Test Report

FCC ID: K7SF7U027

Test Report

Download: PDF
FCCID_3540992

FCC Test Report Report No.: RF170814C07 FCC ID: K7SF7U027 Test Model: F7U027 Received Date: Aug. 14, 2017 Test Date: Aug. 20 ~ Aug. 23, 2017 Issued Date: Aug. 23, 2017 Applicant: Belkin International., Inc Address: 12045 East Waterfront Drive, Playa Vista, CA 90094 Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. Test Location: No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, TAIWAN (R.O.C.) This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF170814C07 Page No. 1 / 24 Report Format Version: 6.1.1

Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity...................................................................................................................... 4 2 Summary of Test Results ..................................................................................................................... 5 2.1 Measurement Uncertainty ................................................................................................................... 5 2.2 Modification Record ............................................................................................................................ 5 3 General Information .............................................................................................................................. 6 3.1 General Description of EUT ................................................................................................................ 6 3.2 Description of Test Modes ................................................................................................................... 6 3.2.1 Test Mode Applicability and Tested Channel Detail ............................................................................. 7 3.3 Description of Support Units ............................................................................................................... 8 3.3.1 Configuration of System under Test .................................................................................................... 8 3.4 General Description of Applied Standards .......................................................................................... 8 4 Test Types and Results ........................................................................................................................ 9 4.1 Radiated Emission and Bandedge Measurement............................................................................... 9 4.1.1 Limits of Radiated Emission and Bandedge Measurement ................................................................ 9 4.1.2 Test Instruments ................................................................................................................................ 10 4.1.3 Test Procedures.................................................................................................................................. 11 4.1.4 Deviation from Test Standard ............................................................................................................. 11 4.1.5 Test Set Up ........................................................................................................................................ 12 4.1.6 EUT Operating Conditions................................................................................................................. 12 4.1.7 Test Results ....................................................................................................................................... 13 4.2 Conducted Emission Measurement .................................................................................................. 17 4.2.1 Limits of Conducted Emission Measurement .................................................................................... 17 4.2.2 Test Instruments ................................................................................................................................ 17 4.2.3 Test Procedures................................................................................................................................. 18 4.2.4 Deviation from Test Standard ............................................................................................................ 18 4.2.5 Test Setup .......................................................................................................................................... 18 4.2.6 EUT Operating Conditions................................................................................................................. 18 4.2.7 Test Results ....................................................................................................................................... 19 5 Pictures of Test Arrangements .......................................................................................................... 23 Appendix – Information on the Testing Laboratories ................................................................................ 24 Report No.: RF170814C07 Page No. 2 / 24 Report Format Version: 6.1.1

Release Control Record Issue No. Description Date Issued RF170814C07 Original release Aug. 23, 2017 Report No.: RF170814C07 Page No. 3 / 24 Report Format Version: 6.1.1

1 Certificate of Conformity Product: Boostup Wireless Charging Pad Brand: belkin Model No.: F7U027 Sample Status: Engineering sample Applicant: Belkin International., Inc Test Date: Aug. 20 ~ Aug. 23, 2017 Standards: 47 CFR FCC Part 15, Subpart C (Section 15.209) ANSI C63.10: 2013 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. Prepared by : , Date: Aug. 23, 2017 Celine Chou / Specialist Approved by : , Date: Aug. 23, 2017 Ken Liu / Senior Manager Report No.: RF170814C07 Page No. 4 / 24 Report Format Version: 6.1.1

2 Summary of Test Results 47 CFR FCC Part 15, Subpart C (Section 15.209) FCC Test Item Result Remarks Clause Meet the requirement of limit. 15.207 AC Power Conducted Emission Pass Minimum passing margin is -11.47dB at 0.39654MHz. Meet the requirement of limit. 15.209 Radiated Emission Test Pass Minimum passing margin is -6.6dB at 49.34MHz. 2.1 Measurement Uncertainty Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2: Expanded Uncertainty Measurement Frequency (k=2) (±) Conducted Emissions at mains ports 150kHz ~ 30MHz 2.94 dB 30MHz ~ 200MHz 3.86 dB Radiated Emissions up to 1 GHz 200MHz ~ 1000MHz 3.87 dB 2.2 Modification Record There were no modifications required for compliance. Report No.: RF170814C07 Page No. 5 / 24 Report Format Version: 6.1.1

3 General Information 3.1 General Description of EUT Product Boostup Wireless Charging Pad Test Model F7U027 Sample Status Engineering sample Power Supply Rating 15Vdc (adapter) Modulation Type FSK Operating Frequency 127.8 kHz Antenna Type Coil antenna Accessory Device Adapter Data Cable Supplied NA Note: 1. The EUT uses following adapter. Brand belkin Model ADS-26FSG-12 15023EPCU Input Power 100-240Vac, 50/60Hz, Max 0.7A Output Power 15Vdc, 1.5A Power Line 1.45m non-shielded DC cable without core attached on adapter 2. The EUT has WPC (Wireless Power Consortium) technology. 3.2 Description of Test Modes 1 channel is provided to this EUT Channel Freq. (kHz) 1 127.8 Report No.: RF170814C07 Page No. 6 / 24 Report Format Version: 6.1.1

3.2.1 Test Mode Applicability and Tested Channel Detail EUT APPLICABLE TO DESCRIPTION CONFIGURE MODE RE<1G PLC A √ √ Charging Mode B √ √ Standby Mode Where RE<1G: Radiated Emission below 1GHz PLC: Power Line Conducted Emission Radiated Emission Test (Below 1GHz): Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Configure Mode Available Channel Tested Channel A, B 1 1 Power Line Conducted Emission Test: Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Configure Mode Available Channel Tested Channel A, B 1 1 Test Condition: Applicable To Environmental Conditions Input Power Tested by Willy Cheng RE<1G 22 deg. C, 68% RH 120Vac, 60Hz Jones Chang PLC 25 deg. C, 75% RH 120Vac, 60Hz Willy Cheng Report No.: RF170814C07 Page No. 7 / 24 Report Format Version: 6.1.1

3.3 Description of Support Units The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. ID Product Brand Model No. Serial No. FCC ID Remarks 7.5W Receiver Qi Receiver A. AVID NA NA Provided by manufacturer Load Simulator 3.3.1 Configuration of System under Test Test Mode A 7.5W Receiver Load (A) Adapter (EUT) USB EUT Test Mode B Adapter (EUT) USB EUT 3.4 General Description of Applied Standards The EUT is a RF Product. According to the specifications of the manufacturer, it must comply with the requirements of the following standards: FCC Part 15, Subpart C (15.209) ANSI C63.10-2013 All test items have been performed and recorded as per the above standards. Report No.: RF170814C07 Page No. 8 / 24 Report Format Version: 6.1.1

4 Test Types and Results 4.1 Radiated Emission and Bandedge Measurement 4.1.1 Limits of Radiated Emission and Bandedge Measurement FOR FREQUENCY BELOW 30MHz Frequency Field Strength (dBuV/m) Measurement Distance (MHz) uV/m dBuV/m (meters) 0.009 – 0.490 2400 / F (kHz) 48.52-13.80 300 0.490 – 1.705 24000 / F (kHz) 33.80-22.97 30 1.705 – 30.0 30 29.54 30 FOR FREQUENCY BETWEEN 30-1000MHz Frequency Class A (at 10m) Class B (at 3m) (MHz) uV/m dBuV/m uV/m dBuV/m 30-88 90 39.1 100 40.0 88-216 150 43.5 150 43.5 216-960 210 46.4 200 46.0 Above 960 300 49.5 500 54.0 Report No.: RF170814C07 Page No. 9 / 24 Report Format Version: 6.1.1

4.1.2 Test Instruments Description & Model No. Serial No. Cal. Date Cal. Due Manufacturer Test Receiver ESIB7 100187 May 02, 2017 May 01, 2018 ROHDE & SCHWARZ Spectrum Analyzer FSP40 100041 Nov. 16, 2016 Nov. 15, 2017 ROHDE & SCHWARZ BILOG Antenna VULB9168 9168-171 Dec. 28, 2016 Dec. 27, 2017 SCHWARZBECK HORN Antenna 9120D 209 Dec. 27, 2016 Dec. 26, 2017 SCHWARZBECK HORN Antenna BBHA 9170 BBHA9170241 Dec. 14, 2016 Dec. 13, 2017 SCHWARZBECK Loop Antenna EM-6879 269 Aug. 11, 2017 Aug. 10, 2018 Preamplifier 8447D 2944A10738 Aug. 21, 2017 Aug. 20, 2018 Agilent Preamplifier 8449B 3008A01922 Sep. 18, 2016 Sep. 17, 2017 Agilent RF signal cable SUCOFLEX 104 Cable-CH3-03 (223653/4) Aug. 21, 2017 Aug. 20, 2018 HUBER+SUHNER RF signal cable Cable-CH3-03 SUCOFLEX 106 Aug. 21, 2017 Aug. 20, 2018 HUBER+SUHNER (309224+12738) Software ADT_Radiated_ NA NA NA BV ADT V7.6.15.9.4 Antenna Tower MA 4000 013303 NA NA inn-co GmbH Antenna Tower Controller AT100 AT93021702 NA NA BV ADT Turn Table TT100 TT93021702 NA NA BV ADT Turn Table Controller SC100 SC93021702 NA NA BV ADT Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Chamber 3. 3. The horn antenna and preamplifier (model: 8449B) are used only for the measurement of emission frequency above 1GHz if tested. 4. The IC Site Registration No. is IC 7450F-3. Report No.: RF170814C07 Page No. 10 / 24 Report Format Version: 6.1.1

4.1.3 Test Procedures For Frequency range 9kHz~30MHz a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter Semi-anechoic chamber room. The table was rotated 360 degrees to determine the position of the highest radiation. Then the Loop antenna was rotated 360 degrees to determine the position of the highest radiation. b. The antenna is a broadband loop antenna, which is fixed of a 1m height above the ground, and set away from 3m to the EUT to find the disturbance reading on each frequency. c. The test-receiver system was set to Quasi-peak detect function and specified bandwidth. For Frequency range 30 ~ 1000MHz a. The EUT was placed on the top of a rotating table 0.8 meters (for below 1GHz) / 1.5 meters (for above 1GHz) above the ground at 3 meter chamber room for test. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The height of antenna is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to quasi-peak detect function and specified bandwidth with maximum hold mode when the test frequency is below 1 GHz. f. The test-receiver system was set to peak and average detect function and specified bandwidth with maximum hold mode when the test frequency is above 1 GHz. If the peak reading value also meets average limit, measurement with the average detector is unnecessary. Note: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for Quasi-peak detection (QP) at frequency below 1GHz. 2. All modes of operation were investigated and the worst-case emissions are reported. 4.1.4 Deviation from Test Standard No deviation. Report No.: RF170814C07 Page No. 11 / 24 Report Format Version: 6.1.1

4.1.5 Test Set Up For Frequency range 9kHz~30MHz EUT& 3m Loop antenna Support Units Turn Table 80cm Ground Plane Test Receiver For Frequency range 30 ~ 1000MHz Ant. Tower 1-4m Variable EUT& 3m 10m Support Units Turn Table 80cm Ground Plane Test Receiver For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.1.6 EUT Operating Conditions Test Mode A a. The EUT powered by adapter. b. Put the load on the EUT (wireless charging) during the test. Test Mode B a. The EUT powered by adapter. Report No.: RF170814C07 Page No. 12 / 24 Report Format Version: 6.1.1

4.1.7 Test Results Below 30MHz Data: Charging Mode Channel TX Channel 1 Detector Function Quasi-Peak Frequency Range 9 kHz ~ 30 MHz Test Mode A ANTENNA POLARITY & TEST DISTANCE: LOOP ANTENNA OPEN AT 3m Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *0.128 71.0 105.5 -34.5 1.00 196 50.7 20.3 2 0.369 52.3 96.3 -44.0 1.00 133 32.0 20.3 3 1.269 44.9 65.5 -20.6 1.00 318 24.6 20.3 4 3.728 38.2 69.5 -31.3 1.00 38 17.8 20.4 5 11.226 36.5 69.5 -33.0 1.00 224 16.0 20.5 6 18.244 37.4 69.5 -32.1 1.00 284 16.9 20.5 7 22.622 36.3 69.5 -33.2 1.00 296 15.8 20.5 ANTENNA POLARITY & TEST DISTANCE: LOOP ANTENNA CLOSE AT 3m Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *0.128 65.9 105.5 -39.6 1.00 295 45.6 20.3 2 0.369 47.7 96.3 -48.6 1.00 269 27.4 20.3 3 1.329 45.7 65.1 -19.4 1.00 344 25.4 20.3 4 3.968 36.2 69.5 -33.3 1.00 49 15.8 20.4 5 9.486 37.3 69.5 -32.2 1.00 219 16.9 20.4 6 16.324 36.3 69.5 -33.2 1.00 232 15.7 20.6 7 27.361 38.6 69.5 -30.9 1.00 81 18.0 20.6 Remarks: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value 5. “ * “: Fundamental frequency. 6. Loop antenna was used for all radiated emission below 30MHz. 7. Limit @3m=Limit@300m+40log(300 / 3)=Limit@300m+80 8. Limit @3m=Limit@30m+40log(30 / 3)=Limit@30m+40 Report No.: RF170814C07 Page No. 13 / 24 Report Format Version: 6.1.1

Standby Mode Channel TX Channel 1 Detector Function Quasi-Peak Frequency Range 9 kHz ~ 30 MHz Test Mode B ANTENNA POLARITY & TEST DISTANCE: LOOP ANTENNA OPEN AT 3m Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 0.384 47.1 95.9 -48.8 1.00 7 26.8 20.3 2 3.128 43.9 69.5 -25.6 1.00 149 23.5 20.4 3 14.345 38.9 69.5 -30.6 1.00 66 18.4 20.5 4 16.444 37.7 69.5 -31.8 1.00 334 17.1 20.6 5 17.464 38.3 69.5 -31.2 1.00 36 17.8 20.5 6 22.922 39.7 69.5 -29.8 1.00 176 19.2 20.5 ANTENNA POLARITY & TEST DISTANCE: LOOP ANTENNA CLOSE AT 3m Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 0.383 37.1 95.9 -58.8 1.00 300 16.8 20.3 2 3.128 41.9 69.5 -27.6 1.00 137 21.5 20.4 3 3.548 40.9 69.5 -28.6 1.00 87 20.5 20.4 4 5.107 39.9 69.5 -29.6 1.00 355 19.4 20.5 5 15.784 41.4 69.5 -28.1 1.00 141 20.8 20.6 6 22.742 40.1 69.5 -29.4 1.00 351 19.6 20.5 Remarks: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value 5. “ * “: Fundamental frequency. 6. Loop antenna was used for all radiated emission below 30MHz. 7. Limit @3m=Limit@300m+40log(300 / 3)=Limit@300m+80 8. Limit @3m=Limit@30m+40log(30 / 3)=Limit@30m+40 Report No.: RF170814C07 Page No. 14 / 24 Report Format Version: 6.1.1

Below 1GHz Data: Charging Mode Channel TX Channel 1 Detector Function Quasi-Peak Frequency Range 30 MHz ~ 1GHz Test Mode A Antenna Polarity & Test Distance: Horizontal At 3m Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 49.34 27.4 QP 40.0 -12.6 1.50 H 286 41.7 -14.3 2 84.34 22.6 QP 40.0 -17.4 1.50 H 319 42.0 -19.4 3 121.28 22.5 QP 43.5 -21.0 1.50 H 106 38.6 -16.1 4 197.11 27.4 QP 43.5 -16.1 1.50 H 283 44.0 -16.6 5 234.05 22.5 QP 46.0 -23.5 1.50 H 104 38.3 -15.8 6 875.67 27.3 QP 46.0 -18.7 1.50 H 10 30.8 -3.5 Antenna Polarity & Test Distance: Vertical At 3m Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 30.54 29.6 QP 40.0 -10.4 1.50 V 339 46.0 -16.4 2 49.34 33.4 QP 40.0 -6.6 1.00 V 239 47.7 -14.3 3 84.34 27.6 QP 40.0 -12.4 1.00 V 356 47.0 -19.4 4 138.78 24.1 QP 43.5 -19.4 1.00 V 244 38.6 -14.5 5 440.15 22.1 QP 46.0 -23.9 1.00 V 291 32.4 -10.3 6 935.94 28.7 QP 46.0 -17.3 1.00 V 118 31.3 -2.6 Remarks: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value Report No.: RF170814C07 Page No. 15 / 24 Report Format Version: 6.1.1

Standby Mode Channel TX Channel 1 Detector Function Quasi-Peak Frequency Range 30 MHz ~ 1GHz Test Mode B Antenna Polarity & Test Distance: Horizontal At 3m Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 30.00 25.7 QP 40.0 -14.3 1.00 H 302 42.1 -16.4 2 49.34 29.3 QP 40.0 -10.7 1.99 H 321 43.6 -14.3 3 74.62 31.2 QP 40.0 -8.8 1.99 H 269 48.4 -17.2 4 103.78 22.0 QP 43.5 -21.5 1.99 H 33 40.0 -18.0 5 140.72 21.5 QP 43.5 -22.0 1.99 H 241 35.8 -14.3 6 187.39 28.1 QP 43.5 -15.4 1.50 H 77 43.8 -15.7 Antenna Polarity & Test Distance: Vertical At 3m Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 30.55 29.9 QP 40.0 -10.1 1.00 V 216 46.3 -16.4 2 50.41 32.9 QP 40.0 -7.1 1.00 V 267 47.3 -14.4 3 84.34 29.0 QP 40.0 -11.0 1.50 V 13 48.4 -19.4 4 103.78 25.1 QP 43.5 -18.4 1.00 V 121 43.1 -18.0 5 131.00 24.8 QP 43.5 -18.7 1.00 V 144 40.2 -15.4 6 158.22 24.2 QP 43.5 -19.3 1.00 V 119 37.8 -13.6 7 840.67 37.1 QP 46.0 -8.9 1.00 V 146 38.0 -0.9 Remarks: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value Report No.: RF170814C07 Page No. 16 / 24 Report Format Version: 6.1.1

4.2 Conducted Emission Measurement 4.2.1 Limits of Conducted Emission Measurement Conducted Limit (dBuV) Frequency (MHz) Quasi-peak Average 0.15 - 0.5 66 - 56 56 - 46 0.50 - 5.0 56 46 5.0 - 30.0 60 50 Note: 1. The lower limit shall apply at the transition frequencies. 2. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50MHz. 4.2.2 Test Instruments Description & Manufacturer Model No. Serial No. Cal. Date Cal. Due Test Receiver ESCS 30 100288 Aug. 18, 2017 Aug. 17, 2018 ROHDE & SCHWARZ RF signal cable (with 10dB PAD) 5D-FB Cable-cond2-01 Dec. 22, 2016 Dec. 21, 2017 Woken LISN ROHDE & SCHWARZ ESH2-Z5 100100 Jan. 17, 2017 Jan. 16, 2018 (EUT) LISN ROHDE & SCHWARZ ESH3-Z5 100312 Aug. 02, 2017 Aug. 01, 2018 (Peripheral) Software BV ADT_Cond_ NA NA NA ADT V7.3.7.3 Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Shielded Room 2. 3. The VCCI Site Registration No. is C-2047. Report No.: RF170814C07 Page No. 17 / 24 Report Format Version: 6.1.1

4.2.3 Test Procedures a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 ohm/ 50uH of coupling impedance for the measuring instrument. b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. c. The frequency range from 150kHz to 30MHz was searched. Emission levels under (Limit - 20dB) were not recorded. NOTE: The resolution bandwidth and video bandwidth of test receiver is 9kHz for quasi-peak detection (QP) and average detection (AV) at frequency 0.15MHz-30MHz. 4.2.4 Deviation from Test Standard No deviation. 4.2.5 Test Setup Vertical Ground Reference Plane Test Receiver EUT 40cm 80cm LISN Horizontal Ground Reference Plane Note: 1.Support units were connected to second LISN. For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.2.6 EUT Operating Conditions Same as 4.1.6. Report No.: RF170814C07 Page No. 18 / 24 Report Format Version: 6.1.1

4.2.7 Test Results Charging Mode Quasi-Peak (QP) / Phase Line (L) Detector Function Average (AV) Test Mode A Corr. Reading Value Emission Level Limit Margin Freq. No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.18037 10.21 32.73 23.21 42.94 33.42 64.47 54.47 -21.53 -21.05 2 0.35407 10.28 26.44 25.46 36.72 35.74 58.87 48.87 -22.15 -13.13 3 0.39654 10.30 28.01 26.16 38.31 36.46 57.93 47.93 -19.62 -11.47 4 5.36600 10.47 21.38 14.81 31.85 25.28 60.00 50.00 -28.15 -24.72 5 5.88200 10.49 22.29 14.32 32.78 24.81 60.00 50.00 -27.22 -25.19 6 28.75000 11.51 26.07 26.02 37.58 37.53 60.00 50.00 -22.42 -12.47 Remarks: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level - Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value. Report No.: RF170814C07 Page No. 19 / 24 Report Format Version: 6.1.1

Quasi-Peak (QP) / Phase Neutral (N) Detector Function Average (AV) Test Mode A Corr. Reading Value Emission Level Limit Margin Freq. No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.17157 9.97 30.35 17.42 40.32 27.39 64.88 54.88 -24.56 -27.49 2 0.21576 9.98 24.56 12.44 34.54 22.42 62.98 52.98 -28.44 -30.56 3 0.35407 10.01 23.54 22.82 33.55 32.83 58.87 48.87 -25.32 -16.04 4 1.15564 10.05 22.16 16.20 32.21 26.25 56.00 46.00 -23.79 -19.75 5 3.44873 10.15 19.71 14.79 29.86 24.94 56.00 46.00 -26.14 -21.06 6 28.75000 11.02 27.02 26.82 38.04 37.84 60.00 50.00 -21.96 -12.16 Remarks: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level - Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value. Report No.: RF170814C07 Page No. 20 / 24 Report Format Version: 6.1.1

Standby Mode Quasi-Peak (QP) / Phase Line (L) Detector Function Average (AV) Test Mode B Corr. Reading Value Emission Level Limit Margin Freq. No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.16932 10.21 15.82 0.61 26.03 10.82 64.99 54.99 -38.96 -44.17 2 0.31949 10.26 13.34 2.41 23.60 12.67 59.72 49.72 -36.12 -37.05 3 0.38218 10.29 20.57 6.23 30.86 16.52 58.23 48.23 -27.37 -31.71 4 0.62715 10.28 7.54 -1.12 17.82 9.16 56.00 46.00 -38.18 -36.84 5 1.89640 10.29 3.98 -3.17 14.27 7.12 56.00 46.00 -41.73 -38.88 6 5.79000 10.48 9.17 -2.28 19.65 8.20 60.00 50.00 -40.35 -41.80 Remarks: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level - Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value. Report No.: RF170814C07 Page No. 21 / 24 Report Format Version: 6.1.1

Quasi-Peak (QP) / Phase Neutral (N) Detector Function Average (AV) Test Mode B Corr. Reading Value Emission Level Limit Margin Freq. No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.24485 9.99 6.69 -1.29 16.68 8.70 61.93 51.93 -45.25 -43.23 2 0.29992 10.00 9.79 0.56 19.79 10.56 60.25 50.25 -40.46 -39.69 3 0.40179 10.02 14.89 3.99 24.91 14.01 57.82 47.82 -32.91 -33.81 4 0.54542 10.02 5.90 -2.62 15.92 7.40 56.00 46.00 -40.08 -38.60 5 0.84019 10.03 10.87 -1.94 20.90 8.09 56.00 46.00 -35.10 -37.91 6 1.94190 10.08 5.98 -2.36 16.06 7.72 56.00 46.00 -39.94 -38.28 Remarks: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level - Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value. Report No.: RF170814C07 Page No. 22 / 24 Report Format Version: 6.1.1

5 Pictures of Test Arrangements Please refer to the attached file (Test Setup Photo). Report No.: RF170814C07 Page No. 23 / 24 Report Format Version: 6.1.1

Appendix – Information on the Testing Laboratories We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are FCC recognized accredited test firms and accredited and approved according to ISO/IEC 17025. If you have any comments, please feel free to contact us at the following: Linko EMC/RF Lab Hsin Chu EMC/RF/Telecom Lab Tel: 886-2-26052180 Tel: 886-3-6668565 Fax: 886-2-26051924 Fax: 886-3-6668323 Hwa Ya EMC/RF/Safety Lab Tel: 886-3-3183232 Fax: 886-3-3270892 Email: service.adt@tw.bureauveritas.com Web Site: www.bureauveritas-adt.com The address and road map of all our labs can be found in our web site also. --- END --- Report No.: RF170814C07 Page No. 24 / 24 Report Format Version: 6.1.1


Document Created: 2017-08-29 16:44:03
Document Modified: 2017-08-29 16:44:03
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC