TEST REPORT

FCC ID: KE3IF100A

Test Report

Download: PDF
FCCID_4338296

S FCC TEST REPORT T Report No: STS1905273W01 S Issued for Radio Systems Corp 10427 PetSafe Way Knoxville, Tennessee 37932 United States L Product Name: Wireless Pet Containment Transmitter Brand Name: PetSafe, Premier Pet A Model Name: RFA-584 Series Model: RFA-443, IF-100 FCC ID: KE3IF100A B Test Standard: FCC Part 15 Subpart C Any reproduction of this document must be done in full. No single part of this document may be reproduced without permission from STS, All Test Data Presented in this report is only applicable to presented Test sample. Shenzhen STS Test Services Co., Ltd. 1/F., Building B, Zhuoke Science Park, No.190, Chongqing Road, Fuyong Street, Bao’an District, Shenzhen, Guangdong, China TEL: +86-755 3688 6288 FAX: +86-755 3688 6277 E-mail:sts@stsapp.com

Page 2 of 20 Report No.: STS1905273W01 TEST RESULT CERTIFICATION Applicant’s Name ................... : Radio Systems Corp Address .................................. : 10427 PetSafe Way Knoxville, Tennessee 37932 United States Manufacture's Name .............. : Radio Systems Corp Address .................................. : 10427 PetSafe Way Knoxville, Tennessee 37932 United States Product Description Product Name ........................ : Wireless Pet Containment Transmitter Brand Name ........................... : PetSafe, Premier Pet Model Name ........................... : RFA-584 SeriesModel ........................... : RFA-443, IF-100 Test Standards ...................... : FCC Part 15 Subpart C Test Procedure ....................... : ANSI C63.10-2013 This device described above has been tested by STS, the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of STS, this document only be altered or revised by STS, personal only, and shall be noted in the revision of the document. Date of performance of tests…....: 30 May 2019 ~25 June 2019 Date of Issue ………………….…: 25 June 2019 Test Result………………………...: Pass Testing Engineer : (ChrisChen) Technical Manager : (Sunday Hu) Authorized Signatory : (Vita Li)

Page 3 of 20 Report No.: STS1905273W01 Table of Contents Page 1. SUMMARY OF TEST RESULTS 5 1.1 TEST FACTORY 5 1.2 MEASUREMENT UNCERTAINTY 5 2. GENERAL INFORMATION 6 2.1 GENERAL DESCRIPTION OF THE EUT 6 2.2 DESCRIPTION OF THE TEST MODES 7 2.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 8 2.4 DESCRIPTION OF NECESSARY ACCESSORIES AND SUPPORT UNITS 8 2.5 EQUIPMENTS LIST FOR ALL TEST ITEMS 9 3.CONDUCTED EMISSION TEST RESULT(SECTION 15.207) 10 3.1 POWER LINE CONDUCTED EMISSION LIMITS 10 3.2 TEST PROCEDURE 11 3.3 TEST SETUP 11 3.4 EUT OPERATING CONDITIONS 11 3.5 TEST RESULTS 12 4. RADIATED&FIELD EMISSION TEST RESULT(SECTIOU 15.209) 14 4.1 LIMIT 14 4.2 TEST PROCEDURE 14 4.3 TEST SETUP 15 4.4 TEST RESULTS 16 5.20 DB BANDWIDTH TEST 19 5.1 LIMIT 19 5.2 TEST SETUP 19 5.3 TEST RESULTS 19 APPENDIX-PHOTOS OF TEST SETUP 20

Page 4 of 20 Report No.: STS1905273W01 Revision History Rev. Issue Date Report NO. Effect Page Contents 00 25 June 2019 STS1905273W01 ALL Initial Issue

Page 5 of 20 Report No.: STS1905273W01 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: FCC Part15 , Subpart C Standard Test Item Judgment Remark Section 15.207 Conducted Emission PASS 15.209（a） Radiated emission, Spurious Emission PASS 2.1049 20 dB Bandwidth PASS 1.1 TEST FACTORY Shenzhen STS Test Services Co., Ltd. Add. : 1/F., Building B, Zhuoke Science Park, No.190, Chongqing Road, Fuyong Street, Bao’an District, Shenzhen, Guangdong,China FCC test Firm Registration Number: 625569 A2LA Certificate No.: 4338.01 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ±U,where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2,providing a level of confidence of approximately 95 %. No. Item Uncertainly 1 RF output power,conducted ±0.71dB 2 Unwanted Emissions,conducted ±0.63dB 3 All emissions,radiated 30-200MHz ±3.43dB 4 All emissions,radiated 200MHz-1GHz ±3.57dB 5 All emissions,radiated>1G ±4.13dB 6 Conducted Emission(9KHz-150KHz) ±3.18dB 7 Conducted Emission(150KHz-30MHz) ±2.70dB

Page 6 of 20 Report No.: STS1905273W01 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF THE EUT Product Name Wireless Pet Containment Transmitter Trade Name PetSafe, Premier Pet Model Name RFA-584 Series Model RFA-443, IF-100 Model Difference Only different in model name and brand name. Channel List Please refer to the Note 2. Equipemnt Category Non-ISM frequency Operating frequency 18.72KHz Modulation Type Phase Input:100-240V,50/60Hz 0.8A Max Adapter: Output:19V,1.26A Hardware version number 001 Software version number 001 Connecting I/O Port(s) Please refer to the User’s Manual Note: 1. For a more detailed features description, please refer to the manufacturer’s specifications or the User’s Manual. 2. Channel List Frequency Frequency Frequency Channel Channel Channel (KHz) (KHz) (KHz) 00 18.72 3. Table for Filed Antenna Ant. Brand Model Name Antenna Type Connector NOTE 203mm PetSafe, 1 RFA-584 diameter air N/A Antenna Premier Pet coil

Page 7 of 20 Report No.: STS1905273W01 2.2 DESCRIPTION OF THE TEST MODES To investigate the maximum EMI emission characteristics generates from EUT, the test system was pre-scanning tested base on the consideration of following EUT operation mode or test configuration mode which possible have effect on EMI emission level. Each of these EUT operation mode(s) or test configuration mode(s) mentioned above was evaluated respectively. Pretest Mode Description Mode 1 Charging+TX Mode For Conducted Emission Final Test Mode Description Mode 1 Charging+TX Mode For Radiated Emission Final Test Mode Description Mode 1 Charging+TX Mode

Page 8 of 20 Report No.: STS1905273W01 2.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED During testing channel & power controlling software provided by the customer was used to control the operating channel as well as the output power level. The RF output power selection is for the setting of RF output power expected by the customer and is going to be fixed on the firmware of the final end product power parameters Radiated Emission Test C-1 AC Plug E-1 E-2 EUT Adapter Conducted Emission Test AC Plug E-2 C-1 E-1 Adapter EUT 2.4 DESCRIPTION OF NECESSARY ACCESSORIES AND SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. Necessary accessories Item Equipment Mfr/Brand Model/Type No. Serial No. Note E-2 Adapter N/A NF19V-1.26C-DC N/A N/A C-1 DC Cable N/A N/A N/A N/A Support units Model/Type Item Equipment Mfr/Brand Serial No. Note No. N/A N/A N/A N/A N/A N/A Note: (1) FCC DOC approved. (2) FTP is Foiled Twisted Pair.

Page 9 of 20 Report No.: STS1905273W01 2.5 EQUIPMENTS LIST FOR ALL TEST ITEMS Radiation Test equipment Last Calibrated Kind of Equipment Manufacturer Type No. Serial No. calibration until Test Receiver R&S ESCI 101427 2018.10.13 2019.10.12 Signal Analyzer Agilent N9020A MY51110105 2019.03.02 2020.03.01 Active loop ZHINAN ZN30900C 16035 2018.03.11 2021.03.10 Antenna Bilog Antenna TESEQ CBL6111D 34678 2017.11.02 2020.11.1 Pre-Amplifier EM EM330 060665 2018.10.13 2019.10.12 (0.1M-3GHz) Temperature & HH660 Mieo N/A 2018.10.11 2019.10.10 Humidity Test SW BULUN BL410-E/18.905 Conduction Test equipment Last Calibrated Kind of Equipment Manufacturer Type No. Serial No. calibration until Test Receiver R&S ESCI 101427 2018.10.13 2019.10.12 LISN R&S ENV216 101242 2018.10.11 2019.10.10 LISN EMCO 3810/2NM 23625 2018.10.11 2019.10.10 Temperature & HH660 Mieo N/A 2018.10.11 2019.10.10 Humidity Test SW FARAD EZ-EMC(Ver.STSLAB-03A1 CE)

Page 10 of 20 Report No.: STS1905273W01 3.CONDUCTED EMISSION TEST RESULT(SECTION 15.207) 3.1 POWER LINE CONDUCTED EMISSION LIMITS Operating frequency band. In case the emission fall within the restricted band specified on Part 15.207 limit in the table below has to be followed. Class B (dBuV) FREQUENCY (MHz) Quasi-peak Average 0.15 -0.5 66 - 56 * 56 - 46 * 0.50 -5.0 56.00 46.00 5.0 -30.0 60.00 50.00 Note: (1) The tighter limit applies at the band edges. (2) The limit of " * " marked band means the limitation decreases linearly with the logarithm of the frequency in the range. The following table is the setting of the receiver Receiver Parameters Setting Attenuation 10 dB Start Frequency 0.15 MHz Stop Frequency 30 MHz IF Bandwidth 9 kHz

Page 11 of 20 Report No.: STS1905273W01 3.2 TEST PROCEDURE a. The EUT was placed 0.8 meters from the horizontal ground plane with EUT being connected to the power mains through a line impedance stabilization network (LISN). All other support equipments powered from additional LISN(s). The LISN provide 50 Ohm/ 50uH of coupling impedance for the measuring instrument. b. Interconnecting cables that hang closer than 40 cm to the ground plane shall be folded back and forth in the center forming a bundle 30 to 40 cm long. c. I/O cables that are not connected to a peripheral shall be bundled in the center. The end of the cable may be terminated, if required, using the correct terminating impedance. The overall length shall not exceed 1 m. d. LISN at least 80 cm from nearest part of EUT chassis. e. For the actual test configuration, please refer to the related Item –EUT Test Photos. 3.3 TEST SETUP Vertical Reference Ground Plane Test Receiver EUT 40cm 80cm LISN Horizontal Reference Ground Plane Note: 1.Support units were connected to second LISN. 2.Both of LISNs (AMN) are 80 cm from EUT and at least 80 cm from other units and other metal planes support. units. 3.4 EUT OPERATING CONDITIONS The EUT was configured for testing in a typical fashion (as a customer would normally use it). The EUT has been programmed to continuously transmit during test. This operating condition was tested and used to collect the included data.

Page 12 of 20 Report No.: STS1905273W01 3.5 TEST RESULTS Relative Temperature: 25.4℃ 65% Humidity: Test Voltage: AC 120V/60Hz Phase: L Test Mode: Mode 1 Frequency Reading Factor Result Limit Margin No. Detector (MHz) (dBuV) (dB) (dBuV) (dBuV/m) (dB) 1 0.3620 29.67 20.58 50.25 58.68 -8.43 QP 2 0.3620 24.68 20.58 45.26 48.68 -3.42 AVG 3 0.9700 15.79 20.17 35.96 56.00 -20.04 QP 4 0.9700 7.63 20.17 27.80 46.00 -18.20 AVG 5 1.4820 16.15 20.11 36.26 56.00 -19.74 QP 6 1.4820 7.35 20.11 27.46 46.00 -18.54 AVG 7 2.2020 15.68 20.04 35.72 56.00 -20.28 QP 8 2.2020 5.88 20.04 25.92 46.00 -20.08 AVG 9 4.2220 14.34 19.95 34.29 56.00 -21.71 QP 10 4.2220 4.11 19.95 24.06 46.00 -21.94 AVG 11 7.6340 13.00 19.95 32.95 60.00 -27.05 QP 12 7.6340 1.42 19.95 21.37 50.00 -28.63 AVG Remark: 1. All readings are Quasi-Peak and Average values. 2. Margin = Result (Result =Reading + Factor )–Limit

Page 13 of 20 Report No.: STS1905273W01 Relative Temperature: 25.4℃ 65% Humidity: Test Voltage: AC 120V/60Hz Phase: N Test Mode: Mode 1 Frequency Reading Factor Result Limit Margin No. Detector (MHz) (dBuV) (dB) (dBuV) (dBuV/m) (dB) 1 0.3620 29.38 20.58 49.96 58.68 -8.72 QP 2 0.3620 19.25 20.58 39.83 48.68 -8.85 AVG 3 0.7460 14.53 20.24 34.77 56.00 -21.23 QP 4 0.7460 4.67 20.24 24.91 46.00 -21.09 AVG 5 1.6700 13.22 20.10 33.32 56.00 -22.68 QP 6 1.6700 3.81 20.10 23.91 46.00 -22.09 AVG 7 3.7140 13.07 19.95 33.02 56.00 -22.98 QP 8 3.7140 1.90 19.95 21.85 46.00 -24.15 AVG 9 7.9780 10.06 19.97 30.03 60.00 -29.97 QP 10 7.9780 -1.07 19.97 18.90 50.00 -31.10 AVG 11 29.2420 8.01 19.38 27.39 60.00 -32.61 QP 12 29.2420 -3.14 19.38 16.24 50.00 -33.76 AVG Remark: 1. All readings are Quasi-Peak and Average values. 2. Margin = Result (Result =Reading + Factor )–Limit

Page 14 of 20 Report No.: STS1905273W01 4. RADIATED&FIELD EMISSION TEST RESULT(SECTIOU 15.209) 4.1 Limit Frequency Field Strength Measurement Distance [MHz] [uV/m] [Meters] 0.009 ~ 0.490 2400/F (kHz) 300 0.490 ~ 1.705 24000/F (kHz) 30 1.705 ~ 30 30 30 30 ~ 88 100 3 88 ~ 216 150 3 216 ~ 960 200 3 Above 960 500 3 Note: (1) The limit for radiated test was performed according to FCC PART 15C. (2) The tighter limit applies at the band edges. (3) Emission level (dBuV/m)=20log Emission level (uV/m). Receiver Parameter Setting Attenuation Auto Start ~ Stop Frequency 9kHz~90kHz / RB 200Hz forAV Start ~ Stop Frequency 90kHz~110kHz / RB 200Hz for QP Start ~ Stop Frequency 110kHz~490kHz / RB 200Hz/9kHz for AV Start ~ Stop Frequency 490kHz~30MHz / RB 9kHz for QP Start ~ Stop Frequency 30MHz~1000MHz / RB 120kHz for QP §15.209(d)The emission limits shown in the above table are based on measurements employing a CISPR quasi-peak detector except for the frequency bands 9-90 kHz, 110-490 kHz and above 1000 MHz. Radiated emission limits in these three bands are based on measurements employing an average detector. 4.2 TEST PROCEDURE a. The measuring distance of at 3 m shall be used for measurements at frequency 0.009MHz up to 1GHz. b. The EUT was placed on the top of a rotating table 0.8 meter above the ground at a 3 meter anechoic chamber. The table was rotated 360 degrees to determine the position of the highest radiation. c. The initial step in collecting conducted emission data is a spectrum analyzer peak detector mode pre-scanning the measurement frequency range. Significant peaks are then marked and then Quasi Peak detector mode re-measured. d. If the Peak Mode measured value compliance with and lower than Quasi Peak Mode Limit, the EUT shall be deemed to meet QP Limits and then no additional QP Mode measurement performed. e. For the actual test configuration, please refer to the related Item –EUT Test Photos. Note: Both horizontal and vertical antenna polarities were testedand performed pretest to three orthogonal axis. The worst case emissions were reported.

Page 15 of 20 Report No.: STS1905273W01 4.3 TEST SETUP （A）Radiated Emission Test-Up Frequency Below 30MHz （B）Radiated Emission Test-Up Frequency 30MHz~1GHz

Page 16 of 20 Report No.: STS1905273W01 4.4 TEST RESULTS Temperature： 22.7℃ Relative Humidity： 61% Test Voltage ： AC 120V/60Hz Test Mode ： TX Mode 4.4.1 Spurious Radiated Emission Below 30 MHz Ant. Frequency Reading Detector Cable Emission Limits Margin Factor Level (KHz) (dBμV) (PK/QP/AV) (dB/m) Loss (dBμV/m) (dB) (dBμV/m) 18.72 96.7 PK 26.27 0.1 123.07 142.16 -19.09 18.72 80.35 AV 26.27 0.1 106.72 122.16 -15.44 36 70.31 PK 22.03 0.1 92.44 136.48 -44.04 36 55.41 AV 22.03 0.1 77.54 116.48 -38.94 110 77.68 PK 10.04 0.1 87.82 126.78 -38.96 110 62.37 AV 10.04 0.1 72.51 106.78 -34.27 205 75.06 PK 9.43 0.1 84.59 121.37 -36.78 205 59.47 AV 9.43 0.1 69.00 101.37 -32.37 495 64.54 QP 1.15 0.1 65.79 73.71 -7.92 21735 69.23 QP -17.9 0.9 52.23 69.54 -17.31 1. “*” Means Fundamental frequency 2. Emission Level [dBμV/m] = Reading [dBμV] + Ant. Factor [dB/m] + Cable Loss [dB] 3.Margin [dB] = Emission Level [dBμV/m] – Limit [dBμV/m] 4.Limit calculation: Limit at specified distance + 40log (300/3) = Limit + 80 dB for up to 0.49 MHz Limit at specified distance + 40log (30/3) = Limit + 40 dB for above 0.49 MHz, Below 30 MHz 5.During the radiated emission test, the measurement antenna was aligned along the site axis and orthogonal to the axis, only the worst-case data recorded.

Page 17 of 20 Report No.: STS1905273W01 4.4.2 Spurious Radiated Emission below 1 GHz Temperature： 23.4℃ Relative Humidity： 58% Test Voltage ： AC 120V/60Hz Test Mode ： Mode 1 The following table shows the highest levels of radiated emissions on polarizations of vertical Frequency Reading Correct Result Limit Margin Remark (MHz) (dBuV) Factor(dB/m) (dBuV/m) (dBuV/m) (dB) 45.8551 44.07 -19.34 24.73 40.00 -15.27 QP 71.8320 54.93 -23.84 31.09 40.00 -8.91 QP 141.8262 52.67 -17.59 35.08 43.50 -8.42 QP 374.6225 48.98 -12.77 36.21 46.00 -9.79 QP 468.8761 47.59 -10.16 37.43 46.00 -8.57 QP 912.8620 33.69 -1.82 31.87 46.00 -14.13 QP Remark: 1. Margin = Result (Result =Reading + Factor )–Limit

Page 18 of 20 Report No.: STS1905273W01 Temperature： 23.4℃ Relative Humidity： 58% Test Voltage ： AC 120V/60Hz Test Mode ： Mode 1 The following table shows the highest levels of radiated emissions on polarizations of horizontal Frequency Reading Correct Result Limit Margin Remark (MHz) (dBuV) Factor(dB/m) (dBuV/m) (dBuV/m) (dB) 43.0504 41.95 -17.90 24.05 40.00 -15.95 QP 59.8588 50.49 -24.30 26.19 40.00 -13.81 QP 178.1322 48.82 -19.42 29.40 43.50 -14.10 QP 368.1116 43.18 -12.94 30.24 46.00 -15.76 QP 552.8831 37.62 -6.71 30.91 46.00 -15.09 QP 906.4823 33.92 -2.05 31.87 46.00 -14.13 QP Remark: 1. Margin = Result (Result =Reading + Factor )–Limit

Page 19 of 20 Report No.: STS1905273W01 5.20 DB BANDWIDTH TEST 5.1 Limit FCC Part 2.1049, Only applicable to report. 5.2 TEST SETUP Spectrum Parameter Setting Span Frequency approximately 2 to 3 times the 20 dB bandwidth RB greater than 1 % of the 20 dB bandwidth, VB equal to the RBW Detector Peak Trace Max Hold Sweep Time Auto The test program and configuration,Refer to 4.2 and 4.3 5.3 TEST RESULTS OperatingFrequency（kHz） 20 dB Bandwhidth(Hz) 18.72 281 CH00

Page 20 of 20 Report No.: STS1905273W01 APPENDIX-PHOTOS OF TEST SETUP Note:See test photos in setup photo document for the actual connections between Product and support equipment. ※※※※※END OF THE REPORT※※※※※


Document Created: 2019-06-28 19:08:13
Document Modified: 2019-06-28 19:08:13
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC