test report

FCC ID: KE3-PIF150-1

Test Report

Download: PDF
FCCID_4459312

TEST REPORT Reference No. .................... : WTS19S08058310W FCC ID ................................ : KE3-PIF150-1 Applicant ............................ : Radio Systems Corp Address .............................. : 10427 PetSafe Way, Knoxville, Tennessee 37932, United States Manufacturer .................... : Radio Systems Corp Address .............................. : 10427 PetSafe Way, Knoxville, Tennessee 37932, United States Product............................... : PIF-150 Model(s) ............................. : RFA-554A Standards........................... : FCC CFR47 Part 15.209:2019 Date of Receipt sample .... : 2019-08-22 Date of Test ....................... : 2019-08-23 to 2019-09-16 Date of Issue ...................... : 2019-09-17 Test Result ......................... : Pass Remarks: The results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver. Prepared By: Waltek Services (Shenzhen) Co., Ltd. Address: 1/F., Fukangtai Building, West Baima Road, Songgang Street, Baoan District, Shenzhen, Guangdong, China Test Site/Test Location: Waltek Services (Shenzhen) Co., Ltd. Address: 1/F., Fukangtai Building, West Baima Road, Songgang Street, Baoan District, Shenzhen, Guangdong, China Tel :+86-755-83551033 Fax:+86-755-83552400 Compiled by: Approved by: Robin Zhou / Test Engineer Philo Zhong / Manager Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn Page 1 of 28

Reference No.: WTS19S08058310W Page 2 of 28 1 Laboratories Introduction Waltek Services (Shenzhen) Co., Ltd is a professional third-party testing and certification laboratory with multi-year product testing and certification experience, established strictly in accordance with ISO/IEC 17025 requirements, and accredited by ILAC (International Laboratory Accreditation Cooperation) member. A2LA (American Association for Laboratory Accreditation, the certification number is 4243.01) of USA, CNAS (China National Accreditation Service for Conformity Assessment, the registration number is L3110) of China.Meanwhile, Waltek has got recognition as registration and accreditation laboratory from EMSD (Electrical and Mechanical Services Department), and American Energy star, FCC(The Federal Communications Commission), CEC(California energy efficiency), ISED (Innovation, Science and Economic Development Canada). It’s the strategic partner and data recognition laboratory of international authoritative organizations, such as Intertek(ETL-SEMKO), TÜV Rheinland, TÜV SÜD, etc. Waltek Services (Shenzhen) Co., Ltd is one of the largest and the most comprehensive third party testing laboratory in China. Our test capability covered four large fields: safety test. ElectroMagnetic Compatibility(EMC), and energy performance, wireless radio. As a professional, comprehensive, justice international test organization, we still keep the scientific and rigorous work attitude to help each client satisfy the international standards and assist their product enter into globe market smoothly. Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTS19S08058310W Page 3 of 28 1.1 Test Facility A. Accreditations for Conformity Assessment (International) Country/Region Scope Covered By Scope Note USA FCC ID \ SDoC 1 Canada IC ID \ VOC 2 Japan MIC-T \ MIC-R - Europe EMCD \ RED - Taiwan NCC - ISO/IEC 17025 Hong Kong OFCA - Australia RCM - India WPC - Thailand NTC - Singapore IDA - Note: 1. FCC Designation No.: CN1201. Test Firm Registration No.: 523476. 2. ISED CAB identifier: CN0013. Test Firm Registration No.: 7760A. B.TCBs and Notify Bodies Recognized Testing Laboratory. Recognized Testing Laboratory of … Notify body number TUV Rheinland Intertek Optional. TUV SUD SGS Phoenix Testlab GmbH 0700 Element Materials Technology Warwick Ltd. 0891 Timco Engineering, Inc. 1177 Eurofins Product Service GmbH 0681 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTS19S08058310W Page 4 of 28 2 Contents Page COVER PAGE………………………………………………………………………………………………………1 1 LABORATORIES INTRODUCTION ......................................................................................................... 2 1.1 TEST FACILITY ................................................................................................................................ 3 2 CONTENTS ............................................................................................................................................... 4 3 REVISION HISTORY................................................................................................................................. 5 4 GENERAL INFORMATION ....................................................................................................................... 6 4.1 GENERAL DESCRIPTION OF E.U.T. .................................................................................................. 6 4.2 DETAILS OF E.U.T. ......................................................................................................................... 6 4.3 TEST MODE .................................................................................................................................... 6 5 EQUIPMENT USED DURING TEST ......................................................................................................... 7 5.1 EQUIPMENT LIST ............................................................................................................................. 7 5.2 MEASUREMENT UNCERTAINTY ......................................................................................................... 7 5.3 TEST EQUIPMENT CALIBRATION ....................................................................................................... 7 6 TEST SUMMARY ...................................................................................................................................... 8 7 CONDUCTED EMISSION ......................................................................................................................... 9 7.1 E.U.T. OPERATION ......................................................................................................................... 9 7.2 EUT SETUP .................................................................................................................................... 9 7.3 MEASUREMENT DESCRIPTION .......................................................................................................... 9 7.4 CONDUCTED EMISSION TEST RESULT ............................................................................................ 10 8 RADIATED SPURIOUS EMISSIONS ..................................................................................................... 12 8.1 EUT OPERATION .......................................................................................................................... 12 8.2 TEST SETUP ................................................................................................................................. 13 8.3 SPECTRUM ANALYZER SETUP ........................................................................................................ 14 8.4 TEST PROCEDURE ........................................................................................................................ 14 8.5 CORRECTED AMPLITUDE & MARGIN CALCULATION ......................................................................... 14 8.6 SUMMARY OF TEST RESULTS ........................................................................................................ 15 9 BANDWIDTH MEASUREMENT ............................................................................................................. 16 9.1 TEST PROCEDURE ........................................................................................................................ 16 9.2 TEST RESULT ............................................................................................................................... 16 10 ANTENNA REQUIREMENT ................................................................................................................... 17 11 PHOTOGRAPHS – MODEL RFA-554A TEST SETUP PHOTOS ......................................................... 18 11.1 PHOTOGRAPH-CONDUCTED EMISSIONS TEST SETUP PHOTOS ........................................................ 18 11.2 PHOTOGRAPH – RADIATION SPURIOUS EMISSION TEST SETUP PHOTOS .......................................... 18 12 PHOTOGRAPHS - CONSTRUCTIONAL DETAILS ............................................................................... 20 12.1 MODEL RFA-554A – EXTERNAL PHOTOS ...................................................................................... 20 12.2 MODEL RFA-554A – INTERNAL PHOTOS ........................................................................................ 25 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTS19S08058310W Page 5 of 28 3 Revision History Date of Date of Date of Test report No. Receipt Purpose Comment Approved Test Issue sample 2019-08-23 to WTS19S08058310W 2019-08-22 2019-09-17 original - Valid 2019-09-16 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTS19S08058310W Page 6 of 28 4 General Information 4.1 General Description of E.U.T. Product: PIF-150 Model(s): RFA-554A Hardware Version: 000 Software Version: 001 4.2 Details of E.U.T. Operation Frequency: 18.726kHz Type of Modulation: Phase Antenna installation: Internal Integrated Loop Antenna Antenna Gain: N/A Ratings: Input:19V 1.26A powered by AC ADAPTER ( AC ADAPTER: Model NF19V-1.26C-DC, Input 100-240V~50/60Hz, 0.8A Max ) 4.3 Test Mode All test mode(s) and condition(s) mentioned were considered and evaluated respectively by performing full tests, the worst data were recorded and reported. Test mode Test channel Transmitting 18.726kHz Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTS19S08058310W Page 7 of 28 5 Equipment Used during Test 5.1 Equipment List Conducted Emissions Test Site Last Calibration Item Equipment Manufacturer Model No. Serial No. Calibration Due Date Date 1 EMI Test Receiver R&S ESCI 100947 2019-07-15 2020-07-14 2 LISN R&S ENV216 100115 2019-07-15 2020-07-14 3 Cable Top TYPE16(3.5M) - 2019-07-15 2020-07-14 3m Semi-anechoic Chamber for Radiation Emissions Last Calibration Item Equipment Manufacturer Model No. Serial No Calibration Due Date Date 1 Test Receiver R&S ESCI 101296 2019-04-20 2020-04-19 2 Spectrum Analyzer R&S FSL6 100959 2018-11-18 2019-11-17 Trilog Broadband 3 SCHWARZBECK VULB9160 9160-3325 2019-05-24 2020-05-23 Antenna 4 Active Loop Antenna Com-power AL-130R 10160007 2019-04-28 2020-04-27 5 Amplifier ANRITSU MH648A M43381 2019-04-19 2020-04-18 6 Cable HUBER+SUHNER CBL2 525178 2019-04-20 2020-04-19 Coaxial Cable TYPE16 7 Top - 2018-10-15 2019-10-14 (below 1GHz) (13M) 5.2 Measurement Uncertainty Parameter Uncertainty Radio Frequency ± 1 x 10-6 RF Power ± 1.0 dB Conducted Emissions test ± 3.64 dB (AC mains 150KHz~30MHz) 3.03dB (Loop antenna 9k~30MHz) Radiated Spurious Emissions test ± 5.03 dB (Bilog antenna 30M~1000MHz) Confidence interval：95%. Confidence factor:k=2 5.3 Test Equipment Calibration All the test equipments used are valid and calibrated by GUANG ZHOU GRG METROLOGY & TEST CO., LTD. address is No.163, Pingyun Rd. West of Huangpu Ave,Tianhe District, Guangzhou, Guangdong, China. Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTS19S08058310W Page 8 of 28 6 Test Summary Test Items Test Requirement Result Conduct Emission 15.207(a) Pass 15.205(a) Radiated Spurious Emissions Pass 15.209(a) 15.205(a) Bandwidth Measurement Pass 15.215(c) Antenna Requirement 15.203 Pass Note: Pass =Compliance; NC=Not Compliance; NT=Not Tested; N/A=Not Applicable. Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTS19S08058310W Page 9 of 28 7 Conducted Emission Test Requirement: FCC CFR 47 Part 15 Section 15.207 Test Method: ANSI C63.10:2013 Test Result: PASS Frequency Range: 150kHz to 30MHz Class/Severity: Class B allca Conducted Limit (dBuV) Limit: Frequency (MHz) Guasi—peak Average 0.15 to 0.5 66 to 56* 56 to 46* 0.5 to 5.0 56 46 5.0 to 30 60 50 *Decreases with the logarithm of the frequency. 7.1 E.U.T. Operation Operating Environment : Temperature: 22.06 °C Humidity: 54.2 % RH Atmospheric Pressure: 101.8kPa Test Voltage: AC 120V, 60Hz EUT Operation : The test was performed in Transmitting mode, the test data were shown in the report. 7.2 EUT Setup The conducted emission tests were performed using the setup accordance with the ANSI C63.10:2013. | Receivel—l PC —— —p —— +A ‘0.8m e L L V L 7 :500 —— 7.3 Measurement Description The maximised peak emissions from the EUT was scanned and measured for both the Live and Neutral Lines. Quasi—peak & average measurements were performed if peak emissions were within 6dB of the average limit line. Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTS19S08058310W Page 10 of 28 7.4 Conducted Emission Test Result Live line: Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

m 0 » a m ho n iss |tear| 1—|—"oiss| ber oo" |—ae—| en sn ane( es en on z—| —onss| ear |~ors—| ces sare 2e ae 5| —oneo ore—| o7 sass s|aeg on 1| —oneo isse—|~orr—| se seis seee ave s—| —onoo| sean—|~orr—| es sios m on s —oreo tess |~orr—| se se n awe 7—| —ossiol sean—|~an0—| is20—| seer mer| on a—| —ossol soar sn t aeer| 225| awe e —osras| seee—|~sar—| m sear |vol on m—| —asmel sror|—sar—| se wear| mss we m —asenl zow |sar—| zon seon|s 19]_or 2—| —osnl ns |—san| sns o woml w

Reference No.: WTS19S08058310W Page 12 of 28 8 Radiated Spurious Emissions Test Requirement: FCC Part15 Paragraph 15.209, 15.205(a) Test Method: ANSI C63.10:2013 Test Result: PASS Measurement Distance: 3m Limit: FCC Part15 Paragraph 15.209 Field Strength Field Strength Limit at 3m Measurement Dist Frequency Distance (MHz) uV/m uV/m dBuV/m (m) 0.009 ~ 0.490 2400/F(kHz) 300 10000 * 2400/F(kHz) 20log(2400/F(kHz)) + 80 0.490 ~ 1.705 24000/F(kHz) 30 100 * 24000/F(kHz) 20log(24000/F(kHz)) + 40 1.705 ~ 30 30 30 100 * 30 20log(30) + 40 30 ~ 88 100 3 100 20log(100) 88 ~ 216 150 3 150 20log(150) 216 ~ 960 200 3 200 20log(200) Above 960 500 3 500 20log(500) 8.1 EUT Operation Operating Environment : Temperature: 23.4 C Humidity: 54.1 % RH Atmospheric Pressure: 101.9kPa Test Voltage: AC 120V, 60Hz EUT Operation : The test was performed in Transmitting mode, the test data were shown in the report. Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTS19S08058310W Page 13 of 28 8.2 Test Setup The radiated emission tests were performed in the 3m Semi- Anechoic Chamber test site, using the setup accordance with the ANSI C63.10:2013 The test setup for emission measurement below 30MHz. Semi-anechoic 3m Chamber Turn Table From 0°to 360° 3m EUT Turn Table 0.8m PC Spectrum AMP Combining System Analyzer Network The test setup for emission measurement from 30 MHz to 1 GHz. Semi-anechoic 3m Chamber Antenna Elevation Varies From 1 to 4 m Turn Table From 0°to 360° 3m EUT 0.8m Turn Table PC Spectrum AMP Combining System Analyzer Network Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTS19S08058310W Page 14 of 28 8.3 Spectrum Analyzer Setup Below 30MHz Sweep Speed .............................................. Auto IF Bandwidth ................................................ 10kHz Video Bandwidth.......................................... 10kHz Resolution Bandwidth.................................. 10kHz 30MHz ~ 1GHz Sweep Speed .............................................. Auto Detector ..................................................... PK Resolution Bandwidth .................................. 100kHz Video Bandwidth.......................................... 300kHz 8.4 Test Procedure 1. The EUT is placed on a turntable, which is 0.8m above ground plane for below 1GHz and 1.5m for above 1GHz. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna, which is moved from 1m to 4m to find out the maximum emissions. The spectrum was investigated from the lowest radio frequency signal generated in the device, without going below 9 kHz, up to the tenth harmonic of the highest fundamental frequency or to 40 GHz, whichever is lower. 4. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 5. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 6. Repeat above procedures until the measurements for all frequencies are complete. 7. The radiation measurements are tested under 3-axes(X,Y,Z) position(X denotes lying on the table, Y denotes side stand and Z denotes vertical stand), After pre-test, It was found that the worse radiation emission was get at the Z position. So the data shown was the Z position only. 8.5 Corrected Amplitude & Margin Calculation The Corrected Amplitude is calculated by adding the Antenna Factor and Cable Factor, and subtracting the Amplifier Gain from the Amplitude reading. The basic equation is as follows: Corr. Ampl. = Indicated Reading + Antenna Factor + Cable Factor - Amplifier Gain The “Margin” column of the following data tables indicates the degree of compliance with the applicable limit. For example, a margin of -7dB means the emission is 7dB below the maximum limit for Class B. The equation for margin calculation is as follows: Margin = Corr. Ampl. – Limit Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTS19S08058310W Page 15 of 28 8.6 Summary of Test Results Test Frequency: 9 kHz ~ 30 MHz Receiver RX Antenna FCC Part 15.209 Turn table Corrected Corrected Frequency Reading Angle Factor Amplitude (AV) Height Polar Limit Margin (AV) (dBμV (dBμV (dBμV/m (kHz) Degree (m) (H/V) (dB/m) (dB) @3m) @3m) @3m) 18.726 63.56 343 1.7 H 28.00 91.56 122.16 -30.60 18.726 59.34 169 1.6 V 28.00 87.34 122.16 -34.82 415.26 32.19 99 1.6 H 20.10 52.29 95.24 -42.95 885.41 23.45 323 1.9 V 20.81 44.26 68.66 -24.40 1765.83 19.37 343 1.7 V 20.55 39.92 69.54 -29.62 Test Frequency: 30 MHz ~ 1 GHz Turn RX Antenna FCC Part 15.209 Receiver Corrected Frequency Detector table Corrected Reading Factor Angle Height Polar Amplitude Limit Margin (dBμV (dBμV/m (dBμV/m (MHz) QP Degree (m) (H/V) (dB/m) (dB) @3m) @3m) @3m) 36.90 32.64 QP 174 1.4 H -17.21 15.43 40.00 -24.57 36.90 45.08 QP 283 1.4 V -17.21 27.87 40.00 -12.13 114.11 37.10 QP 252 1.1 H -19.09 18.01 43.50 -25.49 114.11 40.80 QP 293 1.2 V -19.09 21.71 43.50 -21.79 455.91 40.67 QP 29 1.7 H -12.83 27.84 46.00 -18.16 455.91 39.98 QP 258 1.5 V -12.83 27.15 46.00 -18.85 Note: Correct factor = Cable loss + Antenna factor Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTS19S08058310W Page 16 of 28 9 Bandwidth Measurement Test Requirement: FCC Part15.215(C), Part15.205 (a) Test Method: ANSI C63.10: 2013 9.1 Test Procedure 1. The EUT is placed on a turntable, which is 0.8m above ground plane 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna, which is moved from 1m to 4m to find out the maximum emissions. 4. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 5. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 6. The radiation measurements are tested under 3-axes(X,Y,Z) position(X denotes lying on the table, Y denotes side stand and Z denotes vertical stand), After pre-test, It was found that the worse radiation emission was get at the Z position. So the data shown was the Z position only. 7. Bandwidth Measure the resolution bandwidth of 30 Hz and the video bandwidth of 100 Hz were used. 8. Measured the spectrum width with power higher than 20dB below carrier and 99% Bandwidth. 9.2 Test Result 20dB Bandwidth 99% Bandwidth Frequency(kHz) Emission(kHz) Emission(kHz) 18.726 1.365 1.365 Test Plot Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTS19S08058310W Page 17 of 28 10 Antenna Requirement An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section. The manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. This requirement does not apply to carrier current devices or to devices operated under the provisions of §15.211, §15.213, §15.217, §15.219, or §15.221. Further, this requirement does not apply to intentional radiators that must be professionally installed, such as perimeter protection systems and some field disturbance sensors, or to other intentional radiators which, in accordance with §15.31(d), must be measured at the installation site. However, the installer shall be responsible for ensuring that the proper antenna is employed so that the limits in this part are not exceeded. For intentional device, according to FCC 15 CFR Section 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. Result: The EUT has one Internal Integrated Loop Antenna, Meets the requirements of FCC 15.203. ANT Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTS19S08058310W Page 18 of 28 11 Photographs – Model RFA-554A Test Setup Photos 11.1 Photograph-Conducted Emissions Test Setup Photos 11.2 Photograph – Radiation Spurious Emission Test Setup Photos 9 kHz to 30 MHz Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTS19S08058310W Page 19 of 28 From 30 MHz to 1GHz Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTS19S08058310W Page 20 of 28 12 Photographs - Constructional Details 12.1 Model RFA-554A – External Photos Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTS19S08058310W Page 21 of 28 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTS19S08058310W Page 22 of 28 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTS19S08058310W Page 23 of 28 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTS19S08058310W Page 24 of 28 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTS19S08058310W Page 25 of 28 12.2 Model RFA-554A – Internal Photos ANT Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTS19S08058310W Page 26 of 28 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTS19S08058310W Page 27 of 28 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTS19S08058310W Page 28 of 28 ======End of Report====== Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn


Document Created: 2019-09-26 22:15:02
Document Modified: 2019-09-26 22:15:02
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC