SAR Report Part 3

FCC ID: KA2DWLG132A1

RF Exposure Info

Download: PDF
FCCID_478341

Schmid & Partner Engineering AG § 6 & Zeughausstrasse 43, 8004 Zurich, Switzerland Phone +41 1 245 9700, Fax +41 1 245 9779 info@speag.com, http;/\www.speag.com DASY Dipole Validation Kit Type: D2450V2 Serial: 716 Manufactured: September 10, 2002 Calibrated: August 23, 2004

4 Measurement Conditions The measurements were performed in the quarter size flat phantom filled with head simulating solution ofthe following electrical parameters at 2450 MHz: Relative Diclectricity 38.3 + 5% Conductivity 1.86 mho/m £5% The DASY4 System with a dosimetric E—field probe ES3DV2 (SN:3025, Conversion factor 4.55 at 2450 MHz) was used for the measurements. The dipole was mounted on the small tripod so thatthe dipole feedpoint was positioned below the center marking of the quarter size flat phantom and the dipole was oriented parallel to the body axis (the long side ofthe phantom). The standard measuring distance was 10mm from dipole center to the solution surface. Lossless spacer was used during measurements for accurate distance positioning. The coarse grid with a grid spacing of 15mm was aligned with the dipole. The 7x7x7 fine cube was chosen for cube integration. The dipole input power (forward power) was 250mW + 3 %. The results are normalized to 1 W input power. 2 SAR Measurement with DASY4 System Standard SAR—measurements were performed according to the measurement conditions described in section 1. The results (see figure supplied) have been normalized to a dipole input power of 1 W (forward power). The resulting averaged SAR—values measured with the dosimetric probe ES3DV2 SN:3025 and applying the advanced extrapolation are: averaged over 1 om‘ (1 g) of tissue: 52.4 mWig + 16.8 % (k:2)' averaged over 10 cm‘ (10 g) of tissue: 23.8 mWig + 16.2 % (k:72)l ‘ validation uncertainty

3. Dipole Impedance and Return Loss The impedance was measured at the SMA—connector with a network analyzer and numerically transformed to the dipole feedpoint. The transformation parameters from the SMA—connector to the dipole feedpoint are: Electrical delay: 1.147 ns (one direction) Transmission factor: 0.983 (voltage transmission, one direction) The dipole was positioned at the flat phantom sections according to section 1 and the distance spacer was in place during impedance measurements. Feedpoint impedance at 2450 MHz: Re{Z} = 54.7 0 Im {Z} =2.7 0 Return Loss at 2450 MHz —26.1 dB 4. Measurement Conditions The measurements were performed in the quarter size flat phantom filled with body simulating solution of the following electrical parameters at 2450 MHz: Relative Dielectricity 51.7 +5% Conductivity 1.96 mho/m £5% The DASY4 System with a dosimetric E—field probe ES3DV2 (SN:3025, Conversion factor 4.22 at 2450 MHz) was used for the measurements. The dipole was mounted on the small tripod so that the dipole feedpoint was positioned below the center marking of the quarter size flat phantom and the dipole was oriented parallelto the body axis (the long side of the phantom). The standard measuring distance was 10mm from dipole center to the solution surface. Lossless spacer was used during measurements for accurate distance positioning. The coarse grid with a grid spacing of 15mm was aligned with the dipole. The 7x7x7 fine cube was chosen for cube integration. The dipole input power (forward power) was 250mW +3 %. The results are normalized to 1 W input power.

5. SAR Measurement with DASY4 System Standard SAR—measurements were performed according to the measurement conditions described in section 4. The results (see figure supplied) have been normalized to a dipole input power of I W (forward power). The resulting averaged SAR—values measured with the dosimetric probe ES3DV2 SN:3025 and applying the advanced extrapolation are: averaged over 1 em‘ (1 g) of tissue: 48.8 mW/g + 16.8 % (&2) averaged over 10 em‘ (10 g) of tissue: 22.6 mWig + 16.2 % (IFZ)Z 6. Dipole Impedance and Return Loss The dipole was positioned at the flat phantom sections according to section 4 and the distance spacer was in place during impedance measurements. Feedpoint impedance at 2450 MHz: Re{Z} = 50.8 0 Im {Z} = 4.1 0 Return Loss at 2450 MHz —27.1 dB 7 Handling Do not apply excessive force to the dipole arms, because they might bend. Bending ofthe dipole arms stresses the soldered connections near the feedpoint leading to a damage ofthe dipole. 8. Design The dipole is made ofstandard semirigid coaxial cable. The center conductor ofthe feeding line is directly connected to the second arm ofthe dipole. The antennais therefore short—circuited for DC— signals. Small end caps have been added to the dipole arms in order to improve matching when loaded according to the position as explained in Sections land 4. The SAR data are not affected bythis change. The overall dipole length is still according to the Standard. 9. Power Test After long term use with 40W radiated power, only a slight warming of the dipole near the feedpoint can be measured. * validation uncertainty

Page 1 of 1 Date/Time: 08/20/04 14:48:41 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN716 Communication System: CW—2450; Frequency: 2450 MHz;Duty Cycle: 1:1 Medium: HSL 2450 MHz; Medium parameters used: f= 2450 MHz; 0 = 1.86 mho/m; &, = 38.3; p = 1000 kg/m> Phantom section: Flat Section Measurement Standard: DASY4 (High Precision Assessment) DASY4 Configuration: * Probe: ES3DV2 — SN3025; ConvF(4.55, 4.55, 4.55); Calibrated: 9/29/2003 Sensor—Surface: 4mm (Mechanical Surface Detection) e e e e Electronics: DAE4 Sn601; Calibrated: 7/22/2004 Phantom: Flat Phantom quarter size; Type: QDO0OPS50AA; Serial: SN:1001; Measurement SW: DASY4, V4.3 Build 16; Postprocessing SW: SEMCAD, V1.8 Build 123 Pin = 250 mW; d = 10 mm/Area Scan (81x81x1): Measurement grid: dx=1 5mm, dy=1 5mm Maximum value of SAR (interpolated) = 14.9 mW/g Pin = 250 mW; d = 10 mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=Smm, dz=5mm Reference Value =91.1 V/m; Power Drift =0.1 dB Peak SAR (extrapolated) = 27.6 W/kg SAR(I g) = 13.1 mWig; SAR(10 g) = 5.95 mWig Maximum value of SAR (measured) = 14.8 mW/g dB 0 dB = 14.8mW/g

TL Veaoct 20 hug 2004 14:02:08 CH® sn i uors 4:54.670 0 267970 474.08 pH 2 450.000 000 MHz bei by 16 cH2 CeNTeR 2 450.008 000 MHz SPaN 402.000 008 Mitz

Page 1 of 1 Date/Time: 08/23/04 11:02:14 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN716 Communication System: CW—2450; Frequency: 2450 MHz;Duty Cycle:1: 1 Medium: Muscle 2450 MHz; Medium parameters used: £= 2450 MHz; 0 = 1.96 mho/m; &, = 51.7; p= 1000 kg/m? Phantom section: Flat Section Measurement Standard: DASY4 (High Precision Assessment) DASY4 Configuration: e Probe: ES3DV2 — SN3025; ConvF(4.22,4.22, 4.22); Calibrated: 9/29/2003 Sensor—Surface: 4mm (Mechanical Surface Detection) Electronics: DAE4 Sn601; Calibrated: 7/22/2004 Phantom: Flat Phantom quarter size; Type: QDO0OP50AA; Serial: SN:1001; Measurement SW: DASY4, V4.3 Build 17; Postprocessing SW: SEMCAD, V1.8 Build 124 Pin = 250 mW; d = 10 mm/Area Scan (81x81x1): Measurement grid: dx=15mm, dy=1 5mm Maximum value of SAR (interpolated) = 14.2 mW/g Pin = 250 mW; d = 10 mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=Smm, dz=Smm Reference Value = 85.8 V/m; Power Drift = 0.0 dB Peak SAR (extrapolated) = 24.9 W/kg SAR(I g) = 12.2 mWig; SAR(10 g) = 5.64 mWig Maximum value of SAR (measured) = 14.1 mW/g dB 0 dB = 14.ImW/g

T6 "RBody 23 fMug 2004 ©B:51:35 CHI sit 1 U FS 4 50.024 a 4.0040 n 265.30 pH 2 450.000 000 MHz Del tor y Av 159 CH2 center 2 450.000 000 lMHz sPaN 400.000 006 MHz

A3 : SYSTEM VALIDATION Date/Time: 10/01/04 11:54:39 Test Laboratory: Advance Data Technology System Validation Check-MSL 2450MHz DUT: Dipole 2450 MHz ; Type: D2450V2 ; Test Channel Frequency: 2450 MHz Communication System: CW ; Frequency: 2450 MHz; Duty Cycle: 1:1; Modulation type: CW Medium: MSL2450;Medium parameters used: f = 2450 MHz; σ = 2 mho/m; εr = 50.7; ρ = 1000 kg/m3 ; Liquid level : 155mm Phantom section: Flat Section ; Separation distance : 10 mm (The feetpoint of the dipole to the Phantom)Air temp. : 22.0 degrees ; Liquid temp. : 21.0 degrees DASY4 Configuration: - Probe: ET3DV6 - SN1687 ; ConvF(4.23, 4.23, 4.23) ; Calibrated: 2004/8/26 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn510; Calibrated: 2004/8/17 - Phantom: SAM 12; Type: SAM V4.0; Serial: TP 1202 - Measurement SW: DASY4, V4.3 Build 22; Postprocessing SW: SEMCAD, V1.8 Build 127 d=10mm, Pin=250mW/Area Scan (5x6x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 12.1 mW/g d=10mm, Pin=250mW/Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 87.3 V/m; Power Drift = -0.1 dB Peak SAR (extrapolated) = 27.4 W/kg SAR(1 g) = 12 mW/g; SAR(10 g) = 5.44 mW/g Maximum value of SAR (measured) = 13.6 mW/g


Document Created: 2004-10-07 14:52:50
Document Modified: 2004-10-07 14:52:50
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC