Test Report Co-Located Original

FCC ID: KA2BA2620PA1

Test Report

Download: PDF
FCCID_4376758

FCC Test Report (Co-Located) Report No.: RF170801C12-2 FCC ID: KA2WL6620APSA1 Test Model: DWL-6620APS Received Date: Aug. 01, 2017 Test Date: Oct. 12, 2017 Issued Date: Oct. 17, 2017 Applicant: D-Link Corporation Address: 17595 Mt. Herrmann, Fountain Valley, California, United States, 92708 Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. Test Location: No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, TAIWAN (R.O.C.) FCC Registration / 788550 / TW0003 Designation Number: This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF170801C12-2 Page No. 1 / 32 Report Format Version: 6.1.1

Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity...................................................................................................................... 4 2 Summary of Test Results ..................................................................................................................... 5 2.1 Measurement Uncertainty ................................................................................................................... 5 2.2 Modification Record ............................................................................................................................ 5 3 General Information .............................................................................................................................. 6 3.1 General Description of EUT ................................................................................................................ 6 3.2 Description of Test Modes ................................................................................................................... 8 3.2.1 Test Mode Applicability and Tested Channel Detail ........................................................................... 10 3.3 Description of Support Units ............................................................................................................. 12 3.3.1 Configuration of System under Test .................................................................................................. 12 3.4 General Description of Applied Standards ........................................................................................ 13 4 Test Types and Results ...................................................................................................................... 14 4.1 Radiated Emission and Bandedge Measurement............................................................................. 14 4.1.1 Limits of Radiated Emission and Bandedge Measurement .............................................................. 14 4.1.2 Test Instruments ................................................................................................................................ 15 4.1.3 Test Procedures................................................................................................................................. 16 4.1.4 Deviation from Test Standard ............................................................................................................ 16 4.1.5 Test Setup .......................................................................................................................................... 17 4.1.6 EUT Operating Conditions................................................................................................................. 18 4.1.7 Test Results ....................................................................................................................................... 19 4.2 Conducted Emission Measurement .................................................................................................. 23 4.2.1 Limits of Conducted Emission Measurement .................................................................................... 23 4.2.2 Test Instruments ................................................................................................................................ 23 4.2.3 Test Procedures................................................................................................................................. 24 4.2.4 Deviation from Test Standard ............................................................................................................ 24 4.2.5 Test Setup .......................................................................................................................................... 24 4.2.6 EUT Operating Conditions................................................................................................................. 24 4.2.7 Test Results ....................................................................................................................................... 25 5 Pictures of Test Arrangements .......................................................................................................... 31 Appendix – Information on the Testing Laboratories ................................................................................ 32 Report No.: RF170801C12-2 Page No. 2 / 32 Report Format Version: 6.1.1

Release Control Record Issue No. Description Date Issued RF170801C12-2 Original release. Oct. 17, 2017 Report No.: RF170801C12-2 Page No. 3 / 32 Report Format Version: 6.1.1

1 Certificate of Conformity Product: Unified AC Concurrent Dual-band PoE Access Point Brand: D-Link Corporation Test Model: DWL-6620APS Sample Status: Identical Prototype Applicant: D-Link Corporation Test Date: Oct. 12, 2017 Standards: 47 CFR FCC Part 15, Subpart C (Section 15.247) 47 CFR FCC Part 15, Subpart E (Section 15.407) ANSI C63.10-2013 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s RF characteristics under the conditions specified in this report. Prepared by : , Date: Oct. 17, 2017 Celine Chou / Specialist Approved by : , Date: Oct. 17, 2017 Ken Liu / Senior Manager Report No.: RF170801C12-2 Page No. 4 / 32 Report Format Version: 6.1.1

2 Summary of Test Results Applied 47 CFR FCC Part 15, Subpart C (Section 15.247) Standard: 47 CFR FCC Part 15, Subpart E (Section 15.407) FCC Test Item Result Remarks Clause Meet the requirement of limit. 15.207 AC Power Conducted Emission Pass Minimum passing margin is -15.26dB 15.407(b)(6) at 0.15000MHz. 15.205 / 15.209 / Meet the requirement of limit. 15.247(d) Radiated Emissions Pass Minimum passing margin is -2.5dB at 15.407(b) 365.62MHz. (1/2/3/4(i/ii)/6) 2.1 Measurement Uncertainty Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2: Expanded Uncertainty Measurement Frequency (k=2) (±) Conducted Emissions at mains ports 150kHz ~ 30MHz 2.94 dB 30MHz ~ 200MHz 3.59 dB Radiated Emissions up to 1 GHz 200MHz ~1000MHz 3.60 dB 1GHz ~ 18GHz 2.29 dB Radiated Emissions above 1 GHz 18GHz ~ 40GHz 2.29 dB 2.2 Modification Record There were no modifications required for compliance. Report No.: RF170801C12-2 Page No. 5 / 32 Report Format Version: 6.1.1

3 General Information 3.1 General Description of EUT Product Unified AC Concurrent Dual-band PoE Access Point Brand D-Link Corporation Test Model DWL-6620APS Status of EUT Identical Prototype 12Vdc from adapter Power Supply Rating 53Vdc from POE CCK, DQPSK, DBPSK for DSSS Modulation Type 256QAM, 64QAM, 16QAM, QPSK, BPSK for OFDM Modulation Technology DSSS, OFDM 802.11b:11/5.5/2/1Mbps 802.11a/g: 54/48/36/24/18/12/9/6Mbps Transfer Rate 802.11n: up to 300Mbps 802.11ac: up to 867Mbps 2.4GHz: 2412 ~ 2462MHz Operating Frequency 5.0GHz: 5180 ~ 5240MHz, 5745 ~ 5825MHz 2412 ~ 2462MHz: 11 for 802.11b, 802.11g, 802.11n (HT20) 7 for 802.11n (HT40) 5180 ~ 5240MHz: 4 for 802.11a, 802.11n (HT20), 802.11ac (VHT20) Number of Channel 2 for 802.11n (HT40), 802.11ac (VHT40) 1 for 802.11ac (VHT80) 5745 ~ 5825MHz: 5 for 802.11a, 802.11n (HT20), 802.11ac (VHT20) 2 for 802.11n (HT40), 802.11ac (VHT40) 1 for 802.11ac (VHT80) CDD Mode: 2412 ~ 2462MHz: 589.448mW 5180 ~ 5240MHz: 605.902mW 5745 ~ 5825MHz: 772.808mW Output Power Beamforming Mode: 2412 ~ 2462MHz: 283.832mW 5180 ~ 5240MHz: 302.972mW 5745 ~ 5825MHz: 386.430mW Antenna Type Refer to Note Antenna Connector Refer to Note Accessory Device Adapter Data Cable Supplied NA Report No.: RF170801C12-2 Page No. 6 / 32 Report Format Version: 6.1.1

Note: 1. The EUT incorporates a MIMO function. Physically, the EUT provides 2 completed transmitters and 2 receivers. Band Modulation Mode Beamforming Mode TX Function 802.11b Not Support 2TX 802.11g Not Support 2TX 2.4GHz 802.11n (HT20) Support 2TX 802.11n (HT40) Support 2TX 802.11a Not Support 2TX 802.11n (HT20) Support 2TX 802.11n (HT40) Support 2TX 5GHz 802.11ac (VHT20) Support 2TX 802.11ac (VHT40) Support 2TX 802.11ac (VHT80) Support 2TX * For 802.11n, CDD mode is the worst case for final radiated emission and power line conducted emission tests after pretesting CDD mode and beamforming mode. 2. The EUT uses following antennas. Gain (dBi) Type Connector 2.4GHz 5GHz Smart Antenna I-pex 4.90 6.10 3. The EUT consumes power from the following adapters and POE. (POE for support unit only) Adapter 1 Brand D-Link Model AMS115-1202000FU Input Power 100-240Vac, 50-60Hz, 0.8A Output Power 12Vdc, 2A Power Line 1.2m power cable without core attached on adapter Adapter 2 Brand D-Link Model WA-24Q12R Input Power 100-240Vac, 50-60Hz, 0.7A Output Power 12Vdc, 2A Power Line 1.2m power cable without core attached on adapter POE Brand D-Link Model PGS-1210-10P Input Power 100-240Vac Output Power 53Vdc Report No.: RF170801C12-2 Page No. 7 / 32 Report Format Version: 6.1.1

3.2 Description of Test Modes For 2.4GHz 11 channels are provided for 802.11b, 802.11g and 802.11n (HT20): Channel Frequency Channel Frequency 1 2412MHz 7 2442MHz 2 2417MHz 8 2447MHz 3 2422MHz 9 2452MHz 4 2427MHz 10 2457MHz 5 2432MHz 11 2462MHz 6 2437MHz 7 channels are provided for 802.11n (HT40): Channel Frequency Channel Frequency 3 2422MHz 7 2442MHz 4 2427MHz 8 2447MHz 5 2432MHz 9 2452MHz 6 2437MHz For 5180~5240MHz: 4 channels are provided for 802.11a, 802.11n (HT20), 802.11ac (VHT20): Channel Frequency Channel Frequency 36 5180 MHz 44 5220 MHz 40 5200 MHz 48 5240 MHz 2 channels are provided for 802.11n (HT40), 802.11ac (VHT40): Channel Frequency Channel Frequency 38 5190 MHz 46 5230 MHz 1 channel is provided for 802.11ac (VHT80): Channel Frequency 42 5210MHz Report No.: RF170801C12-2 Page No. 8 / 32 Report Format Version: 6.1.1

5745~5825MHz: 5 channels are provided for 802.11a, 802.11n (HT20), 802.11ac (VHT20): Channel Frequency Channel Frequency 149 5745MHz 161 5805MHz 153 5765MHz 165 5825MHz 157 5785MHz 2 channels are provided for 802.11n (HT40), 802.11ac (VHT40): Channel Frequency Channel Frequency 151 5755MHz 159 5795MHz 1 channel is provided for 802.11ac (VHT80): Channel Frequency 155 5775MHz Report No.: RF170801C12-2 Page No. 9 / 32 Report Format Version: 6.1.1

3.2.1 Test Mode Applicability and Tested Channel Detail EUT Configure Applicable to Description Mode RE1G RE<1G PLC A √ √ √ Power from adapter 1 B - √ √ Power from adapter 2 C - √ √ Power from POE RE1G: Radiated Emission above 1GHz & Where RE<1G: Radiated Emission below 1GHz Bandedge Measurement PLC: Power Line Conducted Emission Note: 1. The EUT had been pre-tested on the positioned of each 3 axis. The worst case was found when positioned on X-plane. 2. “-” means no effect. Radiated Emission Test (Above 1GHz): Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Modulation Configure Mode Freq. Range (MHz) Available Channel Tested Channel Technology Mode 802.11n (HT20) + 2412 ~ 2462 1 to 11 BPSK A 6 + 40 802.11n (HT20) 5180 ~ 5240 36 to 48 OFDM Radiated Emission Test (Below 1GHz): Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Modulation Configure Mode Freq. Range (MHz) Available Channel Tested Channel Technology Mode 802.11n (HT20) + 2412 ~ 2462 1 to 11 BPSK A, B, C 6 + 40 802.11n (HT20) 5180 ~ 5240 36 to 48 OFDM Power Line Conducted Emission Test: Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Modulation Configure Mode Freq. Range (MHz) Available Channel Tested Channel Technology Mode 802.11n (HT20) + 2412 ~ 2462 1 to 11 BPSK A, B, C 6 + 40 802.11n (HT20) 5180 ~ 5240 36 to 48 OFDM Report No.: RF170801C12-2 Page No. 10 / 32 Report Format Version: 6.1.1

Test Condition: Applicable to Environmental Conditions Input Power Tested by RE1G 25 deg. C, 66% RH 120Vac, 60Hz Chris Lin 120Vac, 60Hz RE<1G 25 deg. C, 66% RH Chris Lin 53Vdc 120Vac, 60Hz PLC 25 deg. C, 65% RH Chris Lin 53Vdc Report No.: RF170801C12-2 Page No. 11 / 32 Report Format Version: 6.1.1

3.3 Description of Support Units The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. ID Product Brand Model No. Serial No. FCC ID Remarks A. Notebook DELL E5410 6RP2YM1 FCC DoC Approved - B. Load NA NA NA NA - C. POE D-Link PGS-1210-10P NA NA Provided by manufacturer Note: 1. All power cords of the above support units are non-shielded (1.8m). 2. Item A acted as a communication partner to transfer data. Shielding ID Descriptions Qty. Length (m) Cores (Qty.) Remarks (Yes/No) 1. RJ45, Cat5e 1 3 N 0 - 2. RJ45, Cat5e 2 1.8 N 0 - 3. RJ45, Cat5e 1 1.8 N 0 - 3.3.1 Configuration of System under Test Adapter Mode EUT (2) Load (B) Adapter (EUT) (1) Remote site Notebook (A) POE Mode EUT (2) Load (B) (1) Remote site (3) POE (C) Notebook (A) Report No.: RF170801C12-2 Page No. 12 / 32 Report Format Version: 6.1.1

3.4 General Description of Applied Standards The EUT is a RF Product. According to the specification of the EUT declared by the manufacturer, it must comply with the requirements of the following standards: FCC Part 15, Subpart C (15.247) FCC Part 15, Subpart E (15.407) ANSI C63.10-2013 All test items have been performed and recorded as per the above standards. Report No.: RF170801C12-2 Page No. 13 / 32 Report Format Version: 6.1.1

4 Test Types and Results 4.1 Radiated Emission and Bandedge Measurement 4.1.1 Limits of Radiated Emission and Bandedge Measurement Radiated emissions which fall in the restricted bands must comply with the radiated emission limits specified as below table. Other emissions shall be at least 20dB below the highest level of the desired power: Frequencies (MHz) Field Strength (microvolts/meter) Measurement Distance (meters) 0.009 ~ 0.490 2400/F(kHz) 300 0.490 ~ 1.705 24000/F(kHz) 30 1.705 ~ 30.0 30 30 30 ~ 88 100 3 88 ~ 216 150 3 216 ~ 960 200 3 Above 960 500 3 Note: 1. The lower limit shall apply at the transition frequencies. 2. Emission level (dBuV/m) = 20 log Emission level (uV/m). 3. For frequencies above 1000MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20dB under any condition of modulation. Limits of unwanted emission out of the restricted bands Applicable To Limit 789033 D02 General UNII Test Procedure Field Strength at 3m New Rules v02r01 PK: 74 (dBµV/m) AV: 54 (dBµV/m) Equivalent Field Strength at Frequency Band Applicable To EIRP Limit 3m 5150~5250 MHz 15.407(b)(1) 5250~5350 MHz 15.407(b)(2) PK: -27 (dBm/MHz) PK: 68.2(dBµV/m) 5470~5725 MHz 15.407(b)(3) PK: -27 (dBm/MHz) *1 PK: 68.2(dBµV/m) *1 *2 PK: 10 (dBm/MHz) PK: 105.2 (dBµV/m) *2 15.407(b)(4)(i) *3 5725~5850 MHz PK: 15.6 (dBm/MHz) PK: 110.8(dBµV/m) *3 *4 PK: 27 (dBm/MHz) PK: 122.2 (dBµV/m) *4 15.407(b)(4)(ii) Emission limits in section 15.247(d) *2 *1 below the band edge increasing linearly to 10 beyond 75 MHz or more above of the band edge. dBm/MHz at 25 MHz above. *3 below the band edge increasing linearly to a level *4 from 5 MHz above or below the band edge of 15.6 dBm/MHz at 5 MHz above. increasing linearly to a level of 27 dBm/MHz at the band edge. Note: The following formula is used to convert the equipment isotropic radiated power (eirp) to field strength: 1000000 30 P E= µV/m, where P is the eirp (Watts). 3 Report No.: RF170801C12-2 Page No. 14 / 32 Report Format Version: 6.1.1

4.1.2 Test Instruments Description & Model No. Serial No. Cal. Date Cal. Due Manufacturer Test Receiver N9038A MY55420137 Mar. 27, 2017 Mar. 26, 2018 KEYSIGHT Spectrum Analyzer FSP40 100269 May. 11, 2017 May. 10, 2018 ROHDE & SCHWARZ BILOG Antenna VULB9168 9168-148 Dec. 28, 2016 Dec. 27, 2017 SCHWARZBECK HORN Antenna BBHA 9120 D 9120D-1169 Dec. 27, 2016 Dec. 26, 2017 SCHWARZBECK HORN Antenna BBHA 9170 BBHA9170241 Dec. 14, 2016 Dec. 13, 2017 SCHWARZBECK Loop Antenna EM-6879 269 Aug. 11, 2017 Aug. 10, 2018 EMCI Preamplifier 8449B 3008A01638 Feb. 22, 2017 Feb. 21, 2018 Agilent Preamplifier 8447D 2944A10638 Aug. 08, 2017 Aug. 07, 2018 Agilent RF signal cable CABLE-CH9-02 SUCOFLEX 104 Aug. 08, 2017 Aug. 07, 2018 HUBER+SUHNER (248780+MY13377) RF signal cable SUCOFLEX 104 CABLE-CH9-(250795/4) Aug. 08, 2017 Aug. 07, 2018 HUBER+SUHNER RF signal cable 8D-FB Cable-CH9-01 Aug. 01, 2017 Jul. 31, 2018 Woken Software ADT_Radiated_ NA NA NA BV ADT V7.6.15.9.4 Antenna Tower 2070/2080 512.835.4684 NA NA EMCO Turn Table 2087-2.03 NA NA NA EMCO Antenna Tower &Turn AT100 AT93021705 NA NA BV ADT Turn Table TT100 TT93021705 NA NA BV ADT Turn Table Controller SC100 SC93021705 NA NA BV ADT 26GHz ~ 40GHz Amplifier EM26400 815221 Oct. 17, 2016 Oct. 16, 2017 Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Chamber 9. 3. The horn antenna and preamplifier (model: 8449B) are used only for the measurement of emission frequency above 1GHz if tested. 4. The FCC Designation Number is TW0003. The number will be varied with the Lab location and scope as attached. 5. The IC Site Registration No. is IC 7450F-9. Report No.: RF170801C12-2 Page No. 15 / 32 Report Format Version: 6.1.1

4.1.3 Test Procedures For Radiated emission below 30MHz a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter chamber room. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. Both X and Y axes of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to Quasi-Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. Note: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 9kHz at frequency below 30MHz. For Radiated emission above 30MHz a. The EUT was placed on the top of a rotating table 0.8 meters (for 30MHz ~ 1GHz) / 1.5 meters (for above 1GHz) above the ground at 3 meter chamber room for test. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The height of antenna is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to quasi-peak detect function and specified bandwidth with maximum hold mode when the test frequency is below 1 GHz. f. The test-receiver system was set to peak and average detect function and specified bandwidth with maximum hold mode when the test frequency is above 1 GHz. If the peak reading value also meets average limit, measurement with the average detector is unnecessary. Note: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for Quasi-peak detection (QP) at frequency below 1GHz. 2. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is 3 MHz for Peak detection (PK) at frequency above 1GHz. 3. The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and the video bandwidth is ≥ 1/T (Duty cycle < 98%) or 10Hz (Duty cycle ≥ 98%) for Average detection (AV) at frequency above 1GHz. 4. All modes of operation were investigated and the worst-case emissions are reported. 4.1.4 Deviation from Test Standard No deviation. Report No.: RF170801C12-2 Page No. 16 / 32 Report Format Version: 6.1.1

4.1.5 Test Setup For Radiated emission below 30MHz 1m EUT& 3m Support Units Turn Table 80cm Ground Plane Test Receiver For Radiated emission 30MHz to 1GHz Ant. Tower 1-4m Variable 3m 10m EUT& Support Units Turn Table 80cm Ground Plane Test Receiver Report No.: RF170801C12-2 Page No. 17 / 32 Report Format Version: 6.1.1

For Radiated emission above 1GHz Ant. Tower 1-4m Variable EUT& 3m Support Units Turn Table Absorber 150cm Ground Plane Test Receiver For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.1.6 EUT Operating Conditions a. Placed the EUT on the testing table. b. Prepared a notebook to act as a communication partner and placed it outside of testing area. c. The communication partner connected with EUT via a RJ45 cable and ran a test program (provided by manufacturer) to enable EUT under transmission condition continuously at specific channel frequency. d. The communication partner sent data to EUT by command "PING". Report No.: RF170801C12-2 Page No. 18 / 32 Report Format Version: 6.1.1

4.1.7 Test Results Above 1GHz Data: 802.11n (HT20) + 802.11n (HT20) DETECTOR Peak (PK) CHANNEL CH 6 + CH 40 FUNCTION Average (AV) FREQUENCY RANGE 1GHz ~ 40GHz ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *2437.00 113.9 PK 3.32 H 292 80.3 33.6 2 *2437.00 103.0 AV 3.32 H 292 69.4 33.6 3 4874.00 60.0 PK 74.0 -14.0 3.19 H 189 56.1 3.9 4 4874.00 45.2 AV 54.0 -8.8 3.19 H 189 41.3 3.9 5 5150.00 58.7 PK 74.0 -15.3 2.71 H 283 54.8 3.9 6 5150.00 45.2 AV 54.0 -8.8 2.71 H 283 41.3 3.9 7 *5200.00 115.5 PK 2.67 H 278 74.7 40.8 8 *5200.00 104.2 AV 2.67 H 278 63.4 40.8 9 #10400.00 58.3 PK 74.0 -15.7 1.86 H 137 42.8 15.5 10 #10400.00 45.1 AV 54.0 -8.9 1.86 H 137 29.6 15.5 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *2437.00 123.7 PK 3.21 V 18 90.1 33.6 2 *2437.00 112.4 AV 3.21 V 18 78.8 33.6 3 4874.00 57.3 PK 74.0 -16.7 1.13 V 281 53.4 3.9 4 4874.00 49.8 AV 54.0 -4.2 1.13 V 281 45.9 3.9 5 5150.00 67.4 PK 74.0 -6.6 2.38 V 327 63.5 3.9 6 5150.00 51.1 AV 54.0 -2.9 2.38 V 327 47.2 3.9 7 *5200.00 124.4 PK 2.62 V 314 83.6 40.8 8 *5200.00 113.5 AV 2.62 V 314 72.7 40.8 9 #10400.00 60.1 PK 74.0 -13.9 1.74 V 285 44.6 15.5 10 #10400.00 46.3 AV 54.0 -7.7 1.74 V 285 30.8 15.5 Remarks: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value 5. " * ": Fundamental frequency. 6. " # ": The radiated frequency is out of the restricted band. Report No.: RF170801C12-2 Page No. 19 / 32 Report Format Version: 6.1.1

Below 1GHz data 802.11n (HT20) + 802.11n (HT20) CHANNEL CH 6 + CH 40 DETECTOR Quasi-Peak (QP) FREQUENCY RANGE 9kHz ~ 1GHz FUNCTION TEST MODE A ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 59.10 28.2 QP 40.0 -11.8 1.00 H 50 42.2 -14.0 2 224.00 30.1 QP 46.0 -15.9 1.49 H 111 46.1 -16.0 3 311.30 40.1 QP 46.0 -5.9 1.00 H 277 52.2 -12.1 4 377.26 37.4 QP 46.0 -8.6 1.00 H 172 48.7 -11.3 5 687.66 31.4 QP 46.0 -14.6 1.00 H 156 37.6 -6.2 6 924.34 28.9 QP 46.0 -17.1 1.99 H 223 31.3 -2.4 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 33.88 31.0 QP 40.0 -9.0 1.00 V 12 46.0 -15.0 2 224.00 30.1 QP 46.0 -15.9 1.49 V 111 46.1 -16.0 3 369.50 42.8 QP 46.0 -3.2 1.00 V 167 54.2 -11.4 4 538.28 39.7 QP 46.0 -6.3 1.49 V 166 48.7 -9.0 5 672.14 30.8 QP 46.0 -15.2 1.00 V 190 37.2 -6.4 6 939.86 37.2 QP 46.0 -8.8 1.00 V 225 39.4 -2.2 Remarks: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value Report No.: RF170801C12-2 Page No. 20 / 32 Report Format Version: 6.1.1

CHANNEL CH 6 + CH 40 DETECTOR Quasi-Peak (QP) FREQUENCY RANGE 9kHz ~ 1GHz FUNCTION TEST MODE B ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 59.10 30.4 QP 40.0 -9.6 2.00 H 108 44.4 -14.0 2 222.06 34.3 QP 46.0 -11.7 1.00 H 298 50.3 -16.0 3 352.04 41.6 QP 46.0 -4.4 1.00 H 163 53.3 -11.7 4 532.46 37.8 QP 46.0 -8.2 1.51 H 173 46.9 -9.1 5 672.14 31.5 QP 46.0 -14.5 1.00 H 16 37.9 -6.4 6 974.78 30.3 QP 54.0 -23.7 2.00 H 201 31.8 -1.5 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 33.88 28.7 QP 40.0 -11.3 1.51 V 221 43.7 -15.0 2 222.06 34.3 QP 46.0 -11.7 1.00 V 298 50.3 -16.0 3 365.62 41.9 QP 46.0 -4.1 1.00 V 147 53.4 -11.5 4 573.20 41.3 QP 46.0 -4.7 1.51 V 184 49.6 -8.3 5 672.14 31.5 QP 46.0 -14.5 1.00 V 16 37.9 -6.4 6 747.80 38.2 QP 46.0 -7.8 2.00 V 194 43.3 -5.1 Remarks: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value Report No.: RF170801C12-2 Page No. 21 / 32 Report Format Version: 6.1.1

CHANNEL CH 6 + CH 40 DETECTOR Quasi-Peak (QP) FREQUENCY RANGE 9kHz ~ 1GHz FUNCTION TEST MODE C ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 144.46 31.7 QP 43.5 -11.8 2.00 H 109 45.4 -13.7 2 241.46 30.6 QP 46.0 -15.4 1.00 H 124 45.1 -14.5 3 371.44 40.6 QP 46.0 -5.4 1.00 H 211 52.0 -11.4 4 501.42 34.5 QP 46.0 -11.5 1.51 H 188 43.9 -9.4 5 672.14 31.5 QP 46.0 -14.5 1.00 H 16 37.9 -6.4 6 747.80 38.2 QP 46.0 -7.8 2.00 H 194 43.3 -5.1 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 68.80 31.8 QP 40.0 -8.2 1.00 V 89 47.0 -15.2 2 222.06 33.3 QP 46.0 -12.7 1.49 V 132 49.3 -16.0 3 365.62 43.5 QP 46.0 -2.5 1.00 V 79 55.0 -11.5 4 582.90 37.6 QP 46.0 -8.4 1.49 V 15 45.6 -8.0 5 747.80 39.0 QP 46.0 -7.0 1.00 V 63 44.1 -5.1 6 937.92 30.4 QP 46.0 -15.6 2.00 V 236 32.6 -2.2 Remarks: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value Report No.: RF170801C12-2 Page No. 22 / 32 Report Format Version: 6.1.1

4.2 Conducted Emission Measurement 4.2.1 Limits of Conducted Emission Measurement Conducted Limit (dBuV) Frequency (MHz) Quasi-peak Average 0.15 - 0.5 66 - 56 56 - 46 0.50 - 5.0 56 46 5.0 - 30.0 60 50 Note: 1. The lower limit shall apply at the transition frequencies. 2. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50MHz. 4.2.2 Test Instruments Description & Manufacturer Model No. Serial No. Cal. Date Cal. Due Test Receiver ESCS 30 100288 Aug.17, 2017 Aug. 16, 2018 ROHDE & SCHWARZ RF signal cable (with 10dB PAD) 5D-FB Cable-cond2-01 Sep. 09, 2017 Sep. 08, 2018 Woken LISN ROHDE & SCHWARZ ESH2-Z5 100100 Jan. 17, 2017 Jan. 16, 2018 (EUT) LISN ROHDE & SCHWARZ ESH3-Z5 100312 Aug. 02, 2017 Aug. 01, 2018 (Peripheral) Software BV ADT_Cond_ NA NA NA ADT V7.3.7.3 Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Shielded Room 2. 3. The VCCI Site Registration No. is C-2047. Report No.: RF170801C12-2 Page No. 23 / 32 Report Format Version: 6.1.1

4.2.3 Test Procedures a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 ohm/ 50uH of coupling impedance for the measuring instrument. b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. c. The frequency range from 150kHz to 30MHz was searched. Emission levels under (Limit - 20dB) were not recorded. NOTE: The resolution bandwidth and video bandwidth of test receiver is 9kHz for quasi-peak detection (QP) and average detection (AV) at frequency 0.15MHz-30MHz. 4.2.4 Deviation from Test Standard No deviation. 4.2.5 Test Setup Vertical Ground Reference Plane Test Receiver EUT 40cm 80cm LISN Horizontal Ground Reference Plane Note: 1.Support units were connected to second LISN. For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.2.6 EUT Operating Conditions Same as 4.1.6. Report No.: RF170801C12-2 Page No. 24 / 32 Report Format Version: 6.1.1

4.2.7 Test Results 802.11n (HT20) + 802.11n (HT20) Quasi-Peak (QP) / Phase Line (L) Detector Function Average (AV) Channel CH 6 + CH 40 Test Mode A Corr. Reading Value Emission Level Limit Margin Freq. No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.16172 10.40 38.80 23.19 49.20 33.59 65.38 55.38 -16.18 -21.79 2 0.18516 10.41 33.79 19.09 44.20 29.50 64.25 54.25 -20.05 -24.75 3 0.23594 10.42 25.65 10.67 36.07 21.09 62.24 52.24 -26.17 -31.15 4 0.37656 10.41 28.39 20.02 38.80 30.43 58.35 48.35 -19.55 -17.92 5 5.28125 10.62 12.67 6.87 23.29 17.49 60.00 50.00 -36.71 -32.51 6 7.03906 10.65 18.22 12.58 28.87 23.23 60.00 50.00 -31.13 -26.77 Remarks: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level – Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value Report No.: RF170801C12-2 Page No. 25 / 32 Report Format Version: 6.1.1

Quasi-Peak (QP) / Phase Neutral (N) Detector Function Average (AV) Channel CH 6 + CH 40 Test Mode A Corr. Reading Value Emission Level Limit Margin Freq. No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.15781 10.42 38.57 21.62 48.99 32.04 65.58 55.58 -16.59 -23.54 2 0.37656 10.37 30.23 22.61 40.60 32.98 58.35 48.35 -17.75 -15.37 3 0.50547 10.40 17.17 9.20 27.57 19.60 56.00 46.00 -28.43 -26.40 4 1.52344 10.49 11.76 6.14 22.25 16.63 56.00 46.00 -33.75 -29.37 5 7.24219 10.63 16.55 11.51 27.18 22.14 60.00 50.00 -32.82 -27.86 6 10.30469 10.66 7.74 1.86 18.40 12.52 60.00 50.00 -41.60 -37.48 Remarks: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level – Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value Report No.: RF170801C12-2 Page No. 26 / 32 Report Format Version: 6.1.1

Quasi-Peak (QP) / Phase Line (L) Detector Function Average (AV) Channel CH 6 + CH 40 Test Mode B Corr. Reading Value Emission Level Limit Margin Freq. No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.16953 10.40 37.04 21.86 47.44 32.26 64.98 54.98 -17.54 -22.72 2 0.20078 10.42 31.36 16.39 41.78 26.81 63.58 53.58 -21.80 -26.77 3 0.38047 10.41 27.96 20.00 38.37 30.41 58.27 48.27 -19.90 -17.86 4 1.26563 10.50 12.16 6.42 22.66 16.92 56.00 46.00 -33.34 -29.08 5 7.46875 10.66 17.58 12.10 28.24 22.76 60.00 50.00 -31.76 -27.24 6 16.02734 10.81 6.61 0.86 17.42 11.67 60.00 50.00 -42.58 -38.33 Remarks: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level – Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value Report No.: RF170801C12-2 Page No. 27 / 32 Report Format Version: 6.1.1

Quasi-Peak (QP) / Phase Neutral (N) Detector Function Average (AV) Channel CH 6 + CH 40 Test Mode B Corr. Reading Value Emission Level Limit Margin Freq. No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.15781 10.42 38.34 21.05 48.76 31.47 65.58 55.58 -16.82 -24.11 2 0.18125 10.38 34.01 18.37 44.39 28.75 64.43 54.43 -20.04 -25.68 3 0.37266 10.37 30.21 21.86 40.58 32.23 58.44 48.44 -17.86 -16.21 4 4.46484 10.61 9.81 4.97 20.42 15.58 56.00 46.00 -35.58 -30.42 5 7.36719 10.63 16.21 11.50 26.84 22.13 60.00 50.00 -33.16 -27.87 6 15.59375 10.83 5.06 0.38 15.89 11.21 60.00 50.00 -44.11 -38.79 Remarks: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level – Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value Report No.: RF170801C12-2 Page No. 28 / 32 Report Format Version: 6.1.1

Quasi-Peak (QP) / Phase Line (L) Detector Function Average (AV) Channel CH 6 + CH 40 Test Mode C Corr. Reading Value Emission Level Limit Margin Freq. No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.15391 10.39 38.38 21.21 48.77 31.60 65.79 55.79 -17.02 -24.19 2 0.20078 10.42 31.28 16.23 41.70 26.65 63.58 53.58 -21.88 -26.93 3 0.37656 10.41 28.43 20.20 38.84 30.61 58.35 48.35 -19.51 -17.74 4 0.86875 10.47 10.31 3.13 20.78 13.60 56.00 46.00 -35.22 -32.40 5 4.89453 10.62 10.31 0.75 20.93 11.37 56.00 46.00 -35.07 -34.63 6 7.26172 10.66 18.23 13.06 28.89 23.72 60.00 50.00 -31.11 -26.28 Remarks: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level – Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value Report No.: RF170801C12-2 Page No. 29 / 32 Report Format Version: 6.1.1

Quasi-Peak (QP) / Phase Neutral (N) Detector Function Average (AV) Channel CH 6 + CH 40 Test Mode C Corr. Reading Value Emission Level Limit Margin Freq. No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.15000 10.43 40.31 23.29 50.74 33.72 66.00 56.00 -15.26 -22.28 2 0.16562 10.41 37.67 22.33 48.08 32.74 65.18 55.18 -17.10 -22.44 3 0.24766 10.36 25.54 12.74 35.90 23.10 61.84 51.84 -25.94 -28.74 4 0.38047 10.37 30.24 22.54 40.61 32.91 58.27 48.27 -17.66 -15.36 5 6.52734 10.62 16.11 12.83 26.73 23.45 60.00 50.00 -33.27 -26.55 6 28.75391 10.73 6.18 1.48 16.91 12.21 60.00 50.00 -43.09 -37.79 Remarks: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level – Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value Report No.: RF170801C12-2 Page No. 30 / 32 Report Format Version: 6.1.1

5 Pictures of Test Arrangements Please refer to the attached file (Test Setup Photo). Report No.: RF170801C12-2 Page No. 31 / 32 Report Format Version: 6.1.1

Appendix – Information on the Testing Laboratories We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are FCC recognized accredited test firms and accredited and approved according to ISO/IEC 17025. If you have any comments, please feel free to contact us at the following: Linko EMC/RF Lab Hsin Chu EMC/RF/Telecom Lab Tel: 886-2-26052180 Tel: 886-3-6668565 Fax: 886-2-26051924 Fax: 886-3-6668323 Hwa Ya EMC/RF/Safety Lab Tel: 886-3-3183232 Fax: 886-3-3270892 Email: service.adt@tw.bureauveritas.com Web Site: www.bureauveritas-adt.com The address and road map of all our labs can be found in our web site also. --- END --- Report No.: RF170801C12-2 Page No. 32 / 32 Report Format Version: 6.1.1


Document Created: 2018-03-13 14:28:02
Document Modified: 2018-03-13 14:28:02
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC