Test Report

FCC ID: K66VX-150

Test Report

Download: PDF
FCCID_1109883

849 NW State Road 45 Newberry, Fl 32669 USA Phone: 888.472.2424 or 352.472.5500 Fax: 352.472.2030 Email: info@timcoengr.com Website: www.timcoengr.com FCC PART 15 SCANNING RECEIVER Applicant VERTEX STANDARD CO., LTD. Address 4-8-8 NAKAMEGURO, MEGURO-KU TOKYO 153-8644 JAPAN FCC ID: K66VX-150 Model Number FT-250R Product Description SCANNING RECEIVER Date Sample Received 4/23/2009 Date Tested 4/30/2009 Tested By Joe Scoglio Approved By Mario de Aranzeta Report Number 855AUT9TestReport.doc Test Results PASS FAIL THE ATTACHED REPORT SHALL NOT BE REPRODUCED EXCEPT IN FULL WITHOUT THE WRITTEN APPROVAL OF TIMCO ENGINEERING, INC. Certificate # 0955-01

TABLE OF CONTENTS GENERAL REMARKS ...................................................................................................3 GENERAL INFORMATION ............................................................................................4 TEST EQUIPMENT LIST ...............................................................................................5 TEST PROCEDURE......................................................................................................6 RADIATED SPURIOUS EMISSIONS .............................................................................7 POWER LINE CONDUCTED INTERFERENCE ..............................................................8 APPLICANT: VERTEX STANDARD CO., LTD. FCC ID: K66VX-150 REPORT #: V\VERTEX_STANDARD\855AUT9\855AUT9TestReport.doc Page 2 of 8

GENERAL REMARKS The attached report shall not be reproduced except in full without the written permission of Timco Engineering Inc. Summary The device under test does: fulfill the general approval requirements as identified in this test report not fulfill the general approval requirements as identified in this test report This is a request for a Class II Permissive change. With the change, this device becomes model number FT-250R. Radiated emissions testing was completed and there is no degradation from previously reported data. Attestations This equipment has been tested in accordance with the standards identified in this test report. To the best of my knowledge and belief, these tests were performed using the measurement procedures described in this report. All instrumentation and accessories used to test products for compliance to the indicated standards are calibrated regularly in accordance with ISO 17025 requirements. Testing Certificate # 0955-01 I attest that the necessary measurements were made, under my supervision, at: Timco Engineering Inc. 849 NW State Road 45 Newberry, Fl 32669 Authorized Signatory Name: Mario de Aranzeta C.E.T. Compliance Engineer/ Lab. Supervisor Date: 4/30/2009 APPLICANT: VERTEX STANDARD CO., LTD. FCC ID: K66VX-150 REPORT #: V\VERTEX_STANDARD\855AUT9\855AUT9TestReport.doc Page 3 of 8

GENERAL INFORMATION The test results relate only to the items tested. DUT Description SCANNING RECEIVER FCC ID K66VX-150 Model Number FT-250R DUT Power Source 110–120Vac/50– 60Hz DC Power Battery Operated Exclusively Test Item Prototype Pre-Production Production Modifications to DUT None Test Standards FCC Part 15, Subpart B, ANSI C63.4-2003 APPLICANT: VERTEX STANDARD CO., LTD. FCC ID: K66VX-150 REPORT #: V\VERTEX_STANDARD\855AUT9\855AUT9TestReport.doc Page 4 of 8

TEST EQUIPMENT LIST Serial Cal/Char Device Manufacturer Model Due Date Number Date Listed 3/10-Meter OATS TEI N/A N/A 3/19/10 3/20/07 Listed 3-Meter OATS TEI N/A N/A 2/5/12 2/5/09 3-Meter Semi- Listed Anechoic Panashield N/A N/A 5/11/10 5/11/07 Chamber Analyzer Tan CAL Tower Quasi-Peak HP 85650A 3303A01690 11/30/09 11/30/07 Adapter Analyzer Tan CAL Tower RF HP 85685A 3221A01400 11/30/09 11/30/07 Preselector Analyzer Tan 8566B Opt 3138A07786 CAL Tower Spectrum HP 11/30/09 462 3144A20661 11/30/07 Analyzer Analyzer Tan CAL Tower HP 8449B-H02 3008A00372 11/30/09 11/30/07 Preamplifier Frequency HP 5385A 2730A03025 CAL 7/6/07 7/6/09 Counter Hygro- CAL Extech 445703 0602 11/15/09 Thermometer 11/15/07 Measuring Tape- 7.5M CHAR Kraftixx 11/13/09 7.5M PROFI 11/13/07 Modulation HP 8901A 3435A06868 CAL 5/9/07 5/9/09 Analyzer FLUKE-77- CAL Digital Multimeter Fluke 79510405 5/14/09 3 5/14/07 System CHAR System One Audio Precision SYS1-45868 2/27/10 One 2/27/08 Temperature Tenney CHAR TTRC 11717-7 4/25/10 Chamber Engineering 4/25/08 APPLICANT: VERTEX STANDARD CO., LTD. FCC ID: K66VX-150 REPORT #: V\VERTEX_STANDARD\855AUT9\855AUT9TestReport.doc Page 5 of 8

TEST PROCEDURE General: This report shall NOT be reproduced except in full without the written approval of TIMCO ENGINEERING, INC. Radiation Interference: The test procedure used was ANSI Standard C63.4-2003 using a spectrum analyzer with a pre-selector. The bandwidth of the spectrum analyzer was 100 kHz with an appropriate sweep speed. The analyzer was calibrated in dB above a microvolt at the output of the antenna. The video bandwidth was always greater than or equal to the RBW. Formula Of Conversion Factors: The Field Strength at 3m was established by adding the meter reading of the spectrum analyzer (which is set to read in units of dBuV) to the antenna correction factor supplied by the antenna manufacturer. The antenna correction factors are stated in terms of dB. The gain of the Preselector was accounted for in the Spectrum Analyzer Meter Reading. Example: Freq (MHz) Meter Reading + ACF +CL = FS 33 20 dBuV + 10.36 dB/m +0.40 dB =30.36 dBuV/m @ 3m ANSI C63.4-2003 Section 10.1.7 Measurement Procedures: The unit under test was placed on a table 80 cm high and with dimensions of 1mby 1.5m. The table used for radiated measurements is capable of continuous rotation. When an emission was found, the table was rotated to produce the maximum signal strength. At this point, the antenna was raised and lowered from 1m to 4m. The antenna was placed in both the horizontal and verticals planes. If powerline conducted testing was required for this device, the situation was similar for the conducted measurement except that the table did not rotate. The EUT was setup as described in ANSI C63.4-2003 with the EUT 40 cm from the vertical ground wall. APPLICANT: VERTEX STANDARD CO., LTD. FCC ID: K66VX-150 REPORT #: V\VERTEX_STANDARD\855AUT9\855AUT9TestReport.doc Page 6 of 8

RADIATED SPURIOUS EMISSIONS Rules Part No.: 15.109 Requirements: Frequency Limits 30 – 88 40.0 dBµV/m measured @ 3 meters 80 – 216 43.5 dBµV/m measured @ 3 meters 216 – 960 46.0 dBµV/m measured @ 3 meters Above 960 54.0 dBµV/m measured @ 3 meters Test Procedure: The procedure used was ANSI C63.4-2003. The frequency was scanned from 30 MHz to 1.0 GHz. When an emission was found, the table was rotated to produce the maximum signal strength. The DUT was measured in three (3) orthogonal planes. Test Data: Tuned Emission Meter Ant. Coax Correction Field Margin Frequency Frequency Reading Pol Loss Factor Strength dB MHz MHz dBµV dB dB/m dBµV/m 140.5 118.80 1.9 H 0.67 13.54 16.11 27.39 140.5 118.80 2.1 V 0.67 13.66 16.43 27.07 155.0 133.30 1.8 H 0.68 12.90 15.38 28.12 155.0 133.30 2.0 V 0.68 12.73 15.41 28.09 173.5 151.80 1.7 H 0.71 13.79 16.20 27.30 173.5 151.80 2.0 V 0.71 14.37 17.08 26.42 APPLICANT: VERTEX STANDARD CO., LTD. FCC ID: K66VX-150 REPORT #: V\VERTEX_STANDARD\855AUT9\855AUT9TestReport.doc Page 7 of 8

POWER LINE CONDUCTED INTERFERENCE Rules Part No.: Part 15.107 Requirements: Frequency Quasi Peak Limits Average Limits (MHz) (dBµV) (dBµV) 0.15 – 0.5 66 – 56 56 – 46 0.5 – 5.0 56 46 5.0 – 30 60 50 Test Procedure: ANSI Standard C63.4-2003. The spectrum was scanned from 0.15 to 30 MHz . Test Data: The attached graphs represent the emissions read for power line conducted. Both lines were observed. NOTE DUT BATTERY POWERED HANDHELD APPLICANT: VERTEX STANDARD CO., LTD. FCC ID: K66VX-150 REPORT #: V\VERTEX_STANDARD\855AUT9\855AUT9TestReport.doc Page 8 of 8


Document Created: 2009-05-12 20:11:47
Document Modified: 2009-05-12 20:11:47
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC