Users Manual-1

FCC ID: KFR-ZP3111US-5

Users Manual

Download: PDF
FCCID_2905251

Federal Communications Commission Statement This equipment has been followed to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interferene by one of the following measures: - Reorient or relocate the receiving antenna, - Increase the separation between the equipment and receiver, - Connect the equipment into and outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must Installation & Operation Manual accept any interference received, including interference that may cause undersired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. ZP3111IN-5 ZP3111MY-5 Limited Warranty ZP3111EU-5 Vision Guarantees that every wireless PIR sensor is free from physical defects in material and workmanship under normal use for one year from the date of purchase. If the product ZP3111RU-5 proves defective during this one-year warrany period, Vision will replace it free of charge. ZP3111US-5 Vision does not issue any refunds. This warnnty is extended to the original end user purchase only and is not transferable. This warranty does not apply to : (1) damage to units ZP3111IL-5 caused by accident, dropping or abuse in handling, or any negligent use; (2) units which ZP3111KR-5 have been subject to unauthorized repair, taken apart, or otherwise modified; (3) units not ZP3111HK-5 used in accordance with instruction; (4) damanges exceeding the cost of the produt; (5) transit damage, initial installation costs, removal cost, or reinstallation cost. ZP3111JP-5 For information on addional devices, plesae visit us at www.visionsecurity.com.tw ZP3111BR-5 4-in-1 Motion Sensor (Temp./Humidity/Light Sensor Built-In) ZP 3111-5 V0 1040702 6B1Z-31003

Introduction Thanks for choosing the Vision’s wireless 4-in-1 Motion sensor of the home security device. The new multi-sensor consists of motion, temperature, humidity & light sensor for combing several functionality in one device; more attractive and economic consideration. This TM sensor is a Z-Wave enabled device (interoperable, two-way RF mesh networking TM technology) and is fully compatible with any Z-Wave enabled network and it’s security TM framework. Every mains powered Z-Wave enabled device acts as a signal repeater and multiple devices result in more possible transmission routes which helps eliminate “RF dead-spots”. Z-Wave TM enabled device displaying the Z-Wave TM logo can also be used with it (C) - Ceiling (D) – Vertical (E) - Angled regardless of the manufacturer, and ours can also be used in other manufacturer’s Z-Wave TM TM enabled networks. This sensor monitors movement, and send Z-Wave signal when movement is detected inside the building. With Temperature sensor built inside, it will (Installation for Information) send the signal out when temperature changed. When the device is secure included into Z-Wave network, above communication will be encrypted. Specification: Package Content: Product Description and Specification Protocol: Z-Wave™ (ZM5202) 1pc ZP 3111 Multi-Sensor Frequency Range: *** For indoor use only *** 1pc Adhesive tape for sensor 865.22MHz (ZP3111IN-5) 868.10MHz (ZP3111MY-5) 2pc AAA Alkaline Battery 868.42MHz (ZP3111EU-5) 1pc Installation & Operation Manual 869.00MHz (ZP3111RU-5) 908.42MHz (ZP3111US-5) 916.00MHz (ZP3111IL-5) 919.80MHz (ZP3111HK-5) 920.00MHz~923.00MHz (ZP3111KR-5) 922.00MHz~926.00MHz (ZP3111JP-5) 921.42MHz (ZP3111BR-5) Operating Range: Up to 100 feet line of sight Operating Temp.: -10°C~ 40°C (5°F~104°F) Battery: AAA x 2 Z-Wave Command Classes: COMMAND_CLASS_ASSOCIATION_GRP_INFO COMMAND_CLASS_ASSOCIATION_V2 COMMAND_CLASS_BATTERY COMMAND_CLASS_CONFIGURATION COMMAND_CLASS_DEVICE_RESET_LOCALLY COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2 COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2 COMMAND_CLASS_NOTIFICATION_V4 COMMAND_CLASS_POWERLEVEL COMMAND_CLASS_SECURITY COMMAND_CLASS_SENSOR_MULTILEVEL_V7 (A) – Wall Corner (B) – Table COMMAND_CLASS_VERSION_V2 COMMAND_CLASS_WAKE_UP_V2 COMMAND_CLASS_ZWAVEPLUS_INFO_V2 -1- -2-

Configuration – Temperature Installation Notice: If you are installing the entire Z-Wave TM system for the first time, please refer to the Size VALUE Default installation guide of Z-Wave TM Interface Controller before installing ZP3111. °C 0x00 °C(0x00) 1. Release cover tab to open the cover and insert two AAA battery into the battery Parameter 1 1 compartment and close the cover back to sensor. °F 0x01 1~50 (Set up from 2. Press the program switch, the LED will flash 5 times which means the sensor has not been Parameter 2 1 1 (°C) “included” yet or flash once which means the sensor has been “included” already. 0.1°C~5°C) 3. For “Inclusion (Auto-Inclusion)” in (adding to) a network: To add the ZP3111 to your Configuration – Humidity Z-Wave network (inclusion), place your Z-Wave primary controller into inclusion mode and the distance between sensor and controller is suggested to be in one meter. Press the Program Switch of ZP3111 for sending the NIF. After sending NIF, Z-Wave will send the Size VALUE Default auto inclusion, otherwise, ZP3111 will go to sleep after 20 seconds. 1~50 (Set up from 4. For “Exclusion” from (removing from) a network: To remove the ZP3111 from your Parameter 3 1 10% 1%~50%) Z-Wave network (exclusion), place your Z-Wave primary controller into “exclusion” mode, and following its instruction to delete the ZP3111 to your controller. Press the Program Configuration – Light Switch of ZP3111 once to be excluded. For “Association”: Press the program switch for sending NIF, the LED will flash once and send the Wake Up Notification in 5 seconds. Put the Z-Wave TM Interface Controller into Size VALUE Default “association”, and following its instruction to associate the ZP3111 with other device. 0,5~50 (Set up from 0 Support grouping identifier=1. Support one association group (5 nodes). “Association” is Parameter 4 1 10% for Off or 5%~50%) used for other grouping devices chain reaction. Red LED will flash once when trigger. 5. Auto Wake Up: Configuration – Motion Sensor: Use “Wake Up” command to set up the awaking time (from 10 minutes to 1 week) and send the wake up notification to controller Size Value 6. Battery Capacity Detection: 1 ~ 255 (unsigned decimal) Minutes * Use “Battery Get” command to have the battery capacity back in % Parameter 5 1 * It will detect the battery capacity automatically (default: 3 minutes) 1~7 * Low Battery Auto Report when power is lower than 2.6V +/- 0.1V Parameter 6 1 (default: 4) 7. Temperature-If the present temperature is different with the sensor record and exceed the (Table 1) setting program, the sensor will report the present temperature. LED flash every 3 minutes to represent the temperature or wake up by press the Program SW. (Parameter 5) Re-trigger duration: User can change value from 1 to 255 minutes to setup the re-trigger time when there is no movement detected in the period of time. Default is 3 minutes. Temperature LED Color (Parameter 6) Infrared sensor sensitivity adjustment, 7 levels sensitivity, 1 = most Under 15°C Green sensitive, 7 = most insensitive, default values= 4 15~23°C Blue 23~28°C Yellow/YellowGreen Configuration – LED Mode: 28~36°C Purple Value Over 36°C Red Size (Default: Mode 3) 1 ~ 3 (Mode 1 ~ Mode 3) Multilevel Sensor Report Mode 1  LED Turn Off (Both Temp./PIR Trigger) Parameter 7 1 Mode 2  Temp. (Breathing Light Mode) Sensor Type 0x01 PIR (Quick Flash) 0x00 (°C) Scale Mode 3  LED Quick Flash (Temp./PIR Trigger) 0x01 (°F) (Caution: Mode 2 will shorten the battery life due to the Breathing Light Mode.) Size and Precision 2 -3- -4-

8. Humidity Report- If the present humidity is different with the sensor record and exceed the setting program, the sensor will report the present humidity. Operation 1. Using adhesive tape to mount ZP3111 at 2 meters above surface. To enhance proper Multilevel Sensor Report operation, place ZP3111 on the location which can detect the room widely. Sensor Type 0x05 2. Walk in front of ZP3111, sensor will send Basic set On (0xFF) , Red LED willl flash Scale 0x00 (%) once and please refer to status report as table below. Size and Precision 2 3. If no movement detected in three minutes (default is 3 minutes - based on user’s configuration setting, refer Table 1 (Parameter 5) will send Basic Set OFF (0x00), Red 9. Light Report- If the present illumination is different with the sensor record and exceed the LED will flash once, and refer to table for status. setting program, the sensor will report the present illumination. 4. The ZP3111 sensor equipped with tamper switch. If the tamper switch is triggered (or Multilevel Sensor Report remove the cover), the ZP3111 sensor will send Alarm Report, LED will flash once and Sensor Type 0x03 refer to table for status. Scale 0x00 (%) 5. If the tamper switch is closed (or closed the cover), ZP3111 will send Alarm Report, Size and Precision 2 and refer to table for status. 10. Factory Default Reset: Remove cover to trigged tamper switch, LED flash once & send out Alarm Report. Press Program Switch 10 times within 10 seconds, ZP3111 will send the “Device Alarm V1 Notification V4 Notification V4 Reset Locally Notification” command and reset to the factory default. (Remark: This is to be used (Movement & Tamper only in the case of primary controller being inoperable or otherwise unavailable.) (Movement) (Tamper Switch) Switch) Alarm Type 0x07 0x00 (No movement after 3 mins) Alarm Level 0xFF (Motion detected) Notification Type 0x07 0x07 0x08(Motion Notification Detected)/ 0x03(remove cover)/ Event 0x00 (no movement 0x00 (cover closed) after 3 mins) Notification 0x08 0x03 Event Parameter 6. Support OTA Firmware update from controller. Please refer to your controller manual and use COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2. To proceed the OTA process. Once OTA function success, please make sure to exclude the device & 11. All the rest commands depend on Z-Wave standard. include again before using the device. -5- -6-


Document Created: 2015-07-03 11:14:35
Document Modified: 2015-07-03 11:14:35
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC