RF Test Report

FCC ID: KEAADLV

Test Report

Download: PDF
FCCID_1157630

FCC PART 90 TEST AND MEASUREMENT REPORT For Pacific Crest Corporation 510 DeGuigne Drive, Sunnyvale, CA 94085, USA FCC ID: KEAADLV Model: ADLV-1, ADLV-2 Report Type: Product type: Original Report UHF Transceiver Module Test Engineer: Dennis Huang Report Number: R0907271-90 Report Date: 2009-08-18 Boni Baniqued Reviewed By: Senior RF Engineer Prepared By: Bay Area Compliance Laboratories Corp. (84) 1274 Anvilwood Ave Sunnyvale, CA 94085, U.S.A. Tel: (408) 732-9162 Fax: (408) 732 9164 www.baclcorp.com Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP*, NIST, or any agency of the Federal Government. * This report may contain data that are not covered by the NVLAP accreditation and are marked with an asterisk “*”

Pacific Crest Corporation FCC ID: KEAADLV TABLE OF CONTENTS 1 General Information.............................................................................................................................................5 1.1 Product Description for Equipment Under Test (EUT)..................................................................................5 1.2 Mechanical Description .................................................................................................................................5 1.3 EUT Photo......................................................................................................................................................5 1.4 Objective ........................................................................................................................................................6 1.5 Related Submittal(s)/Grant(s) ........................................................................................................................6 1.6 Test Methodology ..........................................................................................................................................6 1.7 Measurement Uncertainty ..............................................................................................................................6 1.8 Test Facility....................................................................................................................................................7 2 System Test Configuration...................................................................................................................................8 2.1 Justification ....................................................................................................................................................8 2.2 EUT Exercise Software..................................................................................................................................8 2.3 Equipment Modifications...............................................................................................................................8 2.4 EUT Internal Configuration Details ...............................................................................................................8 2.5 Interface Ports and Cabling ............................................................................................................................8 2.6 Power Supply Information .............................................................................................................................8 3 Summary of Test Results......................................................................................................................................9 4 FCC §2.1091 – RF Exposure..............................................................................................................................10 4.1 Applicable Standards ...................................................................................................................................10 4.2 MPE Prediction ............................................................................................................................................10 5 FCC §2.1046 – Conducted Output Power.........................................................................................................12 5.1 Applicable Standards ...................................................................................................................................12 5.2 Test Procedure..............................................................................................................................................12 5.3 Test Results ..................................................................................................................................................12 6 FCC §2.1047 & §90.207 - Modulation Characteristic......................................................................................13 6.1 Applicable Standard .....................................................................................................................................13 6.2 Test Procedure..............................................................................................................................................13 6.3 Test Results ..................................................................................................................................................13 7 FCC §2.1049 & § 90.209 – Occupied Bandwidth and Emission Mask ...........................................................14 7.1 Applicable Standard .....................................................................................................................................14 7.2 Test Procedure..............................................................................................................................................14 7.3 Test Results ..................................................................................................................................................14 8 FCC §2.1051 & §90.210 – Spurious Emissions at Antenna Terminals...........................................................15 8.1 Applicable Standard .....................................................................................................................................15 8.2 Test Procedure..............................................................................................................................................15 8.3 Test Results ..................................................................................................................................................15 9 FCC §2.1053 & §90.210 - Radiated Spurious Emissions .................................................................................16 9.1 Applicable Standard .....................................................................................................................................16 9.2 Test Procedure..............................................................................................................................................16 9.3 Test Equipment List and Details ..................................................................................................................16 9.4 Test Setup.....................................................................................................................................................17 9.5 Test Environmental Conditions....................................................................................................................17 9.6 Summary of Test Results .............................................................................................................................18 9.7 Test Result....................................................................................................................................................18 Report Number R0907271-90 Page 2 of 35 FCC Part 90 Test Report

Pacific Crest Corporation FCC ID: KEAADLV 10 FCC §2.1055 & §90.213- Frequency Stability ..............................................................................................20 10.1 Applicable Standard .....................................................................................................................................20 10.2 Test Procedure..............................................................................................................................................20 10.3 Test Results ..................................................................................................................................................20 11 FCC §90.214 – Transient Frequency Behavior............................................................................................21 11.1 Standard Applicable .....................................................................................................................................21 11.2 Test Method .................................................................................................................................................21 11.3 Test Result....................................................................................................................................................21 12 Exhibit A - FCC Label Information..............................................................................................................22 12.1 FCC Label Requirement ..............................................................................................................................22 12.2 Proposed FCC ID Label Content .................................................................................................................22 12.3 Proposed Label Location on EUT ................................................................................................................23 13 Exhibit B – Test Setup Photographs .............................................................................................................24 13.1 Transmitter Spurious Emissions – Front View (Below 1 GHz) ...................................................................24 13.2 Transmitter Spurious Emissions – Rear View (Below 1 GHz) ....................................................................24 13.3 Transmitter Spurious Emissions – Front View (Above 1 GHz)...................................................................25 13.4 Transmitter Spurious Emissions – Rear View (Above 1 GHz)....................................................................25 14 Exhibit C - EUT Photographs .......................................................................................................................26 14.1 EUT- Top View (Vantage)...........................................................................................................................26 14.2 EUT-Bottom View (Vantage) ......................................................................................................................26 14.3 EUT- Top View (SENTRY) ........................................................................................................................27 14.4 EUT-Bottom View (SENTRY)....................................................................................................................27 14.5 EUT- Top View (TDL 450L).......................................................................................................................28 14.6 EUT-Bottom View (TDL 450L) ..................................................................................................................28 14.7 EUT–Antenna Port View (VANTAGE) ......................................................................................................29 14.8 EUT–Antenna Port View (SENTRY) ..........................................................................................................29 14.9 EUT–Antenna Port View (TDL 450L) ........................................................................................................30 14.10 EUT-AC/DC Adapter ..............................................................................................................................30 14.11 EUT – Cover off View (1): Vantage........................................................................................................31 14.12 EUT - Cover off View (2) – Without RF Shield Can: Vantage ...............................................................31 14.13 EUT – Cover off View (SENTRY) .........................................................................................................32 14.14 EUT – Cover off View (TDL 450L)........................................................................................................32 14.15 EUT – RF PCB Assembly Top View ......................................................................................................33 14.16 EUT – RF PCB Assembly Bottom View.................................................................................................33 14.17 EUT – Display Board Assembly Top View: Vantage .............................................................................34 14.18 EUT – Display Board Assembly Bottom View: Vantage........................................................................34 15 Exhibit D – Declaration of Similarity ...........................................................................................................35 Report Number R0907271-90 Page 3 of 35 FCC Part 90 Test Report

Pacific Crest Corporation FCC ID: KEAADLV DOCUMENT REVISION HISTORY Revision Number Report Number Description of Revision Date of Revision 0 R0907271-90 Original Report 2009-08-18 Report Number R0907271-90 Page 4 of 35 FCC Part 90 Test Report

Pacific Crest Corporation FCC ID: KEAADLV 1 General Information 1.1 Product Description for Equipment Under Test (EUT) This test and measurement report has been prepared on behalf of Pacific Crest Corporation and their product, FCC ID: KEAADLV models: ADLV-1, ADLV-2, ADLS-1, ADLS-2, TDL 450L-1, TDL-450L-2 or the EUT as referred to in the rest of this report. The EUT is a transceiver designed to provide data communication using UHF radio frequencies. FCC ID: KEAADLV models: ADLV-1 and ADLV-2 were tested as the worst case configuration in this report. Refer to the Declaration of Similarity Letter Specifications 390~430 MHz Frequency Band 430~470 MHz Tx RF Output Power 4 Watts (Maximum) Channel Spacing 25 kHz; 12.5 kHz Modulation GMSK, 4LFSK 1.2 Mechanical Description The EUT measures approximately 140.0 mm (L) x 84 mm (W) x 35.0 mm (H) and weighs 621 g. * The test data gathered are from production sample, serial number: 0926003, 0926001 provided by the manufacturer. 1.3 EUT Photo ADLV-1/-2 ADLS-1/-2 TDL 450L-1/-2 Additional photos in Exhibit C Report Number R0907271-90 Page 5 of 35 FCC Part 90 Test Report

Pacific Crest Corporation FCC ID: KEAADLV 1.4 Objective This type approval report is prepared on behalf of Pacific Crest Corporation in accordance with Part 2 and Part 90 of the Federal Communication Commissions rules. The objective of the manufacturer is to determine compliance with FCC rules, spurious radiated emissions. 1.5 Related Submittal(s)/Grant(s) FCC Part 90 conducted test report provided by Pacific Crest, Report number: ADLVFCC063009 1.6 Test Methodology All tests and measurements indicated in this document were performed in accordance with the Code of Federal Regulations Title 47 Part 2, Sub-part J as well as the following individual parts: Part 90 – Private Land Mobile Radio Service Applicable Standards: TIA/EIA-603-C, ANSI 63.4-2003, American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the range of 9 kHz to 40 GHz. All radiated and conducted emissions measurement was performed at Bay Area Compliance Laboratory, Corp. The radiated testing was performed at an antenna-to-EUT distance of 3 meters. 1.7 Measurement Uncertainty All measurements involve certain levels of uncertainties, especially in the field of EMC. The factors contributing to uncertainties are spectrum analyzer, cable loss, antenna factor calibration, antenna directivity, antenna factor variation with height, antenna phase center variation, antenna factor frequency interpolation, measurement distance variation, site imperfections, mismatch (average), and system repeatability. Based on NIS 81, The Treatment of Uncertainty in EMC Measurements, the values ranging from +2.0 dB for Conducted Emissions tests and +4.0 dB for Radiated Emissions tests are the most accurate estimates pertaining to uncertainty of EMC measurements at BACL Corp. Detailed instrumentation measurement uncertainties can be found in BACL Corp. report QAP-018. Report Number R0907271-90 Page 6 of 35 FCC Part 90 Test Report

Pacific Crest Corporation FCC ID: KEAADLV 1.8 Test Facility The Test site used by BACL Corp. to collect radiated and conducted emissions measurement data is located at it’s facility in Sunnyvale, California, USA. Test site at BACL has been fully described in reports submitted to the Federal Communication Commission (FCC) and Voluntary Control Council for Interference (VCCI). The details of these reports has been found to be in compliance with the requirements of Section 2.948 of the FCC Rules on February 11 and December 10, 1997 and Article 8 of the VCCI regulations on December 25, 1997. The facility also complies with the radiated and AC line conducted test site criteria set forth in ANSI C63.4-2003. The Federal Communications Commission, Industry Canada, and Voluntary Control Council for Interference have the reports on file and are listed under FCC file 31040/SIT 1300F2, IC registration number: 3062A, and VCCI Registration No.: C-1298 and R-1234. The test site has been approved by the FCC, IC, and VCCI for public use and is listed in the FCC Public Access Link (PAL) database. Additionally, BACL is a National Institute of Standards and Technology (NIST) accredited laboratory, under the National Voluntary Laboratory Accredited Program (Lab Code 200167-0). The current scope of accreditations can be found at http://ts.nist.gov/ts/htdocs/210/214/scopes/2001670.htm Report Number R0907271-90 Page 7 of 35 FCC Part 90 Test Report

Pacific Crest Corporation FCC ID: KEAADLV 2 System Test Configuration 2.1 Justification The EUT was configured for testing according to TIA/EIA 603-C The EUT was tested in the normal (native) operating mode to represent worst-case results during the final qualification test, the test software was provided by the client. 2.2 EUT Exercise Software Software provided by the customer was used to exercise the system in a mode simulating normal operating conditions. 2.3 Equipment Modifications No modifications were made to the EUT. 2.4 EUT Internal Configuration Details Manufacturers Descriptions Models Serial Numbers Pacific Crest Corporation 390~430 MHz PCB Board ADLV-1 0926003 Pacific Crest Corporation 430~470 MHz PCB Board ADLV-2 09260031 MDLS.16263-C-EHT- Pacific Crest Corporation Display Board Assembly - HV-G-LED1G 2.5 Interface Ports and Cabling Cable Description Length (m) From To RS232 2 EUT Laptop* *Note: Laptop was used only to program the EUT. 2.6 Power Supply Information Manufacturer Description Model Serial Number XP Power AC/DC Adapter AEL40US12 - Report Number R0907271-90 Page 8 of 35 FCC Part 90 Test Report

Pacific Crest Corporation FCC ID: KEAADLV 3 Summary of Test Results FCC Rule Description of Tests Results § 2.1046 RF Output Power Compliant * § 90.205 § 2.1047 Modulation Characteristics N/A § 2.1049 Emission mask, Occupied Bandwidth Compliant * § 90.209 § 2.1051 Spurious emissions at antenna terminals Compliant * § 90.210 § 2.1053 Field strength of spurious radiation Compliant § 90.210 § 2.1055 Frequency stability vs. temperature Compliant * § 90.213 Frequency stability vs. voltage § 90.214 Transient Frequency Behavior Compliant * § 2.1091 RF Exposure Compliant Note: N/A; There is no specific requirement for digital modulation; therefore modulation characteristic is not presented. * Please refer to the conducted test report (Report number: ADLVFCC063009) Report Number R0907271-90 Page 9 of 35 FCC Part 90 Test Report

Pacific Crest Corporation FCC ID: KEAADLV 4 FCC §2.1091 – RF Exposure 4.1 Applicable Standards According to §2.1091 and §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. According to §1.1310 and §2.1091 RF exposure is calculated. Limits for General Population/Uncontrolled Exposure Frequency Electric Field Magnetic Field Power Density Averaging Time Range (MHz) Strength (V/m) Strength (A/m) (mW/cm2) (minutes) Limits for General Population/Uncontrolled Exposure 0.3-1.34 614 1.63 *(100) 30 1.34-30 824/f 2.19/f *(180/f2) 30 30-300 27.5 0.073 0.2 30 300-1500 / / f/1500 30 1500-100,000 / / 1.0 30 f = frequency in MHz * = Plane-wave equivalent power density 4.2 MPE Prediction Predication of MPE limit at a given distance S = PG/4πR² Where: S = power density P = power input to antenna G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna 390 ~ 430 MHz Band Maximum peak output power at antenna input terminal (dBm): 36.02 Maximum peak output power at antenna input terminal (mW): 4000 Prediction distance (cm): 120 Prediction frequency (MHz): 390.15 Antenna Gain, typical (dBi): 5.0 Maximum Antenna Gain (numeric): 3.16 Power density at predication frequency and distance (mW/cm2): 0.07 MPE limit for uncontrolled exposure at predication frequency (mW/cm2): 0.2601 Report Number R0907271-90 Page 10 of 35 FCC Part 90 Test Report

Pacific Crest Corporation FCC ID: KEAADLV 430 ~ 470 MHz Band Maximum peak output power at antenna input terminal (dBm): 36.1 Maximum peak output power at antenna input terminal (mW): 4073.80 Prediction distance (cm): 120 Prediction frequency (MHz): 469.85 Antenna Gain, typical (dBi): 5.0 Maximum Antenna Gain (numeric): 3.16 Power density at predication frequency and distance (mW/cm2): 0.071 MPE limit for uncontrolled exposure at predication frequency (mW/cm2): 0.3132 Result The device is compliant with the requirement MPE limit for uncontrolled exposure. The maximum power density at the distance of 120 cm is 0.0711mW/cm2 (Limit 0.3132 mW/cm2) Report Number R0907271-90 Page 11 of 35 FCC Part 90 Test Report

Pacific Crest Corporation FCC ID: KEAADLV 5 FCC §2.1046 – Conducted Output Power 5.1 Applicable Standards Per FCC §2.1046 and §90.205: maximum ERP is dependent upon the station’s antenna HAAT and required service area. 5.2 Test Procedure TIA-603-C §2.2.1 5.3 Test Results Please refer to Part 90 conducted test report provided by Pacific Crest (Report Number: ADLVFCC063009). Report Number R0907271-90 Page 12 of 35 FCC Part 90 Test Report

Pacific Crest Corporation FCC ID: KEAADLV 6 FCC §2.1047 & §90.207 - Modulation Characteristic 6.1 Applicable Standard §2.1047 & §90.207: (a) Equipment which utilizes voice modulated communication shall show the frequency response of the audio modulating circuit over a range of 100 to 5000 Hz. for equipment which is required to have a low pass filter, the frequency response of the filter, or all of the circuitry installed between the modulation limited and the modulated stage shall be supplied. (b) Equipment which employs modulation limiting, a curve showing the percentage of modulation versus the modulation input voltage shall be supplied. 6.2 Test Procedure TIA-603-C §2.2.3 6.3 Test Results N/A; There is no specific requirement for digital modulation; therefore modulation characteristic is not presented. Report Number R0907271-90 Page 13 of 35 FCC Part 90 Test Report

Pacific Crest Corporation FCC ID: KEAADLV 7 FCC §2.1049 & § 90.209 – Occupied Bandwidth and Emission Mask 7.1 Applicable Standard §2.1049, §90.210 12.5 kHz bandwidth: For any frequency removed from the center of the authorized bandwidth f0 to 5.625 kHz removed from f0, 0dB. On any frequency removed from the center of the authorized bandwidth by a displacement frequency (fd in kHz) of more than 5.626kHz but no more than 12.5kHz, at least 7.27 (fd –2.88kHz) dB. On any frequency removed from the center of the authorized bandwidth by a displacement frequency (fd in kHz) of more than 12.5kHz at least: 50+10logP or 70 dB 25 kHz bandwidth: On any frequency removed from the center of the authorized bandwidth by a displacement frequency (fd in kHz) of more than 5kHz but not more than 10kHz, at least 83 Log (fd /5) dB. On any frequency removed from the center of the authorized bandwidth by a displacement frequency (fd in kHz) of more than 10kHz but not more than 250% of the authorized bandwidth, at least 29 Log (fd2 /11) dB or 50 dB. On any frequency removed from the center of the authorized bandwidth by more than 250% of the authorized bandwidth: least 43+ 10 Log (P). 7.2 Test Procedure The RF output of the transmitter was connected to the input of the spectrum analyzer through sufficient attenuation. The resolution bandwidth of the spectrum analyzer was set at 100 Hz and the spectrum was recorded in the frequency band ±50 KHz or + 25 kHz from the carrier frequency. 7.3 Test Results Please refer to Part 90 conducted test report provided by Pacific Crest (Report Number: ADLVFCC063009). Report Number R0907271-90 Page 14 of 35 FCC Part 90 Test Report

Pacific Crest Corporation FCC ID: KEAADLV 8 FCC §2.1051 & §90.210 – Spurious Emissions at Antenna Terminals 8.1 Applicable Standard §2.1051 and §90.210. On any frequency removed from the center of the authorized bandwidth by a displacement frequency (fd in kHz) of more than 12.5kHz at least: 50+10logP or 70 dB On any frequency removed from the center of the assigned channel by more than 250 percent at least: 43+10log (P) 8.2 Test Procedure TIA-603-C §2.2.13 8.3 Test Results Please refer to Part 90 conducted test report provided by Pacific Crest (Report Number: ADLVFCC063009). Report Number R0907271-90 Page 15 of 35 FCC Part 90 Test Report

Pacific Crest Corporation FCC ID: KEAADLV 9 FCC §2.1053 & §90.210 - Radiated Spurious Emissions 9.1 Applicable Standard §2.1053 and §90.210 9.2 Test Procedure TIA-603-C §2.2.12 The transmitter was placed on a wooden turntable, and it was transmitting into a non-radiating load which was also placed on the turntable. The measurement antenna was placed at a distance of 3 meters from the EUT. During the tests, the antenna height and polarization as well as EUT azimuth were varied in order to identify the maximum level of emissions from the EUT. The test was performed by placing the EUT on 3-orthogonal axis. The frequency range up to tenth harmonic of the fundamental frequency was investigated. Remove the EUT and replace it with substitution antenna. A signal generator was connected to the substitution antenna by a non-radiating cable. The absolute levels of the spurious emissions were measured by the substitution. Spurious emissions in dB = 10 log (TX power in Watts/0.001) – the absolute level Spurious attenuation limit in dB = 43 + 10 Log10 (power out in Watts) for EUT with a 25 KHz channel bandwidth. Spurious attenuation limit in dB = 50 + 10 Log10 (power out in Watts) for EUT with a 12.5 KHz channel bandwidth. 9.3 Test Equipment List and Details Serial Calibration Manufacturer Description Model Number Date Agilent Spectrum Analyzer E4440A US44303352 2009-05-31 Sunol Sciences Antenna JB1 A103105-3 2009-03-25 A.R.A Horn Antenna DRG-118/A 1132 2009-07-28 A. H. Systems Antenna, Horn, DRG SAS-200/571 261 2009-07-01 Ducommun Pre-Amplifier ALN-09173030-01 988251-03R 2009-03-04 Daniels Electronic 50ohm Terminator 50-T-MN 1681 - HP Pre-Amplifier 8447D 2944A06639 2009-03-06 * Statement of Traceability: BACL attests that all calibrations have been performed per the NVLAP requirements, traceable to NIST. Report Number R0907271-90 Page 16 of 35 FCC Part 90 Test Report

Pacific Crest Corporation FCC ID: KEAADLV 9.4 Test Setup Antenna port terminated with 50 ohm load EUT AC Power 9.5 Test Environmental Conditions Temperature: 15~25 °C Relative Humidity: 20~32 % ATM Pressure: 100.9~101.1kPa * The testing was performed by Dennis Huang on 2009-7-31 to 2009-8-5. Report Number R0907271-90 Page 17 of 35 FCC Part 90 Test Report

Pacific Crest Corporation FCC ID: KEAADLV 9.6 Summary of Test Results 390~ 430 MHz Band -27.27 dB at 819.7 MHz in the Vertical polarization 430~ 470 MHz Band -20.66 dB at 1349.55 MHz in the Horizontal polarization Please refer to the following tables for detailed results. 9.7 Test Result Test Mode: Transmitting mode Note: Transmitter standby mode is not applicable to this device 390~ 430 MHz Band Middle Channel (Channel spacing 12.5 kHz) Indicated Test Antenna Substituted Azimuth Limit Margin S.A. Ant. Cable Absolute Frequency (degrees) Height Polar Frequency Level (dBm) (dB) Amp. Cord. Loss Level (MHz) (m) (H/V) (MHz) (dBm) (dBuV) (dBi) (dB) (dBm) 819.7 48.86 137 1.00 H 819.7 -47.27 0 0.67 -47.94 -20 -27.94 819.7 42.41 335 1.14 V 819.7 -47.60 0 0.67 -48.27 -20 -27.27 Middle Channel (Channel spacing 25 kHz) Indicated Test Antenna Substituted Azimuth Limit Margin S.A. Ant. Cable Absolute Frequency (degrees) Height Polar Frequency Level (dBm) (dB) Amp. Cord. Loss Level (MHz) (m) (H/V) (MHz) (dBm) (dBuV) (dBi) (dB) (dBm) - - - - - - - - - - -13 - - - - - - - - - - - -13 - Note: All emission levels are very low and more than 20 dB margin, thus data are not recorded. Report Number R0907271-90 Page 18 of 35 FCC Part 90 Test Report

Pacific Crest Corporation FCC ID: KEAADLV 430~ 470 MHz Band Middle Channel (Channel spacing 12.5 kHz) Indicated Test Antenna Substituted Azimuth Limit Margin S.A. Ant. Cable Absolute Frequency (degrees) Height Polar Frequency Level (dBm) (dB) Amp. Cord. Loss Level (MHz) (m) (H/V) (MHz) (dBm) (dBuV) (dBi) (dB) (dBm) 1349.55 66.10 21 1.37 H 1349.55 -47.10 7.4 0.96 -40.66 -20 -20.66 2249.25 63.52 168 1.30 V 2249.25 -44.49 8.9 6.21 -41.80 -20 -21.80 2249.25 62.69 298 1.00 H 2249.25 -46.86 8.9 6.21 -44.17 -20 -24.17 3148.95 57.97 289 1.00 H 3148.95 -46.27 9.5 7.59 -44.36 -20 -24.36 Middle Channel (Channel spacing 25 kHz) Indicated Test Antenna Substituted Azimuth Limit Margin S.A. Ant. Cable Absolute Frequency (degrees) Height Polar Frequency Level (dBm) (dB) Amp. Cord. Loss Level (MHz) (m) (H/V) (MHz) (dBm) (dBuV) (dBi) (dB) (dBm) - - - - - - - - - - -13 - - - - - - - - - - - -13 - Report Number R0907271-90 Page 19 of 35 FCC Part 90 Test Report

Pacific Crest Corporation FCC ID: KEAADLV 10 FCC §2.1055 & §90.213- Frequency Stability 10.1 Applicable Standard §2.1055 and §90.213. 10.2 Test Procedure Frequency Stability vs. Temperature: The equipment under test was connected to an external DC power supply and the RF output was connected to a frequency counter via feed-through attenuators. The EUT was placed inside the temperature chamber. The DC leads and RF output cable exited the chamber through an opening made for the purpose. After the temperature stabilized for approximately 20 minutes, the frequency output was recorded from the counter. Frequency Stability vs. Voltage: An external variable DC power supply was connected to the equipment under test. The voltage was set to 110% of the nominal value and was then decreased until the transmitter light no longer illuminated; i.e., the end point. The output frequency was recorded for each voltage. 10.3 Test Results Please refer to Part 90 conducted test report provided by Pacific Crest (Report Number: ADLVFCC063009). Report Number R0907271-90 Page 20 of 35 FCC Part 90 Test Report

Pacific Crest Corporation FCC ID: KEAADLV 11 FCC §90.214 – Transient Frequency Behavior 11.1 Standard Applicable §90.214, Transmitters designed to operate in the 150–174 MHz and 421–512 MHz frequency bands must maintain transient frequencies within the maximum frequency difference limits. 11.2 Test Method TIA/EIA-603-C §2.2.19 11.3 Test Result Please refer to Part 90 conducted test report provided by Pacific Crest (Report Number: ADLVFCC063009). Report Number R0907271-90 Page 21 of 35 FCC Part 90 Test Report


Document Created: 2009-08-21 15:14:32
Document Modified: 2009-08-21 15:14:32
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC