Users Manual

FCC ID: KFR-ZS5101US-5

Users Manual

Download: PDF
FCCID_2877188

Federal Communications Commission Statement This equipment has been followed to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interferene by one of the following measures: Reorient or relocate the receiving antenna, Increase the separation between the equipment and receiver, Connect the equipment into and outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undersired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. Limited Warranty Vision Guarantees that every wireless shock sensor is free from physical defects in material and workmanship under normal use for one year from the date of purchase. If the product proves defective during this one-year warranty period, Vision will replace it free of charge. Vision does not issue any refunds. This warranty is extended to the original end user purchase only and is not transferable. This warranty does not apply to : (1) damage to units caused by accident, dropping or Installation & Operation Manual abuse in handling, or any negligent use; (2) units which have been subject to unauthorized repair, taken apart, or otherwise modified; (3) units not used in accordance with instruction; (4) damages exceeding the cost of the product; (5) transit damage, initial installation costs, removal cost, or reinstallation cost. ZS5101IN-5 For information on addional devices, plesae visit us at www.visionsecurity.com.tw ZS5101MY-5 ZS5101EU-5 ZS5101RU-5 ZS5101US-5 ZS5101IL-5 ZS5101KR-5 ZS5101HK-5 ZS5101JP-5 ZS5101BR-5 Wireless Shock Sensor -5- ZS 5101-5 V0 1031223 6B1Z-51002

Z—Wave Command Classes: Introduction COMMAND_CLASS_ASSOCIATION_GRP_INFO COMMAND_CLASS_ASSOCIATION_V2 Thanks for choosing the Vision‘s wireless shock sensor of the home security device. This COMMAND_CLASS_BATTERY sensor is a Z—Wave"" enabled device (interoperable, two—way RF mesh networking COMMAND_CLASS_DEVICE_RESET_LOCALLY technology) and is fully compatible with any Z—Wave"* enabled network and its‘ security COMMAND_CLASS—FIRMWARE_UPDATE_MD_V2 COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2 framework. Every mains powered Z—Wave enabled device acts as a signal repeater and COMMAND_CLASS_NOTIFICATION_V4 multiple devices result in more possible transmission routes which helps eliminate "RF COMMAND_CLASS_POWERLEVEL dead—spots" COMMAND_CALSS_SECURITY Z—Wave"" enabled devices displaying the Z—Wave"" logo can also be used with it COMMAND_CLASS_VERSION_V2 regardless of the manufacturer, and ours can also be used in other manufacturer‘s COMMAND_CLASSWAKE_UP_V2 COMMAND_CLASS_ZWAVEPLUS_INFO_V2 Z—Wave"" enabled networks. This sensor detects the vibrations made by an intruder trying to break a window or door, and also detect tampersituations, it will send Z—Wave"* signal when vibrations or tampersituations are detected. When the device is secure Alarm Version 1 |Notification Version 4 included into Z—Wave network, above the communication will be encrypted. Product Description and Specification Vibration detected 0x02 Alarm Type Tamper Switch 0x03 *** For indoor use only *** Program / Tamper Switch Alarm Level ON : OxPF OFF: 0x00 Sensitivity djustment Bracket Holder Notification Vibration detected 0x07 LED Type Tamper Switch 0x07 . . ON : 0x02 Notification |_Vibration detected OFF: 0x00 Event . Open:0x03 Tamper Switch Glose:0x00 Event Vibration detected 0x02 Specification: Package Content Protocol: Z—Wave" (ZM5202) 1pc Z8 5101—5 Shock sensor Parameter Tamper Switch 0x03 Frequency Range: 1pe Bracket Holder Installation 865.22MHz (ZS5101N—5) 1pe Adhesive tape for sensor Notice: If you are installing the entire Z—Wave"*‘ system for the first time, please refer to 868.10MHz (ZS5101MY—5 3pc Screw the installation guide of Z—Wave * Interface Controller before installing Z8 5101—5 Shock 868.42MHz (ZS5101EU—5 1pc CR123A Lithium Battery Sensor. 869.00MHz (ZS5101RU—5 1pc Installation & Operation 1. Install Battery: Use care when installing the battery. Press the locking tab on the top 908.42MHz (2S5101US—5 Manual sensor cover, and then gently pull up the cover. Observe the correct polarity before 916.00MHz (ZS51011L—5) insert the battery. 919~923MHz (ZS5101KR—5) 2. After insert the battery, the LED will start to flash slowly, which means the sensor 919.80MHz (ZS5101HK—5) has not yet been "inclusion" 922~926MHz (ZS5101JP—5) 3. For "Inclusion" in (adding to) a network: Put the Z—Wave"" Interface Controller 921.42MHz (ZS5101BR—5) into "inclusion" mode, and following its instruction to add the Z8 5101—5 to your Operating Range: Up to 100 feet line of sight controller. To get in the "inclusion‘ mode, the distance between sensor and Operating Temp.: —15°C~ 60°C (5°F~140°F} controller is suggested to be in one meter. Press the program switch of Z5 5101—5 for 1 second at least to be included. The LED on the ZS 5101—5 should go off, if not, Battery: Panasonic CR123A * 1PC please try again. 12.

For "Exclusion" from (removing from) a network: Put the Z—Wave"" Interface 12. Using the adhesive tape or fixing screws to fix the bracket holder with shock sensor. Controller into "exclusion" mode, and following its instruction to delete the ZS 5101—5 from your controller. Press the program switch of ZS 5101—5 for 1 second 13. Sensitivity Adjustment: at least to be excluded. To increase sensitivity, turn the adjustment clockwise. To decrease sensitivity, turn the adjustment counter—clockwise. For "Association" :removing the cover of the ZS 5101—5 to get into the "Awake" mode, then put the Z—Wave"" Interface Controller into "Association", and following Use Screws or Adhesive Tape its instruction to associate the ZS 5101 with other device. Close the cover back after "association" done, afterward the ZS 5101 —5 will get into "Sleep" mode for power saving. Support one association group (5 nodes). All triggering reports & low voltage report will be sent to the associated nodes. "Awake" mode: it is to leave the "Sleep" mode by removing the cover of ZD5101—5, to allow the Z—Wave"" Interface Controller to do "Inclusion", "Exclusion", "Association" and to reply and receive the commands from controller. Auto Wake Up: Use "Wake Up" command to set up the awaking time and send the wake up notification to controller. User can use command to change the auto wake up from 500 seconds to 1 week, Interval increment is 250 seconds. (Default: 6 hours) 1. Vibrate the ZS 5101, the sensor will send status of "ON" (Basic Set,Value:O0xFF) & * Use "Battery Get" command to have the battery capacity back in % notification report to any association nodes ; With no triggered in 10 seconds, the senor will send status of "OFF"(Basic Set,Value:0x00) & notification report to any 5. Battery Capacity Detection: association nodes.Normal operation, the LED will not light. * It will detect the battery capacity automatically 2. The ZS 5101 sensor equipped with tamper switch. If the cover of sensor is removed, * Low Battery Auto Report (low battery is set as 2.64+/—0.1 Voltage, detects every 2 the ZS 5101 will send an notification report to the Z—Wave"? Interface Controller. hours) Power Level Control: Use "Power Level Set" to set up the RF strength * Use "Power Level Test Node Set" to test specific node‘s RF sensitivity * Support AES Function Support OTA Firmware update from controller. Please refer to your controller manual. Once OTA function success, please make sure to exclusive the device & inclusive again before use the device. Factory Default Reset: Push the Tamper switch then power on (put in the battery) & hold the Tamper switch for 5 seconds, 2ZD5101—5 will send the "Device Reset Locally Notification" command and reset to the factory default, LED will solid on, need to take off the battery and re—put in the battery to complete the function. 10. All the rest commands depend on Z—Wave standard 11. Slide back the rear cover and screw fastening with the front cover, the LED should go off.


Document Created: 2014-12-23 17:10:30
Document Modified: 2014-12-23 17:10:30
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC