Test Report

FCC ID: KA2SM22AA1

Test Report

Download: PDF
FCCID_1336132

Compliance Certification Services Inc. Report No.: T100617011-RP1 FCC ID: KA2SM22AA1 Date of Issue: September 1, 2010 FCC 47 CFR PART 15 SUBPART C TEST REPORT For Remote controller Model Number: DSM-22A, DSM-22 Trade Name: D-Link Issued to D-Link Corporation 17595 Mt. Herrmann Fountain Valley California 92708 United States Issued by Compliance Certification Services Inc. No. 11, Wu-Gong 6th Rd., Wugu Industrial Park, Taipei Hsien 248, Taiwan (R.O.C.) http://www.ccsrf.com service@ccsrf.com Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. Page 1 Total Page: 29 Rev. 00

Compliance Certification Services Inc. Report No.: T100617011-RP1 FCC ID: KA2SM22AA1 Date of Issue: September 1, 2010 TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION................................................................................................. 3 2. EUT DESCRIPTION....................................................................................................................... 4 3. TEST METHODOLOGY................................................................................................................ 5 3.1 EUT CONFIGURATION ................................................................................................................. 5 3.2 EUT EXERCISE ............................................................................................................................. 5 3.3 GENERAL TEST PROCEDURES...................................................................................................... 5 3.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS.................................................. 6 3.5 DESCRIPTION OF TEST MODES .................................................................................................... 6 4. INSTRUMENT CALIBRATION.................................................................................................... 7 4.1 MEASURING INSTRUMENT CALIBRATION ............................................................................... 7 4.2 MEASUREMENT EQUIPMENT USED .................................................................................. 7 4.3 MEASUREMENT UNCERTAINTY ........................................................................................ 8 5. FACILITIES AND ACCREDITATIONS....................................................................................... 9 5.1 FACILITIES .................................................................................................................................. 9 5.2 EQUIPMENT................................................................................................................................. 9 5.3 TABLE OF ACCREDITATIONS AND LISTINGS .............................................................................. 10 6. SETUP OF EQUIPMENT UNDER TEST.................................................................................... 11 6.1 SETUP CONFIGURATION OF EUT ................................................................................................ 11 6.2 SUPPORT EQUIPMENT ........................................................................................................ 11 7. FCC PART 15.249 REQUIREMENTS......................................................................................... 12 7.1 20 DB BANDWIDTH.............................................................................................................. 12 7.2 BAND EDGES MEASUREMENT ......................................................................................... 15 7.3 SPURIOUS EMISSION .......................................................................................................... 20 7.4 POWERLINE CONDUCTED EMISSIONS ........................................................................... 28 APPENDIX I PHOTOGRAPHS OF TEST SETUP ............................................................................ 29 APPENDIX 1 - PHOTOGRAPHS OF EUT Page 2 Rev. 00

Compliance Certification Services Inc. Report No.: T100617011-RP1 FCC ID: KA2SM22AA1 Date of Issue: September 1, 2010 1. TEST RESULT CERTIFICATION Applicant: D-Link Corporation 17595 Mt. Herrmann Fountain Valley California 92708 United States Equipment Under Test: Remote controller Trade Name: D-Link Model Number: DSM-22A, DSM-22 Date of Test: June 18 ~ September 1, 2010 APPLICABLE STANDARDS STANDARD TEST RESULT FCC 47 CFR Part 15 Subpart C No non-compliance noted We hereby certify that: The above equipment was tested by Compliance Certification Services Inc. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4: 2003 and the energy emitted by the sample EUT tested as described in this report is in compliance with the requirements emission limits of FCC Rules Part 15.207, 15.209 and 15.249. The test results of this report relate only to the tested sample identified in this report. Approved by: Reviewed by: Rex Lai Gina Lo Section Manager Section Manager Compliance Certification Services Inc. Compliance Certification Services Inc. Page 3 Rev. 00

Compliance Certification Services Inc. Report No.: T100617011-RP1 FCC ID: KA2SM22AA1 Date of Issue: September 1, 2010 2. EUT DESCRIPTION Product Remote controller Trade Name D-Link Model Number DSM-22A, DSM-22 All the specification and layout are identical except they come with Model Discrepancy different model numbers for marketing purposes. Power Supply Coin-cell Battery: 3V (CR2032) Frequency Range 2400 ~ 2483.5 MHz Operating Frequency 2403 ~ 2475MHz Frequency Number 73 Channels Channel Spacing 1MHz Modulation Technique GFSK Antenna Gain 0.88 dBi Antenna Designation Printed Antenna Remark: 1. The sample selected for test was production product and was provided by manufacturer. 2. This submittal(s) (test report) is intended for FCC ID: KA2SM22AA1 filing to comply with Section 15.107, 15.109, 15.207, 15.209, 15.249 (FCC Part 15, Subpart C Rules.) Page 4 Rev. 00

Compliance Certification Services Inc. Report No.: T100617011-RP1 FCC ID: KA2SM22AA1 Date of Issue: September 1, 2010 3. TEST METHODOLOGY The tests documented in this report were performed in accordance with ANSI C63.4: 2003 and FCC CFR 47 Part 15.207, 15.209 and 15.249. 3.1 EUT CONFIGURATION The EUT configuration for testing is installed on RF field strength measurement to meet the Commissions requirement and operating in a manner that intends to maximize its emission characteristics in a continuous normal application. 3.2 EUT EXERCISE The EUT was operated in the engineering mode to fix the TX frequency that was for the purpose of the measurements. According to its specifications, the EUT must comply with the requirements of the Section 15.207, 15.209,15.249 under the FCC Rules Part 15 Subpart C. 3.3 GENERAL TEST PROCEDURES Conducted Emissions The EUT is placed on the turntable, which is 0.8 m above ground plane. According to the requirements in Section 13.1.4.1 of ANSI C63.4: 2003 Conducted emissions from the EUT measured in the frequency range between 0.15 MHz and 30MHz using CISPR Quasi-peak and average detector modes. Radiated Emissions The EUT is placed on a turn table, which is 0.8 m above ground plane. The turntable shall rotate 360 degrees to determine the position of maximum emission level. EUT is set 3m away from the receiving antenna, which varied from 1m to 4m to find out the highest emission. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. In order to find out the maximum emissions, exploratory radiated emission measurements were made according to the requirements in Section 13.1.4.1 of ANSI C63.4: 2003. Page 5 Rev. 00

Compliance Certification Services Inc. Report No.: T100617011-RP1 FCC ID: KA2SM22AA1 Date of Issue: September 1, 2010 3.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS (a) Except as shown in paragraph (d) of this section, only spurious emissions are permitted in any of the frequency bands listed below: MHz MHz MHz GHz 0.090 - 0.110 16.42 - 16.423 399.9 - 410 4.5 - 5.15 1 0.495 - 0.505 16.69475 - 16.69525 608 - 614 5.35 - 5.46 2.1735 - 2.1905 16.80425 - 16.80475 960 - 1240 7.25 - 7.75 4.125 - 4.128 25.5 - 25.67 1300 - 1427 8.025 - 8.5 4.17725 - 4.17775 37.5 - 38.25 1435 - 1626.5 9.0 - 9.2 4.20725 - 4.20775 73 - 74.6 1645.5 - 1646.5 9.3 - 9.5 6.215 - 6.218 74.8 - 75.2 1660 - 1710 10.6 - 12.7 6.26775 - 6.26825 108 - 121.94 1718.8 - 1722.2 13.25 - 13.4 6.31175 - 6.31225 123 - 138 2200 - 2300 14.47 - 14.5 8.291 - 8.294 149.9 - 150.05 2310 - 2390 15.35 - 16.2 8.362 - 8.366 156.52475 - 2483.5 - 2500 17.7 - 21.4 8.37625 - 8.38675 156.52525 2655 - 2900 22.01 - 23.12 8.41425 - 8.41475 156.7 - 156.9 3260 - 3267 23.6 - 24.0 12.29 - 12.293 162.0125 - 167.17 3332 - 3339 31.2 - 31.8 12.51975 - 12.52025 167.72 - 173.2 3345.8 - 3358 36.43 - 36.5 12.57675 - 12.57725 240 - 285 3600 - 4400 (2) 13.36 - 13.41 322 - 335.4 1 Until February 1, 1999, this restricted band shall be 0.490-0.510 MHz. 2 Above 38.6 (b) Except as provided in paragraphs (d) and (e), the field strength of emissions appearing within these frequency bands shall not exceed the limits shown in Section 15.209. At frequencies equal to or less than 1000 MHz, compliance with the limits in Section 15.209 shall be demonstrated using measurement instrumentation employing a CISPR quasi-peak detector. Above 1000 MHz, compliance with the emission limits in Section 15.209 shall be demonstrated based on the average value of the measured emissions. The provisions in Section 15.35 apply to these measurements. 3.5 DESCRIPTION OF TEST MODES The EUT (model: DSM-22A) had been tested under operating condition. After verification, all tests were carried out with the worst case test modes as shown below except radiated spurious emission below 1GHz, which worst case was in normal link mode only. Channel Low(2403MHz), Channel Mid(2440MHz) and Channel High(2475MHz) were chosen for the final testing. The field strength of spurious emission was measured in the following position: EUT stand-up position (Z axis), lie-down position (X, Y axis). The worst emission was found in lie-down position (X axis) and the worst case was recorded. Page 6 Rev. 00

Compliance Certification Services Inc. Report No.: T100617011-RP1 FCC ID: KA2SM22AA1 Date of Issue: September 1, 2010 4. INSTRUMENT CALIBRATION 4.1 MEASURING INSTRUMENT CALIBRATION The measuring equipment, which was utilized in performing the tests documented herein, has been calibrated in accordance with the manufacturer's recommendations for utilizing calibration equipment, which is traceable to recognized national standards. 4.2 MEASUREMENT EQUIPMENT USED Equipment Used for Emissions Measurement Remark: Each piece of equipment is scheduled for calibration once a year and Loop Antenna is scheduled for calibration once three years. 3M Semi Anechoic Chamber Name of Equipment Manufacturer Model Serial Number Calibration Due Spectrum Analyzer Agilent E4446A US42510252 10/26/2010 EMI Test Receiver R&S ESCI 100064 02/04/2011 Pre-Amplifier Mini-Circults ZFL-1000LN SF350700823 01/13/2011 AFS44-00102650- Pre-Amplifier MITEQ 1415367 11/20/2010 42-10P-44 Bilog Antenna Sunol Sciences JB3 A030105 09/11/2010 Horn Antenna EMCO 3117 00055165 12/07/2010 Loop Antenna EMCO 6502 8905/2356 06/10/2013 Turn Table CCS CC-T-1F N/A N.C.R Antenna Tower CCS CC-A-1F N/A N.C.R Controller CCS CC-C-1F N/A N.C.R Site NSA CCS N/A N/A 12/31/2010 Test S/W EZ-EMC (CCS-3A1RE) Page 7 Rev. 00

Compliance Certification Services Inc. Report No.: T100617011-RP1 FCC ID: KA2SM22AA1 Date of Issue: September 1, 2010 4.3 MEASUREMENT UNCERTAINTY PARAMETER UNCERTAINTY 3M Semi Anechoic Chamber / 30M~200M +/- 4.0606 3M Semi Anechoic Chamber / 200M~1000M +/- 3.9979 3M Semi Anechoic Chamber / 1G~8G +/- 2.5790 3M Semi Anechoic Chamber / 8G~18G +/- 2.5928 3M Semi Anechoic Chamber / 18G~26G +/- 2.7212 3M Semi Anechoic Chamber / 26G~40G +/- 2.9520 Remark: This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. Page 8 Rev. 00

Compliance Certification Services Inc. Report No.: T100617011-RP1 FCC ID: KA2SM22AA1 Date of Issue: September 1, 2010 5. FACILITIES AND ACCREDITATIONS 5.1 FACILITIES All measurement facilities used to collect the measurement data are located at No. 199, Chunghsen Road, Hsintien City, Auerbach / Opf GERMANY Tel: 886-2-2217-0894 / Fax: 886-2-2217-1029 No.11, Wugong 6th Rd., Wugu Industrial Park, Taipei Hsien 248, Taiwan Tel: 886-2-2299-9720 / Fax: 886-2-2298-4045 No.81-1, Lane 210, Bade 2nd Rd., Luchu Hsiang, Taoyuan Hsien 338, Taiwan Tel: 886-3-324-0332 / Fax: 886-3-324-5235 The sites are constructed in conformance with the requirements of ANSI C63.7, ANSI C63.4 and CISPR Publication 22. 5.2 EQUIPMENT Radiated emissions are measured with one or more of the following types of linearly polarized antennas: tuned dipole, biconical, log periodic, bi-log, and/or ridged waveguide, horn. Spectrum analyzers with pre-selectors and quasi-peak detectors are used to perform radiated measurements. Conducted emissions are measured with Line Impedance Stabilization Networks and EMI Test Receivers. Calibrated wideband preamplifiers, coaxial cables, and coaxial attenuators are also used for making measurements. All receiving equipment conforms to CISPR Publication 16-1, “Radio Interference Measuring Apparatus and Measurement Methods.” Page 9 Rev. 00

Compliance Certification Services Inc. Report No.: T100617011-RP1 FCC ID: KA2SM22AA1 Date of Issue: September 1, 2010 5.3 TABLE OF ACCREDITATIONS AND LISTINGS Country Agency Scope of Accreditation Logo 3M Semi Anechoic Chamber (FCC MRA: TW1039) to perform USA FCC FCC Part 15 measurements FCC MRA: TW1039 LP0002, RTTE01, FCC Method-47 CFR Part 15 Subpart C, D, E, RSS-210, RSS-310 IDA TS SRD, AS/NZS 4268, AS/NZS 4771, TS 12.1 & 12,2, ETSI EN 300 440-1, ETSI EN 300 440-2, ETSI EN 300 328, ETSI EN 300 220-1, ETSI EN 300 220-2, ETSI EN 301 893, ETSI EN 301 489-1/3/7/17 Taiwan TAF FCC OET Bulletin 65 + Supplement C, EN 50360, EN 50361, EN 50371, RSS 102, EN 50383, EN 50385, EN 50392, IEC 62209, CNS 14958-1, CNS 14959 FCC Method –47 CFR Part 15 Subpart B IEC / EN 61000-3-2, IEC / EN 61000-3-3, IEC / EN 61000-4-2/3/4/5/6/8/11 Industry Canada 3M Semi Anechoic Chamber (IC 2324G-1 / IC 2324G-2) to perform IC 2324G-1 Canada IC 2324G-2 * No part of this report may be used to claim or imply product endorsement by A2LA or any agency of the US Government. Page 10 Rev. 00

Compliance Certification Services Inc. Report No.: T100617011-RP1 FCC ID: KA2SM22AA1 Date of Issue: September 1, 2010 6. SETUP OF EQUIPMENT UNDER TEST 6.1 SETUP CONFIGURATION OF EUT See test photographs attached in Appendix I for the actual connections between EUT and support equipment. 6.2 SUPPORT EQUIPMENT No Equipment Model Serial No. FCC ID Trade Name Data Cable Power Cord AC I/P: Unshielded, 1.8m Notebook PC 1. DELL PP19L GK102 A00 QDS-BRCM1021 N/A DC O/P: (Remote) Unshielded, 1.8m with a core Remark: 1. All the equipment/cables were placed in the worst-case configuration to maximize the emission during the test. 2. Grounding was established in accordance with the manufacturer’s requirements and conditions for the intended use. Page 11 Rev. 00

Compliance Certification Services Inc. Report No.: T100617011-RP1 FCC ID: KA2SM22AA1 Date of Issue: September 1, 2010 7. FCC PART 15.249 REQUIREMENTS 7.1 20 DB BANDWIDTH LIMIT None; for reporting purposes only. Test Configuration Antenna tower 3m Horn antenna EUT 4m Spectrum analyzer Turntable 1m 0.8m Pre-amp TEST PROCEDURE 1. Place the EUT on the table and set it in the transmitting mode. 2. Remove the antenna from the EUT and then connect a low loss RF cable from the antenna port to the spectrum analyzer. 3. Set the spectrum analyzer as RBW=20kHz, VBW = 62kHz, Span = 5MHz, Sweep = auto. 4. Mark the peak frequency and 20dB (upper and lower) frequency. 5. Repeat until all the rest channels are investigated. TEST RESULTS No non-compliance noted Test Data Frequency 20dB Bandwidth Channel (MHz) (MHz) Low 2403 1.000 Mid 2440 0.992 High 2475 1.025 Page 12 Rev. 00

Compliance Certification Services Inc. Report No.: T100617011-RP1 FCC ID: KA2SM22AA1 Date of Issue: September 1, 2010 Test Plot CH Low CH Mid Page 13 Rev. 00

Compliance Certification Services Inc. Report No.: T100617011-RP1 FCC ID: KA2SM22AA1 Date of Issue: September 1, 2010 CH High Page 14 Rev. 00

Compliance Certification Services Inc. Report No.: T100617011-RP1 FCC ID: KA2SM22AA1 Date of Issue: September 1, 2010 7.2 BAND EDGES MEASUREMENT LIMIT 1. In the above emission table, the tighter limit applies at the band edges. Frequency Field Strength Field Strength (MHz) (μV/m at 3-meter) (dBμV/m at 3-meter) 30-88 100 40 88-216 150 43.5 216-960 200 46 Above 960 500 54 2. As shown in Section 15.35(b), for frequencies above 1000 MHz, the above field strength limits in paragraphs (a) and (b) of this section are based on average limits. However, the peak field strength of any emission shall not exceed the maximum permitted average limits specified above by more than 20 dB under any condition of modulation. For point-to-point operation under paragraph (b) of this section, the peak field strength shall not exceed 2500 millivolts/meter at 3 meters along the antenna azimuth. Test Configuration Antenna tower 3m Horn antenna EUT 4m Spectrum analyzer Turntable 1m 0.8m Pre-amp TEST PROCEDURE 1. The EUT is placed on a turntable, which is 0.8m above the ground plane. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find out the highest emission. 4. Set the spectrum analyzer in the following setting in order to capture the lower and upper band-edges of the emission: (a) PEAK: RBW=VBW=1MHz / Sweep=AUTO (b) AVERAGE: RBW=1MHz / VBW=10Hz / Sweep=AUTO 5. Repeat the procedures until all the PEAK and AVERAGE versus POLARIZATION are measured. TEST RESULTS Refer to attach spectrum analyzer data chart. Page 15 Rev. 00

Compliance Certification Services Inc. Report No.: T100617011-RP1 FCC ID: KA2SM22AA1 Date of Issue: September 1, 2010 Band Edges (CH Low) Detector mode: Peak Polarity: Vertical Detector mode: Average Polarity: Vertical Page 16 Rev. 00

Compliance Certification Services Inc. Report No.: T100617011-RP1 FCC ID: KA2SM22AA1 Date of Issue: September 1, 2010 Detector mode: Peak Polarity: Horizontal Detector mode: Average Polarity: Horizontal Page 17 Rev. 00

Compliance Certification Services Inc. Report No.: T100617011-RP1 FCC ID: KA2SM22AA1 Date of Issue: September 1, 2010 Band Edges (CH High) Detector mode: Peak Polarity: Vertical Detector mode: Average Polarity: Vertical Page 18 Rev. 00

Compliance Certification Services Inc. Report No.: T100617011-RP1 FCC ID: KA2SM22AA1 Date of Issue: September 1, 2010 Detector mode: Peak Polarity: Horizontal Detector mode: Average Polarity: Horizontal Page 19 Rev. 00

Compliance Certification Services Inc. Report No.: T100617011-RP1 FCC ID: KA2SM22AA1 Date of Issue: September 1, 2010 7.3 SPURIOUS EMISSION LIMIT 1. In the section 15.249(a): Except as provided in paragraph (b) of this section, the field strength of emissions from intentional radiators operated within these frequency bands shall comply with the following: Fundamental Field Strength of Fundamental Field Strength of Harmonics Frequency Field Strength (μV/m) (MHz) (mV/m) 902-928 MHz 50 500 2400 - 2483.5 MHz 50 500 5725 - 5875 MHz 50 500 24.0 - 24.25 GHz 250 2500 2. Except as provided elsewhere in this Subpart, the emissions from an intentional radiator shall not exceed the field strength levels specified in the following table: Frequency Field Strength Measurement Distance (MHz) (μV/m) (m) 30-88 100* 3 88-216 150* 3 216-960 200* 3 Above 960 500 3 Remark: Except as provided in paragraph (g), fundamental emissions from intentional radiators operating under this Section shall not be located in the frequency bands 54-72 MHz, 76-88 MHz, 174-216 MHz or 470-806 MHz. However, operation within these frequency bands is permitted under other sections of this Part, e.g., Sections 15.231 and 15.241. 3. In the above emission table, the tighter limit applies at the band edges. Frequency Field Strength Field Strength (MHz) (μV/m at 3-meter) (dBμV/m at 3-meter) 30-88 100 40 88-216 150 43.5 216-960 200 46 Above 960 500 54 Page 20 Rev. 00

Compliance Certification Services Inc. Report No.: T100617011-RP1 FCC ID: KA2SM22AA1 Date of Issue: September 1, 2010 Test Configuration 9kHz ~ 30MHz 3m Loop antenna EUT Spectrum / Receiver Turntable 1m 0.8m Reference ground plane 30MHz ~ 1GHz Antenna tower 3m Bi-log antenna EUT 4m Spectrum analyzer Turntable 1m 0.8m Reference ground plane Page 21 Rev. 00

Compliance Certification Services Inc. Report No.: T100617011-RP1 FCC ID: KA2SM22AA1 Date of Issue: September 1, 2010 Above 1 GHz Antenna tower 3m Horn antenna EUT 4m Spectrum analyzer Turntable 1m 0.8m Pre-amp Page 22 Rev. 00

Compliance Certification Services Inc. Report No.: T100617011-RP1 FCC ID: KA2SM22AA1 Date of Issue: September 1, 2010 TEST PROCEDURE 1. The EUT is placed on a turntable, which is 0.8m above ground plane. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find out the highest emissions. 4. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 5. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 6. Set the spectrum analyzer in the following setting as: Below 1GHz: RBW=100kHz / VBW=300kHz / Sweep=AUTO Above 1GHz: (a) PEAK: RBW=VBW=1MHz / Sweep=AUTO (b) AVERAGE: RBW=1MHz / VBW=10Hz / Sweep=AUTO 7. Repeat above procedures until the measurements for all frequencies are complete. Page 23 Rev. 00

Compliance Certification Services Inc. Report No.: T100617011-RP1 FCC ID: KA2SM22AA1 Date of Issue: September 1, 2010 Below 1 GHz Operation Mode: Normal Link Test Date: June 18, 2010 Temperature: 25°C Tested by: Ming Chen Humidity: 55% RH Polarity: Ver. / Hor. Detector Frequency Ant.Pol. Reading Correction Factor Result Limit 3m Margin Mode (MHz) (H/V) (dBuV) (dB/m) (dBuV/m) (dBuV/m) (dB) (PK/QP) 243.40 V QP 37.78 -11.03 26.75 46.00 -19.25 296.75 V QP 36.70 -9.27 27.42 46.00 -18.58 351.72 V QP 33.05 -8.02 25.03 46.00 -20.97 405.07 V QP 32.96 -6.97 25.99 46.00 -20.01 647.57 V QP 32.72 -2.95 29.77 46.00 -16.23 728.40 V QP 29.20 -2.13 27.07 46.00 -18.93 30.00 H QP 21.49 -1.86 19.63 40.00 -20.37 191.67 H QP 32.22 -10.63 21.59 43.50 -21.91 207.83 H QP 28.15 -10.53 17.62 43.50 -25.88 224.00 H QP 27.90 -11.39 16.51 46.00 -29.49 351.72 H QP 25.44 -8.02 17.42 46.00 -28.58 767.20 H QP 24.83 -1.65 23.17 46.00 -22.83 Remark: 1. No emission found between lowest internal used/generated frequency to 30MHz (9kHz~30MHz). 2. Radiated emissions measured were made with an instrument using peak/quasi-peak detector mode. 3. Quasi-peak test would be performed if the peak result were greater than the quasi-peak limit or as required by the applicant. 4. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 5. Margin (dB) = Remark result (dBuV/m) – Quasi-peak limit (dBuV/m). Page 24 Rev. 00

Compliance Certification Services Inc. Report No.: T100617011-RP1 FCC ID: KA2SM22AA1 Date of Issue: September 1, 2010 Above 1 GHz Operation Mode: Tx / CH Low Test Date: August 30, 2010 Temperature: 25°C Tested by: Ming Chen Humidity: 55% RH Polarity: Ver. / Hor. Ant. Peak AV Ant. / CL Result Peak AV Freq. Margin Pol Reading Reading CF Peak AV Limit Limit Remark (MHz) (dB) H/V (dBuV) (dBuV) (dB) (dBuV/m) (dBuV/m) (dBuV/m) (dBuV/m) 2403.043 V 94.21 72.92 -2.95 91.26 69.97 114.00 94.00 -24.03 AVG 1310.00 V 55.87 --- -9.08 46.79 --- 74.00 54.00 -7.21 Peak 4808.33 V 57.16 41.84 1.18 58.34 43.02 74.00 54.00 -10.98 AVG N/A 2403.043 H 106.5 78.13 -2.95 103.55 75.18 114.00 94.00 -18.82 AVG 1710.00 H 55.78 --- -6.82 48.95 --- 74.00 54.00 -5.05 Peak 4808.33 H 61.96 42.89 1.18 63.14 44.07 74.00 54.00 -9.93 AVG N/A Remark: 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 6. Margin (dB) = Remark result (dBuV/m) – Average limit (dBuV/m). Peak detector mode and average detector mode of the emission shown in Result column. Page 25 Rev. 00

Compliance Certification Services Inc. Report No.: T100617011-RP1 FCC ID: KA2SM22AA1 Date of Issue: September 1, 2010 Operation Mode: Tx / CH Mid Test Date: August 30, 2010 Temperature: 25°C Tested by: Ming Chen Humidity: 55% RH Polarity: Ver. / Hor. Ant. Peak AV Ant. / CL Result Peak AV Freq. Margin Pol Reading Reading CF Peak AV Limit Limit Remark (MHz) (dB) H/V (dBuV) (dBuV) (dB) (dBuV/m) (dBuV/m) (dBuV/m) (dBuV/m) 2440.000 V 93.26 72.75 -2.84 90.42 69.91 114.00 94.00 -24.09 AVG 1553.33 V 54.91 --- -8.27 46.64 --- 74.00 54.00 -7.36 Peak 4883.33 V 53.57 40.67 1.16 54.72 41.83 74.00 54.00 -12.17 AVG N/A 2440.00 H 101.24 77.78 -2.84 98.40 74.94 114.00 94.00 -19.06 AVG 1500.00 H 55.69 --- -8.76 46.93 --- 74.00 54.00 -7.07 Peak 4883.33 H 61.66 43.39 1.16 62.82 44.55 74.00 54.00 -9.45 AVG N/A Remark: 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 6. Margin (dB) = Remark result (dBuV/m) – Average limit (dBuV/m). Peak detector mode and average detector mode of the emission shown in Result column. Page 26 Rev. 00

Compliance Certification Services Inc. Report No.: T100617011-RP1 FCC ID: KA2SM22AA1 Date of Issue: September 1, 2010 Operation Mode: Tx / CH High Test Date: August 30, 2010 Temperature: 25°C Tested by: Ming Chen Humidity: 55% RH Polarity: Ver. / Hor. Ant. Peak AV Ant. / CL Result Peak AV Freq. Margin Pol Reading Reading CF Peak AV Limit Limit Remark (MHz) (dB) H/V (dBuV) (dBuV) (dB) (dBuV/m) (dBuV/m) (dBuV/m) (dBuV/m) 2475.000 V 94.96 73.60 -2.74 92.22 70.86 114.00 94.00 -23.14 AVG 1726.67 V 55.01 --- -6.67 48.34 --- 74.00 54.00 -5.66 Peak 4950.00 V 53.72 40.81 1.14 54.86 41.95 74.00 54.00 -12.05 AVG N/A 2475.000 H 103.53 79.77 -2.73 100.80 77.04 114.00 94.00 -16.96 AVG 1470.00 H 55.11 --- -8.81 46.30 --- 74.00 54.00 -7.70 Peak 4950.00 H 64.64 43.80 1.14 65.77 44.94 74.00 54.00 -9.06 AVG 7425.00 H 50.74 36.48 5.37 56.11 41.85 74.00 54.00 -12.15 AVG N/A Remark: 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 6. Margin (dB) = Remark result (dBuV/m) – Average limit (dBuV/m). Peak detector mode and average detector mode of the emission shown in Result column. Page 27 Rev. 00

Compliance Certification Services Inc. Report No.: T100617011-RP1 FCC ID: KA2SM22AA1 Date of Issue: September 1, 2010 7.4 POWERLINE CONDUCTED EMISSIONS LIMIT According to §15.207(a), except as shown in paragraphs (b) and (c) of this section, for an intentional radiator that is designed to be connected to the public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power line on any frequency or frequencies within the band 150 kHz to 30 MHz shall not exceed the limits in the following table, as measured using a 50 µH/50 ohms line impedance stabilization network (LISN). Compliance with the provisions of this paragraph shall be based on the measurement of the radio frequency voltage between each power line and ground at the power terminal. The lower limit applies at the boundary between the frequency ranges. Limits Frequency Range (dBμV) (MHz) Quasi-peak Average 0.15 to 0.50 66 to 56* 56 to 46* 0.50 to 5 56 46 5 to 30 60 50 * Decreases with the logarithm of the frequency. Test Configuration See test photographs attached in Appendix I for the actual connections between EUT and support equipment. TEST PROCEDURE 1. The EUT was placed on a table, which is 0.8m above ground plane. 2. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 3. Repeat above procedures until all frequency measured were complete. TEST RESULTS Not applicable (Since the EUT is powered by battery) Page 28 Rev. 00


Document Created: 2010-09-01 15:52:15
Document Modified: 2010-09-01 15:52:15
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC