Test Report Part 2

FCC ID: KBCIX600-IWL

Test Report

Download: PDF

FCCID_550860

-27- FCC ID:KBCIX600-IWL

1GHz~ 40 GHz (Horizontal), Normal Mode, Channel 9: 5745 MHz
Operator:MailesHsieh RBW:1MHz
Humidity(%):47
Temperature(C):26

Frequency Rx_R. Ant_F. Cab_L. PreAmpl Emission Limit Margin A.Tower T.Table
MHz dBuV dB/m dB dB dBuV/m dBuV/m dB cm deg
2485.31 48.97pk 30.90 1.44 35.20 46.11pk 54.00av -7.89 101 195
3355.64 49.10pk 31.38 1.63 35.53 46.60pk 54.00av -7.40 103 266
3826.77 49.76pk 31.96 1.97 36.83 46.85pk 54.00av -7.15 102 145
4420.18 46.87pk 33.46 2.05 37.36 45.02pk 54.00av -8.98 101 58

1GHz~ 40 GHz (Vertical), Normal Mode, Channel 9: 5745 MHz
Operator:MailesHsieh RBW:1MHz
Humidity(%):47
Temperature(C):26

Frequency Rx_R. Ant_F. Cab_L. PreAmpl Emission Limit Margin A.Tower T.Table
MHz dBuV dB/m dB dB dBuV/m dBuV/m dB cm deg
1841.56 48.60pk 29.67 2.48 34.87 45.88pk 54.00av -8.12 100 54
2190.41 47.23pk 30.96 2.02 35.19 45.03pk 54.00av -8.97 101 103
2488.91 48.98pk 30.90 1.42 35.20 46.10pk 54.00av -7.90 101 197
3826.77 53.27pk 31.96 1.97 36.83 50.36pk 54.00av -3.64 102 145
7459.14 43.53pk 39.83 2.29 36.43 49.23pk 54.00av -4.77 101 176

Note: “ * ”: Fundamental Frequency
“ pk”: peak reading
“av”: average reading
The Spectrum noise level+Correction Factor<Limit-6 dB
Margin = Corrected Amplitude – Limit
Corrected Amplitude=Radiated Amplitude+Antenna Correction Factor+Cable Loss-Pre-Amplifier Gain
A margin of -8dB means that the emission is 8dB below the limit.
All frequencies from 1GHz to 40 GHz have been tested.

International Standards Laboratory Report Number: 05LR008FC
HC LAB:NVLAP:200234-0;VCCI: R-341,C-354;NEMKO:ELA 113a,113c;BSMI:SL2-IN-E-0037;SL2-R1-E-0037;CNLA:1178
LT LAB:NVLAP:200234-0;VCCI: R-1435,C-1440;NEMKO:ELA 113b,113d;BSMI:SL2-IN-E-0013;CNLA:0997

-28- FCC ID:KBCIX600-IWL

1GHz~ 40 GHz (Horizontal), Normal Mode, Channel 12 : 5805 MHz
Operator:MailesHsieh RBW:1MHz
Humidity(%):47
Temperature(C):26

Frequency Rx_R. Ant_F. Cab_L. PreAmpl Emission Limit Margin A.Tower T.Table
MHz dBuV dB/m dB dB dBuV/m dBuV/m dB cm deg
2233.57 48.11pk 30.95 1.89 35.19 45.76pk 54.00av -8.24 101 116
2496.10 48.02pk 30.90 1.38 35.20 45.11pk 54.00av -8.89 101 199
3057.14 48.12pk 31.15 1.48 34.87 45.87pk 54.00av -8.13 103 342
3355.64 49.58pk 31.38 1.63 35.53 47.07pk 54.00av -6.93 103 266

1GHz~ 40 GHz (Vertical), Normal Mode, Channel 12 : 5805 MHz
Operator:MailesHsieh RBW:1MHz
Humidity(%):47
Temperature(C):26

Frequency Rx_R. Ant_F. Cab_L. PreAmpl Emission Limit Margin A.Tower T.Table
MHz dBuV dB/m dB dB dBuV/m dBuV/m dB cm deg
1064.74 52.64pk 24.80 2.18 33.96 45.65pk 54.00av -8.35 102 108
1837.96 48.01pk 29.64 2.48 34.86 45.26pk 54.00av -8.74 100 54
2496.10 48.27pk 30.90 1.38 35.20 45.36pk 54.00av -8.64 101 199
3866.33 49.74pk 32.01 2.00 36.95 46.80pk 54.00av -7.20 102 134
7459.14 43.48pk 39.83 2.29 36.43 49.18pk 54.00av -4.82 101 176

Note: “ * ”: Fundamental Frequency
“ pk”: peak reading
“av”: average reading
The Spectrum noise level+Correction Factor<Limit-6 dB
Margin = Corrected Amplitude – Limit
Corrected Amplitude=Radiated Amplitude+Antenna Correction Factor+Cable Loss-Pre-Amplifier Gain
A margin of -8dB means that the emission is 8dB below the limit.
All frequencies from 1GHz to 40 GHz have been tested.

International Standards Laboratory Report Number: 05LR008FC
HC LAB:NVLAP:200234-0;VCCI: R-341,C-354;NEMKO:ELA 113a,113c;BSMI:SL2-IN-E-0037;SL2-R1-E-0037;CNLA:1178
LT LAB:NVLAP:200234-0;VCCI: R-1435,C-1440;NEMKO:ELA 113b,113d;BSMI:SL2-IN-E-0013;CNLA:0997

-33- FCC ID:KBCIX600-IWL

4.6.5 Test Setup (Radiated)

3M

1~4M

Antenna and
turntable
distance
Load EUT 3 m.
Active To Spectrum

To remote
controller

Metal Full Soldered Ground Plane

To
turntable
Remote
To Antenna
Controller

Printer Control PC Spectrum

International Standards Laboratory Report Number: 05LR008FC
HC LAB:NVLAP:200234-0;VCCI: R-341,C-354;NEMKO:ELA 113a,113c;BSMI:SL2-IN-E-0037;SL2-R1-E-0037;CNLA:1178
LT LAB:NVLAP:200234-0;VCCI: R-1435,C-1440;NEMKO:ELA 113b,113d;BSMI:SL2-IN-E-0013;CNLA:0997

-34- FCC ID:KBCIX600-IWL

4.6.6 Test Data (Radiated):

Band Edge measurement (Radiated)
Temperature (℃):25
Test Engineer:Mailes Hsieh Humidity (%):46
Outside Frequency Spectrum Correction Emission Limit
Channel (MHz) Reading Factor Level (dBuV/m) Pass/Fail
(Normal) (dBuV) (dB/m) (dBuV/m)
1
5145.0 23.55 39.03 62.58 74 Pass
(Peak)
1
5150.0 9.16 39.03 48.19 54 Pass
(Average)
8
5355.8 24.07 39.34 63.41 74 Pass
(Peak)
8
5351.5 9.45 39.34 48.79 54 Pass
(Average)
9
5710.4 23.88 39.41 63.29 74 Pass
(Peak)
9
5715.0 9.72 39.41 49.13 54 Pass
(Average)
12
5836.1 23.56 39.42 62.98 74 Pass
(Peak)
12
5836.1 9.84 39.42 49.26 54 Pass
(Average)

Note: “pk”: peak reading
“av”: average reading
Emission Level=Spectrum Reading+Correction Factor
Correction Factor =Antenna Factor+cable loss
Both Horizontal and Vertical polarization have been tested and the worst data is listed above.

International Standards Laboratory Report Number: 05LR008FC
HC LAB:NVLAP:200234-0;VCCI: R-341,C-354;NEMKO:ELA 113a,113c;BSMI:SL2-IN-E-0037;SL2-R1-E-0037;CNLA:1178
LT LAB:NVLAP:200234-0;VCCI: R-1435,C-1440;NEMKO:ELA 113b,113d;BSMI:SL2-IN-E-0013;CNLA:0997

-39- FCC ID:KBCIX600-IWL

4.7 RF Exposure Measurement [Section 15.407(f)(4) & 1.1307(b)]
Refer to MPE Test Report

International Standards Laboratory Report Number: 05LR008FC
HC LAB:NVLAP:200234-0;VCCI: R-341,C-354;NEMKO:ELA 113a,113c;BSMI:SL2-IN-E-0037;SL2-R1-E-0037;CNLA:1178
LT LAB:NVLAP:200234-0;VCCI: R-1435,C-1440;NEMKO:ELA 113b,113d;BSMI:SL2-IN-E-0013;CNLA:0997

-40- FCC ID:KBCIX600-IWL

4.8 Frequency Stability [Section 15.407(g)]

4.8.1 Limits of Frequency Stability Measurement
The frequency tolerance of the carrier sing shall be maintained within +/- 0.02% of the
operating frequency over the operation temperature range of EUT (00C~350C), and
variation in the primary supply voltage from 85% to 115% of the rated supply voltage
(115V AC) at 200C.

4.8.2 Test Procedure
1. The EUT was placed in the Temperature/Humidity Chamber and powered by a
Voltage/Frequency Power converter.
2. Connect the RF output of EUT to Spectrum. Turn on the EUT.
3. Turn the EUT off and set the chamber to the highest temperature specified.
4. Allow sufficient time (approximately 30 min) for the chamber temperature to
stabilize. Turn the EUT on and measure the operating frequency after 2, 5, 10
minutes.
5. Set the Voltage/Frequency Power Converter to 85% and 115% of supply voltage,
then repeat step 2, 3, 4 respectively.
6. Repeat step 2 , 3, 4, 5 with the temperature of chamber set to the lowest temperature.
7. Repeat step 2 , 3, 4, 5 with the temperature of chamber set to 200C.

4.8.3 Test Setup

Temperature/Humidity
Chamber

Spectrum
EUT Analyzer

Voltage/Frequency
TT Power Converter

International Standards Laboratory Report Number: 05LR008FC
HC LAB:NVLAP:200234-0;VCCI: R-341,C-354;NEMKO:ELA 113a,113c;BSMI:SL2-IN-E-0037;SL2-R1-E-0037;CNLA:1178
LT LAB:NVLAP:200234-0;VCCI: R-1435,C-1440;NEMKO:ELA 113b,113d;BSMI:SL2-IN-E-0013;CNLA:0997

-41- FCC ID:KBCIX600-IWL

4.8.4 Test Data
Test Engineer:Mailes
Hsieh
Operating Frequency: 5180(Mhz) Limit: +/- 0.02%
Power
Temp. 2 minutes 5 minutes 10 minutes
Supply
(0C) (V AC) (MHz) (%) (MHz) (%) (MHz)
132 5180.0018 0.0000 5180.0050 0.0001 5180.0208 0.0004
35 115 5180.0050 0.0001 5180.0122 0.0002 5180.0212 0.0004
97 5180.0036 0.0001 5180.0120 0.0002 5180.0013 0.0000
132 5180.0050 0.0001 5180.0155 0.0003 5180.0094 0.0002
0 115 5180.0111 0.0002 5180.0233 0.0004 5180.0200 0.0004
97 5180.0307 0.0006 5180.0193 0.0004 5180.0202 0.0004
132 5180.0043 0.0001 5180.0124 0.0002 5180.0087 0.0002
20 115 5180.0108 0.0002 5180.0172 0.0003 5180.0121 0.0002
97 5179.9932 -0.0001 5180.0249 0.0005 5179.9960 -0.0001

International Standards Laboratory Report Number: 05LR008FC
HC LAB:NVLAP:200234-0;VCCI: R-341,C-354;NEMKO:ELA 113a,113c;BSMI:SL2-IN-E-0037;SL2-R1-E-0037;CNLA:1178
LT LAB:NVLAP:200234-0;VCCI: R-1435,C-1440;NEMKO:ELA 113b,113d;BSMI:SL2-IN-E-0013;CNLA:0997

-42- FCC ID:KBCIX600-IWL

5. TEST RESULTS (802.11b)
5.1 Powerline Conducted Emissions [Section 15.207]

5.1.1 EUT Configuration
The conducted emission test setups are in accordance with Figs 9, 10(a) and 10(b) of ANSI
C63.4-2001, CFR 47 Part 15 Subpart B; or EN55022:1994/ A1:1995/A2:1997; CISPR
22:1993/A1:1995/A2:1996.
The EUT was set up on the non-conductive table that is 1.0 by 1.5 meter, 80cm above
ground. The wall of the shielded room was located 40cm to the rear of the EUT.
Power to the EUT was provided through the LISN. The impedance vs. frequency
characteristic of the LISN is complied with the limit shown on the figure 1 of ANSI
C63.4-2001.
Both lines (neutral and hot) were connected to the LISN in series at testing. A coaxial-type
connector which provides one 50 ohms terminating impedance was provided for connecting
the test instrument. The excess length of the power cord was folded back and forth at the
center of the lead so as to form a bundle not exceeding 40cm in length.
Any changes made to the configuration, or modifications made to the EUT, during testing are
noted in the following test record.
If the EUT is a Personal Computer or a peripheral of personal computer, and the personal
computer has an auxiliary AC outlet which can be used for providing power to an external
monitor, then all measurements will be made with the monitor power from first the
computer-mounted AC outlet and then a floor-mounted AC outlet.

5.1.2 Test Procedure
The system was set up as described above, with the EMI diagnostic software running. The
main power line conducted EMI tests were run on the hot and neutral conductors of the
power cord and the results were recorded. The effect of varying the position of the interface
cables has been investigated to find the configuration that produces maximum emission.
At the frequencies where the peak values of the emissions were higher than 6dß below the
applicable limits, the emissions were also measured with the quasi-peak detectors. At the
frequencies where the quasi-peak values of the emissions were higher than 6dß below the
applicable average limits, the emissions were also measured with the average detectors.
The highest emissions were analyzed in details by operating the spectrum analyzer in fixed
tuned mode to determine the nature of the emissions and to provide information which could
be useful in reducing their amplitude.

5.1.3 EMI Receiver/Spectrum Analyzer Configuration (for the frequencies tested)
Frequency Range 150 KHz--30MHz
Detector Function Quasi-Peak/Average
Bandwidth (RBW) 9KHz

International Standards Laboratory Report Number: 05LR008FC
HC LAB:NVLAP:200234-0;VCCI: R-341,C-354;NEMKO:ELA 113a,113c;BSMI:SL2-IN-E-0037;SL2-R1-E-0037;CNLA:1178
LT LAB:NVLAP:200234-0;VCCI: R-1435,C-1440;NEMKO:ELA 113b,113d;BSMI:SL2-IN-E-0013;CNLA:0997

-43- FCC ID:KBCIX600-IWL

5.1.4 Test Data:
Power Line Conducted Emissions (Hot) Channel 1, 6, 11
Operator:MailesHsieh
Temperature(C):25
12:22:40PM,Tuesday,May03,2005 Humidity(%):57

Frequency LISNLoss CableLoss QPCorrct. QPLimit QPMargin AVECorrct. AVELimit AVEMargin
MHz (dB) (dB) Amp.(dBuV) (dBuV) (dB) Amp.(dBuV) (dBuV) (dB)
0.50148 0.12 0.07 33.31 56.00 -22.69 31.92 46.00 -14.08
0.64173 0.14 0.07 27.79 56.00 -28.21 25.48 46.00 -20.52
0.716 0.15 0.07 31.14 56.00 -24.86 29.21 46.00 -16.79
0.8614 0.18 0.07 31.63 56.00 -24.37 29.90 46.00 -16.10
0.93305 0.19 0.07 29.65 56.00 -26.35 26.94 46.00 -19.06
2.21976 0.20 0.10 30.53 56.00 -25.47 24.26 46.00 -21.74
2.64956 0.20 0.11 33.70 56.00 -22.30 23.72 46.00 -22.28
2.86506 0.20 0.11 34.66 56.00 -21.34 24.53 46.00 -21.47
19.7082 0.78 0.34 35.69 60.00 -24.31 31.07 50.00 -18.93
22.5695 0.85 0.33 48.32 60.00 -11.68 48.21 50.00 -1.79

Limit_QP
CISPR22 Class B Band1_1
International Standards Laboratory Conduction 02 Band2_1
Phase Class B Test Graph Limit_AV
80.0
PK Read
QP Read
70.0
Amplitude ( dBuV )

AVG Read
60.0

50.0

40.0

30.0

20.0

10.0

0
100.0K 1.0M 10.0M 100.0M

Frequency ( Hz )
Operator: Mailes Hsieh

International Standards Laboratory Report Number: 05LR008FC
HC LAB:NVLAP:200234-0;VCCI: R-341,C-354;NEMKO:ELA 113a,113c;BSMI:SL2-IN-E-0037;SL2-R1-E-0037;CNLA:1178
LT LAB:NVLAP:200234-0;VCCI: R-1435,C-1440;NEMKO:ELA 113b,113d;BSMI:SL2-IN-E-0013;CNLA:0997

-44- FCC ID:KBCIX600-IWL
Power Line Conducted Emissions (Neutral) Channel 1, 6, 11
Operator:MailesHsieh
Temperature(C):25
12:32:07PM,Tuesday,May03,2005 Humidity(%):57

Frequency LISNLoss CableLoss QPCorrct. QPLimit QPMargin AVECorrct. AVELimit AVEMargin
MHz (dB) (dB) Amp.(dBuV) (dBuV) (dB) Amp.(dBuV) (dBuV) (dB)
0.50111 0.12 0.07 31.41 56.00 -24.59 29.79 46.00 -16.21
0.644 0.14 0.07 28.01 56.00 -27.99 25.18 46.00 -20.82
0.7187 0.15 0.07 27.88 56.00 -28.12 26.07 46.00 -19.93
0.86165 0.18 0.07 29.16 56.00 -26.84 26.79 46.00 -19.21
0.93216 0.19 0.07 29.56 56.00 -26.44 26.07 46.00 -19.93
2.2918 0.20 0.10 32.41 56.00 -23.59 25.16 46.00 -20.84
2.43456 0.20 0.10 32.14 56.00 -23.86 21.35 46.00 -24.65
2.65053 0.20 0.11 34.05 56.00 -21.95 23.73 46.00 -22.27
2.86483 0.20 0.11 34.91 56.00 -21.09 24.34 46.00 -21.66
22.5697 0.40 0.33 47.71 60.00 -12.29 47.55 50.00 -2.45

Limit_QP
CISPR22 Class B Limit_AV
International Standards Laboratory Conduction 02 NBand1_1
Neutral Class B Test Graph NBand2_1
80.0
PK Read
QP Read
70.0
Amplitude ( dBuV )

AVG Read
60.0

50.0

40.0

30.0

20.0

10.0

0
100.0K 1.0M 10.0M 100.0M

Frequency ( Hz )
Operator: Mailes Hsieh
* NOTE: During the test, the EMI receiver was set to Max. Hold then switch the EUT Channel between 1 , 6, 11
to get the maximum reading of all these channels.
Margin = Amplitude + Insertion Loss- Limit
A margin of -8dB means that the emission is 8dB below the limit

International Standards Laboratory Report Number: 05LR008FC
HC LAB:NVLAP:200234-0;VCCI: R-341,C-354;NEMKO:ELA 113a,113c;BSMI:SL2-IN-E-0037;SL2-R1-E-0037;CNLA:1178
LT LAB:NVLAP:200234-0;VCCI: R-1435,C-1440;NEMKO:ELA 113b,113d;BSMI:SL2-IN-E-0013;CNLA:0997

-45- FCC ID:KBCIX600-IWL

5.2 Bandwidth for DSSS [Section 15.247 (a)(2)]

5.2.1 Test Procedure
The Transmitter output of EUT was connected to the spectrum analyzer. The 6 dB bandwidth
of the fundamental frequency was measured. The setting of spectrum analyzer is as follows
Equipment mode Spectrum analyzer
Detector function Peak mode
RBW 100KHz
VBW 100KHz

5.2.2 Test Setup

Spectrum
EUT Analyzer

5.2.3 Test Data:
6dB Bandwidth
Temperature (℃):24
Test Engineer:Mailes Hsieh Humidity (%):54

6dB
Frequency Limit
Channel Bandwidth Pass/Fail
(MHz) (MHz) (MHz)
1 2412 9.20 0.5 Pass
6 2437 9.24 0.5 Pass
11 2462 9.20 0.5 Pass

International Standards Laboratory Report Number: 05LR008FC
HC LAB:NVLAP:200234-0;VCCI: R-341,C-354;NEMKO:ELA 113a,113c;BSMI:SL2-IN-E-0037;SL2-R1-E-0037;CNLA:1178
LT LAB:NVLAP:200234-0;VCCI: R-1435,C-1440;NEMKO:ELA 113b,113d;BSMI:SL2-IN-E-0013;CNLA:0997

-48- FCC ID:KBCIX600-IWL

5.3 DSSS Maximum Peak Output Power [Section 15.247 (b)(1)]

5.3.1 Test Procedure
The Transmitter output of EUT was connected to the peak power analyzer.

5.3.2 Test Setup

EUT Peak Power
Analyzer

5.3.3 Test Data
Maximum Peak Output Power
Temperature (℃):24
Test Engineer:Mailes Hsieh Humidity (%):54

Analyzer Peak Power Peak Power
Frequency Cable Loss Limit
Channel Reading Output Output Pass/Fail
(Mhz) (dBm) (dB) (mW) (dBm) (dBm)
1 2412 17.10 1.10 66.07 18.20 30 Pass
6 2437 18.24 1.10 85.90 19.34 30 Pass
11 2462 18.58 1.10 92.90 19.68 30 Pass

Note: Two RF output( MAIN & AUX) have been test,the worse data shown above.

International Standards Laboratory Report Number: 05LR008FC
HC LAB:NVLAP:200234-0;VCCI: R-341,C-354;NEMKO:ELA 113a,113c;BSMI:SL2-IN-E-0037;SL2-R1-E-0037;CNLA:1178
LT LAB:NVLAP:200234-0;VCCI: R-1435,C-1440;NEMKO:ELA 113b,113d;BSMI:SL2-IN-E-0013;CNLA:0997

-49- FCC ID:KBCIX600-IWL

5.4 Radiated Emission Measurement [Section [15.247(c)(4)]

5.4.1 EUT Configuration
The equipment under test was set up on the 10 meter chamber with measurement distance of
3 meters. The EUT was placed on a non-conductive table 80cm above ground.
Any changes made to the configuration, or modifications made to the EUT, during testing are
noted in the following test record.

5.4.2 Test Procedure

The system was set up as described above, with the EMI diagnostic software running. We
found the maximum readings by varying the height of antenna and then rotating the turntable.
Both polarization of antenna, horizontal and vertical, are measured.
30M to 1GHz: The highest emissions between 30 MHz to 1000 MHz were also analyzed in
details by operating the spectrum analyzer and/or EMI receiver in quasi-peak mode to
determine the precise amplitude of the emissions. While doing so, the interconnecting cables
and major parts of the system were moved around, the antenna height was varied between
one and four meters, its polarization was varied between vertical and horizontal, and the
turntable was slowly rotated, to maximize the emission.
1GHz – 25GHz: The highest emissions were also analyzed in details by operating the
spectrum analyzer and/or EMI receiver in peak mode to determine the precise amplitude of
the emission. While doing so, the interconnecting cables and major parts of the system were
moved around, the antenna height was varied between one and four meters, its polarization
was varied between vertical and horizontal, and the turntable was slowly rotated, to
maximize the emission. During test the EMI receiver and spectrum was setup according to
EMI Receiver/Spectrum Analyzer Configuration.
For the test of 2nd to 10th harmonics frequencies , the equipment setup was also refer to EMI
Receiver/Spectrum Analyzer Configuration. The frequencies were tested using Peak mode
first, if the test data is higher than the emissions limit, an additional measurement using
Average mode will be performed and the average reading will be compared to the limit and
record in test report.

5.4.3 EMI Receiver/Spectrum Analyzer Configuration (for the frequencies tested)
Frequency Range Tested: 30MHz~1000MHz
Detector Function: Quasi-Peak Mode
Resolution Bandwidth (RBW): 120KHz
Video Bandwidth (VBW) 1MHz

Frequency Range Tested: 1GHz – 25 GHz
Detector Function: Peak Mode
Resolution Bandwidth (RBW): 1MHz
Video Bandwidth (VBW) 3MHz

Frequency Range Tested: 1GHz – 25 GHz
Detector Function: Average Mode
Resolution Bandwidth (RBW): 1MHz
Video Bandwidth (VBW) 10 Hz

International Standards Laboratory Report Number: 05LR008FC
HC LAB:NVLAP:200234-0;VCCI: R-341,C-354;NEMKO:ELA 113a,113c;BSMI:SL2-IN-E-0037;SL2-R1-E-0037;CNLA:1178
LT LAB:NVLAP:200234-0;VCCI: R-1435,C-1440;NEMKO:ELA 113b,113d;BSMI:SL2-IN-E-0013;CNLA:0997

-50- FCC ID:KBCIX600-IWL

5.4.4 Test Data (30MHz – 1GHz):
30M – 1GHz Open Field Radiated Emissions (Horizontal) Channel 1, 6, 11
Operator:MailesHsieh
Temperature(C):24
Humidity(%):47

Frequency RxAmp. AntFact CableLoss PreAmpGain Corrct.Emi. Limit
Margin Ant.Pos. TablePos
.
MHz (dBuV) (dB/m) (dB) (dB) (dBuV/m) (dBuV/m) (dB) (cm) (deg)
231.76 23.23 9.21 2.95 0.00 35.39 46.00 -10.61 101.00 87.00
282.20 19.37 13.09 3.39 0.00 35.86 46.00 -10.14 101.00 54.00
306.45 18.27 13.69 3.68 0.00 35.64 46.00 -10.36 101.00 6.00
355.92 16.77 14.49 4.15 0.00 35.41 46.00 -10.59 101.00 349.00
364.65 21.14 14.77 4.20 0.00 40.11 46.00 -5.89 101.00 22.00
432.55 16.82 16.16 4.69 0.00 37.67 46.00 -8.33 101.00 22.00
629.46 7.07 18.96 6.15 0.00 32.18 46.00 -13.82 101.00 54.00
696.39 8.74 19.00 6.60 0.00 34.34 46.00 -11.66 101.00 333.00
766.23 3.98 20.10 7.07 0.00 31.15 46.00 -14.85 101.00 333.00
833.16 5.21 20.43 7.71 0.00 33.35 46.00 -12.65 101.00 22.00

30M – 1GHz Open Field Radiated Emissions (Vertical) Channel 1, 6, 11
Operator:MailesHsieh
Temperature(C):24
Humidity(%):47

Frequency RxAmp. AntFact CableLoss PreAmpGain Corrct.Emi. Limit
Margin Ant.Pos. TablePos
.
MHz (dBuV) (dB/m) (dB) (dB) (dBuV/m) (dBuV/m) (dB) (cm) (deg)
282.20 17.24 13.09 3.39 0.00 33.72 46.00 -12.28 101.00 348.00
366.59 24.28 14.83 4.22 0.00 43.33 46.00 -2.67 101.00 84.00
432.55 20.41 16.16 4.69 0.00 41.26 46.00 -4.74 101.00 17.00
544.10 11.20 18.65 5.49 0.00 35.33 46.00 -10.67 101.00 299.00
566.41 10.32 18.83 5.65 0.00 34.81 46.00 -11.19 101.00 133.00
629.46 14.88 18.96 6.15 0.00 40.00 46.00 -6.00 101.00 348.00
686.69 10.55 19.00 6.53 0.00 36.08 46.00 -9.92 101.00 315.00
699.30 14.03 19.00 6.62 0.00 39.65 46.00 -6.35 101.00 315.00
715.79 8.05 19.35 6.76 0.00 34.16 46.00 -11.84 101.00 348.00
830.25 7.51 20.40 7.70 0.00 35.61 46.00 -10.39 101.00 315.00

NOTE:
?? During the Pre-test, the EUT has been tested for Channel 1 , 6, 11 transmit from Main and Aux antenna respectively
to get all the critical emission frequencies. In the final test all the critical emission frequencies has been tested and the test
data are listed above.
?? Margin = Corrected Amplitude – Limit
Corrected Amplitude = Radiated Amplitude + Antenna Correction Factor + Cable Loss - Pre-Amplifier Gain
A margin of -8dB means that the emission is 8dB below the limit
All frequencies from 30MHz to 1GHz have been tested

International Standards Laboratory Report Number: 05LR008FC
HC LAB:NVLAP:200234-0;VCCI: R-341,C-354;NEMKO:ELA 113a,113c;BSMI:SL2-IN-E-0037;SL2-R1-E-0037;CNLA:1178
LT LAB:NVLAP:200234-0;VCCI: R-1435,C-1440;NEMKO:ELA 113b,113d;BSMI:SL2-IN-E-0013;CNLA:0997

-51- FCC ID:KBCIX600-IWL

5.4.5 Test Data ( 1GHz – 25 GHz) .
1GHz~ 25 GHz (Horizontal), Channel 1: 2412 MHz
Operator:MailesHsieh RBW:1MHz
Humidity(%):47
Temperature(C):26

Frequency Rx_R. Ant_F. Cab_L. PreAmpl Emission Limit Margin A.Tower T.Table
MHz dBuV dB/m dB dB dBuV/m dBuV/m dB cm deg
1359.64 50.60pk 26.15 2.21 34.12 44.84pk 54.00av -9.16 101 87
1399.60 51.81pk 26.34 2.22 34.15 46.22pk 54.00av -7.78 101 84
2488.51 48.09pk 30.90 1.42 35.20 45.21pk 54.00av -8.79 101 196
3357.64 49.42pk 31.39 1.64 35.53 46.91pk 54.00av -7.09 103 265
6426.57 46.20pk 36.31 3.36 37.73 48.13pk 54.00av -5.87 100 211

1GHz~ 25 GHz (Vertical), Channel 1: 2412 MHz
Operator:MailesHsieh RBW:1MHz
Humidity(%):47
Temperature(C):26

Frequency Rx_R. Ant_F. Cab_L. PreAmpl Emission Limit Margin A.Tower T.Table
MHz dBuV dB/m dB dB dBuV/m dBuV/m dB cm deg
1064.94 54.80pk 24.80 2.18 33.97 47.81pk 54.00av -6.19 102 108
1362.14 50.14pk 26.17 2.21 34.13 44.39pk 54.00av -9.61 101 87
1841.66 49.18pk 29.67 2.48 34.87 46.46pk 54.00av -7.54 100 54
2488.51 48.40pk 30.90 1.42 35.20 45.52pk 54.00av -8.48 101 196
4872.01 47.51pk 35.55 2.17 37.89 47.33pk 54.00av -6.67 100 1
6426.57 48.80pk 36.31 3.36 37.73 50.74pk 54.00av -3.26 100 211

Note:
?? According to ANSI C63.4-2001 8.3.1.2 Notes(1):Where limits are specified by agencies for both average and peak (or
quasi-peak) detection , if the peak (or quasi-peak) measured value complies with the average limit , it is unnecessary to
perform an average measurement.
?? “ * ”: Fundamental Frequency
?? “**”: Not in the restricted band, Limit level=Fundamental Emission-20dB
?? “ pk”: peak mode
?? “av”: average mode
?? “---“: No meter reading data due to the emission level is smaller than spectrum noise level.
?? The Spectrum noise level+Correction Factor < Limit - 6 dB
?? Margin=Corrected Amplitude – Limit
?? Corrected Amplitude=Radiated Amplitude+Antenna Correction Factor+Cable Loss-Pre-Amplifier Gain
?? A margin of -8dB means that the emission is 8dB below the limit.
All frequencies from 1GHz to 25 GHz have been tested.

International Standards Laboratory Report Number: 05LR008FC
HC LAB:NVLAP:200234-0;VCCI: R-341,C-354;NEMKO:ELA 113a,113c;BSMI:SL2-IN-E-0037;SL2-R1-E-0037;CNLA:1178
LT LAB:NVLAP:200234-0;VCCI: R-1435,C-1440;NEMKO:ELA 113b,113d;BSMI:SL2-IN-E-0013;CNLA:0997

-52- FCC ID:KBCIX600-IWL

1GHz~ 25 GHz (Horizontal) , Channel 6 : 2437 MHz
Operator:MailesHsieh RBW:1MHz
Humidity(%):47
Temperature(C):26

Frequency Rx_R. Ant_F. Cab_L. PreAmpl Emission Limit Margin A.Tower T.Table
MHz dBuV dB/m dB dB dBuV/m dBuV/m dB cm deg
1064.94 52.23pk 24.80 2.18 33.97 45.24pk 54.00av -8.76 102 108
1399.6 050.76pk 26.34 2.22 34.15 45.17pk 54.00av -8.83 101 84
2488.51 47.45pk 30.90 1.42 35.20 44.57pk 54.00av -9.43 101 196
3357.64 49.52pk 31.39 1.64 35.53 47.02pk 54.00av -6.98 103 265
6493.01 49.39pk 36.39 3.40 37.68 51.50pk 54.00av -2.50 100 199

1GHz~ 25 GHz (Vertical), Channel 6 : 2437 MHz
Operator:MailesHsieh RBW:1MHz
Humidity(%):47
Temperature(C):26

Frequency Rx_R. Ant_F. Cab_L. PreAmpl Emission Limit Margin A.Tower T.Table
MHz dBuV dB/m dB dB dBuV/m dBuV/m dB cm deg
1329.67 50.63pk 26.02 2.21 34.11 44.74pk 54.00av -9.26 101 89
1399.60 51.65pk 26.34 2.22 34.15 46.06pk 54.00av -7.94 101 84
1841.66 49.84pk 29.67 2.48 34.87 47.13pk 54.00av -6.87 100 54
2491.01 47.98pk 30.90 1.41 35.20 45.09pk 54.00av -8.91 101 197
4972.03 46.78pk 35.49 2.16 37.88 46.56pk 54.00av -7.44 100 3
6493.01 50.41pk 36.39 3.40 37.68 52.52pk 54.00av -1.48 100 199

Note:
?? According to ANSI C63.4-2001 8.3.1.2 Notes(1):Where limits are specified by agencies for both average and peak (or
quasi-peak) detection , if the peak (or quasi-peak) measured value complies with the average limit , it is unnecessary to
perform an average measurement.
?? “ * ”: Fundamental Frequency
?? “**”: Not in the restricted band, Limit level=Fundamental Emission-20dB
?? “ pk”: peak mode
?? “av”: average mode
?? “---“: No meter reading data due to the emission level is smaller than spectrum noise level.
?? The Spectrum noise level+Correction Factor < Limit - 6 dB
?? Margin=Corrected Amplitude – Limit
?? Corrected Amplitude=Radiated Amplitude+Antenna Correction Factor+Cable Loss-Pre-Amplifier Gain
?? A margin of -8dB means that the emission is 8dB below the limit.
All frequencies from 1GHz to 25 GHz have been tested.

International Standards Laboratory Report Number: 05LR008FC
HC LAB:NVLAP:200234-0;VCCI: R-341,C-354;NEMKO:ELA 113a,113c;BSMI:SL2-IN-E-0037;SL2-R1-E-0037;CNLA:1178
LT LAB:NVLAP:200234-0;VCCI: R-1435,C-1440;NEMKO:ELA 113b,113d;BSMI:SL2-IN-E-0013;CNLA:0997

-53- FCC ID:KBCIX600-IWL

1GHz~ 25 GHz (Horizontal), Channel 11: 2462 MHz
Operator:MailesHsieh RBW:1MHz
Humidity(%):47
Temperature(C):26

Frequency Rx_R. Ant_F. Cab_L. PreAmpl Emission Limit Margin A.Tower T.Table
MHz dBuV dB/m dB dB dBuV/m dBuV/m dB cm deg
1397.10 50.01pk 26.33 2.22 34.14 44.41pk 54.00av -9.59 101 85
1794.21 46.38pk 29.27 2.45 34.78 43.32pk 54.00av -10.68 100 57
2496.00 48.18pk 30.90 1.38 35.20 45.26pk 54.00av -8.74 101 199
3357.64 49.24pk 31.39 1.64 35.53 46.73pk 54.00av -7.27 103 265
6562.94 46.20pk 36.74 3.36 37.62 48.69pk 54.00av -5.31 101 187

1GHz~ 25 GHz (Vertical), Channel 11 : 2462 MHz
Operator:MailesHsieh RBW:1MHz
Humidity(%):47
Temperature(C):26

Frequency Rx_R. Ant_F. Cab_L. PreAmpl Emission Limit Margin A.Tower T.Table
MHz dBuV dB/m dB dB dBuV/m dBuV/m dB cm deg
1062.44 52.77pk 24.79 2.18 33.96 45.77pk 54.00av -8.23 102 108
1399.60 52.01pk 26.34 2.22 34.15 46.42pk 54.00av -7.58 101 84
1841.66 48.97pk 29.67 2.48 34.87 46.25pk 54.00av -7.75 100 54
2491.01 48.91pk 30.90 1.41 35.20 46.02pk 54.00av -7.98 101 197
4989.51 46.77pk 35.56 2.17 37.90 46.59pk 54.00av -7.41 100 1
6559.44 49.02pk 36.72 3.36 37.62 51.49pk 54.00av -2.51 101 187

Note:
?? According to ANSI C63.4-2001 8.3.1.2 Notes(1):Where limits are specified by agencies for both average and peak (or
quasi-peak) detection , if the peak (or quasi-peak) measured value complies with the average limit , it is unnecessary to
perform an average measurement.
?? “ * ”: Fundamental Frequency
?? “**”: Not in the restricted band, Limit level=Fundamental Emission-20dB
?? “ pk”: peak mode
?? “av”: average mode
?? “---“: No meter reading data due to the emission level is smaller than spectrum noise level.
?? The Spectrum noise level+Correction Factor < Limit - 6 dB
?? Margin=Corrected Amplitude – Limit
?? Corrected Amplitude=Radiated Amplitude+Antenna Correction Factor+Cable Loss-Pre-Amplifier Gain
?? A margin of -8dB means that the emission is 8dB below the limit.
All frequencies from 1GHz to 25 GHz have been tested.

International Standards Laboratory Report Number: 05LR008FC
HC LAB:NVLAP:200234-0;VCCI: R-341,C-354;NEMKO:ELA 113a,113c;BSMI:SL2-IN-E-0037;SL2-R1-E-0037;CNLA:1178
LT LAB:NVLAP:200234-0;VCCI: R-1435,C-1440;NEMKO:ELA 113b,113d;BSMI:SL2-IN-E-0013;CNLA:0997

Document Created: 2005-06-08 14:42:56
Document Modified: 2005-06-08 14:42:56

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC