Test Report

FCC ID: KE3-3003330

Test Report

Download: PDF
FCCID_4015123

S FCC TEST REPORT T Report No:STS1808209W02 S Issued for Radio Systems Corporation 10427 PetSafe Way. Knoxville, TN 37932 USA Product Name: Ricochet Toy L Brand Name: Model Name: PetSafe 300 3330 A Series Model: FCC ID: N/A KE3-3003330 B Test Standard: FCC Part 15.249 Any reproduction of this document must be done in full. No single part of this document may be reproduced without permission from STS, All Test Data Presented in this report is only applicable to presented Test sample. Shenzhen STS Test Services Co., Ltd. 1/F., Building B, Zhuoke Science Park, No.190, Chongqing Road, Fuyong Street, Bao’an District, Shenzhen, Guangdong, China TEL: +86-755 3688 6288 FAX: +86-755 3688 6277 E-mail:sts@stsapp.com

Page 2 of 26 Report No.: STS1808209W02 TEST RESULT CERTIFICATION Applicant’s name : Radio Systems Corporation Address : 10427 PetSafe Way. Knoxville, TN 37932 USA Manufacture's Name : Radio Systems Corporation Address : 10427 PetSafe Way. Knoxville, TN 37932 USA Product description Product Name ........................ : Ricochet Toy Brand Name ......................... : PetSafe Model Name ........................... : 300 3330 Series Model .......................... : N/A Test Standards ...................... : FCC Part15.249 Test procedure : ANSI C63.10-2013 This device described above has been tested by STS, the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of STS, this document only be altered or revised by STS, personal only, and shall be noted in the revision of the document. Date of Test : Date of performance of tests : 23 Aug.2018 ~ 28 Aug.2018 Date of Issue : 29 Aug.2018 Test Result : Pass Testing Engineer : ( Chris chen ) Technical Manager : ( Sean she ) Authorized Signatory : (Vita Li)

Page 3 of 26 Report No.: STS1808209W02 Table of Contents Page 1. SUMMARY OF TEST RESULTS 5 1.1 TEST FACTORY 6 1.2 MEASUREMENT UNCERTAINTY 6 2. GENERAL INFORMATION 7 2.1 GENERAL DESCRIPTION OF EUT 7 2.2 DESCRIPTION OF TEST MODES 8 2.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 9 2.4 DESCRIPTION OF SUPPORT UNITS 9 2.5 EQUIPMENTS LIST FOR ALL TEST ITEMS 10 3. EMC EMISSION TEST 11 3.1 CONDUCTED EMISSION MEASUREMENT 11 3.2 RADIATED EMISSION MEASUREMENT 14 4. BANDWIDTH TEST 23 4.2 TEST SETUP 23 4.3 EUT OPERATION CONDITIONS 23 4.4 TEST RESULTS 24 5. ANTENNA REQUIREMENT 25 5.1 STANDARD REQUIREMENT 25 5.2 EUT ANTENNA 25 APPENDIX- PHOTOS OF TEST SETUP 26

Page 4 of 26 Report No.: STS1808209W02 Revision History Rev. Issue Date Report NO. Effect Page Contents 00 29 Aug.2018 STS1808209W02 ALL Initial Issue

Page 5 of 26 Report No.: STS1808209W02 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: FCC Part 15.249 , Subpart C Standard Test Item Judgment Remark Section 15.207 Conducted Emission N/A -- 15.203 Antenna Requirement Pass -- 15.249 Radiated Spurious Emission Pass -- 15.205 Radiated Band Edge Emission Pass -- 15.249 Occupied Bandwidth Pass -- NOTE: (1)” N/A” denotes test is not applicable in this Test Report (2)All tests are according to ANSI C63.10-2013

Page 6 of 26 Report No.: STS1808209W02 1.1 TEST FACTORY Shenzhen STS Test Services Co., Ltd. Add. : 1/F., Building B, Zhuoke Science Park, No.190, Chongqing Road, Fuyong Street, Bao’an District, Shenzhen, Guangdong, China CNAS Registration No.: L7649; FCC Registration No.: 625569 IC Registration No.: 12108A; A2LA Certificate No.: 4338.01; 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U，where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95 %。 No. Item Uncertainty 1 Conducted Emission (9KHz-150KHz) ±2.88dB 2 Conducted Emission (150KHz-30MHz) ±2.67dB 3 RF power,conducted ±0.71dB 4 Spurious emissions,conducted ±0.63dB 5 All emissions,radiated (9KHz-30MHz) ±3.02dB 6 All emissions,radiated (30MHz-200MHz) ±3.80dB 7 All emissions,radiated (200MHz-1000MHz) ±3.97dB

Page 7 of 26 Report No.: STS1808209W02 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT Product Name Ricochet Toy Trade Name PetSafe Model Name 300 3330 Series Model N/A Model Difference N/A The EUT is Ricochet Toy Operation Frequency: 2405MHz Modulation Type: GFSK Antenna Designation: Dipole Antenna Gain(Peak): -0.1 dBi Product Description Based on the application, features, or specification exhibited in User's Manual, the EUT is considered as an ITE/Computing Device. More details of EUT technical specification, please refer to the User's Manual. Channel List Please refer to the Note 2. Power Rating Input: DC 4.5V (3 * AAA Batteries) Hardware version number CZ10V13 Software version number CZ20160722_V5_32 Note: 1. For a more detailed features description, please refer to the manufacturer’s specifications or the User’s Manual. 2 Table for Filed Antenna Ant. Brand Model Name Antenna Type Connector Gain (dBi) NOTE 1 PetSafe 300 3330 Dipole N/A -0.1 Antenna

Page 8 of 26 Report No.: STS1808209W02 2.2 DESCRIPTION OF TEST MODES For conducted test items and radiated spurious emissions Each of these EUT operation mode(s) or test configuration mode(s) mentioned below was evaluated respectively.. Pretest Mode Data/Modulation Mode 1 GFSK Note: (1) All above mode have been measurement, only worst data was reported.

Page 9 of 26 Report No.: STS1808209W02 2.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED During testing channel & power controlling software provided by the customer was used to control the operating channel as well as the output power level. The RF output power selection is for the setting of RF output power expected by the customer and is going to be fixed on the firmware of the final end product power parameters Radiated Spurious Emission Test E-1 EUT 2.4 DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. Item Equipment Mfr/Brand Model/Type No. Serial No. Note N/A N/A N/A N/A N/A N/A Item Shielded Type Ferrite Core Length Note N/A N/A N/A N/A N/A Note: (1) The support equipment was authorized by Declaration of Confirmation. (2) For detachable type I/O cable should be specified the length in cm in『Length』column.

Page 10 of 26 Report No.: STS1808209W02 2.5 EQUIPMENTS LIST FOR ALL TEST ITEMS Radiation Test equipment Kind of Equipment Manufacturer Type No. Serial No. Last calibration Calibrated until EMI Test Receiver R&S ESCI 102086 2017.10.15 2018.10.14 Bilog Antenna TESEQ CBL6111D 34678 2017.11.02 2018.11.01 BBHA 9120D Horn Antenna Schwarzbeck 9120D-1343 2017.10.27 2018.10.26 (1201) Passive Loop ZHNAN ZN3090C 16035 2018.03.11 2019.03.10 (9K--30MHz) Pre-mplifier EM EM330 60538 2018.03.11 2019.03.10 (0.1M-3GHz) PreAmplifier Agilent 8449B 60538 2017.10.15 2018.10.14 USB RF power 15I00041SNO0 DARE RPR3006W 2017.10.15 2018.10.14 sensor 3 Semi-anechoic Changling 966 N/A 2017.10.15 2018.10.14 chamber Conduction Test equipment Kind of Equipment Manufacturer Type No. Serial No. Last calibration Calibrated until Test Receiver R&S ESCI 101427 2017.10.15 2018.10.14 LISN R&S ENV216 101242 2017.10.15 2018.10.14 conduction Cable EM C01 N/A 2018.03.11 2019.03.10 Temperature & Mieo HH660 N/A 2017.10.15 2018.10.14 Humitidy

Page 11 of 26 Report No.: STS1808209W02 3. EMC EMISSION TEST 3.1 CONDUCTED EMISSION MEASUREMENT 3.1.1 POWER LINE CONDUCTED EMISSION LIMITS Operating frequency band. In case the emission fall within the restricted band specified on Part 15.249 limit in the table below has to be followed. FREQUENCY (MHz) Quasi-peak Average 0.15 -0.5 66 - 56 * 56 - 46 * 0.50 -5.0 56.00 46.00 5.0 -30.0 60.00 50.00 Note: (1) The tighter limit applies at the band edges. (2) The limit of " * " marked band means the limitation decreases linearly with the logarithm of the frequency in the range. The following table is the setting of the receiver Receiver Parameters Setting Attenuation 10 dB Start Frequency 0.15 MHz Stop Frequency 30 MHz IF Bandwidth 9 kHz

Page 12 of 26 Report No.: STS1808209W02 3.1.2 TEST PROCEDURE a. The EUT was 0.8 meters from the horizontal ground plane and 0.4 meters from the vertical ground plane with EUT being connected to the power mains through a line impedance stabilization network (LISN). All other support equipments powered from additional LISN(s). The LISN provide 50 Ohm/ 50uH of coupling impedance for the measuring instrument. b. Interconnecting cables that hang closer than 40 cm to the ground plane shall be folded back and forth in the center forming a bundle 30 to 40 cm long. c. I/O cables that are not connected to a peripheral shall be bundled in the center. The end of the cable may be terminated, if required, using the correct terminating impedance. The overall length shall not exceed 1 m. d. LISN at least 80 cm from nearest part of EUT chassis. e. For the actual test configuration, please refer to the related Item –EUT Test Photos. 3.1.3 TEST SETUP Vertical Reference Ground Plane Test Receiver EUT 40cm 80cm LISN Horizontal Reference Ground Plane Note: 1.Support units were connected to second LISN. 2.Both of LISNs (AMN) are 80 cm from EUT and at least 80 cm from other units and other metal planes support. units. 3.1.4 EUT OPERATING CONDITIONS The EUT was configured for testing in a typical fashion (as a customer would normally use it). The EUT has been programmed to continuously transmit during test. This operating condition was tested and used to collect the included data.

b mas»_I um eP ts Report No.: STS1808209W02 3.1.5 TEST RESULTS Temperature: 24°C Relative Humidity: 60% Test Voltage: AC 120V/60Hz Phase: L/N Test Mode: N/A Note: EUT is only power by battery, So it is not applicable for this test. 1/F., Building B, Zhuoke Science Park, No.190, Chongaing Road, Fuyong Street, Bao‘an District, Shenzhen, Guangdong, China Shenzhen STS Test Services CO. Ltd 4 Tel: + 86—755 3688 6208 Faxi+ 86—755 3688 6277 Hitpy//www.stsapp.com E—mail: sts@stsapp.com

Page 14 of 26 Report No.: STS1808209W02 3.2 RADIATED EMISSION MEASUREMENT 3.2.1 RADIATED EMISSION LIMITS 20dBc in any 100 kHz bandwidth outside the operating frequency band. In case the emission fall within the restricted band specified on Part 15.249 and the Part 15.209(a) limit in the table below has to be followed. Standard FCC 15.209 Frequencies Field Strength Measurement Distance (MHz) (micorvolts/meter) (meters) 0.009~0.490 2400/F(KHz) 300 0.490~1.705 24000/F(KHz) 30 1.705~30.0 30 30 30~88 100 3 88~216 150 3 216~960 200 3 960~1000 500 3 Above 1000 Other:74.0 dB(μV)/m (Peak) 3 54.0 dB(μV)/m (Average) Standard FCC 15.249 Field Strength of Field Strength of Frequency of Emission fundamental Harmonics (MHz) (millivolts /meter) (microvolts/meter) 900~928 50 500 2400~2483.5 50 500 5725~5875 50 500 24000~242500 250 2500 Notes: (1) Emissions radiated outside of the specified frequency bands, except for harmonics, shall be attenuated by at least 50 dB below the level of the fundamental or to the general radiated emission limits in Section 15.209, whichever is the lesser attenuation. Spectrum Parameter Setting Detector Peak/AV Attenuation Auto Start Frequency 1000 MHz Stop Frequency 10th carrier harmonic RB (emission in restricted band) >20BW VB (emission in restricted band) =3xRB

Page 15 of 26 Report No.: STS1808209W02 Receiver Parameter Setting Attenuation Auto 9kHz~90kHz / RB 200Hz for PK & AV 90kHz~110kHz / RB 200Hz for QP Start ~ Stop Frequency 110kHz~490kHz / RB 200Hz for PK & AV 490kHz~30MHz / RB 9kHz for QP 30MHz~1000MHz / RB 120kHz for QP 3.2.2 TEST PROCEDURE a. The measuring distance of 3m shall be used for measurements. The EUT was placed on the top of arotating table 0.8 meter above the ground at a 3 meter semi-anechoic chamber. The table was rotated 360 degrees to determine the position of the highest radiation(Below 1GHz) b. The measuring distance of 3m shall used for measurements. The EUT was placed on the top of a rotating table 1.5 meter above the ground at a 3 meter semi-anechoic chamber. The table was rotated 360 degrees to determine the position of the highest radiation(Above 1GHz) c. The height of the test antenna shall vary between 1m to 4m.Both horizontal and vertical polarization Of the antenna are set to make the measurement. d. The initial step in collecting radiated emission data is a receive peak detector mode. Pre-scanning the measurement frequency range. Significant peaks are then marked and then Quasi Peak detector mode re-measured. e. All readings are peak unless otherwise stated QP in column of Note. Peak denoted that the Peak reading compliance with the QP limits and then QP Mode measurement didn’t perform (Below 1GHz) f. All readings are Peak mode value unless otherwise stated AVG in column of Note. If the Peak mode measured value compliance with the Peak limits and lower than AVG Limits, the EUT shall be deemed to meet Peak & AVG limits and then only Peak mode was measured, but AVG mode didn’t perform.(Above 1GHz) g. For the actual test configuration, please refer to the related Item –EUT Test Photos. Note: Both horizontal and vertical antenna polarities were tested and performed pretest to three orthogonal axis. The worst case emissions were reported 3.2.3 DEVIATION FROM TEST STANDARD No deviation

ma» I mma» CroRcrirs Report No.: STS1808209W02 3.2.4 TEST SETUP (A) Radiated Emission Test—Up Frequency Below 30MHz Metal Full Soldered Ground Plane Spectrum Analyzer / Receiver (B) Radiated Emission Test—Up Frequency 30MHz~1GHz RX Antennia Ant. feed point Metal Full Soldered Ground Plane Spectrum Analyzer ; Receiver (C) Radiated Emission Test—Up Frequency Above 1GHz Metal Full Soidered Ground Plane System Simulator 1/F., Building B, Zhuoke Science Park, No.190, Chongaing Road, Fuyong Street, Bao‘an District, Shenzhen, Guangdong, China Shenzhen STS TeSt SerViCeS CO. Ltd 4 Tel: + 86—755 3688 6208 Faxi+ 86—755 3688 6277 Hitpy//www.stsapp.com E—mail: sts@stsapp.com

) I= Page 17 of 26 Report No.: STS1808209W02 3.2.5 FIELD STRENGTH CALCULATION The field strength is calculated by adding the Antenna Factor and Cable Factor and subtracting the Amplifier Gain and Duty Cycle Correction Factor (if any) from the measured reading. The basic equation with a sample calculation is as follows: FS = RA + AF + CL — AG Where FS = Field Strength CL = Cable Attenuation Factor (Cable Loss) RA = Reading Amplitude AG = Amplifier Gain AF = Antenna Factor For example Frequency FS RA AF CL AG Factor (MHz) (dBpuV/m) (dBuV/m) (dB) (dB) (dB) (dB) 300 40 58.1 12.2 1.6 31.9 —18.1 Factor=AF+CL—AG 3.2.6 EUT OPERATING CONDITIONS The EUT tested system was configured as the statements of 2.4 Unless otherwise a special operating condition is specified in the follows during the testing. Below 30 MHz Temperature: 26.4 °C Relative Humidity: 55% Test Voltage: DC 4.5V Polarization: Test Mode: —— Freq. Reading Limit Margin State (MHz) (dBuV/m) (dBuV/m) (dB) P/F —— —— —— —— PASS —— —— —— —— PASS NOTE: The amplitude of spurious emissions which are attenuated by more than 200B below the permissible value has no need to be reported. Distance extrapolation factor =40 log (specific distance/test distance)(dB); Limit line = specific limits(dBuv) + distance extrapolation factor. 1/F., Building B, Zhuoke Science Park, No.190, Chongaing Road, Fuyong Street, Bao‘an District, Shenzhen, Guangdong, China Shenzhen STS TeSt SerViCeS 00‘ Ltd Tel: + 86—755 3688 6288 Faxc+86—755 3688 6277 Hitp://wwni.stsapp.com E~mail: sts@stsapp.com

) 2 Page 18 of 26 Report No.: STS1808209W02 Between 30MHz — 1000 MHz Radiation Spurious Temperature: 26.4 °C Relative Humidity: |55% Test Voltage: DC 4.5V Phase: Horizontal Test Mode: Mode 1 (Model 1 worst) Frequency Reading Correct Result Limit Margin Remark (MHz) (dBuV) Factor(dB/m) (dBuV/m) (dBuV/m) (dB) 30.3173 27.00 —11.35 15.65 40.00 —24.35 aP 67.9130 43.65 —24.15 19.50 40.00 —20.50 aP 104.1701 35.37 —18.84 16.53 43.50 —26.97 aP 239.9873 31.88 —17.76 14.12 46.00 —31.88 aP 541.3725 29.02 —6.97 22.05 46.00 —23.95 aP 866.0880 29.74 —2.63 2711 46.00 —18.89 aP Remark: 1. All readings are Quasi—Peak . 2. Margin = Result (Result =Reading + Factor )—Limit 80.0 dBu¥/m Limit1: — Margin: —— ag 0.0 30.000 40 50 60 70 80 (MHz] 300 400 500 600 700 1000.000 1/F., Building B, Zhuoke Science Park, No.190, Chongaing Road, Fuyong Street, Bao‘an District, Shenzhen, Guangdong, China Shenzhen STS TeSt SerViCeS CO. Ltd Tel: + 86—755 3688 6288 Faxc+86—755 3688 6277 Hitp://wwni.stsapp.com E~mail: sts@stsapp.com

) 2 Page 19 of 26 Report No.: STS1808209W02 Temperature: 26.4 °C Relative Humidity: |55% Test Voltage: DC 4.5V Phase: Vertical Test Mode: Mode 1 (Model 1 worst) Frequency Reading Correct Result Limit Margin Remark (MHz) (dBuV) Factor(dB/m) (dBuV/m) (dBuV/m) (dB) 30.2111 27.63 —11.30 16.33 40.00 —23.67 aP 68.6310 42.18 —24.14 18.04 40.00 —21.96 aP 150.0108 40.08 —17.97 22.11 43.50 —21.39 QP 356.6758 28.21 —13.28 14.93 46.00 —31.07 aP 501.1790 31.52 —8.90 22.62 46.00 —23.38 aP 890.7278 31.15 —2.38 28.77 46.00 —17.23 QP Remark: 1. All readings are Quasi—Peak. 2. Margin = Result (Result =Reading + Factor )—Limit 80.0 dBu¥/m Limit1: — Margin: — 40 0.0 30.000 40 50 60 70 80 (MHz) 300 400 500 600 700 1000.000 1/F., Building B, Zhuoke Science Park, No.190, Chongaing Road, Fuyong Street, Bao‘an District, Shenzhen, Guangdong, China Shenzhen STS Test SerViCeS CO. Ltd Tel: + 86—755 3688 6288 Faxc+86—755 3688 6277 Hitp://wwni.stsapp.com E~mail: sts@stsapp.com

) Page 20 of 26 9 Fundamental frequency: PK Reading Antenna Result Limit Frequency Amplifier Loss Factor(dB) Margin{dB) (dBuV/im> Factor (dBuV/m) (dBu¥V/m) Polarization (MHz) Corr. PEAK (dB) (dB) (dB/m) PEAK PEAK PEAK 2405 99.108 44.40 6.03 27.60 10.77 88.34 114 —25.66 Vertical 2405 97.486 44.40 6.03 27.60 10.77 86.72 114 —27.28 Horizontal AV Reading Antenna Result Limit Frequency Amplifier Loss Factor(dB) Margin{(dB) (dBuV/im> Factor (dBuV/im} (dBuV/im} Polarization (MHz) Corr. AV (dB) (dB) (dB/m) AV AV AV 2405 74.907 44.40 6.03 27.60 10.77 64.14 94 —29.86 Vertical 2405 73.486 44.40 6.03 27.60 10.77 62.72 94 —31.28 Horizontal Note: RBW>20BW; VBW=3xRBW 1/F., Building B, Zhuoke Science Park, No.190, Chongaing Road, Fuyong Street, Bao‘an District, Shenzhen, Guangdong, China Tel: + 86—755 3688 6288 Fax:+86—755 3688 6277 Hitp://wwnstsapp.com E—mail: sts@stsapp.com Shenzhen STS Test Services Co., Ltd.

|) Page 21 of 26 Above 1G Radiation Spurious Antenna Corrected Emission Frequency Reading Amplifier Loss Limits Margin Detector Factor Factor Level Comment (MHz) (cBuVv) (dB) (dB) (dB/im) (dB) (dBuVim) (dBuV/m) (dB) Type 2405 MHz 3264.64 48.22 44.70 6.70 28.20 —9.80 38.42 74.00 —35.58 PK Vertical 3264.64 38.63 44.70 6.70 28.20 —9.80 28.83 54.00 —25.17 AV Vertical 3204.62 48.83 44.70 6.70 28.20 —9.80 39.03 74.00 —34.97 PK Horizontal 3204.62 38.11 44.70 6.70 28.20 —9.80 28.31 54.00 —25.69 AV Horizontal 4810.51 59.10 44.20 9.04 31.60 —3.56 55.54 74.00 —18.46 PK Vertical 4810.51 39.42 44.20 9.04 31.60 —3.56 35.86 54.00 ~18.14 AV Vertical 4810.45 58.31 44.20 9.04 31.60 —3.56 54.75 74.00 —19.25 PK Horizontal 4810.45 38.56 44.20 9.04 31.60 —3.56 35.00 54.00 —19.00 AV Horizontal 5359.61 45.97 44.20 9.86 32.00 —2.34 43.63 74.00 —30.37 PK Vertical 5359.61 37.47 44.20 9.86 32.00 —2.34 35.13 54.00 —18.87 AV Vertical 5359.59 45.28 44.20 9.86 32.00 —2.34 42.94 74.00 —31.06 PK Horizontal 5359.59 38.33 44.20 9.86 32.00 —2.34 35.99 54.00 —18.01 AV Horizontal 7214.96 51.68 43.50 11.40 35.50 3.40 55.08 74.00 —18.92 PK Vertical 7214.96 33.63 43.50 11.40 35.50 3.40 37.03 54.00 —16.97 AV Vertical 7214.95 50.50 43.50 11.40 35.50 3.40 53.90 74.00 —20.10 PK Horizontal 7214.95 32.72 43.50 11.40 35.50 3.40 36.12 54.00 —17.88 AV Horizontal Note: 1) Factor = Antenna Factor + Cable Loss — Pre—amplifier. Emission Level = Reading + Factor The frequency emission of peak points that did not show above the forms are below the limit, the frequency emission is mainly from the environment noise. 1/F., Building B, Zhuoke Science Park, No.190, Chongaing Road, Fuyong Street, Bao‘an District, Shenzhen, Guangdong, China Shenzhen STS TeSt SerViCeS 00‘ Ltd Tel: + 86—755 3688 6288 Faxc+86—755 3688 6277 Hitp://wwni.stsapp.com E~mail: sts@stsapp.com

) Page 22 of 26 9 (Radiation Band edge) Antenna Corrected Emission Frequency Reading Amplifier Loss Limits Margin Detector Factor Factor Level Comment (MHz) (cBuVv) (dB) (dB) (dB/im) (dB) (dBuVim) (dBuV/m) (dB) Type GFSK 2405.00 67.85 43.80 4.91 25.90 12.99 54.86 74 ~19.14 PK Vertical 2405.00 54.39 43.80 4.91 25.90 12.99 41.40 54 —12.60 AV Vertical 2405.00 69.37 43.80 4.91 25.90 12.99 56.38 74 —17.62 PK Horizontal 2405.00 52.92 43.80 4.91 25.90 12.99 39.93 54 —14.07 AV Horizontal 2405.00 69.73 43.80 5.12 25.90 12.78 56.95 74 —17.05 PK Vertical 2405.00 52.80 43.80 5.12 25.90 12.78 40.02 54 —13.98 AV Vertical 2405.00 70.19 43.80 5.12 25.90 12.78 57.41 74 ~16.59 PK Horizontal 2405.00 53.10 43.80 5.12 25.90 12.78 40.32 54 —13.68 AV Horizontal Low measurement frequencies is range from 2310 to 2400 MHz, high measurement frequencies is range from 2483.5 to 2500 MHz. Only show the worst point data of the emissions in the frequency 2310—2400 MHz and 2483.5—2500 MHz. 1/F., Building B, Zhuoke Science Park, No.190, Chongaing Road, Fuyong Street, Bao‘an District, Shenzhen, Guangdong, China Shenzhen STS Test SerViCeS CO. Ltd Tel: + 86—755 3688 6288 Faxc+86—755 3688 6277 Hitp://wwni.stsapp.com E~mail: sts@stsapp.com

Page 23 of 26 Report No.: STS1808209W02 4. BANDWIDTH TEST 4.1 TEST PROCEDURE a. The EUT was directly connected to the spectrum analyzer and antenna output port as show in the block diagram below, b. Spectrum Setting : RBW= 30KHz, VBW≧RBW, Sweep time = Auto. 4.2 TEST SETUP 4.3 EUT OPERATION CONDITIONS TX mode.

3 —Z Page 24 of 26 Report No.: STS1808209W02 4.4 TEST RESULTS Temperature: 25 °C Relative Humidity: 150% Test Voltage: DC 4.5V Test Channel Frequency 20 dBc Bandwidth 99% Bandwidth (MHz) (MHz) (MHz) CHO1 2405 1.058 1.042 2405 MHz mucusuro zeaiem 2ore Genter Freq: 2405000000 GHz Radio Std: None TraceiDetector Trig: Free Run AvglHeld> tort0 #iEGatiLow #Atten: 10 dB Radio Device: BTS 0 dBidiv Ref 10.00 dBm o9 om 103 z3 33 2405 GHz Span 3 BW 30 kHz #VBW 100 kHz Sweep 4.133 Occupied Bandwidth Average 1.0415 MHz Man Transmit Freq Error 391.25 kHz OBW Power 99.00 % x dB Bandwidth 1.058 MHz x dB —20.00 dB 1/F., Building B, Zhuoke Science Park, No.190, Chongging Road, Fuyong Street, Bav‘an District, Shenzhen, Guangdong, China Shenzhen STS Test Services Co., Ltd. Tel: +86—755 3688 6288 Fax:+ 86—755 3688 6277 Hitp://www.stsapp.com E—mail: sts@stsapp.com

Page 25 of 26 Report No.: STS1808209W02 5. ANTENNA REQUIREMENT 5.1 STANDARD REQUIREMENT According to the FCC Part 15 Paragraph 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. 5.2 EUT ANTENNA The EUT antenna is Dipole Antenna.It conforms to the standard requirements.

Page 26 of 26 Report No.: STS1808209W02 APPENDIX- PHOTOS OF TEST SETUP Radiated Measurement Photos ※※※※※END OF THE REPORT※※※※※


Document Created: 2018-09-03 06:18:28
Document Modified: 2018-09-03 06:18:28
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC