Press button 2 and 3 together until green LED flashes. Keyfob will first send NIF (without entering learn mode) and then send Wakeup Notification 5 seconds later. 3) Wake Up Interval Use Wakeup Interval Set command to set wakeup time to send “Wake Up Notification” to assigned node. User could change the auto wake up from 4 minutes to 1 week. The minimal increment interval is 4 minutes. * Default Value: 6 hours 4) Battery Capacity Detection: * Send “Battery Get” command, and then wake up device as described in 2) above, to have the battery capacity back in %. * It will detect the battery capacity automatically every 2 hours. * Low Battery Auto Report to Group 1 (Lifeline) Nodes. * Full Capacity: 0x64 / Low Battery Warning: 0xFF ‫و‬ ‫ﻮ‬

5) Switch All ON/OFF: * Press button 1 and 4 together until green LED flashes * Open All: Press button 1 and 2 together until the green LED flash once and the * Keyfob will go back to sleep if no node info received within 10 seconds. keyfob will send “SWITCH_ALL_ON” command * Close All: Press button 3 and 4 together until the red LED flash once and the keyfob will send “SWITCH_ALL_OFF” command 2) Exclude other devices from Keyfob's network: * Keyfob must be the primary controller * Press button 2 and 3 together until red LED flashes. 6) Mode Switch: * Keyfob will go back to sleep if no node info received within 10 seconds. * Press button 2 and 4 together until green LED flashes to switch to “Central Scene Mode”. * Press button 1 and 3 together until red LED flashes to switch to “Scene 3) Controller Shift: Activation Mode”. * Keyfob must be the primary controller. * Press button 1 and 3 together until green LED flash, then red LED flash. 7) Central Scene Mode(Group 1): * Put another controller which you want it to become primary into learning mode. * Short press (each button, press time <1 second): - The green LED will flash once and send “Central Scene Notification” 4) Disassociation/Association for Scene Activation Groups (2~5): command (Key Attribute 0x00) to all Group 1 (Lifeline) Nodes. * Press button 2 and 4 together until green LED flashes * Long press (each button, press time >2 seconds): * Release both button and the red LED will flashes twice; choose which button - The red LED will keep flashing while long pressing the button and send group to associate and held corresponding button. “Central Scene Notification” command (Key Attribute 0x02) every 150ms to * Let the device which going to be associated sending NIF. Group 1 Nodes. * Green LED will start flashes if association is successful. Now you can release * Release the button (After long press): the button. -The orange LED will flash while release the button and send “Central Scene * If the device has already been associated to that button already, this operation Notification” command (Key Attribute 0x01) to the pairing group. will disassociate it from that button and instead Red LED flashes. * Keyfob will be back to sleep if no any button is helded within 4 seconds. * Corresponding Scene Number and Group: Button 1 Button 2 Button 3 Button 4 5) Learn Mode via NWI: Scene number 1 Scene number 2 Scene number 3 Scene number 4 * Keyfob should not include any node * Press button 3 and 4 together till the red LED flashes to enter learn mode, and it will broadcast NWI NIF. 8) Scene Activation Mode: * Keyfob will return to sleep after 5 seconds if no inclusion nor exclusion. * Short press (each button, <1 second): - The green LED will flash once and send “Scene Activation” command to the 5. Factory Default Reset: nodes of corresponding group. Press 4 buttons together for 10 seconds. The LED colors will turn red after 2 - Corresponding Scene ID and Group: seconds for 2 seconds and turn green for another 2 seconds. Keyfob will send “Device Reset Locally Notification” command and reset to the factory default. (Red Button 1 Button 2 Button 3 Button 4 LED flashes fast means reset completely). Group 2 3 4 5 Remark: This is to be used only in the case of primary controller being Scene ID 1 3 5 7 inoperable or otherwise unavailable. * Long press (each button): 6. Copy Network Data to another Controller - The red LED will flash once and send “Scene Activation” command to the This functionality cannot be triggered by user, but is automatic issued under two nodes of corresponding group. circumstances when DUT acts as a primary controller: - Corresponding Scene ID and Group: A) Include another controller into network. B) Controller Shift, hand over primary role to another controller. Button 1 Button 2 Button 3 Button 4 Group 2 3 4 5 Scene ID 2 4 6 8 7. Support OTA Firmware Update. 4. Setup Mode (DIP SWITCH TO LEFT): 8. All the rest unaddressed commands followed Z-WAVE standard. 1) Include other devices into Keyfob's network: * Keyfob must be primary controller ‫ى‬ ‫ﻰ‬


Document Created: 2019-09-06 12:56:37
Document Modified: 2019-09-06 12:56:37
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC