SAR report part 4

FCC ID: KBCIX-4965AGN

RF Exposure Info

Download: PDF
FCCID_931064

Date(s) of Evaluation Test Report Serial No. Test Report Revision No. November 02, 06, 2007 102407KBC-T866-S15WB Rev. 1.0 (Initial Release) Test Report Issue Date Description of Test(s) RF Exposure Category March 20, 2008 Specific Absorption Rate General Population Certificate No. 2470.01 APPENDIX F - SYSTEM VALIDATION Company: General Dynamics Itronix Corporation FCC ID: KBCIX-4965AGN IC: 1943A-4965AGN Model(s): IX350 DUT Type: Tablet PC with 802.11a/b/g/n WLAN & Co-located Bluetooth 2008 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 70 of 72

Date of Evaluation: June 08, 2007 Document Serial No.: SV2450M-060807-R1.4 Evaluation Type: System Validation Validation Dipole: 2450 MHz Fluid Type: Body 2450 MHz SYSTEM VALIDATION Type: 2450 MHz Validation Dipole Asset Number: 00025 Serial Number: 150 Place of Validation: Celltech Labs Inc. Date of Validation: June 08, 2007 Celltech Labs Inc. certifies that the 2450 MHz System Validation was performed on the date indicated above. Performed by: Cheri Frangiadakis Approved by: Sean Johnston Celltech Labs Inc. 21-364 Lougheed Rd., Kelowna, B.C. V1X 7R8 Canada Tel. 250-765-7650 x Fax. 250-765-7645 x e-mail: info@celltechlabs.com www.celltechlabs.com 2007 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 1 of 11

Date of Evaluation: June 08, 2007 Document Serial No.: SV2450M-060807-R1.4 Evaluation Type: System Validation Validation Dipole: 2450 MHz Fluid Type: Body 1. Dipole Construction & Electrical Characteristics The validation dipole was constructed in accordance with the requirements specified in IEEE Standard 1528- 2003 and International Standard IEC 62209-1:2005. The electrical properties were measured using an HP 8753ET Network Analyzer. The network analyzer was calibrated to the validation dipole N-type connector feed point using an HP85032E Type N calibration kit. The dipole was placed parallel to a planar phantom at a separation distance of 10.0mm from the simulating fluid using a loss-less dielectric spacer. The measured input impedance is: Feed point impedance at 2450 MHz Re{Z} = 45.100: Im{Z} = 3.5605: Return Loss at 2450 MHz -23.411dB Reference dipole - basic mechanical parameters 2007 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 2 of 11

a Jun zear egrase2s En3 rrl Loo 10 aormer o se arm2sea ap 2 «s0.000 cce mz § ESX ~— r—_ |_._—4 L4 céiimcr 2 45a.500 soe hiz sFai a60.000 se wis 8 Jun 207. @B:39:54 Emm rrl a ucrs is 48100 a a.sses a_zonge pi 2 «s0.000 ooo nz + tor + ceiter 2 «s0.o00 ons Mz sran «a0.a00 on it esces caus n inuoourremie ux o ue reprouui i wntore n in par wiouie prin wintent prvinimwin or verien taus n rage o on i1

Date of Evaluation: June 08, 2007 Document Serial No.: SV2450M-060807-R1.4 Evaluation Type: System Validation Validation Dipole: 2450 MHz Fluid Type: Body 3. Validation Dipole Dimensions Frequency (MHz) L (mm) H (mm) D (mm) 300 396.0 250.0 6.0 450 270.0 167.0 6.0 835 161.0 89.8 3.6 900 149.0 83.3 3.6 1450 89.1 51.7 3.6 1800 72.0 41.7 3.6 1900 68.0 39.5 3.6 2000 64.5 37.5 3.6 2450 51.5 30.4 3.6 3000 41.5 25.0 3.6 4. Validation Phantom The validation phantom is the SAM (Specific Anthropomorphic Mannequin) phantom manufactured by Schmid & Partner Engineering AG. The SAM phantom is a Fiberglass shell integrated in a wooden table. The shape of the shell corresponds to the phantom defined by SCC34-SC2. It enables the dosimetric evaluation of left and right hand phone usage as well as body mounted usage at the flat phantom region. A cover prevents evaporation of the liquid. Reference markings on the phantom allow the complete setup of all predefined phantom positions and measurement grids by manually teaching three points in the robot. Shell Thickness: 2.0 ± 0.1 mm Filling Volume: Approx. 25 liters Dimensions: 50 cm (W) x 100 cm (L) SAM Phantom Fluid Depth (t 15.0 cm) 2007 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 4 of 11


(Celltech raye o o

Date of Evaluation: June 08, 2007 Document Serial No.: SV2450M-060807-R1.4 Evaluation Type: System Validation Validation Dipole: 2450 MHz Fluid Type: Body 7. SAR Measurement Measurements were made at the planar section of the SAM phantom using a dosimetric E-field probe EX3DV4 (S/N: 3600, conversion factor 6.31). The SAR measurement was performed with the E-field probe in mechanical detection mode only. The setup and determination of the forward power into the dipole was performed using the procedures described below. First the power meter PM1 (including attenuator Att1) is connected to the cable to measure the forward power at the location of the dipole connector (X). The signal generator is adjusted for the desired forward power at the dipole connector (taking into account the attenuation of Att1) as read by power meter PM2. After connecting the cable to the dipole, the signal generator is readjusted for the same reading at power meter PM2. If the signal generator does not allow adjustment in 0.01dB steps, the remaining difference at PM2 must be taken into consideration. PM3 records the reflected power from the dipole to ensure that the value is not changed from the previous value. The reflected power should be 20dB below the forward power. 3D Probe positioner d Field probe Flat Phantom Dipole Dir.Coupler Signal Amp Low 3dB x Generator Pass Cable Att1 Att3 PM1 Att2 PM3 PM2 System Validation Measurement Setup Diagram 2007 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 7 of 11

Date of Evaluation: June 08, 2007 Document Serial No.: SV2450M-060807-R1.4 Evaluation Type: System Validation Validation Dipole: 2450 MHz Fluid Type: Body 8. Measurement Conditions The SAM phantom was filled with 2450 MHz Body tissue simulant. Relative Permittivity: 50.1 (-4.9% deviation from target) Conductivity: 1.99 mho/m (+2.1% deviation from target) Fluid Temperature: 21.5 qC (Start of Test) / 21.2 qC (End of Test) Fluid Depth: t 15.0 cm Environmental Conditions: Ambient Temperature: 22.7 qC Barometric Pressure: 101.1 kPa Humidity: 31 % The 2450 MHz Body tissue simulant consisted of the following ingredients: Ingredient Percentage by weight Water 69.98% Glycol Monobutyl 30.00% Salt 0.02% IEEE Target Dielectric Parameters: Hr = 52.7 (+/-5%) V = 1.95 S/m (+/-5%) 9. System Validation SAR Results SAR @ 0.25W Input averaged over 1g (W/kg) SAR @ 1W Input averaged over 1g (W/kg) SPEAG Target Measured Deviation SPEAG Target Measured Deviation 12.8 +/- 10% 13.4 +4.7% 51.2 +/- 10% 53.6 +4.7% SAR @ 0.25W Input averaged over 10g (W/kg) SAR @ 1W Input averaged over 10g (W/kg) SPEAG Target Measured Deviation SPEAG Target Measured Deviation 5.93 +/- 10% 6.03 +1.7% 23.7 +/- 10% 24.1 +1.7% 2007 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 8 of 11

Date of Evaluation: June 08, 2007 Document Serial No.: SV2450M-060807-R1.4 Evaluation Type: System Validation Validation Dipole: 2450 MHz Fluid Type: Body System Validation - 2450 MHz Dipole - June 8, 2007 DUT: Dipole 2450 MHz; Asset: 00025; Serial: 150 Ambient Temp: 22.7qC; Fluid Temp: 21.5qC; Barometric Pressure: 101.1 kPa; Humidity: 31% Communication System: CW Forward Conducted Power: 250 mW Frequency: 2450 MHz; Duty Cycle: 1:1 3 Medium: M2450 Medium parameters used: f = 2450 MHz; ı = 1.99 mho/m; İr = 50.1; ȡ = 1000 kg/m - Probe: EX3DV4 - SN3600; ConvF(6.31, 6.31, 6.31); Calibrated: 24/01/2007 - Sensor-Surface: 2 mm (Mechanical Surface Detection) - Electronics: DAE4 Sn353; Calibrated: 21/06/2006 - Phantom: SAM 4.0; Type: Fiberglas; Serial: 1033 - Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 2450 MHz System Validation/Area Scan (6x10x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = 13.1 mW/g 2450 MHz System Validation/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 91.9 V/m; Power Drift = -0.128 dB Peak SAR (extrapolated) = 28.6 W/kg SAR(1 g) = 13.4 mW/g; SAR(10 g) = 6.03 mW/g Maximum value of SAR (measured) = 15.5 mW/g  2007 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 9 of 11

Date of Evaluation: June 08, 2007 Document Serial No.: SV2450M-060807-R1.4 Evaluation Type: System Validation Validation Dipole: 2450 MHz Fluid Type: Body 10. Measured Fluid Dielectric Parameters System Validation - 2450 MHz (Body) ************************************************************ Celltech Labs Inc. Test Result for UIM Dielectric Parameter Fri 08/Jun/2007 Frequency (GHz) FCC_eH FCC Bulletin 65 Supplement C (June 2001) Limits for Head Epsilon FCC_sH FCC Bulletin 65 Supplement C (June 2001) Limits for Head Sigma FCC_eB FCC Limits for Body Epsilon FCC_sB FCC Limits for Body Sigma Test_e Epsilon of UIM Test_s Sigma of UIM ************************************************************ Freq FCC_eB FCC_sB Test_e Test_s 2.3500 52.83 1.85 50.39 1.89 2.3600 52.82 1.86 50.32 1.90 2.3700 52.81 1.87 50.28 1.91 2.3800 52.79 1.88 50.28 1.93 2.3900 52.78 1.89 50.31 1.94 2.4000 52.77 1.90 50.26 1.95 2.4100 52.75 1.91 50.24 1.96 2.4200 52.74 1.92 50.21 1.96 2.4300 52.73 1.93 50.21 1.98 2.4400 52.71 1.94 50.13 1.99 2.4500 52.70 1.95 50.09 1.99 2.4600 52.69 1.96 50.01 2.03 2.4700 52.67 1.98 50.10 2.03 2.4800 52.66 1.99 50.12 2.05 2.4900 52.65 2.01 50.09 2.07 2.5000 52.64 2.02 50.08 2.07 2.5100 52.62 2.04 50.03 2.08 2.5200 52.61 2.05 50.02 2.09 2.5300 52.60 2.06 49.93 2.10 2.5400 52.59 2.08 49.87 2.11 2.5500 52.57 2.09 49.78 2.13 2007 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 10 of 11

Date of Evaluation: June 08, 2007 Document Serial No.: SV2450M-060807-R1.4 Evaluation Type: System Validation Validation Dipole: 2450 MHz Fluid Type: Body 11. Measurement Uncertainties UNCERTAINTY BUDGET FOR SYSTEM VALIDATION Uncertainty Uncertainty Probability ci Error Description Value Divisor Value Vi or Veff Distribution 1g ±% ±% (1g) Measurement System Probe calibration (2450 MHz) 5.9 Normal 1 1 5.9 f Axial isotropy of the probe 4.7 Rectangular 1.732050808 1 2.7 f Spherical isotropy of the probe 0 Rectangular 1.732050808 1 0.0 f Spatial resolution 0 Rectangular 1.732050808 1 0.0 f Boundary effects 0.2 Rectangular 1.732050808 1 0.1 f Probe linearity 4.7 Rectangular 1.732050808 1 2.7 f Detection limit 1 Rectangular 1.732050808 1 0.6 f Readout electronics 0.3 Normal 1 1 0.3 f Response time 0 Rectangular 1.732050808 1 0.0 f Integration time 0 Rectangular 1.732050808 1 0.0 f RF ambient conditions 3 Rectangular 1.732050808 1 1.7 f Mech. constraints of robot 0.4 Rectangular 1.732050808 1 0.2 f Probe positioning 2.9 Rectangular 1.732050808 1 1.7 f Extrapolation & integration 1 Rectangular 1.732050808 1 0.6 f Dipole Dipole Positioning 2 Normal 1.732050808 1 1.2 f Power & Power Drift 4.7 Normal 1.732050808 1 2.7 f Phantom and Setup Phantom uncertainty 4 Rectangular 1.732050808 1 2.3 f Liquid conductivity (target) 5 Rectangular 1.732050808 0.64 1.8 f Liquid conductivity (measured) 2.1 Normal 1 0.64 1.3 f Liquid permittivity (target) 5 Rectangular 1.732050808 0.6 1.7 f Liquid permittivity (measured) 4.9 Normal 1 0.6 2.9 f Combined Standard Uncertainty 9.33 Expanded Uncertainty (k=2) 18.66 Measurement Uncertainty Table in accordance with IEEE Standard 1528-2003 and IEC Standard 62209-1:2005 12. Test Equipment List TEST EQUIPMENT ASSET NO. SERIAL NO. DATE OF CAL. CAL. DUE DATE SPEAG DASY4 Measurement Server 00158 1078 N/A N/A SPEAG Robot 00046 599396-01 N/A N/A SPEAG DAE4 00019 353 21Jun06 21Jun07 SPEAG EX3DV4 E-Field Probe 00213 3600 24Jan07 24Jan08 2450 MHz Validation Dipole 00025 150 08Jun07 08Jun08 SPEAG SAM Phantom V4.0C 00154 1033 N/A N/A ALS-PR-DIEL Dielectric Probe Kit 00160 260-00953 N/A N/A Gigatronics 8652A Power Meter 00007 1835272 26Mar07 26Mar08 Gigatronics 80701A Power Sensor 00014 1833699 22Jan07 22Jan08 Gigatronics 80701A Power Sensor 00109 1834366 26Mar07 26Mar08 HP 8753ET Network Analyzer 00134 US39170292 20Apr07 20Apr08 HP 8648D Signal Generator 00005 3847A00611 NCR NCR Amplifier Research 5S1G4 Power Amplifier 00106 26235 NCR NCR 2007 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 11 of 11

Date of Evaluation: May 18, 2007 Document Serial No.: SV5200M-051807-R1.2 Evaluation Type: System Validation Validation Dipole: 5200 MHz Fluid Type: Body 5200 MHz SYSTEM VALIDATION Type: 5200 MHz Validation Dipole Asset Number: 00126 Serial Number: 1031 Place of Validation: Celltech Labs Inc. Date of Validation: May 18, 2007 Celltech Labs Inc. certifies that the 5200 MHz System Validation was performed on the date indicated above. Performed by: Cheri Frangiadakis Approved by: Sean Johnston Celltech Labs Inc. 21-364 Lougheed Rd., Kelowna, B.C. V1X 7R8 Canada Tel. 250-765-7650 x Fax. 250-765-7645 x e-mail: info@celltechlabs.com www.celltechlabs.com 2007 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 1 of 11

Date of Evaluation: May 18, 2007 Document Serial No.: SV5200M-051807-R1.2 Evaluation Type: System Validation Validation Dipole: 5200 MHz Fluid Type: Body 1. Dipole Construction & Electrical Characteristics The validation dipole was manufactured by Schmid and Partner Engineering AG. The electrical properties were measured using an HP 8753ET Network Analyzer. The network analyzer was calibrated to the validation dipole N-type connector feed point using an HP85032E Type N calibration kit. The dipole was placed parallel to a planar phantom at a separation distance of 10.0mm from the simulating fluid using a loss-less dielectric spacer. The measured input impedance is: Feed point impedance at 5200 MHz Re{Z} = 50.324: Im{Z} = 3.5215: Return Loss at 5200 MHz -28.311 dB Reference dipole - basic mechanical parameters 2007 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 2 of 11

a8 nay 2eo7. oorsorar EBM er. oo 10 corser o an —21.264 ds s nemeos coe iz + CHL Nankers Sn 22,509 oo t 5.8 GHz Sedaa ue ~2a.0uon Szeden onz tys 18 & L__] £2=1" fv“?/\ 4 Staey 1 500.000 one is stor © con.e0e aoe mis 18 may 2007 eoranss hn enc a ucrs asasose somes saraepd s see,c00 cee nz * chit narkers &s sueer a —rdoar a & s.sdbon tz fvs is & centcr s 50.000 c00 nz spou 1 006.c00 006 miz

Date of Evaluation: May 18, 2007 Document Serial No.: SV5200M-051807-R1.2 Evaluation Type: System Validation Validation Dipole: 5200 MHz Fluid Type: Body 3. Validation Dipole Dimensions Frequency (MHz) L (mm) H (mm) D (mm) 300 396.0 250.0 6.0 450 270.0 167.0 6.0 835 161.0 89.8 3.6 900 149.0 83.3 3.6 1450 89.1 51.7 3.6 1800 72.0 41.7 3.6 1900 68.0 39.5 3.6 2000 64.5 37.5 3.6 2450 51.5 30.4 3.6 3000 41.5 25.0 3.6 5200 - 5800 20.6 40.65 3.6 4. Validation Phantom The validation phantom is the SAM (Specific Anthropomorphic Mannequin) phantom manufactured by Schmid & Partner Engineering AG. The SAM phantom is a Fiberglass shell integrated in a wooden table. The shape of the shell corresponds to the phantom defined by SCC34-SC2. It enables the dosimetric evaluation of left and right hand phone usage as well as body mounted usage at the flat phantom region. A cover prevents evaporation of the liquid. Reference markings on the phantom allow the complete setup of all predefined phantom positions and measurement grids by manually teaching three points in the robot. Shell Thickness: 2.0 ± 0.1 mm Filling Volume: Approx. 25 liters Dimensions: 50 cm (W) x 100 cm (L) SAM Phantom Fluid Depth (t 15.0 cm) 2007 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 4 of 11

(‘Celltech


Date of Evaluation: May 18, 2007 Document Serial No.: SV5200M-051807-R1.2 Evaluation Type: System Validation Validation Dipole: 5200 MHz Fluid Type: Body 7. SAR Measurement Measurements were made using a dosimetric E-field probe EX3DV4 (S/N: 3600, Conversion Factor 4.10). The SAR measurement was performed with the E-field probe in mechanical detection mode only. The setup and determination of the forward power into the dipole was performed using the procedures described below. First the power meter PM1 (including attenuator Att1) is connected to the cable to measure the forward power at the location of the dipole connector (X). The signal generator is adjusted for the desired forward power at the dipole connector (taking into account the attenuation of Att1) as read by power meter PM2. After connecting the cable to the dipole, the signal generator is readjusted for the same reading at power meter PM2. If the signal generator does not allow adjustment in 0.01dB steps, the remaining difference at PM2 must be taken into consideration. PM3 records the reflected power from the dipole to ensure that the value is not changed from the previous value. The reflected power should be 20dB below the forward power. 3D Probe positioner d Field probe Flat Phantom Dipole Dir.Coupler Signal Amp Low 3dB x Generator Pass Cable Att1 Att3 PM1 Att2 PM3 PM2 System Validation Measurement Setup Diagram 2007 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 7 of 11

Date of Evaluation: May 18, 2007 Document Serial No.: SV5200M-051807-R1.2 Evaluation Type: System Validation Validation Dipole: 5200 MHz Fluid Type: Body 8. Measurement Conditions The SAM phantom was filled with 5200 MHz Body tissue simulant. Relative Permittivity: 44.6 (-9.0% deviation from target) Conductivity: 5.52 mho/m (+4.2% deviation from target) Fluid Temperature: 23.6 qC (Start of Test) / 23.7 qC (End of Test) Fluid Depth: t 15.0 cm Environmental Conditions: Ambient Temperature: 25.0qC Humidity: 48% Barometric Pressure: 101.1 kPa The 5200 MHz Body tissue simulant consisted of the following ingredients: Ingredient Percentage by weight Water 64 - 78% Mineral Oil 11 - 18% Emulsifiers 9 - 15% Additives and Salt 2 - 3% IEEE Target Dielectric Parameters: Hr = 49.0 (+/-10%) V = 5.30 S/m (+/-5%) 9. System Validation SAR Results SAR @ 0.25W Input averaged over 1g (W/kg) SAR @ 1W Input averaged over 1g (W/kg) SPEAG Target Measured Deviation SPEAG Target Measured Deviation 18.0 +/- 10% 18.2 +1.2% 72.0 +/- 10% 72.8 +1.1% SAR @ 0.25W Input averaged over 10g (W/kg) SAR @ 1W Input averaged over 10g (W/kg) SPEAG Target Measured Deviation SPEAG Target Measured Deviation 5.03 +/- 10% 5.12 +1.8% 20.12 +/- 10% 20.48 +1.8% Extrapolated Peak SAR SPEAG Target 71.2 +/- 15% Measured 72.7 +2.1% 2007 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 8 of 11

Date of Evaluation: May 18, 2007 Document Serial No.: SV5200M-051807-R1.2 Evaluation Type: System Validation Validation Dipole: 5200 MHz Fluid Type: Body System Validation - 5200 MHz Dipole - May 18, 2007 DUT: Dipole 5GHz; Model: D5GHzV2; Asset: 00126; Serial: 1031 Ambient Temp: 25.0ºC; Fluid Temp: 23.6ºC; Barometric Pressure: 101.1 kPa; Humidity: 48% Communication System: CW Forward Conducted Power: 250mW Frequency: 5200 MHz; Duty Cycle: 1:1 3 Medium: M5200-5800 Medium parameters used: f = 5200 MHz; ı = 5.52 mho/m; İr = 44.6; ȡ = 1000 kg/m - Probe: EX3DV4 - SN3600; ConvF(4.1, 4.1, 4.1); Calibrated: 24/01/2007 - Sensor-Surface: 2 mm (Mechanical Surface Detection) - Electronics: DAE4 Sn353; Calibrated: 21/06/2006 - Phantom: SAM 4.0; Type: Fiberglas; Serial: 1033 - Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 5200 MHz System Validation/Area Scan (9x13x1): Measurement grid: dx=5mm, dy=5mm Maximum value of SAR (measured) = 48.3 mW/g 5200 MHz System Validation/Zoom Scan (7x7x9)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=2.5mm Reference Value = 86.3 V/m; Power Drift = 0.100 dB Peak SAR (extrapolated) = 72.7 W/kg SAR(1 g) = 18.2 mW/g; SAR(10 g) = 5.12 mW/g Maximum value of SAR (measured) = 36.1 mW/g  2007 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 9 of 11

Date of Evaluation: May 18, 2007 Document Serial No.: SV5200M-051807-R1.2 Evaluation Type: System Validation Validation Dipole: 5200 MHz Fluid Type: Body 10. Measured Fluid Dielectric Parameters System Validation - 5200 MHz (Body) ************************************************************ Celltech Labs Inc. Test Result for UIM Dielectric Parameter Tue 18/May/2007 Frequency (GHz) FCC_eH FCC Bulletin 65 Supplement C (June 2001) Limits for Head Epsilon FCC_sH FCC Bulletin 65 Supplement C (June 2001) Limits for Head Sigma FCC_eB FCC Limits for Body Epsilon FCC_sB FCC Limits for Body Sigma Test_e Epsilon of UIM Test_s Sigma of UIM ************************************************************ Freq FCC_eB FCC_sB Test_e Test_s 5.1000 49.15 5.18 44.46 5.40 5.1100 49.14 5.19 44.42 5.39 5.1200 49.12 5.21 44.40 5.36 5.1300 49.11 5.22 44.40 5.40 5.1400 49.10 5.23 44.38 5.39 5.1500 49.08 5.24 44.37 5.38 5.1600 49.07 5.25 44.46 5.44 5.1700 49.06 5.26 44.35 5.46 5.1800 49.04 5.28 44.31 5.47 5.1900 49.03 5.29 44.38 5.51 5.2000 49.01 5.30 44.55 5.52 5.2100 49.00 5.31 44.40 5.53 5.2200 48.99 5.32 44.23 5.48 5.2300 48.97 5.33 44.20 5.51 5.2400 48.96 5.35 44.14 5.54 5.2500 48.95 5.36 44.15 5.58 5.2600 48.93 5.37 44.19 5.56 5.2700 48.92 5.38 44.16 5.57 5.2800 48.91 5.39 44.01 5.59 5.2900 48.89 5.40 44.00 5.62 5.3000 48.88 5.42 43.98 5.63 2007 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 10 of 11

Date of Evaluation: May 18, 2007 Document Serial No.: SV5200M-051807-R1.2 Evaluation Type: System Validation Validation Dipole: 5200 MHz Fluid Type: Body 11. Measurement Uncertainties UNCERTAINTY BUDGET FOR SYSTEM VALIDATION Uncertainty Uncertainty Probability ci Error Description Value Divisor Value Vi or Veff Distribution 1g ±% ±% (1g) Measurement System Probe calibration (5200 MHz) 6.55 Normal 1 1 6.55 f Axial isotropy of the probe 4.7 Rectangular 1.732050808 1 2.7 f Spherical isotropy of the probe 9.6 Rectangular 1.732050808 1 5.5 f Spatial resolution 0 Rectangular 1.732050808 1 0.0 f Boundary effects 0.1 Rectangular 1.732050808 1 0.1 f Probe linearity 4.7 Rectangular 1.732050808 1 2.7 f Detection limit 1 Rectangular 1.732050808 1 0.6 f Readout electronics 0.3 Normal 1 1 0.3 f Response time 0 Rectangular 1.732050808 1 0.0 f Integration time 0 Rectangular 1.732050808 1 0.0 f RF ambient conditions 3 Rectangular 1.732050808 1 1.7 f Mech. constraints of robot 0.8 Rectangular 1.732050808 1 0.5 f Probe positioning 5.7 Rectangular 1.732050808 1 3.3 f Extrapolation & integration 4 Rectangular 1.732050808 1 2.3 f Dipole Dipole positioning 2 Rectangular 1.732050808 1 1.2 f Power & Power Drift 4.7 Rectangular 1.732050808 1 2.7 f Phantom and Setup Phantom uncertainty 4 Rectangular 1.732050808 1 2.3 f Liquid conductivity (target) 5 Rectangular 1.732050808 0.64 1.8 f Liquid conductivity (measured) 4.2 Normal 1 0.64 2.7 f Liquid permittivity (target) 10 Rectangular 1.732050808 0.6 3.5 f Liquid permittivity (measured) 9 Normal 1 0.6 5.4 f Combined Standard Uncertainty 13.19 Expanded Uncertainty (k=2) 26.38 Measurement Uncertainty Table in accordance with IEEE Standard 1528-2003 and IEC Standard 62209-1:2005 12. Test Equipment List TEST EQUIPMENT ASSET NO. SERIAL NO. DATE OF CAL. CAL. DUE DATE SPEAG DASY4 Measurement Server 00158 1078 N/A N/A SPEAG Robot 00046 599396-01 N/A N/A SPEAG DAE4 00019 353 21Jun06 21Jun07 SPEAG EX3DV4 E-Field Probe 00213 3600 24Jan07 24Jan08 SPEAG 5GHz Validation Dipole 00126 1031 09May07 09May08 SPEAG SAM Phantom V4.0C 00154 1033 N/A N/A ALS-PR-DIEL Dielectric Probe Kit 00160 260-00953 N/A N/A Gigatronics 8652A Power Meter 00007 1835272 26Mar07 26Mar08 Gigatronics 80701A Power Sensor 00014 1833699 22Jan07 22Jan08 Gigatronics 80701A Power Sensor 00109 1834366 26Mar07 26Mar08 HP 8753ET Network Analyzer 00134 US39170292 20Apr07 20Apr08 Nextec NB00383 Microwave Amplifier 00151 0535 NCR NCR Rohde & Schwarz SMR20 Signal Generator 00006 100104 NCR NCR 2007 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 11 of 11

Date of Evaluation: May 10, 2007 Document Serial No.: SV5800M-051007-R1.2 Evaluation Type: System Validation Validation Dipole: 5800 MHz Fluid Type: Body 5800 MHz SYSTEM VALIDATION Type: 5800 MHz Validation Dipole Asset Number: 00126 Serial Number: 1031 Place of Validation: Celltech Labs Inc. Date of Validation: May 10, 2007 Celltech Labs Inc. certifies that the 5800 MHz System Validation was performed on the date indicated above. Performed by: Cheri Frangiadakis Approved by: Sean Johnston Celltech Labs Inc. 21-364 Lougheed Rd., Kelowna, B.C. V1X 7R8 Canada Tel. 250-765-7650 x Fax. 250-765-7645 x e-mail: info@celltechlabs.com www.celltechlabs.com 2007 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 1 of 11

Date of Evaluation: May 10, 2007 Document Serial No.: SV5800M-051007-R1.2 Evaluation Type: System Validation Validation Dipole: 5800 MHz Fluid Type: Body 1. Dipole Construction & Electrical Characteristics The validation dipole was manufactured by Schmid and Partner Engineering AG. The electrical properties were measured using an HP 8753ET Network Analyzer. The network analyzer was calibrated to the validation dipole N-type connector feed point using an HP85032ET Type N calibration kit. The dipole was placed parallel to a planar phantom at a separation distance of 10.0mm from the simulating fluid using a loss-less dielectric spacer. The measured input impedance is: Feed point impedance at 5800 MHz Re{Z} = 58.436: Im{Z} = 5.3613: Return Loss at 5800 MHz -21.264 dB Reference dipole - basic mechanical parameters 2007 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 2 of 11

«Célltech i f 10 Hay 2607 onsz or CBB erc coo 10 as/rer o ce 21—21.254 an s soe.one ooo niz x CHt Merkers gue a—22.509 d : 9.8 GHz 5.50000 olz a—20.300 ap S.zen00 oz ov 16° a ——I _ & /_\\-/“—fl—¥/—\ 7 Start 4 s00.000 000 Niz STop o 200.000 a08 miiz 10 may 2607 oscsiiss gan en a ucre mseasse sostse cera2pi s ace.ceo aon nz a CHL Harkers 4: 51.047 a Bke to / ie a 250500 tha a sa.a2g a490 2o s.20d08 the hy 1s° 1 cenitcr 5 «50.000 o00 nite spei 1 e00.000 000 mtz

Date of Evaluation: May 10, 2007 Document Serial No.: SV5800M-051007-R1.2 Evaluation Type: System Validation Validation Dipole: 5800 MHz Fluid Type: Body 3. Validation Dipole Dimensions Frequency (MHz) L (mm) H (mm) D (mm) 300 396.0 250.0 6.0 450 270.0 167.0 6.0 835 161.0 89.8 3.6 900 149.0 83.3 3.6 1450 89.1 51.7 3.6 1800 72.0 41.7 3.6 1900 68.0 39.5 3.6 2000 64.5 37.5 3.6 2450 51.5 30.4 3.6 3000 41.5 25.0 3.6 5200 - 5800 20.6 40.65 3.6 4. Validation Phantom The validation phantom is the SAM (Specific Anthropomorphic Mannequin) phantom manufactured by Schmid & Partner Engineering AG. The SAM phantom is a Fiberglass shell integrated in a wooden table. The shape of the shell corresponds to the phantom defined by SCC34-SC2. It enables the dosimetric evaluation of left and right hand phone usage as well as body mounted usage at the flat phantom region. A cover prevents evaporation of the liquid. Reference markings on the phantom allow the complete setup of all predefined phantom positions and measurement grids by manually teaching three points in the robot. Shell Thickness: 2.0 ± 0.1 mm Filling Volume: Approx. 25 liters Dimensions: 50 cm (W) x 100 cm (L) SAM Phantom Fluid Depth (t 15.0 cm) 2007 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 4 of 11

Celltech

Celltech

Date of Evaluation: May 10, 2007 Document Serial No.: SV5800M-051007-R1.2 Evaluation Type: System Validation Validation Dipole: 5800 MHz Fluid Type: Body 7. SAR Measurement Measurements were made using a dosimetric E-field probe EX3DV4 (S/N: 3600, Conversion Factor 4.14). The SAR measurement was performed with the E-field probe in mechanical detection mode only. The setup and determination of the forward power into the dipole was performed using the procedures described below. First the power meter PM1 (including attenuator Att1) is connected to the cable to measure the forward power at the location of the dipole connector (X). The signal generator is adjusted for the desired forward power at the dipole connector (taking into account the attenuation of Att1) as read by power meter PM2. After connecting the cable to the dipole, the signal generator is readjusted for the same reading at power meter PM2. If the signal generator does not allow adjustment in 0.01dB steps, the remaining difference at PM2 must be taken into consideration. PM3 records the reflected power from the dipole to ensure that the value is not changed from the previous value. The reflected power should be 20dB below the forward power. 3D Probe positioner d Field probe Flat Phantom Dipole Dir.Coupler Signal Amp Low 3dB x Generator Pass Cable Att1 Att3 PM1 Att2 PM3 PM2 System Validation Measurement Setup Diagram 2007 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 7 of 11

Date of Evaluation: May 10, 2007 Document Serial No.: SV5800M-051007-R1.2 Evaluation Type: System Validation Validation Dipole: 5800 MHz Fluid Type: Body 8. Measurement Conditions The SAM phantom was filled with 5800 MHz Body tissue simulant. Relative Permittivity: 44.7 (-7.2% deviation from target) Conductivity: 6.22 mho/m (+3.7% deviation from target) Fluid Temperature: 23.6 qC (Start of Test) / 23.2 qC (End of Test) Fluid Depth: t 15.0 cm Environmental Conditions: Ambient Temperature: 23.1qC Humidity: 31% Barometric Pressure: 101.1 kPa The 5800 MHz Body tissue simulant consisted of the following ingredients: Ingredient Percentage by weight Water 64 - 78% Mineral Oil 11 - 18% Emulsifiers 9 - 15% Additives and Salt 2 - 3% IEEE Target Dielectric Parameters: Hr = 48.2 (+/-10%) V = 6.00 S/m (+/-5%) 9. System Validation SAR Results SAR @ 0.25W Input averaged over 1g (W/kg) SAR @ 1W Input averaged over 1g (W/kg) SPEAG Target Measured Deviation SPEAG Target Measured Deviation 18.5 +/- 10% 19.1 +3.3% 74.1 +/- 10% 76.4 +3.1% SAR @ 0.25W Input averaged over 10g (W/kg) SAR @ 1W Input averaged over 10g (W/kg) SPEAG Target Measured Deviation SPEAG Target Measured Deviation 5.13 +/- 10% 5.36 +4.5% 20.52 +/- 10% 21.44 +4.5% Extrapolated Peak SAR SPEAG Target 81.2 +/- 15% Measured 87.3 +7.5% 2007 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 8 of 11

Date of Evaluation: May 10, 2007 Document Serial No.: SV5800M-051007-R1.2 Evaluation Type: System Validation Validation Dipole: 5800 MHz Fluid Type: Body System Validation - 5800 MHz Dipole - May 10, 2007 DUT: Dipole 5GHz; Type: D5GHzV2; Serial: 1031; Asset: 00126 Ambient Temp: 23.1ºC; Fluid Temp: 23.6ºC; Barometric Pressure: 101.1 kPa; Humidity: 31% Communication System: CW Forward Conducted Power: 250 mW Frequency: 5800 MHz; Duty Cycle: 1:1 3 Medium: M5200-5800 Medium parameters used: f = 5800 MHz; ı = 6.22 mho/m; İr = 44.7; ȡ = 1000 kg/m - Probe: EX3DV4 - SN3600; ConvF(4.14, 4.14, 4.14); Calibrated: 24/01/2007 - Sensor-Surface: 2mm (Mechanical Surface Detection) - Electronics: DAE4 Sn353; Calibrated: 21/06/2006 - Phantom: SAM 4.0; Type: Fiberglas; Serial: 1033 - Measurement SW: DASY4, V4.7 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 171 5800 MHz System Validation/Area Scan (9x13x1): Measurement grid: dx=5mm, dy=5mm Maximum value of SAR (measured) = 40.6 mW/g 5800 MHz System Validation/Zoom Scan (7x7x9)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=2.5mm Reference Value = 83.1 V/m; Power Drift = 0.174 dB Peak SAR (extrapolated) = 87.3 W/kg SAR(1 g) = 19.1 mW/g; SAR(10 g) = 5.36 mW/g Maximum value of SAR (measured) = 40.2 mW/g 2007 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 9 of 11

Date of Evaluation: May 10, 2007 Document Serial No.: SV5800M-051007-R1.2 Evaluation Type: System Validation Validation Dipole: 5800 MHz Fluid Type: Body 10. Measured Fluid Dielectric Parameters System Validation - 5800 MHz (Body) ************************************************************ Celltech Labs Inc. Test Result for UIM Dielectric Parameter Mon 10/May/2007 Frequency (GHz) FCC_eH FCC Bulletin 65 Supplement C (June 2001) Limits for Head Epsilon FCC_sH FCC Bulletin 65 Supplement C (June 2001) Limits for Head Sigma FCC_eB FCC Limits for Body Epsilon FCC_sB FCC Limits for Body Sigma Test_e Epsilon of UIM Test_s Sigma of UIM ************************************************************ Freq FCC_eB FCC_sB Test_e Test_s 5.7000 48.34 5.88 44.57 6.11 5.7100 48.32 5.89 44.13 6.03 5.7200 48.31 5.91 43.79 6.06 5.7300 48.30 5.92 43.57 6.11 5.7400 48.28 5.93 43.53 6.26 5.7500 48.27 5.94 43.52 6.33 5.7600 48.25 5.95 43.73 6.49 5.7700 48.24 5.96 44.19 6.52 5.7800 48.23 5.98 44.57 6.48 5.7900 48.21 5.99 44.66 6.37 5.8000 48.20 6.00 44.67 6.22 5.8100 48.19 6.01 44.53 6.14 5.8200 48.17 6.02 44.13 6.07 5.8300 48.16 6.04 43.75 6.09 5.8400 48.15 6.05 43.46 6.20 5.8500 48.13 6.06 43.36 6.33 5.8600 48.12 6.07 43.32 6.51 5.8700 48.10 6.08 43.57 6.64 5.8800 48.09 6.09 43.99 6.65 5.8900 48.08 6.11 44.33 6.63 5.9000 48.06 6.12 44.43 6.55 2007 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 10 of 11

Date of Evaluation: May 10, 2007 Document Serial No.: SV5800M-051007-R1.2 Evaluation Type: System Validation Validation Dipole: 5800 MHz Fluid Type: Body 11. Measurement Uncertainties UNCERTAINTY BUDGET FOR SYSTEM VALIDATION Uncertainty Uncertainty Probability ci Error Description Value Divisor Value Vi or Veff Distribution 1g ±% ±% (1g) Measurement System Probe calibration (5800 MHz) 6.55 Normal 1 1 6.55 f Axial isotropy of the probe 4.7 Rectangular 1.732050808 1 2.7 f Spherical isotropy of the probe 9.6 Rectangular 1.732050808 1 5.5 f Spatial resolution 0 Rectangular 1.732050808 1 0.0 f Boundary effects 0.1 Rectangular 1.732050808 1 0.1 f Probe linearity 4.7 Rectangular 1.732050808 1 2.7 f Detection limit 1 Rectangular 1.732050808 1 0.6 f Readout electronics 0.3 Normal 1 1 0.3 f Response time 0 Rectangular 1.732050808 1 0.0 f Integration time 0 Rectangular 1.732050808 1 0.0 f RF ambient conditions 3 Rectangular 1.732050808 1 1.7 f Mech. constraints of robot 0.8 Rectangular 1.732050808 1 0.5 f Probe positioning 5.7 Rectangular 1.732050808 1 3.3 f Extrapolation & integration 4 Rectangular 1.732050808 1 2.3 f Dipole Dipole positioning 2 Rectangular 1.732050808 1 1.2 f Power & Power Drift 4.7 Rectangular 1.732050808 1 2.7 f Phantom and Setup Phantom uncertainty 4 Rectangular 1.732050808 1 2.3 f Liquid conductivity (target) 5 Rectangular 1.732050808 0.64 1.8 f Liquid conductivity (measured) 3.7 Normal 1 0.64 2.4 f Liquid permittivity (target) 10 Rectangular 1.732050808 0.6 3.5 f Liquid permittivity (measured) 7.2 Normal 1 0.6 4.3 f Combined Standard Uncertainty 12.72 Expanded Uncertainty (k=2) 25.45 Measurement Uncertainty Table in accordance with IEEE Standard 1528-2003 and IEC Standard 62209-1:2005 12. Test Equipment List TEST EQUIPMENT ASSET NO. SERIAL NO. DATE OF CAL. CAL. DUE DATE SPEAG DASY4 Measurement Server 00158 1078 N/A N/A SPEAG Robot 00046 599396-01 N/A N/A SPEAG DAE4 00019 353 21Jun06 21Jun07 SPEAG EX3DV4 E-Field Probe 00213 3600 24Jan07 24Jan08 SPEAG 5GHz Validation Dipole 00126 1031 10May07 10May08 SPEAG SAM Phantom V4.0C 00154 1033 N/A N/A ALS-PR-DIEL Dielectric Probe Kit 00160 260-00953 N/A N/A Gigatronics 8652A Power Meter 00007 1835272 26Mar07 26Mar08 Gigatronics 80701A Power Sensor 00014 1833699 22Jan07 22Jan08 Gigatronics 80701A Power Sensor 00109 1834366 26Mar07 26Mar08 HP 8753ET Network Analyzer 00134 US39170292 20Apr07 20Apr08 Nextec NB00383 Microwave Amplifier 00151 0535 NCR NCR Rohde & Schwarz SMR20 Signal Generator 00006 100104 NCR NCR 2007 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 11 of 11


Document Created: 2008-03-20 16:20:31
Document Modified: 2008-03-20 16:20:31
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC