Test Report

FCC ID: KFR-ZM1601US

Test Report

Download: PDF
FCCID_2521618

Compliance Certification Services Inc. FCC ID: KFR-ZM1601US Report No.: T150126N06-RP1 FCC 47 CFR PART 15 SUBPART C: 2013 ANSI C63.10: 2013 TEST REPORT For Z-Wave Wireless Siren Model: ZM1601US Brand: Issued to Vision Automobile Electronics Industrial Co., Ltd. No. 78, Gongye 3rd Rd.,Technology Industrial Park,Tainan City 70955, Taiwan (R.O.C.) Issued by Compliance Certification Services Inc. Tainan Lab. No.8,Jiucengling, Xinhua Dist., Tainan City 712, Taiwan (R.O.C.) TEL: (06) 580-2201 FAX: (06) 580-2202 Issued Date: January 29, 2015 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. Page 1 / 30

Compliance Certification Services Inc. FCC ID: KFR-ZM1601US Report No.: T150126N06-RP1 REVISION HISTORY Rev. Issue Date Revisions Effect Page Revised By 00 January 29, 2015 Initial Issue ALL Sunny Chang Page 2 / 30

Compliance Certification Services Inc. FCC ID: KFR-ZM1601US Report No.: T150126N06-RP1 TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION .........................................................................4 2. EUT DESCRIPTION..............................................................................................5 3. TEST METHODOLOGY........................................................................................6 3.1 EUT CONFIGURATION ...................................................................................6 3.2 EUT EXERCISE ...............................................................................................6 3.3 GENERAL TEST PROCEDURES....................................................................6 3.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS ........................7 3.5 DESCRIPTION OF TEST MODES...................................................................7 4. INSTRUMENT CALIBRATION .............................................................................8 4.1 MEASURING INSTRUMENT CALIBRATION ..................................................8 4.2 MEASUREMENT EQUIPMENT USED ............................................................8 4.3 MEASUREMENT UNCERTAINTY ...................................................................9 5. FACILITIES AND ACCREDITATIONS ...............................................................10 5.1 FACILITIES ....................................................................................................10 5.2 EQUIPMENT ..................................................................................................10 5.3 LABORATORY ACCREDITATIONS LISTING ...............................................10 5.4 TABLE OF ACCREDITATIONS AND LISTINGS............................................11 6. SETUP OF EQUIPMENT UNDER TEST ............................................................12 6.1 SETUP CONFIGURATION OF EUT ..............................................................12 6.2 SUPPORT EQUIPMENT................................................................................12 7. FCC PART 15.249 REQUIREMENTS ................................................................13 7.1 20 DB BANDWIDTH.......................................................................................13 7.2 BAND EDGES MEASUREMENT ...................................................................16 7.3 DUTY CYCLE.................................................................................................17 7.4 SPURIOUS EMISSION ..................................................................................19 7.5 POWERLINE CONDUCTED EMISSIONS .....................................................28 APPENDIX I - PHOTOGRAPHS OF TEST SETUP .................................................29 APPENDIX II - PHOTOGRAPHS OF EUT .............................................................. A1 Page 3 / 30

Compliance Certification Services Inc. FCC ID: KFR-ZM1601US Report No.: T150126N06-RP1 1. TEST RESULT CERTIFICATION Product: Z-Wave Wireless Siren Model: ZM1601US Brand: Applicant: Vision Automobile Electronics Industrial Co., Ltd. No. 78, Gongye 3rd Rd.,Technology Industrial Park,Tainan City 70955, Taiwan (R.O.C.) Manufacturer: Vision Automobile Electronics Industrial Co., Ltd. No. 78, Gongye 3rd Rd.,Technology Industrial Park,Tainan City 70955, Taiwan (R.O.C.) Tested: January 16, 2015 APPLICABLE STANDARDS STANDARD TEST RESULT FCC 47 CFR Part 15 Subpart C: 2013 No non-compliance noted ANSI C63.10 : 2013 We hereby certify that: The above equipment was tested by Compliance Certification Services Inc. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4: 2009 and the energy emitted by the sample EUT tested as described in this report is in compliance with the requirements emission limits of FCC Rules Part 15.107, 15.109,15.207, 15.209 and 15.249. The test results of this report relate only to the tested sample identified in this report. Approved by: Reviewed by: Jeter Wu Eric Huang Assistant Manager Assistant Section Manager Page 4 / 30

Compliance Certification Services Inc. FCC ID: KFR-ZM1601US Report No.: T150126N06-RP1 2. EUT DESCRIPTION Product Z-Wave Wireless Siren Model Number ZM1601US Brand Name Received Date January 16, 2015 Frequency Range 908.42MHZ ± 20kHz Transmit Peak Power 89.10 dBμV/m Data Rate 9.6 kbps , 40kbps Number of Channels 1 Channel Type of Modulation FSK Power Supply 4pcs x AA Energizer Batteries PCB antenna Antenna Type Model: ZM1601US Gain: -10 dBi RF Module Model ZW0301 Temperature Range -15°C ~ +60°C Remark: 1. Client consigns only one model sample to test (Model Number: ZM1601US). Therefore, the testing Lab. just guarantees the unit, which has been tested. 2. This submittal(s) (test report) is intended for FCC ID: KFR-ZM1601US filing to comply with Section 15.107 & 15.109 (FCC Part 15, Subpart B) and Section 15.207, 15.209, 15.249. Page 5 / 30

Compliance Certification Services Inc. FCC ID: KFR-ZM1601US Report No.: T150126N06-RP1 3. TEST METHODOLOGY The tests documented in this report were performed in accordance with ANSI C63.4 and FCC CFR 47 2.1046, 2.1047, 2.1049, 2.1051, 2.1053, 2.1055, 2.1057, 15.207, 15.209 and 15.249. 3.1 EUT CONFIGURATION The EUT configuration for testing is installed on RF field strength measurement to meet the Commissions requirement and operating in a manner that intends to maximize its emission characteristics in a continuous normal application. 3.2 EUT EXERCISE The EUT was operated in the engineering mode to fix the TX frequency that was for the purpose of the measurements. According to its specifications, the EUT must comply with the requirements of the Section 15.107 and 15.109 under the FCC Rules Part 15 Subpart B and Section 15.207, 15.209, 15.249 under the FCC Rules Part 15 Subpart C. 3.3 GENERAL TEST PROCEDURES Conducted Emissions The EUT is placed on the turntable, which is 0.8 m above ground plane. According to the requirements in Section 13.1.4.1 of ANSI C63.4 Conducted emissions from the EUT measured in the frequency range between 0.15 MHz and 30MHz using CISPR Quasi-peak and average detector modes. Radiated Emissions The EUT is placed on a turn table, which is 0.8 m above ground plane. The turntable shall rotate 360 degrees to determine the position of maximum emission level. EUT is set 3m away from the receiving antenna, which varied from 1m to 4m to find out the highest emission. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. In order to find out the maximum emissions, exploratory radiated emission measurements were made according to the requirements in Section 13.1.4.1 of ANSI C63.4. Page 6 / 30

Compliance Certification Services Inc. FCC ID: KFR-ZM1601US Report No.: T150126N06-RP1 3.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS 1. Except as shown in paragraph (d) of this section, only spurious emissions are permitted in any of the frequency bands listed below: MHz MHz MHz GHz 0.090 - 0.110 16.42 - 16.423 399.9 - 410 4.5 - 5.15 1 0.495 - 0.505 16.69475 - 16.69525 608 - 614 5.35 - 5.46 2.1735 - 2.1905 16.80425 - 16.80475 960 - 1240 7.25 - 7.75 4.125 - 4.128 25.5 - 25.67 1300 - 1427 8.025 - 8.5 4.17725 - 4.17775 37.5 - 38.25 1435 - 1626.5 9.0 - 9.2 4.20725 - 4.20775 73 - 74.6 1645.5 - 1646.5 9.3 - 9.5 6.215 - 6.218 74.8 - 75.2 1660 - 1710 10.6 - 12.7 6.26775 - 6.26825 108 - 121.94 1718.8 - 1722.2 13.25 - 13.4 6.31175 - 6.31225 123 - 138 2200 - 2300 14.47 - 14.5 8.291 - 8.294 149.9 - 150.05 2310 - 2390 15.35 - 16.2 8.362 - 8.366 156.52475 - 2483.5 - 2500 17.7 - 21.4 8.37625 - 8.38675 156.52525 2655 - 2900 22.01 - 23.12 8.41425 - 8.41475 156.7 - 156.9 3260 - 3267 23.6 - 24.0 12.29 - 12.293 162.0125 - 167.17 3332 - 3339 31.2 - 31.8 12.51975 - 12.52025 167.72 - 173.2 3345.8 - 3358 36.43 - 36.5 12.57675 - 12.57725 240 - 285 3600 - 4400 ( 2) 13.36 - 13.41 322 - 335.4 1 Until February 1, 1999, this restricted band shall be 0.490-0.510 MHz. 2 Above 38.6 2. Except as provided in paragraphs (d) and (e), the field strength of emissions appearing within these frequency bands shall not exceed the limits shown in Section 15.209. At frequencies equal to or less than 1000 MHz, compliance with the limits in Section 15.209 shall be demonstrated using measurement instrumentation employing a CISPR quasi-peak detector. Above 1000 MHz, compliance with the emission limits in Section 15.209 shall be demonstrated based on the average value of the measured emissions. The provisions in Section 15.35 apply to these measurements. 3.5 DESCRIPTION OF TEST MODES The EUT ( Model: ZM1601US ) had been tested under engineering test mode condition and the EUT staying in continuous transmitting mode. Note： The field strength of spurious emission was measured in the following position: 1) EUT has supported two data rates ( 9.6kbps , 40kbps) which have been the test. The worst emission was found in 9.6kbps and the worst case was recorded. 2) The field strength of spurious emission was measured in the following position: EUT stand-up position (Y axis), lie-down position (X, Z axis). The worst emission was found in s lie-down position (X axis) and the worst case was recorded. Page 7 / 30

Compliance Certification Services Inc. FCC ID: KFR-ZM1601US Report No.: T150126N06-RP1 4. INSTRUMENT CALIBRATION 4.1 MEASURING INSTRUMENT CALIBRATION The measuring equipment, which was utilized in performing the tests documented herein, has been calibrated in accordance with the manufacturer's recommendations for utilizing calibration equipment, which is traceable to recognized national standards. 4.2 MEASUREMENT EQUIPMENT USED Equipment Used for Emissions Measurement Open Area Test Site # 6 Name of Equipment Manufacturer Model Serial Number Calibration Due TYPE N COAXIAL CABLE SUHNER CHA9513 6 JAN. 20, 2016 BI-LOG Antenna Sunol JB1 A070506-2 AUG. 17, 2015 LOOP ANTENNA EMCO 6502 8905-2356 JUN. 10, 2015 Pre-Amplifier HP 8447F 2944A03817 FEB.13, 2015 Pre-Amplifier EMCI EMC 012645 980098 DEC. 04, 2015 EMI Receiver R&S ESVS10 833206/012 JUN. 29, 2015 Horn Antenna Com-Power AH-118 071032 JAN. 09, 2016 3116 Double Ridge Antenna ETS-LINDGREN 3116 00078900 FEB. 23, 2015 (40G) Turn Table Yo Chen 001 ---------- N.C.R. Antenna Tower AR TP1000A 309874 N.C.R. Controller CT SC101 ---------- N.C.R. E-INSTRUMENT RF Swicth ERS-180A EC1204141 N.C.R TELH LTD Spectrum Analyzer R&S FSU 200789 JUL. 01, 2015 Spectrum Analyzer R&S FSEM 830270/015 NCR Spectrum Analyzer R&S FSEK 30 100264 JAN. 26, 2016 Remark: Each piece of equipment is scheduled for calibration once a year. Page 8 / 30

Compliance Certification Services Inc. FCC ID: KFR-ZM1601US Report No.: T150126N06-RP1 4.3 MEASUREMENT UNCERTAINTY Parameter Uncertainty Radiated Emission, 30 to 200 MHz ±3.21dB Test Site : OATS-6 Radiated Emission, 200 to 1000 MHz ±3.09dB Test Site : OATS-6 Radiated Emission, 1 to 8 GHz ± 2.65dB Radiated Emission, 8 to 18 GHz ± 2.69dB Radiated Emission, 18 to 26.5 GHz ± 2.65dB Radiated Emission, 26 to 40 GHz ± 3.03dB Power Line Conducted Emission ± 1.91dB Uncertainty figures are valid to a confidence level of 95%, k=2 Page 9 / 30

Compliance Certification Services Inc. FCC ID: KFR-ZM1601US Report No.: T150126N06-RP1 5. FACILITIES AND ACCREDITATIONS 5.1 FACILITIES All measurement facilities used to collect the measurement data are located at No.8,Jiucengling, Xinhua Dist., Tainan City 712, Taiwan (R.O.C.) The sites are constructed in conformance with the requirements of ANSI C63.7:1992, ANSI C63.4 : 2014 and CISPR Publication 22. 5.2 EQUIPMENT Radiated emissions are measured with one or more of the following types of linearly polarized antennas: tuned dipole, biconical, log periodic, bi-log, and/or ridged waveguide, horn. Spectrum analyzers with pre-selectors and quasi-peak detectors are used to perform radiated measurements. Conducted emissions are measured with Line Impedance Stabilization Networks and EMI Test Receivers. Calibrated wideband preamplifiers, coaxial cables, and coaxial attenuators are also used for making measurements. All receiving equipment conforms to CISPR Publication 16-1, “Radio Interference Measuring Apparatus and Measurement Methods.” 5.3 LABORATORY ACCREDITATIONS LISTING The test facilities used to perform radiated and conducted emissions tests are accredited by Taiwan Accreditation Foundation for the specific scope of accreditation under Lab Code: 1109 to perform Electromagnetic Interference tests according to FCC PART 15 AND CISPR 22 requirements. No part of this report may be used to claim or imply product endorsement by TAF or any agency of the Government. In addition, the test facilities are listed with Federal Communications Commission (registration no: TW-1037). Page 10 / 30

Compliance Certification Services Inc. FCC ID: KFR-ZM1601US Report No.: T150126N06-RP1 5.4 TABLE OF ACCREDITATIONS AND LISTINGS Our laboratories are accredited and approved by the following accreditation body according to ISO/IEC 17025. Taiwan TAF The measuring facility of laboratories has been authorized or registered by the following approval agencies. Canada Industry Canada Germany TUV NORD Taiwan BSMI USA FCC Copies of granted accreditation certificates are available for downloading from our web site, http:///www.ccsrf.com Page 11 / 30

Compliance Certification Services Inc. FCC ID: KFR-ZM1601US Report No.: T150126N06-RP1 6. SETUP OF EQUIPMENT UNDER TEST 6.1 SETUP CONFIGURATION OF EUT See test photographs attached in Appendix I for the actual connections between EUT and support equipment. 6.2 SUPPORT EQUIPMENT 【RF】 No. Product Manufacturer Model No. Certify No. Signal cable 1 N/A --- --- --- --- No. Signal cable description A N/A --- 【EMC】 No. Product Manufacturer Model No. Certify No. Signal cable 1 N/A --- --- --- --- No. Signal cable description A N/A --- Remark: 1. All the equipment/cables were placed in the worst-case configuration to maximize the emission during the test. 2. Grounding was established in accordance with the manufacturer’s requirements and conditions for the intended use. 6.3 EUT OPERATING CONDITION RF Setup 1. Set up a whole system as the setup diagram. 2. Turn on power. Page 12 / 30

Compliance Certification Services Inc. FCC ID: KFR-ZM1601US Report No.: T150126N06-RP1 7. FCC PART 15.249 REQUIREMENTS 7.1 20 DB BANDWIDTH LIMIT None; for reporting purposes only. MEASUREMENT EQUIPMENT USED Open Area Test Site # 6 Name of Equipment Manufacturer Model Serial Number Calibration Due TYPE N COAXIAL CABLE SUHNER CHA9513 6 JAN. 20, 2016 BI-LOG Antenna Sunol JB1 A070506-2 AUG. 17, 2015 LOOP ANTENNA EMCO 6502 8905-2356 JUN. 10, 2015 Pre-Amplifier HP 8447F 2944A03817 FEB.13, 2015 Pre-Amplifier EMCI EMC 012645 980098 DEC. 04, 2015 EMI Receiver R&S ESVS10 833206/012 JUN. 29, 2015 Horn Antenna Com-Power AH-118 071032 JAN. 09, 2016 3116 Double Ridge ETS-LINDGREN 3116 00078900 FEB. 23, 2015 Antenna (40G) Turn Table Yo Chen 001 ---------- N.C.R. Antenna Tower AR TP1000A 309874 N.C.R. Controller CT SC101 ---------- N.C.R. E-INSTRUMENT RF Swicth ERS-180A EC1204141 N.C.R TELH LTD Spectrum Analyzer R&S FSU 200789 JUL. 01, 2015 Spectrum Analyzer R&S FSEM 830270/015 NCR Spectrum Analyzer R&S FSEK 30 100264 JAN. 26, 2016 Spectrum Analyzer Agilent N9010A MY522213344 MAY 16, 2015 Remark: Each piece of equipment is scheduled for calibration once a year. Page 13 / 30

Compliance Certification Services Inc. FCC ID: KFR-ZM1601US Report No.: T150126N06-RP1 Test Configuration Antenna tower 3m Bi-log antenna EUT 4m Spectrum analyzer Turntable 1m 0.8m Reference ground plane TEST PROCEDURE 1. The EUT is placed on a turntable, which is 0.8m above ground plane. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find out the highest emissions. 4. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 5. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 6. Set the spectrum analyzer in the following setting as: RBW is set to 10 kHz and VBW is set 300kHz. TEST RESULTS No non-compliance noted. Test Data Frequency 20 dB Bandwidth Modulation (MHz) (kHz) 9.6kbps 908.42 68.73 Page 14 / 30

Compliance Certification Services Inc. FCC ID: KFR-ZM1601US Report No.: T150126N06-RP1 Test Plot 9.6kbps Mode Page 15 / 30

Compliance Certification Services Inc. FCC ID: KFR-ZM1601US Report No.: T150126N06-RP1 7.2 BAND EDGES MEASUREMENT LIMIT 1. In the above emission table, the tighter limit applies at the band edges. Frequency Field Strength Field Strength (MHz) (μV/m at 3-meter) (dBμV/m at 3-meter) 30-88 100 40 88-216 150 43.5 216-960 200 46 Above 960 500 54 2. As shown in Section 15.35(b), for frequencies above 1000 MHz, the above field strength limits in paragraphs (a) and (b) of this section are based on average limits. However, the peak field strength of any emission shall not exceed the maximum permitted average limits specified above by more than 20 dB under any condition of modulation. For point-to-point operation under paragraph (b) of this section, the peak field strength shall not exceed 2500 millivolts/meter at 3 meters along the antenna azimuth. TEST CONFIGURATION Antenna tower 3m Horn antenna EUT 4m Spectrum analyzer Turntable 1m 0.8m Pre-amp TEST PROCEDURE 1. The EUT is placed on a turntable, which is 0.8m above the ground plane. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find out the highest emission. 4. Set the spectrum analyzer in the following setting in order to capture the lower and upper band-edges of the emission: (a) PEAK: RBW=VBW=1MHz / Sweep=AUTO (b) AVERAGE: Peak Level + Duty Factor 5. Repeat the procedures until all the PEAK and AVERAGE versus polarization are measured. TEST RESULTS ※ After estimate 20dB bandwidth of 1st and last channel ,the declared frequency will not invade restrict band. There is no requirement for this test. Page 16 / 30

Compliance Certification Services Inc. FCC ID: KFR-ZM1601US Report No.: T150126N06-RP1 7.3 DUTY CYCLE LIMIT Nil (No dedicated limit specified in the Rules) MEASUREMENT EQUIPMENT USED Name of Equipment Manufacturer Model Serial Number Calibration Due Spectrum Analyzer Agilent N9010A MY522213344 MAY 16, 2015 Remark: Each piece of equipment is scheduled for calibration once a year. TEST CONFIGURATIONS Antenna tower 3m Bi-log antenna EUT 4m Spectrum analyzer Turntable 1m 0.8m Reference ground plane TEST PROCEDURE 1. Place the EUT on the table and set it in transmitting mode. 2. Set center frequency of spectrum analyzer = operating frequency. 3. Set the spectrum analyzer as RBW, VBW=100KHz, Span = 0Hz, a suitable Sweep Time. 4. Repeat above procedures until all frequency measured were complete. TEST RESULTS No non-compliance noted. Page 17 / 30

Compliance Certification Services Inc. FCC ID: KFR-ZM1601US Report No.: T150126N06-RP1 TEST DATA us Times Ton Total Ton time(ms) Ton1 100000.000 1 100000.000 100.000 Ton2 0 0.000 Ton3 0 0.000 Tp 100.000 Ton 100.000 Tp(Ton+Toff) 100.000 Duty Cycle 1.000 100 % Duty Factor 0.000 TEST PLOT Page 18 / 30

Compliance Certification Services Inc. FCC ID: KFR-ZM1601US Report No.: T150126N06-RP1 7.4 SPURIOUS EMISSION LIMIT 1. In the section 15.249(a): Except as provided in paragraph (b) of this section, the field strength of emissions from intentional radiators operated within these frequency bands shall comply with the following: Field Strength of Fundamental Field Strength of Fundamental Frequency Harmonics Field Strength (MHz) (μV/m) (mV/m) 902-928 MHz 50 500 2400 - 2483.5 MHz 50 500 5725 - 5875 MHz 50 500 24.0 - 24.25 GHz 250 2500 2. Except as provided elsewhere in this Subpart, the emissions from an intentional radiator shall not exceed the field strength levels specified in the following table: Frequency Field Strength Measurement Distance (MHz) (μV/m) (m) 30-88 100* 3 88-216 150* 3 216-960 200* 3 Above 960 500 3 Remark: Except as provided in paragraph (g), fundamental emissions from intentional radiators operating under this Section shall not be located in the frequency bands 54-72 MHz, 76-88 MHz, 174-216 MHz or 470-806 MHz. However, operation within these frequency bands is permitted under other sections of this Part, e.g., Sections 15.231 and 15.241. 3. In the above emission table, the tighter limit applies at the band edges. Frequency Field Strength Field Strength (MHz) (μV/m at 3-meter) (dBμV/m at 3-meter) 30-88 100 40 88-216 150 43.5 216-960 200 46 Above 960 500 54 Page 19 / 30

Compliance Certification Services Inc. FCC ID: KFR-ZM1601US Report No.: T150126N06-RP1 MEASUREMENT EQUIPMENT USED Open Area Test Site # 6 Name of Equipment Manufacturer Model Serial Number Calibration Due TYPE N COAXIAL CABLE SUHNER CHA9513 6 JAN. 20, 2016 BI-LOG Antenna Sunol JB1 A070506-2 AUG. 17, 2015 LOOP ANTENNA EMCO 6502 8905-2356 JUN. 10, 2015 Pre-Amplifier HP 8447F 2944A03817 FEB.13, 2015 Pre-Amplifier EMCI EMC 012645 980098 DEC. 04, 2015 EMI Receiver R&S ESVS10 833206/012 JUN. 29, 2015 Horn Antenna Com-Power AH-118 071032 JAN. 09, 2016 3116 Double Ridge ETS-LINDGREN 3116 00078900 FEB. 23, 2015 Antenna (40G) Turn Table Yo Chen 001 ---------- N.C.R. Antenna Tower AR TP1000A 309874 N.C.R. Controller CT SC101 ---------- N.C.R. E-INSTRUMENT RF Swicth ERS-180A EC1204141 N.C.R TELH LTD Spectrum Analyzer R&S FSU 200789 JUL. 01, 2015 Spectrum Analyzer R&S FSEM 830270/015 NCR Spectrum Analyzer R&S FSEK 30 100264 JAN. 26, 2016 Spectrum Analyzer Agilent N9010A MY522213344 MAY 16, 2015 Remark: Each piece of equipment is scheduled for calibration once a year. Page 20 / 30

Compliance Certification Services Inc. FCC ID: KFR-ZM1601US Report No.: T150126N06-RP1 TEST CONFIGURATION 9kHz ~ 30MHz 3m Loop antenna EUT Spectrum / Receiver Turntable 1m 0.8m Reference ground plane 30MHz ~ 1GHz Antenna tower 3m Bi-log antenna EUT 4m Spectrum analyzer Turntable 1m 0.8m Reference ground plane Page 21 / 30

Compliance Certification Services Inc. FCC ID: KFR-ZM1601US Report No.: T150126N06-RP1 Above 1 GHz Antenna (Boresight) tower Horn antenna 3m EUT 1 ~ 4m Spectrum analyzer Turntable 0.8m 30cm Pre-amp ▲▲▲▲▲▲▲▲ TEST PROCEDURE 1. The EUT is placed on a turntable, which is 0.8m above ground plane. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find out the highest emissions. 4. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 5. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 6. Set the spectrum analyzer in the following setting as: Below 1GHz: RBW=100kHz / VBW=300kHz / Sweep=AUTO Above 1GHz: (a) PEAK: RBW=VBW=1MHz / Sweep=AUTO (b) AVERAGE: Peak Level + Duty Factor 7. Repeat above procedures until the measurements for all frequencies are complete. Page 22 / 30

Compliance Certification Services Inc. FCC ID: KFR-ZM1601US Report No.: T150126N06-RP1 Below 1 GHz Operation Mode: Normal Operation Test Date: 2015/01/16 Temperature: 20.3°C Tested by: John Chen Humidity: 57°C Polarity: Ver. / Hor. Vertical Remark: 1. No emission found between lowest internal used/generated frequency to 30MHz (9kHz~30MHz). 2. Radiated emissions measured in frequency range from 30 MHz to 1000MHz were made with an instrument using peak/quasi-peak detector mode. 3. Quasi-peak test would be performed if the peak result were greater than the quasi-peak limit or as required by the applicant. 4. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 5. Margin (dB) = Remark result (dBuV/m) – Quasi-peak limit (dBuV/m). 6. That the limit for signals below 1GHz is a QP limit and peak readings are below the QP limit. 7. The fundamental signal is not shown in the test data because measurements at fundamental frequency are shown separately and were ignored during the 30 – 1000 MHz scan. Page 23 / 30

Compliance Certification Services Inc. FCC ID: KFR-ZM1601US Report No.: T150126N06-RP1 Operation Mode: Normal Operation Test Date: 2015/01/16 Temperature: 20.3°C Tested by: John Chen Humidity: 57°C Polarity: Ver. / Hor. Horizontal Remark: 1. No emission found between lowest internal used/generated frequency to 30MHz (9kHz~30MHz). 2. Radiated emissions measured in frequency range from 30 MHz to 1000MHz were made with an instrument using peak/quasi-peak detector mode. 3. Quasi-peak test would be performed if the peak result were greater than the quasi-peak limit or as required by the applicant. 4. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 5. Margin (dB) = Remark result (dBuV/m) – Quasi-peak limit (dBuV/m). 6. That the limit for signals below 1GHz is a QP limit and peak readings are below the QP limit. 7. The fundamental signal is not shown in the test data because measurements at fundamental frequency are shown separately and were ignored during the 30 – 1000 MHz scan. Page 24 / 30

Compliance Certification Services Inc. FCC ID: KFR-ZM1601US Report No.: T150126N06-RP1 The fundamental signal Operation Mode: TX / 9.6kbps Mode (X axis) Test Date: 2015/1/16 Temperature: 21.4°C Tested by: John Chen Humidity: 57% RH Polarity: Ver. / Hor. Horizontal Cable Freq. Reading AF Pre-amp Filter Level Limit Margin Mark Loss (MHz) (dBμV) (dB/m) (dB) (dB) (dB) (dBμV/m) (dBμV/m) (dB) (P/Q/A) 908.42 84.45 23.11 5.95 24.41 0.00 89.10 114.00 -24.90 P 908.42 84.45 23.11 5.95 24.41 0.00 89.10 94.00 -4.90 Q Vertical Cable Freq. Reading AF Pre-amp Filter Level Limit Margin Mark Loss (MHz) (dBμV) (dB/m) (dB) (dB) (dB) (dBμV/m) (dBμV/m) (dB) (P/Q/A) 908.42 71.96 23.11 5.95 24.41 0.00 76.61 114.00 -37.39 P 908.42 71.96 23.11 5.95 24.41 0.00 76.61 94.00 -17.39 Q Remark: Margin (dB) = Remark result (dBuV/m) – Quasi-peak limit (dBuV/m). Page 25 / 30

Compliance Certification Services Inc. FCC ID: KFR-ZM1601US Report No.: T150126N06-RP1 Above 1 GHz Operation Mode: TX / 9.6kbps Mode (X axis) Test Date: 2015/1/16 Temperature: 21.4°C Tested by: John Chen Humidity: 57% RH Polarity: Ver. / Hor. Horizontal Cable Freq. Reading AF Pre-amp Filter Level Limit Margin Mark Loss (MHz) (dBμV) (dB/m) (dB) (dB) (dB) (dBμV/m) (dBμV/m) (dB) (P/Q/A) 1816.79 60.28 29.14 2.21 48.33 0.30 43.60 74.00 -30.40 P 1816.79 59.41 29.14 2.21 48.33 0.30 42.74 54.00 -11.26 A * 2725.17 51.76 30.38 2.77 47.29 0.30 37.92 74.00 -36.08 P * 2725.17 49.27 30.38 2.77 47.29 0.30 35.43 54.00 -18.57 A * 3633.59 51.52 31.04 3.23 47.60 0.30 38.49 74.00 -35.51 P * 3633.59 48.86 31.04 3.23 47.60 0.30 35.83 54.00 -18.17 A Remark: 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 6. Margin (dB) = Remark result (dBuV/m) – Average limit (dBuV/m). Peak detector mode and average detector mode of the emission shown in Result column. Page 26 / 30

Compliance Certification Services Inc. FCC ID: KFR-ZM1601US Report No.: T150126N06-RP1 Operation Mode: TX / 9.6kbps Mod (X axis) Test Date: 2015/1/16 Temperature: 21.4°C Tested by: John Chen Humidity: 57% RH Polarity: Ver. / Hor. Vertical Cable Freq. Reading AF Pre-amp Filter Level Limit Margin Mark Loss (MHz) (dBμV) (dB/m) (dB) (dB) (dB) (dBμV/m) (dBμV/m) (dB) (P/Q/A) 1816.79 59.26 29.14 2.21 48.33 0.30 42.58 74.00 -31.42 P 1816.79 57.04 29.14 2.21 48.33 0.30 40.36 54.00 -13.64 A * 2725.18 50.62 30.38 2.77 47.29 0.30 36.77 74.00 -37.23 P * 2725.18 47.78 30.38 2.77 47.29 0.30 33.94 54.00 -20.06 A * 3633.58 48.91 31.04 3.23 47.60 0.30 35.88 74.00 -38.12 P * 3633.58 43.99 31.04 3.23 47.60 0.30 30.96 54.00 -23.04 A Remark: 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 6. Margin (dB) = Remark result (dBuV/m) – Average limit (dBuV/m). Peak detector mode and average detector mode of the emission shown in Result column. Page 27 / 30

Compliance Certification Services Inc. FCC ID: KFR-ZM1601US Report No.: T150126N06-RP1 7.5 POWERLINE CONDUCTED EMISSIONS LIMIT According to §15.207(a), except as shown in paragraphs (b) and (c) of this section, for an intentional radiator that is designed to be connected to the public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power line on any frequency or frequencies within the band 150 kHz to 30 MHz shall not exceed the limits in the following table, as measured using a 50 µH/50 ohms line impedance stabilization network (LISN). Compliance with the provisions of this paragraph shall be based on the measurement of the radio frequency voltage between each power line and ground at the power terminal. The lower limit applies at the boundary between the frequency ranges. Limits Frequency Range (dBμV) (MHz) Quasi-peak Average 0.15 to 0.50 66 to 56 56 to 46 0.50 to 5 56 46 5 to 30 60 50 Compliance with this provision shall be based on the measurement of the radio frequency voltage between each power line (LINE and NEUTRAL) and ground at the power terminals. MEASUREMENT EQUIPMENT USED Conducted Emission room #1 Name of Equipment Manufacturer Model Serial Number Calibration Due SCHWARZBECK NNLK 8130 8130124 OCT. 19, 2015 L.I.S.N. Rohde & Schwarz ESH 3-Z5 893540/015 APR. 13, 2015 TEST RECEIVER Rohde & Schwarz ESCS 30 100348 DEC. 08, 2015 BNC COAXIAL CABLE CCS BNC50 11 DEC. 04, 2015 e-3 (5.04211c) Test S/W R&S (2.27) Remark: Each piece of equipment is scheduled for calibration once a year. TEST RESULTS ※ This EUT is not connected to AC Source directly. No applicability for this test. Page 28 / 30


Document Created: 2015-02-02 17:48:57
Document Modified: 2015-02-02 17:48:57
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC