RF Test Report B1-B4

FCC ID: KA2IR885LA1

Test Report

Download: PDF
FCCID_3237155

SPORTON International Inc. No. 52, Hwa Ya 1st Rd., Hwa Ya Technology Park, Kwei-Shan Hsiang, Tao Yuan Hsien, Taiwan, R.O.C. Ph: 886-3-327-3456 / FAX: 886-3-327-0973 / www.sporton.com.tw FCC RADIO TEST REPORT Applicant’s company D-Link Corporation Applicant Address No.289, Sinhu 3rd Rd., Neihu District, Taipei City 114, Taiwan, R.O.C. FCC ID KA2IR885LA1 Product Name AC3150 Ultra Wi-Fi Router Brand Name D-Link Model No. DIR-885L Test Rule Part(s) 47 CFR FCC Part 15 Subpart E § 15.407 Test Freq. Range 5150 ~ 5250 MHz / 5725 ~ 5850 MHz Received Date May 11, 2015 Final Test Date Jul. 05, 2016 Submission Type Class II Change Statement Test result included is for the IEEE 802.11n and IEEE 802.11a/ac of the product. The test result in this report refers exclusively to the presented test model / sample. Without written approval of SPORTON International Inc., the test report shall not be reproduced except in full. The measurements and test results shown in this test report were made in accordance with the procedures and found in compliance with the limit given in ANSI C63.10-2013, 47 CFR FCC Part 15 Subpart E, KDB789033 D02 v01r03, KDB662911 D01 v02r01, KDB644545 D03 v01, ET Docket No. 13–49; FCC 16–24. The test equipment used to perform the test is calibrated and traceable to NML/ROC. Report Format Version: Rev. 01

Report No.: FR551807-06AB Table of Contents 1. VERIFICATION OF COMPLIANCE ....................................................................................................................... 1 2. SUMMARY OF THE TEST RESULT .......................................................................................................................... 2 3. GENERAL INFORMATION .................................................................................................................................. 3 3.1. Product Details....................................................................................................................................................................................3 3.2. Accessories.........................................................................................................................................................................................4 3.3. Table for Filed Antenna.......................................................................................................................................................................5 3.4. Table for Carrier Frequencies .............................................................................................................................................................6 3.5. Table for Test Modes ...........................................................................................................................................................................6 3.6. Table for Testing Locations..................................................................................................................................................................7 3.7. Table for Class II Change ...................................................................................................................................................................7 3.8. Table for Supporting Units ...................................................................................................................................................................7 3.9. EUT Operation during Test ...................................................................................................................................................................7 3.10. Duty Cycle ..........................................................................................................................................................................................7 3.11. Test Configurations .............................................................................................................................................................................8 4. TEST RESULT ..................................................................................................................................................... 9 4.1. Radiated Emissions Measurement ......................................................................................................................................................9 4.2. Band Edge Emissions Measurement .................................................................................................................................................14 4.3. Antenna Requirements .....................................................................................................................................................................19 5. LIST OF MEASURING EQUIPMENTS ................................................................................................................... 20 6. MEASUREMENT UNCERTAINTY.......................................................................................................................... 21 APPENDIX A. TEST PHOTOS ........................................................................................................................ A1 ~ A2 Report Format Version: Rev. 01 Page No. : i of ii FCC ID: KA2IR885LA1 Issued Date :Nov. 21, 2016

Report No.: FR551807-06AB History of This Test Report REPORT NO. VERSION DESCRIPTION ISSUED DATE FR551807-06AB Rev. 01 Initial issue of report Nov. 21, 2016 36/52 14 5180 MHz 5260 MHz 42 50 42/50/58 5210 MHz 5250 MHz 42 5210 MHz 5.15~5.25 GHz 5.15-5.35 GHz 5.25-5.35 GHz 47 CFR FCC Part 15 Subpart E Ant. A + Ant. B Further, this requirement does not apply to intentional radiators that must be professionally installed. Report Format Version: Rev. 01 Page No. : ii of ii FCC ID: KA2IR885LA1 Issued Date :Nov. 21, 2016

spontom cas. Report No.: FR551807—06AB Project No: CB10507150 1. VERIFICATION OF COMPLIANCE Product Name AC3150 Ulfra Wi—Fi Router Brand Name D—Link Model No. DIR—88 5L. Applicant D—Link Corporation Test Rule Part(s) 47 CFR FCC Part 15 Subpart E §15.407 Sporton International as requested by the applicant to evaluate the EMC performance of the product sample received on May 11, 2015 would like to declare that the tested sample has been evaluated and found to be in compliance with the tested rule parts. The data recorded as well as the test configuration specified is frue and accurate for showing the sample‘s EMC nature. Sam Chen SPORTON INTERNATIONAL INC. Report Format Version: Rev. 01 Page No. : 1 of 21 FCC ID: KAZIREBSLA1 Issued Date : Nov. 21, 2016

Report No.: FR551807-06AB 2. SUMMARY OF THE TEST RESULT Applied Standard: 47 CFR FCC Part 15 Subpart E Part Rule Section Description of Test Result 4.1 15.407(b) Radiated Emissions Complies 4.2 15.407(b) Band Edge Emissions Complies 4.3 15.203 Antenna Requirements Complies Report Format Version: Rev. 01 Page No. : 2 of 21 FCC ID: KA2IR885LA1 Issued Date : Nov. 21, 2016

Report No.: FR551807-06AB 3. GENERAL INFORMATION 3.1. Product Details Items Description Product Type WLAN (4TX, 4RX) Radio Type Intentional Transceiver Power Type From power adapter Modulation IEEE 802.11a: OFDM IEEE 802.11n/ac: see the below table Data Modulation IEEE 802.11a/n: OFDM (BPSK / QPSK / 16QAM / 64QAM) IEEE 802.11ac: OFDM (BPSK / QPSK / 16QAM / 64QAM / 256QAM, 1024QAM) Data Rate (Mbps) IEEE 802.11a: OFDM (6/9/12/18/24/36/48/54) IEEE 802.11n/ac: see the below table Frequency Range 5150 ~ 5250 MHz / 5725 ~ 5850 MHz Channel Number 9 for 20MHz bandwidth ; 4 for 40MHz bandwidth 2 for 80MHz bandwidth Carrier Frequencies Please refer to section 3.4 Antenna Please refer to section 3.3 Items Description Communication Mode IP Based (Load Based) Frame Based Beamforming Function With beamforming Without beamforming Operate Condition Indoor Outdoor Note: The product has beamforming function for 801.11ac in 2.4GHz and 5GHz. Report Format Version: Rev. 01 Page No. : 3 of 21 FCC ID: KA2IR885LA1 Issued Date : Nov. 21, 2016

Report No.: FR551807-06AB Antenna and Band width Antenna Four (TX) Band width Mode 20 MHz 40 MHz 80 MHz IEEE 802.11a V X X IEEE 802.11n V V X IEEE 802.11ac V V V IEEE 11n/ac Spec. Number of Protocol Data Rate / MCS Transmit Chains (NTX) 802.11n (HT20) 4 MCS 0-31 802.11n (HT40) 4 MCS 0-31 802.11ac (VHT20) 4 MCS0-11/Nss1-4 802.11ac (VHT40) 4 MCS0-11/Nss1-4 802.11ac (VHT80) 4 MCS0-11/Nss1-4 Note 1: IEEE Std. 802.11n modulation consists of HT20 and HT40 (HT: High Throughput). Then EUT supports HT20 and HT40. Note 2: IEEE Std. 802.11ac modulation consists of VHT20, VHT40, VHT80 and VHT160 (VHT: Very High Throughput). Then EUT supports VHT20, VHT40 and VHT80. Note 3: Modulation modes consist of below configuration: HT20/HT40: IEEE 802.11n, VHT20/VHT40/VHT80: IEEE 802.11ac 3.2. Accessories Power Brand Model Rating Input:100-240V~50/60Hz 0.9A Max. Adapter APD WA-36A12R Output:12V-3A Report Format Version: Rev. 01 Page No. : 4 of 21 FCC ID: KA2IR885LA1 Issued Date : Nov. 21, 2016

Report No.: FR551807-06AB 3.3. Table for Filed Antenna Antenn Gain Cable Loss True Gain Antenna Ant. Brand Holder P/N Connector (dBi) (dBi) (dBi) Type 2.4G 5G 2.4G 5G 2.4G 5G HL TECHNOLOGY Dipole SMA Plug 1 290-20187 1.8 2.8 0.5 1 1.3 1.8 GROUP LIMITED Antenna Reverse HL TECHNOLOGY Dipole SMA Plug 2 290-20187 1.8 2.8 0.5 1 1.3 1.8 GROUP LIMITED Antenna Reverse HL TECHNOLOGY Dipole SMA Plug 3 290-20188 1.8 2.8 0.5 1 1.3 1.8 GROUP LIMITED Antenna Reverse HL TECHNOLOGY Dipole SMA Plug 4 290-20188 1.8 2.8 0.5 1 1.3 1.8 GROUP LIMITED Antenna Reverse HL TECHNOLOGY PCB 5 290-20213 I-PEX 1.3 - - - 1.3 - GROUP LIMITED Antenna Note: The EUT has five antennas. <For 2.4GHz Band> For IEEE 802.11b/g/n/ac mode (4TX/4RX) Chain 1, Chain 2, Chain 3 and Chain 4 could transmit/receive simultaneously. <For 5GHz Band > For IEEE 802.11a/n/ac mode (4TX/4RX): Chain 1, Chain 2, Chain 3 and Chain 4 could transmit/receive simultaneously. 2.4GHz: Chain 1 / Connect to Ant 1 5GHz: Chain 4 / Connect to Ant 1 2.4GHz: Chain 2 / Connect to Ant 3 5GHz: Chain 3 / Connect to Ant 3 2.4GHz: Chain 3 / Connect to Ant 4 5GHz: Chain 2 / Connect to Ant 4 5GHz: Chain 1 / Connect to Ant 2 2.4GHz: Chain 4 / Connect to Ant 5 Report Format Version: Rev. 01 Page No. : 5 of 21 FCC ID: KA2IR885LA1 Issued Date : Nov. 21, 2016

Report No.: FR551807-06AB 3.4. Table for Carrier Frequencies There are three bandwidth systems. For 20MHz bandwidth systems, use Channel 36, 40, 44, 48, 149, 153, 157, 161, 165. For 40MHz bandwidth systems, use Channel 38, 46, 151, 159. For 80MHz bandwidth systems, use Channel 42, 155. Frequency Band Channel No. Frequency Channel No. Frequency 36 5180 MHz 44 5220 MHz 5150~5250 MHz 38 5190 MHz 46 5230 MHz Band 1 40 5200 MHz 48 5240 MHz 42 5210 MHz - - 149 5745 MHz 157 5785 MHz 5725~5850 MHz 151 5755 MHz 159 5795 MHz Band 4 153 5765 MHz 161 5805 MHz 155 5775 MHz 165 5825 MHz 3.5. Table for Test Modes Preliminary tests were performed in different data rate to find the worst radiated emission. The data rate shown in the table below is the worst-case rate with respect to the specific test item. Investigation has been done on all the possible configurations for searching the worst cases. The following table is a list of the test modes shown in this test report. Test Items Mode Data Rate Channel Chain Radiated Emission Above 1GHz For Non-Beamforming mode 11a/BPSK Band 1 6Mbps 36 1+2+3+4 11ac VHT20 Band 4 MCS0/Nss1 165 1+2+3+4 Band Edge Emission For Non-Beamforming mode 11a/BPSK Band 1 6Mbps 36 1+2+3+4 11ac VHT20 Band 4 MCS0/Nss1 165 1+2+3+4 Note 1: VHT20 covers HT20, due to same modulation. Note 2: All the specification of test configurations and test modes were based on customer's request The following test modes were performed for all tests: For Radiated Emission test: The EUT can be placed in Y-axis and Z-axis. According to the original report, the worst case was found at Z-axis. So The measurement followed the same test mode. Mode 1. CTX - Place EUT in Z-axis Report Format Version: Rev. 01 Page No. : 6 of 21 FCC ID: KA2IR885LA1 Issued Date : Nov. 21, 2016

Report No.: FR551807-06AB 3.6. Table for Testing Locations Test Site Location Address: No.8, Lane 724, Bo-ai St., Jhubei City, Hsinchu County 302, Taiwan, R.O.C. TEL: 886-3-656-9065 FAX: 886-3-656-9085 FCC Test Site No. Site Category Location IC File No. VCCI Reg. No Designation No. 03CH01-CB SAC Hsin Chu TW0006 IC 4086D - Open Area Test Site (OATS); Semi Anechoic Chamber (SAC). 3.7. Table for Class II Change This product is an extension of original one reported under Sporton project number: FR551807AB and FR551807-05. Below is the table for the change of the product with respect to the original one. Modifications Performance Checking After evaluating, the worst case is found at 802.11a CH36 and 802.11ac MCS0/Nss1 VHT20 CH165 (For Non-Beamforming Mode) and retest these channels only. Updating the chip version from BCM4366B1 to The test item as below. BCM4366C0. 1. Radiated Emissions (Above 1GHz) 2. Emissions Measurement Note: The above test items will be based on original output power to re-test. 3.8. Table for Supporting Units For Test Site No: 03CH01-CB Support Unit Brand Model FCC ID Notebook DELL E4300 DoC 3.9. EUT Operation during Test The EUT was programmed to be in continuously transmitting mode. 3.10. Duty Cycle On Time On+Off Time Duty Cycle Duty Factor 1/T Minimum VBW Mode (ms) (ms) (%) (dB) (kHz) 802.11a 2.058 2.090 98.50 0.07 0.01 802.11ac MCS0/Nss1 VHT20 1.839 1.948 94.40 0.25 0.54 Report Format Version: Rev. 01 Page No. : 7 of 21 FCC ID: KA2IR885LA1 Issued Date : Nov. 21, 2016

Report No.: FR551807-06AB 3.11. Test Configurations 3.11.1. Radiation Emissions Test Configuration AC MAIN 1 2 EUT NB Item Connection Shielded Length 1 Power cable No 1.2m 2 RJ-45 cable No 10m Report Format Version: Rev. 01 Page No. : 8 of 21 FCC ID: KA2IR885LA1 Issued Date : Nov. 21, 2016

Report No.: FR551807-06AB 4. TEST RESULT 4.1. Radiated Emissions Measurement 4.1.1. Limit For transmitters operating in the 5.15-5.25 GHz band: all emissions outside of the 5.15-5.35 GHz band shall not exceed an e.i.r.p. of −27 dBm/MHz. For transmitters operating in the 5.725-5.85 GHz band: Follow 15.407(b)(4)(ii), the emission limits in § 15.247(d), 30dBc in any 100 kHz bandwidth outside the operating frequency band. In addition, In case the emission fall within the restricted band specified on 15.205(a), then the 15.209(a) limit in the table below has to be followed. Frequencies Field Strength Measurement Distance (MHz) (micorvolts/meter) (meters) 0.009~0.490 2400/F(kHz) 300 0.490~1.705 24000/F(kHz) 30 1.705~30.0 30 30 30~88 100 3 88~216 150 3 216~960 200 3 Above 960 500 3 4.1.2. Measuring Instruments and Setting Please refer to section 5 of equipments list in this report. The following table is the setting of spectrum analyzer and receiver. Spectrum Parameter Setting Attenuation Auto Start Frequency 1000 MHz Stop Frequency 40 GHz RBW / VBW (Emission in restricted band) 1MHz / 3MHz for Peak, 1MHz / 1/T for Average RBW / VBW (Emission in non-restricted band) 1MHz / 3MHz for peak Receiver Parameter Setting Attenuation Auto Start ~ Stop Frequency 9kHz~150kHz / RBW 200Hz for QP Start ~ Stop Frequency 150kHz~30MHz / RBW 9kHz for QP Start ~ Stop Frequency 30MHz~1000MHz / RBW 120kHz for QP Report Format Version: Rev. 01 Page No. : 9 of 21 FCC ID: KA2IR885LA1 Issued Date : Nov. 21, 2016

Report No.: FR551807-06AB 4.1.3. Test Procedures 1. Configure the EUT according to ANSI C63.10. The EUT was placed on the top of the turntable 1.5 meter above ground. The phase center of the receiving antenna mounted on the top of a height-variable antenna tower was placed 1m & 3m far away from the turntable. 2. Power on the EUT and all the supporting units. The turntable was rotated by 360 degrees to determine the position of the highest radiation. 3. The height of the broadband receiving antenna was varied between one meter and four meters above ground to find the maximum emissions field strength of both horizontal and vertical polarization. 4. For each suspected emissions, the antenna tower was scan (from 1 M to 4 M) and then the turntable was rotated (from 0 degree to 360 degrees) to find the maximum reading. 5. Set the test-receiver system to Peak or CISPR quasi-peak Detect Function with specified bandwidth under Maximum Hold Mode. 6. For emissions above 1GHz, use 1MHz VBW and 3MHz RBW for peak reading. Then 1MHz RBW and 1/T VBW for average reading in spectrum analyzer. 7. If the emissions level of the EUT in peak mode was 3 dB lower than the average limit specified, then testing will be stopped and peak values of EUT will be reported, otherwise, the emissions which do not have 3 dB margin will be repeated one by one using the quasi-peak method for below 1GHz. 8. For testing above 1GHz, the emissions level of the EUT in peak mode was lower than average limit (that means the emissions level in peak mode also complies with the limit in average mode), then testing will be stopped and peak values of EUT will be reported, otherwise, the emissions will be measured in average mode again and reported. 9. In case the emission is lower than 30MHz, loop antenna has to be used for measurement and the recorded data should be QP measured by receiver. High – Low scan is not required in this case. Report Format Version: Rev. 01 Page No. : 10 of 21 FCC ID: KA2IR885LA1 Issued Date : Nov. 21, 2016

Report No.: FR551807-06AB 4.1.4. Test Setup Layout 4.1.5. Test Deviation There is no deviation with the original standard. 4.1.6. EUT Operation during Test The EUT was programmed to be in continuously transmitting mode. Report Format Version: Rev. 01 Page No. : 11 of 21 FCC ID: KA2IR885LA1 Issued Date : Nov. 21, 2016

Report No.: FR551807-06AB 4.1.7. Results for Radiated Emissions (1GHz~40GHz) Temperature 25℃ Humidity 60% IEEE 802.11a CH 36 / Test Engineer Akina Chiu Configurations Chain 1 + Chain 2 + Chain 3 + Chain 4 Test Date Jul. 05, 2016 Horizontal Vertical Report Format Version: Rev. 01 Page No. : 12 of 21 FCC ID: KA2IR885LA1 Issued Date : Nov. 21, 2016

Report No.: FR551807-06AB Temperature 25℃ Humidity 60% IEEE 802.11ac MCS0/Nss1 VHT20 CH 165 / Test Engineer Akina Chiu Configurations Chain 1 + Chain 2 + Chain 3 + Chain 4 Test Date Jul. 05, 2016 Horizontal Vertical Note: The amplitude of spurious emissions that are attenuated by more than 20dB below the permissible value has no need to be reported. Emission level (dBuV/m) = 20 log Emission level (uV/m). Corrected Reading: Antenna Factor + Cable Loss + Read Level - Preamp Factor = Level. Report Format Version: Rev. 01 Page No. : 13 of 21 FCC ID: KA2IR885LA1 Issued Date : Nov. 21, 2016

Report No.: FR551807-06AB 4.2. Band Edge Emissions Measurement 4.2.1. Limit For transmitters operating in the 5.15-5.25 GHz band: all emissions outside of the 5.15-5.35 GHz band shall not exceed an e.i.r.p. of −27 dBm/MHz. For transmitters operating in the 5.725-5.85 GHz band: Follow 15.407(b)(4)(ii), the emission limits in § 15.247(d), 30dBc in any 100 kHz bandwidth outside the operating frequency band. In addition, In case the emission fall within the restricted band specified on 15.205(a), then the 15.209(a) limit in the table below has to be followed. Frequencies Field Strength Measurement Distance (MHz) (micorvolts/meter) (meters) 0.009~0.490 2400/F(kHz) 300 0.490~1.705 24000/F(kHz) 30 1.705~30.0 30 30 30~88 100 3 88~216 150 3 216~960 200 3 Above 960 500 3 4.2.2. Measuring Instruments and Setting Please refer to section 5 of equipments list in this report. The following table is the setting of the spectrum analyzer. Spectrum Parameter Setting Attenuation Auto Span Frequency 100 MHz RBW / VBW (Emission in restricted band) 1MHz / 3MHz for Peak, 1MHz / 1/T for Average RBW / VBW (Emission in non-restricted band) 1MHz / 3MHz for Peak RBW / VBW (30dBc in any 100 kHz bandwidth emission) 100 kHz / 300 kHz for Peak 4.2.3. Test Procedures For Radiated band edges Measurement: The test procedure is the same as section 4.1.3. For Radiated Emissions in non-restricted frequency bands Measurement: Test was performed in accordance with Clause 11.11 of ANSI C63.10-2013 and/or in Section 11.0 of KDB Publication 558074. Report Format Version: Rev. 01 Page No. : 14 of 21 FCC ID: KA2IR885LA1 Issued Date : Nov. 21, 2016

Report No.: FR551807-06AB 4.2.4. Test Setup Layout For Radiated band edges Measurement: This test setup layout is the same as that shown in section 4.1.4. For Radiated Emissions in non-restricted frequency bands Measurement: This test setup layout is the same as that shown in section 4.1.4. 4.2.5. Test Deviation There is no deviation with the original standard. 4.2.6. EUT Operation during Test The EUT was programmed to be in continuously transmitting mode. Report Format Version: Rev. 01 Page No. : 15 of 21 FCC ID: KA2IR885LA1 Issued Date : Nov. 21, 2016

Report No.: FR551807-06AB 4.2.7. Test Result of Band Edge and Fundamental Emissions Temperature 25℃ Humidity 60% IEEE 802.11a CH 36, 40, 48 / Test Engineer Akina Chiu Configurations Chain 1 + Chain 2 + Chain 3 + Chain 4 Test Date Jul. 05, 2016 Channel 36 Item 3, 4 are the fundamental frequency at 5180 MHz. Note: Emission level (dBuV/m) = 20 log Emission level (uV/m) Corrected Reading: Antenna Factor + Cable Loss + Read Level - Preamp Factor = Level Report Format Version: Rev. 01 Page No. : 16 of 21 FCC ID: KA2IR885LA1 Issued Date : Nov. 21, 2016

Report No.: FR551807-06AB For Radiated Emissions in non-restricted frequency bands Measurement Plot on Configuration IEEE 802.11ac MCS0/Nss1 VHT20 / Reference Level * RBW 100 kHz Marker 1 [T1 ] * VBW 300 kHz 106.69 dBµV Ref 117 dBµV * Att 10 dB SWT 40 ms 5.827497500 GHz Offset 10 dB 110 1 A 1 PK 100 VIEW LVL 90 80 70 60 3DB 50 40 30 20 Center 5.825 GHz 3 MHz/ Span 30 MHz Date: 5.JUL.2016 23:27:08 Plot on Configuration IEEE 802.11ac MCS0/Nss1 VHT20 / CH 165 / 30MHz~5725MHz (down 30dBc) * RBW 100 kHz Marker 1 [T1 ] * VBW 300 kHz 52.56 dBµV Ref 117 dBµV * Att 10 dB SWT 580 ms 523.329375000 MHz Offset 10 dB 110 A 1 PK 100 VIEW LVL 90 80 D1 76.69 dBµV 70 60 3DB 1 50 40 30 20 Start 30 MHz 569.5 MHz/ Stop 5.725 GHz Date: 5.JUL.2016 23:28:27 Report Format Version: Rev. 01 Page No. : 17 of 21 FCC ID: KA2IR885LA1 Issued Date : Nov. 21, 2016

Report No.: FR551807-06AB Plot on Configuration IEEE 802.11ac MCS0/Nss1 VHT20 / CH 165 / 5850MHz~40000MHz (down 30dBc) * RBW 100 kHz Marker 1 [T1 ] * VBW 300 kHz 61.31 dBµV Ref 117 dBµV * Att 10 dB SWT 3.5 s 39.252968750 GHz Offset 10 dB 110 A 1 PK 100 VIEW LVL 90 80 D1 76.69 dBµV 70 1 60 3DB 50 40 30 20 Start 5.85 GHz 3.415 GHz/ Stop 40 GHz Date: 5.JUL.2016 23:29:06 Report Format Version: Rev. 01 Page No. : 18 of 21 FCC ID: KA2IR885LA1 Issued Date : Nov. 21, 2016

Report No.: FR551807-06AB 4.3. Antenna Requirements 4.3.1. Limit Except for special regulations, the Low-power Radio-frequency Devices must not be equipped with any jacket for installing an antenna with extension cable. An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this Section. The manufacturer may design the unit so that the user can replace a broken antenna, but the use of a standard antenna jack or electrical connector is prohibited. Further, this requirement does not apply to intentional radiators that must be professionally installed. 4.3.2. Antenna Connector Construction Please refer to section 3.3 in this test report; antenna connector complied with the requirements. Report Format Version: Rev. 01 Page No. : 19 of 21 FCC ID: KA2IR885LA1 Issued Date : Nov. 21, 2016

Report No.: FR551807-06AB 5. LIST OF MEASURING EQUIPMENTS Calibration Instrument Manufacturer Model No. Serial No. Characteristics Remark Date Radiation Horn Antenna EMCO 3115 00075790 750MHz ~ 18GHz Oct. 22, 2015 (03CH01-CB) Radiation Horn Antenna Schwarzbeck BBHA 9170 BBHA9170252 15GHz ~ 40GHz Jul. 21, 2015 (03CH01-CB) Radiation Pre-Amplifier Agilent 8449B 3008A02310 1GHz ~ 26.5GHz Jan. 18, 2016 (03CH01-CB) Radiation Pre-Amplifier WM TF-130N-R1 923365 26GHz ~ 40GHz Nov. 13, 2015 (03CH01-CB) Radiation Spectrum Analyzer R&S FSP40 100056 9kHz ~ 40GHz Oct. 27, 2015 (03CH01-CB) Radiation RF Cable-high Woken High Cable-16 N/A 1 GHz ~ 18 GHz Nov. 02, 2015 (03CH01-CB) Radiation RF Cable-high Woken High Cable-17 N/A 1 GHz ~ 18 GHz Nov. 02, 2015 (03CH01-CB) Radiation RF Cable-high Woken High Cable-40G-1 N/A 18GHz ~ 40 GHz Nov. 02, 2015 (03CH01-CB) Radiation RF Cable-high Woken High Cable-40G-2 N/A 18GHz ~ 40 GHz Nov. 02, 2015 (03CH01-CB) Radiation Test Software Audix E3 6.2009-l0-7 N/A N/A (03CH01-CB) Note: Calibration Interval of instruments listed above is one year. Report Format Version: Rev. 01 Page No. : 20 of 21 FCC ID: KA2IR885LA1 Issued Date : Nov. 21, 2016

Report No.: FR551807-06AB 6. MEASUREMENT UNCERTAINTY Test Items Uncertainty Remark Radiated Emission (1GHz ~ 18GHz) 3.7 dB Confidence levels of 95% Radiated Emission (18GHz ~ 40GHz) 3.5 dB Confidence levels of 95% Report Format Version: Rev. 01 Page No. : 21 of 21 FCC ID: KA2IR885LA1 Issued Date : Nov. 21, 2016


Document Created: 2017-12-20 00:00:56
Document Modified: 2017-12-20 00:00:56
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC