RF exposure evaluation

FCC ID: KA2AP1820A1

RF Exposure Info

Download: PDF
FCCID_4168747

FCC RF EXPOSURE EVALUATION REPORT FCC ID: KA2AP1820A1 Project No. : 1809H005 Equipment : AC2000 Wi-Fi Range Extender, AC2000 Mesh-Enabled Range Extender Model : DRA-2060, DAP-1820 Applicant : D-Link Corporation Address : 17595 Mt. Herrmann Fountain Valley California United States 92708 Exposure category : General population/uncontrolled environment EUT Type: : Production Unit (Engineer Sample) Device Type : Mobile Device

1. Evaluation Method Systems operating under the provisions of FCC 47 CFR section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. In accordance with 47 CFR FCC Part 2 Subpart J, section 2.1091 this device has been defined as mobile device whereby a distance of 0.2m normally can be maintained between the user and the device, and below RF Permissible Exposure limit shall comply with. In accordance with KDB447498D01 for Simultaneous transmission MPE test exclusion applies when the sum of the MPE ratios for all simultaneous transmitting antennas incorporated in a host device, based on the calculated/estimated, numerically modeled or measured field strengths or power density, is ≤ 1.0. The MPE ratio of each antenna is determined at the minimum test separation distance required by the operating configurations and exposure conditions of the host device, according to the ratio of field strengths or power density to MPE limit, at the test frequency. Either the maximum peak or spatially averaged results from measurements or numerical simulations may be used to determine the MPE ratios. Spatial averaging does not apply when MPE is estimated using simple calculations based on far- field plane-wave equivalent conditions. The antenna installation and operating requirements for the host device must meet the minimum test separation distances required by all antennas, in both standalone and simultaneous transmission operations, to satisfy compliance. 2. Limits for General Population/Uncontrolled Exposure 3. Refer Evaluation Method ANSI C95.1–1999: IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. FCC KDB publication 447498 D01 General RF Exposure Guidance v06: Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies. FCC CFR 47 part1 1.1310: Radiofrequency radiation exposure limits. FCC CFR 47 part2 2.1093: Radiofrequency radiation exposure evaluation: portable devices

4. Calculation Method Predication of MPE limit at a given distance Equation from page 18 of OET Bulletin 65, Edition 97-01 S=PG/4πR² Where: S=power density P=power input to antenna G=power gain of the antenna in the direction of interest relative to an isotropic radiator R=distance to the center of radiation of the antenna 5. Conducted Power Results 5.1 Test Setup 5.2 Test Equipment Item Kind of Equipment Manufacturer Type No. Serial No. Calibrated until 1 Power Meter Keysight 8990B MY51000507 Jul. 27, 2019 2 Pulse Power Sensor Keysight N1923A MY58310003 Aug. 07, 2019 Remark: all calibration period of equipment list is one year. 5.3 Test Procedure a. The EUT was directly connected to the power meter and antenna output port as show in the block diagram Test Setup. b. Setup EUT work at duty cycle more than 98%; c. Read power sensor values in RMS detector; 5.4 Test Results and Manufacturing Tolerance

Maximum average power declared by Manufacturer Mode Antenna 0 Antenna 1 IEEE 802.11b ≤ 17.00 ≤ 17.00 IEEE 802.11g ≤ 17.00 ≤ 17.00 IEEE 802.11n HT20 ≤ 17.00 ≤ 17.00 IEEE 802.11n HT40 ≤ 15.00 ≤ 15.00 5G UNII Band 1 Non-Beamforming Maximum Average power declared by Manufacturer Mode Antenna 0 Antenna 1 Antenna 2 Antenna 3 IEEE 802.11a ≤ 20.00 ≤ 20.00 ≤ 20.00 ≤ 20.00 IEEE 802.11n HT20 ≤ 15.50 ≤ 15.00 ≤ 14.00 ≤ 15.50 IEEE 802.11n HT40 ≤ 15.50 ≤ 14.50 ≤ 14.00 ≤ 15.00 IEEE 802.11ac VHT20 ≤ 15.50 ≤ 15.00 ≤ 14.00 ≤ 15.50 IEEE 802.11ac VHT40 ≤ 15.50 ≤ 15.00 ≤ 14.00 ≤ 15.50 IEEE 802.11ac VHT80 ≤ 11.00 ≤ 11.00 ≤ 10.00 ≤ 10.50 5G UNII Band 3 Non-Beamforming Maximum Average power declared by Manufacturer Mode Antenna 0 Antenna 1 Antenna 2 Antenna 3 IEEE 802.11a ≤ 21.00 ≤ 21.00 ≤ 21.00 ≤ 21.00 IEEE 802.11n HT20 ≤ 21.00 ≤ 21.50 ≤ 20.00 ≤ 21.50 IEEE 802.11n HT40 ≤ 19.50 ≤ 21.50 ≤ 20.50 ≤ 21.00 IEEE 802.11ac VHT20 ≤ 20.50 ≤ 21.50 ≤ 19.50 ≤ 20.50 IEEE 802.11ac VHT40 ≤ 21.00 ≤ 20.50 ≤ 19.50 ≤ 21.50 IEEE 802.11ac VHT80 ≤ 13.00 ≤ 13.50 ≤ 11.50 ≤ 13.50 5G UNII Band 1 Beamforming Maximum Average power declared by Manufacturer Mode Antenna 0 Antenna 1 Antenna 2 Antenna 3 IEEE 802.11n HT20 ≤ 15.50 ≤ 15.00 ≤ 14.00 ≤ 15.50 IEEE 802.11n HT40 ≤ 16.00 ≤ 15.00 ≤ 14.50 ≤ 16.00 IEEE 802.11ac VHT20 ≤ 16.00 ≤ 15.50 ≤ 15.00 ≤ 17.00 IEEE 802.11ac VHT40 ≤ 16.00 ≤15.50 ≤ 15.00 ≤ 16.50 IEEE 802.11ac VHT80 ≤ 11.00 ≤ 11.00 ≤ 10.00 ≤ 10.50 5G UNII-3 Beamforming Maximum Average power declared by Manufacturer Mode Antenna 0 Antenna 1 Antenna 2 Antenna 3 IEEE 802.11n HT20 ≤ 21.00 ≤ 21.50 ≤ 20.00 ≤ 21.50 IEEE 802.11n HT40 ≤ 19.50 ≤ 21.50 ≤ 20.50 ≤ 21.00 IEEE 802.11ac VHT20 ≤ 20.50 ≤ 21.50 ≤ 19.00 ≤ 20.50 IEEE 802.11ac VHT40 ≤ 22.00 ≤ 22.00 ≤ 20.50 ≤ 22.50 IEEE 802.11ac VHT80 ≤ 13.00 ≤ 13.50 ≤ 11.50 ≤ 13.50

6. Antenna Information Maximum Peak Gain Antenna Manufacturer P/N Antenna Type Connector (dBi) Antenna 0 RF link RF21C04071A PCB N/A 3 Antenna 1 RF link RF21C04071A PCB N/A 3 Antenna 2 RF link RF21C03745A PCB N/A 3 Antenna 3 RF link RF21C03745A PCB N/A 3 7. Evaluation Results 7.1 Standalone Evaluation [Antenna 0] Output power Antenna Antenna MPE Duty MPE Mode Gain Gain Limits (dBm) (mW) Cycle (mW/cm2) (dBi) (linear) (mW/cm2) IEEE 802.11b 17.00 50.1187 3 1.9953 100% 0.0199 1.0000 IEEE 802.11g 17.00 50.1187 3 1.9953 100% 0.0199 1.0000 IEEE 802.11n HT20 17.00 50.1187 3 1.9953 100% 0.0199 1.0000 IEEE 802.11n HT40 15.00 31.6228 3 1.9953 100% 0.0126 1.0000 [Antenna 1] Output power Antenna Antenna MPE Duty MPE Mode Gain Gain Limits (dBm) (mW) Cycle (mW/cm2) (dBi) (linear) (mW/cm2) IEEE 802.11b 17.00 50.1187 3 1.9953 100% 0.0199 1.0000 IEEE 802.11g 17.00 50.1187 3 1.9953 100% 0.0199 1.0000 IEEE 802.11n HT20 17.00 50.1187 3 1.9953 100% 0.0199 1.0000 IEEE 802.11n HT40 15.00 31.6228 3 1.9953 100% 0.0126 1.0000 Non-Beamforming UNII Band 1 [Antenna 0] Antenna Antenna Output power Duty MPE MPE Limits Mode Gain Gain Cycle (mW/cm2) (mW/cm2) (dBm) (mW) (dBi) (linear) IEEE 802.11a 20.00 100.0000 3 1.9953 100% 0.0397 1.0000 IEEE 802.11n HT20 15.50 35.4813 3 1.9953 100% 0.0141 1.0000 IEEE 802.11n HT40 15.50 35.4813 3 1.9953 100% 0.0141 1.0000 IEEE 802.11ac VHT20 15.50 35.4813 3 1.9953 100% 0.0141 1.0000 IEEE 802.11ac VHT40 15.50 35.4813 3 1.9953 100% 0.0141 1.0000 IEEE 802.11ac VHT80 11.00 12.5893 3 1.9953 100% 0.0050 1.0000

[Antenna 1] Antenna Antenna Output power Duty MPE MPE Limits Mode Gain Gain Cycle (mW/cm2) (mW/cm2) (dBm) (mW) (dBi) (linear) IEEE 802.11a 20.00 100.0000 3 1.9953 100% 0.0397 1.0000 IEEE 802.11n HT20 15.00 31.6228 3 1.9953 100% 0.0126 1.0000 IEEE 802.11n HT40 14.50 28.1838 3 1.9953 100% 0.0112 1.0000 IEEE 802.11ac VHT20 15.00 31.6228 3 1.9953 100% 0.0126 1.0000 IEEE 802.11ac VHT40 15.00 31.6228 3 1.9953 100% 0.0126 1.0000 IEEE 802.11ac VHT80 11.00 12.5893 3 1.9953 100% 0.0050 1.0000 [Antenna 2] Antenna Antenna Output power Duty MPE MPE Limits Mode Gain Gain Cycle (mW/cm2) (mW/cm2) (dBm) (mW) (dBi) (linear) IEEE 802.11a 20.00 100.0000 3 1.9953 100% 0.0397 1.0000 IEEE 802.11n HT20 14.00 25.1189 3 1.9953 100% 0.0100 1.0000 IEEE 802.11n HT40 14.00 25.1189 3 1.9953 100% 0.0100 1.0000 IEEE 802.11ac VHT20 14.00 25.1189 3 1.9953 100% 0.0100 1.0000 IEEE 802.11ac VHT40 14.00 25.1189 3 1.9953 100% 0.0100 1.0000 IEEE 802.11ac VHT80 10.00 10.0000 3 1.9953 100% 0.0040 1.0000 [Antenna 3] Antenna Antenna Output power Duty MPE MPE Limits Mode Gain Gain Cycle (mW/cm2) (mW/cm2) (dBm) (mW) (dBi) (linear) IEEE 802.11a 20.00 100.0000 3 1.9953 100% 0.0397 1.0000 IEEE 802.11n HT20 15.50 35.4813 3 1.9953 100% 0.0141 1.0000 IEEE 802.11n HT40 15.00 31.6228 3 1.9953 100% 0.0126 1.0000 IEEE 802.11ac VHT20 15.50 35.4813 3 1.9953 100% 0.0141 1.0000 IEEE 802.11ac VHT40 15.50 35.4813 3 1.9953 100% 0.0141 1.0000 IEEE 802.11ac VHT80 10.50 11.2202 3 1.9953 100% 0.0045 1.0000 Non-Beamforming UNII Band 3 [Antenna 0] Antenna Antenna Output power Duty MPE MPE Limits Mode Gain Gain Cycle (mW/cm2) (mW/cm2) (dBm) (mW) (dBi) (linear) IEEE 802.11a 21.00 125.8925 3 1.9953 100% 0.0500 1.0000 IEEE 802.11n HT20 21.00 125.8925 3 1.9953 100% 0.0500 1.0000 IEEE 802.11n HT40 19.50 89.1251 3 1.9953 100% 0.0354 1.0000 IEEE 802.11ac VHT20 20.50 112.2018 3 1.9953 100% 0.0446 1.0000 IEEE 802.11ac VHT40 21.00 125.8925 3 1.9953 100% 0.0500 1.0000 IEEE 802.11ac VHT80 13.00 19.9526 3 1.9953 100% 0.0079 1.0000

[Antenna 1] Antenna Antenna Output power Duty MPE MPE Limits Mode Gain Gain Cycle (mW/cm2) (mW/cm2) (dBm) (mW) (dBi) (linear) IEEE 802.11a 21.00 125.8925 3 1.9953 100% 0.0500 1.0000 IEEE 802.11n HT20 21.50 141.2538 3 1.9953 100% 0.0561 1.0000 IEEE 802.11n HT40 21.50 141.2538 3 1.9953 100% 0.0561 1.0000 IEEE 802.11ac VHT20 21.50 141.2538 3 1.9953 100% 0.0561 1.0000 IEEE 802.11ac VHT40 20.50 112.2018 3 1.9953 100% 0.0446 1.0000 IEEE 802.11ac VHT80 13.50 22.3872 3 1.9953 100% 0.0089 1.0000 [Antenna 2] Antenna Antenna Output power Duty MPE MPE Limits Mode Gain Gain Cycle (mW/cm2) (mW/cm2) (dBm) (mW) (dBi) (linear) IEEE 802.11a 21.00 125.8925 3 1.9953 100% 0.0500 1.0000 IEEE 802.11n HT20 20.00 100.0000 3 1.9953 100% 0.0397 1.0000 IEEE 802.11n HT40 20.50 112.2018 3 1.9953 100% 0.0446 1.0000 IEEE 802.11ac VHT20 19.50 89.1251 3 1.9953 100% 0.0354 1.0000 IEEE 802.11ac VHT40 19.50 89.1251 3 1.9953 100% 0.0354 1.0000 IEEE 802.11ac VHT80 11.50 14.1254 3 1.9953 100% 0.0056 1.0000 [Antenna 3] Antenna Antenna Output power Duty MPE MPE Limits Mode Gain Gain Cycle (mW/cm2) (mW/cm2) (dBm) (mW) (dBi) (linear) IEEE 802.11a 21.00 125.8925 3 1.9953 100% 0.0500 1.0000 IEEE 802.11n HT20 21.50 141.2538 3 1.9953 100% 0.0561 1.0000 IEEE 802.11n HT40 21.00 125.8925 3 1.9953 100% 0.0500 1.0000 IEEE 802.11ac VHT20 20.50 112.2018 3 1.9953 100% 0.0446 1.0000 IEEE 802.11ac VHT40 21.50 141.2538 3 1.9953 100% 0.0561 1.0000 IEEE 802.11ac VHT80 13.50 22.3872 3 1.9953 100% 0.0089 1.0000 5G Beamforming UNII Band 1 [Antenna 0] Antenna Antenna Output power Duty MPE MPE Limits Mode Gain Gain Cycle (mW/cm2) (mW/cm2) (dBm) (mW) (dBi) (linear) IEEE 802.11n HT20 15.50 35.4813 3 1.9953 100% 0.0141 1.0000 IEEE 802.11n HT40 16.00 39.8107 3 1.9953 100% 0.0158 1.0000 IEEE 802.11ac VHT20 16.00 39.8107 3 1.9953 100% 0.0158 1.0000 IEEE 802.11ac VHT40 16.00 39.8107 3 1.9953 100% 0.0158 1.0000 IEEE 802.11ac VHT80 11.00 12.5893 3 1.9953 100% 0.0050 1.0000

[Antenna 1] Antenna Antenna Output power Duty MPE MPE Limits Mode Gain Gain Cycle (mW/cm2) (mW/cm2) (dBm) (mW) (dBi) (linear) IEEE 802.11n HT20 15.00 31.6228 3 1.9953 100% 0.0126 1.0000 IEEE 802.11n HT40 15.00 31.6228 3 1.9953 100% 0.0126 1.0000 IEEE 802.11ac VHT20 15.50 35.4813 3 1.9953 100% 0.0141 1.0000 IEEE 802.11ac VHT40 15.50 35.4813 3 1.9953 100% 0.0141 1.0000 IEEE 802.11ac VHT80 11.00 12.5893 3 1.9953 100% 0.0050 1.0000 [Antenna 2] Antenna Antenna Output power Duty MPE MPE Limits Mode Gain Gain Cycle (mW/cm2) (mW/cm2) (dBm) (mW) (dBi) (linear) IEEE 802.11n HT20 14.00 25.1189 3 1.9953 100% 0.0100 1.0000 IEEE 802.11n HT40 14.50 28.1838 3 1.9953 100% 0.0122 1.0000 IEEE 802.11ac VHT20 15.00 31.6228 3 1.9953 100% 0.0126 1.0000 IEEE 802.11ac VHT40 15.00 31.6228 3 1.9953 100% 0.0126 1.0000 IEEE 802.11ac VHT80 10.00 10.0000 3 1.9953 100% 0.0040 1.0000 [Antenna 3] Antenna Antenna Output power Duty MPE MPE Limits Mode Gain Gain Cycle (mW/cm2) (mW/cm2) (dBm) (mW) (dBi) (linear) IEEE 802.11n HT20 15.50 35.4813 3 1.9953 100% 0.0141 1.0000 IEEE 802.11n HT40 16.00 39.8107 3 1.9953 100% 0.0158 1.0000 IEEE 802.11ac VHT20 17.00 50.1187 3 1.9953 100% 0.0199 1.0000 IEEE 802.11ac VHT40 16.50 44.6684 3 1.9953 100% 0.0177 1.0000 IEEE 802.11ac VHT80 10.50 11.2202 3 1.9953 100% 0.0045 1.0000 5G Beamforming UNII Band 3 [Antenna 0] Antenna Antenna Output power Duty MPE MPE Limits Mode Gain Gain Cycle (mW/cm2) (mW/cm2) (dBm) (mW) (dBi) (linear) IEEE 802.11n HT20 21.00 125.8925 3 1.9953 100% 0.0500 1.0000 IEEE 802.11n HT40 19.50 89.1251 3 1.9953 100% 0.0354 1.0000 IEEE 802.11ac VHT20 20.50 112.2018 3 1.9953 100% 0.0446 1.0000 IEEE 802.11ac VHT40 22.00 158.4893 3 1.9953 100% 0.0629 1.0000 IEEE 802.11ac VHT80 13.00 19.9526 3 1.9953 100% 0.0079 1.0000

[Antenna 1] Antenna Antenna Output power Duty MPE MPE Limits Mode Gain Gain Cycle (mW/cm2) (mW/cm2) (dBm) (mW) (dBi) (linear) IEEE 802.11n HT20 21.50 141.2538 3 1.9953 100% 0.0561 1.0000 IEEE 802.11n HT40 21.50 141.2538 3 1.9953 100% 0.0561 1.0000 IEEE 802.11ac VHT20 21.50 141.2538 3 1.9953 100% 0.0561 1.0000 IEEE 802.11ac VHT40 22.00 158.4893 3 1.9953 100% 0.0629 1.0000 IEEE 802.11ac VHT80 13.50 22.3872 3 1.9953 100% 0.0089 1.0000 [Antenna 2] Antenna Antenna Output power Duty MPE MPE Limits Mode Gain Gain Cycle (mW/cm2) (mW/cm2) (dBm) (mW) (dBi) (linear) IEEE 802.11n HT20 20.00 100.0000 3 1.9953 100% 0.0397 1.0000 IEEE 802.11n HT40 20.50 112.2018 3 1.9953 100% 0.0446 1.0000 IEEE 802.11ac VHT20 19.00 79.4328 3 1.9953 100% 0.0315 1.0000 IEEE 802.11ac VHT40 20.50 112.2018 3 1.9953 100% 0.0446 1.0000 IEEE 802.11ac VHT80 11.50 14.1254 3 1.9953 100% 0.0056 1.0000 [Antenna 3] Antenna Antenna Output power Duty MPE MPE Limits Mode Gain Gain Cycle (mW/cm2) (mW/cm2) (dBm) (mW) (dBi) (linear) IEEE 802.11n HT20 21.50 141.2538 3 1.9953 100% 0.0561 1.0000 IEEE 802.11n HT40 21.00 125.8925 3 1.9953 100% 0.0500 1.0000 IEEE 802.11ac VHT20 20.50 112.2018 3 1.9953 100% 0.0446 1.0000 IEEE 802.11ac VHT40 22.50 177.8279 3 1.9953 100% 0.0706 1.0000 IEEE 802.11ac VHT80 13.50 22.3872 3 1.9953 100% 0.0089 1.0000 Remark: 1. Maximum power including tune-up tolerance; 2. MPE use distance is 20cm from manufacturer declaration of user manual. 7.2 Simultaneous Transmission for MPE The sample support one WLAN modular and 2T2R MIMO antennas for 2.4GHz, the other WLAN modular support 4T4R MIMO antennas for 5GWLAN, 2.4GHz WLAN and 5GWLAN share two antennas, need consider simultaneous transmission;

Antenna 0 and Antenna 1 for 2.4GWLAN MPE Ratio MPE Ratio Band Mode ∑ MPE ratios Limit Results Antenna 0 Antenna 1 IEEE 802.11b 0.0199 0.0199 N/A 1.0 PASS IEEE 802.11g 0.0199 0.0199 < 0.1 1.0 PASS 2.4GHz IEEE 802.11n HT20 0.0199 0.0199 < 0.1 1.0 PASS IEEE 802.11n HT40 0.0126 0.0126 < 0.1 1.0 PASS Antenna 0, Antenna 1, Antenna 2 and Antenna 3 for 5GWLAN UNII Band 1 - Non-Beamforming MPE MPE MPE MPE ∑ MPE Band Mode Ratio Ratio Ratio Ratio Limit Results ratios Antenna 0 Antenna 1 Antenna 2 Antenna 3 IEEE 802.11a 0.0397 0.0397 0.0397 0.0397 N/A 1.0 PASS IEEE 802.11n HT20 0.0141 0.0126 0.0100 0.0141 < 0.1 1.0 PASS IEEE 802.11n HT40 0.0141 0.0112 0.0100 0.0126 < 0.1 1.0 PASS 5G IEEE 802.11ac VHT20 0.0141 0.0126 0.0100 0.0141 < 0.1 1.0 PASS IEEE 802.11ac VHT40 0.0141 0.0126 0.0100 0.0141 < 0.1 1.0 PASS IEEE 802.11ac VHT80 0.0050 0.0050 0.0040 0.0045 < 0.1 1.0 PASS Antenna 0, Antenna 1, Antenna 2 and Antenna 3 for 5GWLAN UNII Band 3 - Non-Beamforming MPE MPE MPE MPE ∑ MPE Band Mode Ratio Ratio Ratio Ratio Limit Results ratios Antenna 0 Antenna 1 Antenna 2 Antenna 3 IEEE 802.11a 0.0500 0.0500 0.0500 0.0500 N/A 1.0 PASS IEEE 802.11n HT20 0.0500 0.0561 0.0397 0.0561 < 0.3 1.0 PASS IEEE 802.11n HT40 0.0354 0.0561 0.0446 0.0500 < 0.3 1.0 PASS 5G IEEE 802.11ac VHT20 0.0446 0.0561 0.0354 0.0446 < 0.3 1.0 PASS IEEE 802.11ac VHT40 0.0500 0.0446 0.0354 0.0561 < 0.3 1.0 PASS IEEE 802.11ac VHT80 0.0079 0.0089 0.0056 0.0089 < 0.1 1.0 PASS Antenna 0, Antenna 1, Antenna 2 and Antenna 3 for 5GWLAN UNII Band 1 -Beamforming MPE MPE MPE MPE ∑ MPE Band Mode Ratio Ratio Ratio Ratio Limit Results ratios Antenna 0 Antenna 1 Antenna 2 Antenna 3 IEEE 802.11n HT20 0.0141 0.0126 0.0100 0.0141 < 0.1 1.0 PASS IEEE 802.11n HT40 0.0158 0.0126 0.0122 0.0158 < 0.1 1.0 PASS 5G IEEE 802.11ac VHT20 0.0158 0.0141 0.0126 0.0199 < 0.1 1.0 PASS IEEE 802.11ac VHT40 0.0158 0.0141 0.0126 0.0177 < 0.1 1.0 PASS IEEE 802.11ac VHT80 0.0050 0.0050 0.0040 0.0045 < 0.1 1.0 PASS

Antenna 0, Antenna 1, Antenna 2 and Antenna 3 for 5GWLAN UNII Band 3 - Beamforming MPE MPE MPE MPE ∑ MPE Band Mode Ratio Ratio Ratio Ratio Limit Results ratios Antenna 0 Antenna 1 Antenna 2 Antenna 3 IEEE 802.11n HT20 0.0500 0.0561 0.0397 0.0561 < 0.3 1.0 PASS IEEE 802.11n HT40 0.0354 0.0561 0.0446 0.0500 < 0.3 1.0 PASS 5G IEEE 802.11ac VHT20 0.0446 0.0561 0.0315 0.0446 < 0.3 1.0 PASS IEEE 802.11ac VHT40 0.0629 0.0629 0.0446 0.0706 < 0.3 1.0 PASS IEEE 802.11ac VHT80 0.0079 0.0089 0.0056 0.0089 < 0.3 1.0 PASS Maximum MPE Ratios for WLAN simultaneous transmission Maximum MPE Maximum MPE ∑ MPE ratios Limit Results Ratio 2.4GWLAN Ratio 5GWLAN < 0.1 < 0.3 < 0.4 1.0 PASS Remark: 1. Maximum power including tune-up tolerance; 2. MPE use distance is 20cm from manufacturer declaration of user manual. 8. Conclusion The measurement results comply with the FCC Limit per 47 CFR 2.1093 for the uncontrolled RF Exposure and SAR Exclusion Threshold per KDB 447498 v06. ---------------- END OF REPORT---------------


Document Created: 2019-02-12 22:25:26
Document Modified: 2019-02-12 22:25:26
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC