TEST REPORT 5

FCC ID: KBCIX260PNL3BM390

Test Report

Download: PDF
FCCID_490035

Test Report S/N: 100504KBC-T566-E90M Test Date(s): September 03-20, 2004 Test Type: FCC Part 90 EMC Measurements DECLARATION OF COMPLIANCE FCC PART 90 EMC MEASUREMENTS Test Lab Applicant Information CELLTECH LABS INC. ITRONIX CORPORATION Testing and Engineering Services 801 South Stevens Street 1955 Moss Court Spokane, WA 99204 Kelowna, B.C. United States Canada V1Y 9L3 Tel.: 250-448-7047 Fax: 250-448-7046 e-mail: info@celltechlabs.com web site: www.celltechlabs.com FCC IDENTIFIER: KBCIX260PNL3BM390 Model(s): IX260PNL3BM390 FCC Rule Part(s): 47 CFR §90, §2 Test Procedure(s): FCC 47 CFR §90, §2; ANSI TIA/EIA-603-A-2002 Device Classification: Licensed Non-Broadcast Station Transmitter (TNB) Device Description: Rugged Laptop PC with Wavenet BM3-900M Mobitex Radio Modem & Dipole Antenna (co-located with Senao NL-3054MP 802.11b/g WLAN & Internal Dual Surface-Mount Antenna) including (3) Mobile Vehicle-Mount Antennas and Vehicle Cradle Tx Frequency Range: 896.0 - 901.0 MHz Rx Frequency Range: 935.0 - 940.0 MHz Max. ERP Measured: 2.87 Watts (34.58 dBm) - Itronix Swivel Dipole Antenna Model: IX260+ 0.668 Watts (28.25 dBm) - MaxRad Vehicle-Mount Antenna Model: Z563 1.33 Watts (31.25 dBm) - MaxRad Vehicle-Mount Antenna Model: Z567 1.88 Watts (32.74 dBm) - MaxRad Vehicle-Mount Antenna Model: Z573 Max. Conducted Power Tested: 33.2 dBm (2.09 Watts) Max. Duty Cycle Tested: 30 % (Source-Based Time-Averaged) Source-Based Time-Aver. Power: 28.0 dBm (Conducted) Modulation Type: GMSK Emission Designator(s): 12K0F1D Frequency Tolerance(s): ± 0.00015 % Antenna Type(s) Tested: Itronix IX260+ External Swivel Dipole (Mobitex) MaxRad Z563 Vehicle-Mount - Unity Gain (Mobitex) MaxRad Z567 Vehicle-Mount - 5 dBd Gain (Mobitex) MaxRad Z573 Vehicle-Mount - 5 dBd Gain (Mobitex) Power Source(s) Tested: 11.1 V Lithium-ion Battery, 6.0 Ah (Model: A2121-2) 12 V Vehicle Battery (for Vehicle Cradle) This mobile device has demonstrated compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in FCC 47 CFR §90, §2, and ANSI TIA/EIA-603-A-2002. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. This test report shall not be reproduced partially, or in full, without the prior written approval of Celltech Labs Inc. The results and statements contained in this report pertain only to the device(s) evaluated. _____________________ Duane M. Friesen EMC Manager Celltech Labs Inc. © 2004 Celltech Labs Inc. 1 of 17

Test Report S/N: 100504KBC-T566-E90M Test Date(s): September 03-20, 2004 Test Type: FCC Part 90 EMC Measurements TABLE OF CONTENTS Section DESCRIPTION Page # 1.1 SCOPE 3 2.1 GENERAL INFORMATION & DEVICE DESCRIPTION 3 3.1 TEST EQUIPMENT LIST 4 Appendix MEASUREMENT PROCEDURES & DATA FCC Rule Part(s) Page # A RF Output Power §2.1046 5 §90.635 B Effective Radiated Power Output 6-8 §2.1046 §2.1053 C Field Strength of Spurious Radiation 9-13 §90.210j D Radiated Test Setup Photographs 14-17 © 2004 Celltech Labs Inc. 2 of 17

Test Report S/N: 100504KBC-T566-E90M Test Date(s): September 03-20, 2004 Test Type: FCC Part 90 EMC Measurements FCC PART 90 EMC MEASUREMENT REPORT 1.1 SCOPE This report describes the measurements made and results collected during the Electromagnetic emissions testing of the Itronix Corporation IX260+ Rugged Laptop PC incorporating the internal Wavenet BM3-900M Mobitex Radio Modem with external swivel dipole antenna, (3) vehicle-mount antennas, and vehicle cradle. Co-located within the IX260+ Laptop PC is the Senao NL-3054MP 802.11b/g 2.4 GHz DSSS WLAN Mini-PCI Card and RangeStar internal dual surface-mount antenna (co-located transmitters do not transmit simultaneously). The measurement results were applied against the EMC requirements and limits outlined in the technical rules and regulations set forth in the Federal Communication Commission Code of Federal Regulations Title 47 Parts 90, and 2. 2.1 GENERAL INFORMATION / DEVICE DESCRIPTION APPLICANT ITRONIX CORPORATION 801 South Stevens Street, Spokane, WA 99204 FCC IDENTIFIER KBCIX260PNL3BM390 Model(s) IX260PNL3BM390 ZZGEG4196ZZ6470 Production Unit IX260+ Laptop PC Serial No.(s) BM315099WT440 Production Unit Mobitex Radio Modem Rugged Laptop PC with Wavenet BM3-900M Mobitex Radio Modem, Device Type External Swivel Dipole Antenna, (3) Vehicle-Mount Antennas, & Vehicle Cradle Co-located Transmitter(s) Senao NL-3054MP 802.11b/g WLAN with Internal Dual Surface-Mount Antenna Transmit Type Single Transmit Only (Mobitex & WLAN co-located transmitters do not transmit simultaneously) FCC Rule Part(s) 47 CFR §90, §2 FCC Classification Licensed Non-Broadcast Station Transmitter (TNB) Tx Frequency Range 896.0 - 901.0 MHz Rx Frequency Range 935.0 - 940.0 MHz Model Number Type / Description Max. ERP Measured Itronix IX260+ External Swivel Dipole 2.87 W 34.58 dBm Antenna Type(s) Tested MaxRad Z563 Unity Gain Mobile Vehicle-Mount 0.668 W 28.25 dBm MaxRad Z567 5 dBd Gain Mobile Vehicle-Mount 1.33 W 31.25 dBm MaxRad Z573 5 dBd Gain Mobile Vehicle-Mount 1.88 W 32.74 dBm Max. RF Conducted 33.2 dBm Peak Mobitex Max. Source-Based Time-Averaged Conducted Power: 28.0 dBm Peak Output Power Measured Max. Duty Cycle Tested 30 % Source-Based Time-Averaged Emission Designator(s) 12K0F1D Frequency Tolerance ± 0.00015 % Modulation GMSK Lithium-ion Battery 11.1 V, 6.0 Ah Model: A2121-2 Power Source(s) Tested Vehicle Battery 12 V (For Vehicle Cradle) Applicant: Itronix Corporation Model: IX260PNL3BM390 FCC ID: KBCIX260PNL3BM390 Rugged Laptop PC with internal Wavenet BM3-900M Mobitex Radio Modem & WLAN (802.11b/g) 2004 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the written permission of Celltech Labs Inc. 3 of 17

Test Report S/N: 100504KBC-T566-E90M Test Date(s): September 03-20, 2004 Test Type: FCC Part 90 EMC Measurements 3.1 TEST EQUIPMENT LIST Equipment Type Model Serial No. Calibration Due Date HP Signal Generator 8648D (9kHz-4.0GHz) 3847A00611 April 2005 Rohde & Schwarz Signal Generator SMR 20 (10MHz-40GHz) 100104 April 2005 Gigatronics Power Meter 8651A 8650137 April 2005 Gigatronics Power Meter 8652A 1835267 April 2005 Gigatronics Power Sensor 80701A (0.05-18GHz) 1833535 April 2005 Gigatronics Power Sensor 80701A (0.05-18GHz) 1833542 April 2005 Gigatronics Power Sensor 80701A (0.05-18GHz) 1834350 April 2005 Amplifier Research Power Amp. 5S1G4 (5W, 800MHz-4.2GHz) 26235 N/A Amplifier Research Power Amp. 10W1000C (0.5 – 1 GHz) 27887 N/A Microwave System Amplifier HP 83017A (0.5-26.5GHz) 3123A00587 N/A Network Analyzer HP 8753E (30kHz-3GHz) US38433013 April 2005 Frequency Counter HP 53181A (3GHz) 3736A05175 April 2005 DC Power Supply HP E3611A KR83015294 N/A Multi-Device Controller EMCO 2090 9912-1484 N/A Mini Mast EMCO 2075 0001-2277 N/A Turntable EMCO 2080-1.2/1.5 0002-1002 N/A ETS 3115 (1-18GHz) Double Ridged Horn Antenna 6267 Oct 2004 TX Substitution Antenna (Horn SN6267) Double Ridged Horn Antenna ETS 3115 (1-18GHz) 6276 Oct 2004 ETS 3160-09 Standard Gain Horn Antenna 9810-1123 N/A TX Substitution Antenna (3160-09) Standard Gain Horn Antenna ETS 3160-09 1263 N/A Bilog Antenna Schaffner CBL6111A 1607 Jan 2005 3121C-DB4 Roberts Dipole Antenna 0003-1494 Dec 2004 TX Substitution Antenna (B_3121C) Roberts Dipole Antenna 3121C-DB4 0003-1498 Dec 2004 Spectrum Analyzer HP 8594E 3543A02721 April 2005 Spectrum Analyzer HP E4408B US39240170 Dec 2004 Shielded Screen Room Lindgren R.F. 18W-2/2-0 16297 N/A Environmental Chamber ESPEC ECT-2 (Temperature/Humidity) 0510154-B Feb 2005 Directional Coupler Amplifier Research DC7154 (0.8-4.2 GHz) 26197 N/A Directional Coupler Pasternack PE2214-20 00078 N/A High Pass Filter Microwave Circuits HIG318G1 0001DC0020 N/A High Pass Filter Microwave Circuits H02G18G1 0001DC0020 N/A 30 dB Attenuator Pasternack PE7019-30 00065 N/A Applicant: Itronix Corporation Model: IX260PNL3BM390 FCC ID: KBCIX260PNL3BM390 Rugged Laptop PC with internal Wavenet BM3-900M Mobitex Radio Modem & WLAN (802.11b/g) 2004 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the written permission of Celltech Labs Inc. 4 of 17

Test Report S/N: 100504KBC-T566-E90M Test Date(s): September 03-20, 2004 Test Type: FCC Part 90 EMC Measurements APPENDIX A - RF OUTPUT POWER MEASUREMENT - §2.1046 A.1. MEASUREMENT PROCEDURE The peak conducted power levels were measured at the Wavenet BM3-900M Mobitex radio modem RF port with a Gigatronics 8652A Universal Power Meter in burst average power mode. An offset was entered into the power meter to correct for the losses of the attenuator and cable installed before the sensor input. The transmitter terminal was coupled to the power meter and the DUT was placed in test mode using the Wavenet BM3-900M Mobitex test software installed in the IX260+ Laptop PC with the internal transmitter in modulated carrier mode (30% duty cycle) at a full rated power. All subsequent tests were performed using the same power measurement procedures. A.2. MEASUREMENT DATA Conducted Power Measurements Frequency Peak Power (MHz) (dBm) 896.0 33.2 901.0 33.2 Applicant: Itronix Corporation Model: IX260PNL3BM390 FCC ID: KBCIX260PNL3BM390 Rugged Laptop PC with internal Wavenet BM3-900M Mobitex Radio Modem & WLAN (802.11b/g) 2004 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the written permission of Celltech Labs Inc. 5 of 17

Test Report S/N: 100504KBC-T566-E90M Test Date(s): September 03-20, 2004 Test Type: FCC Part 90 EMC Measurements APPENDIX B - EFFECTIVE RADIATED POWER OUTPUT - §90.635; §2.1046 B.1. MEASUREMENT PROCEDURE ERP measurements were performed using the Signal Substitution Method in accordance with ANSI TIA/EIA-603-A-2002 on a 3-meter open area test site. The DUT was placed in test mode using the Wavenet BM3-900M Mobitex test software installed in the IX260+ Laptop PC with the internal transmitter in modulated carrier mode (30% duty cycle) at a full rated power. The DUT was placed on a turntable 3 meters from the receive antenna. For the swivel dipole evaluation, the DUT was placed on a Styrofoam support at the center of the turntable, 1 meter above the ground plane. For the vehicle-mount antenna evaluations, the antenna was fixed on a 50 cm x 50 cm ground plane on a Styrofoam support placed on a wooden table, at a distance of 3 meters from the biconilog receive antenna, and connected to the vehicle cradle via a 17-foot LMR-195 cable representing a typical vehicle-mount installation. The IX260+ Laptop PC was installed in the vehicle cradle and placed on the wooden table. The maximum field intensity was determined by rotating the DUT approximately 360 degrees and changing the height of the biconilog receive antenna from 1 to 4 meters. Once the maximum emission was found, the spectrum analyzer was set to peak hold and the uncorrected emission value recorded for each of the low, mid and high channels tested. The DUT was then substituted with a dipole antenna. A signal, simulating the DUT emission was generated, amplified, and fed through a directional coupler to the substitution antenna. The height and direction of the receive antenna as well as the direction of the substitution dipole was adjusted for a maximum received signal. The power applied to the dipole was then adjusted to give the same field strength reading as previously recorded for the DUT and the power at the forward coupler port recorded. The substitution antenna was then replaced with a calibrated power sensor, the forward coupler port power level confirmed and the power applied to the dipole antenna recorded. The ERP level was determined by correcting the applied feed point power with the addition of the dipole gain. (See next pages for measurement data) B.2. MEASUREMENT SETUP Spectrum Analyzer 3 Meters Device Under Test Turntable 1 Meter Figure 2. Radiated Power Measurement Test Setup Diagram Applicant: Itronix Corporation Model: IX260PNL3BM390 FCC ID: KBCIX260PNL3BM390 Rugged Laptop PC with internal Wavenet BM3-900M Mobitex Radio Modem & WLAN (802.11b/g) 2004 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the written permission of Celltech Labs Inc. 6 of 17

Test Report S/N: 100504KBC-T566-E90M Test Date(s): September 03-20, 2004 Test Type: FCC Part 90 EMC Measurements EFFECTIVE RADIATED POWER OUTPUT - §90.635; §2.1046 (Continued) B.3. MEASUREMENT DATA Applicant: Itronix Corporation Model: IX260PNL3BM390 FCC ID: KBCIX260PNL3BM390 Rugged Laptop PC with internal Wavenet BM3-900M Mobitex Radio Modem & WLAN (802.11b/g) 2004 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the written permission of Celltech Labs Inc. 7 of 17

Test Report S/N: 100504KBC-T566-E90M Test Date(s): September 03-20, 2004 Test Type: FCC Part 90 EMC Measurements EFFECTIVE RADIATED POWER OUTPUT - §90.635; §2.1046 (Continued) B.3. MEASUREMENT DATA (Cont.) Applicant: Itronix Corporation Model: IX260PNL3BM390 FCC ID: KBCIX260PNL3BM390 Rugged Laptop PC with internal Wavenet BM3-900M Mobitex Radio Modem & WLAN (802.11b/g) 2004 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the written permission of Celltech Labs Inc. 8 of 17

Test Report S/N: 100504KBC-T566-E90M Test Date(s): September 03-20, 2004 Test Type: FCC Part 90 EMC Measurements APPENDIX C - FIELD STRENGTH OF SPURIOUS RADIATION - §90.210j; §2.1053 C.1. MEASUREMENT PROCEDURE Radiated spurious emissions were measured on a 3-meter open area test site using the Signal Substitution Method in accordance with ANSI TIA/EIA-603-A-2002. The DUT was placed in the vehicle cradle and programmed in test mode using the Wavenet BM3-900M Mobitex test software installed in the IX260+ Laptop PC with the internal transmitter in modulated carrier mode (30% duty cycle) at a full rated power. For the swivel dipole evaluation, the DUT was placed on a Styrofoam support at the center of the turntable, 1 meter above the ground plane. For the vehicle-mount antenna evaluations, the antenna was fixed on a 50 cm x 50 cm ground plane on a Styrofoam support placed on a wooden table, at a distance of 3 meters from the receive antenna, and connected to the vehicle cradle via a 17-foot LMR-195 cable representing a typical vehicle-mount installation. The IX260+ Laptop PC was installed in the vehicle cradle and placed on the wooden table. A frequency band from just above the highest transmitted frequency to just above the 10th harmonic of the highest transmitted frequency was divided into smaller bands corresponding to measurement equipment setups and capabilities. The measurement equipment including carrier blocking filters, was optimized for maximum sensitivity for each band while ensuring no saturation occurred in any gain stages that may be present. The maximum field intensity in each of these bands were determined by rotating the DUT approximately 360 degrees and changing the height of the receive antenna from 1 to 4 meters while maintaining the spectrum analyzer trace in max hold. The stored trace was then evaluated to determine any significant emissions that should be evaluated by substitution. The frequency and uncorrected field strength level for each significant emission was recorded. To describe the noise floor, the maximum level associated with a number of frequencies within the band were also recorded. The DUT was then substituted with a transmit antenna. A signal simulating the DUT emission was generated for each of the signals recorded; it was amplified and fed through a directional coupler to the substitution antenna. The height and direction of the receive antenna as well as the direction of the substitution horn was adjusted for a maximum received signal. The power applied to the transmit antenna was then adjusted to give the same field strength reading as previously recorded for the DUT and the power at the forward coupler port recorded. The substitution antenna was then replaced with a calibrated power sensor, the forward coupler port power level confirmed and the power applied to the horn antenna recorded. The radiated power level was determined by correcting the applied feed point power with the addition of the antenna gain. (See next pages for measurement data) C.2. MEASUREMENT SETUP Spectrum Analyzer 3 Meters 1 Meter or 3 Meters Device Under Test Turntable 1 Meter Figure 3. Radiated Spurious Measurement Test Setup Diagram (3 Meters for Frequencies < 10 GHz - 1 Meter for Frequencies > 10 GHz) Applicant: Itronix Corporation Model: IX260PNL3BM390 FCC ID: KBCIX260PNL3BM390 Rugged Laptop PC with internal Wavenet BM3-900M Mobitex Radio Modem & WLAN (802.11b/g) 2004 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the written permission of Celltech Labs Inc. 9 of 17

Test Report S/N: 100504KBC-T566-E90M Test Date(s): September 03-20, 2004 Test Type: FCC Part 90 EMC Measurements FIELD STRENGTH OF SPURIOUS RADIATION - §90.210j; §2.1053 (Continued) C.3. MEASUREMENT DATA Applicant: Itronix Corporation Model: IX260PNL3BM390 FCC ID: KBCIX260PNL3BM390 Rugged Laptop PC with internal Wavenet BM3-900M Mobitex Radio Modem & WLAN (802.11b/g) 2004 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the written permission of Celltech Labs Inc. 10 of 17

Test Report S/N: 100504KBC-T566-E90M Test Date(s): September 03-20, 2004 Test Type: FCC Part 90 EMC Measurements FIELD STRENGTH OF SPURIOUS RADIATION - §90.210j; §2.1053 (Continued) C.3. MEASUREMENT DATA (Cont.) Applicant: Itronix Corporation Model: IX260PNL3BM390 FCC ID: KBCIX260PNL3BM390 Rugged Laptop PC with internal Wavenet BM3-900M Mobitex Radio Modem & WLAN (802.11b/g) 2004 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the written permission of Celltech Labs Inc. 11 of 17

Test Report S/N: 100504KBC-T566-E90M Test Date(s): September 03-20, 2004 Test Type: FCC Part 90 EMC Measurements FIELD STRENGTH OF SPURIOUS RADIATION - §90.210j; §2.1053 (Continued) C.3. MEASUREMENT DATA (Cont.) Applicant: Itronix Corporation Model: IX260PNL3BM390 FCC ID: KBCIX260PNL3BM390 Rugged Laptop PC with internal Wavenet BM3-900M Mobitex Radio Modem & WLAN (802.11b/g) 2004 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the written permission of Celltech Labs Inc. 12 of 17

Test Report S/N: 100504KBC-T566-E90M Test Date(s): September 03-20, 2004 Test Type: FCC Part 90 EMC Measurements FIELD STRENGTH OF SPURIOUS RADIATION - §90.210j; §2.1053 (Continued) C.3. MEASUREMENT DATA (Cont.) Applicant: Itronix Corporation Model: IX260PNL3BM390 FCC ID: KBCIX260PNL3BM390 Rugged Laptop PC with internal Wavenet BM3-900M Mobitex Radio Modem & WLAN (802.11b/g) 2004 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the written permission of Celltech Labs Inc. 13 of 17


Document Created: 2004-11-17 17:15:49
Document Modified: 2004-11-17 17:15:49
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC