test report

FCC ID: K66FT-897

Test Report

Download: PDF
FCCID_242538

FCC ID: K66FT-897 C E R T I F I C A T I O N of RECEIVER MODEL: FT-897 FCC ID: K66FT-897 to FEDERAL COMMUNICATIONS COMMISSION Part 15(B) (New) DATE OF REPORT: May 1, 2002 ON THE BEHALF OF THE APPLICANT: Vertex Standard Co., Ltd. AT THE REQUEST OF: P.O. UPS 4/24/2002 Vertex Standard USA Inc. 10900 Walker Street Cypress, CA 90630 Attention of: Mikio Maruya, Executive Vice President (800) 255-9237; FAX: (800) 477-9237 (714) 827-7600; FAX: -8100 m.maruya@vxstdusa.com SUPERVISED BY: Morton Flom, P. Eng. MFA p0240006, d0250001

FCC ID: K66FT-897 TABLE OF CONTENTS RULE DESCRIPTION PAGE 2.948 Description of Measurement Facilities 1 15.109 Receiver Spurious Emissions (Radiated) 6 15.121(b) Scanning Receiver 11 15.107 A/C Powerline Conducted Emissions 13 MFA p0240006, d0250001

FCC ID: K66FT-897 PAGE NO. 1 of 19. Required information per ISO/IEC Guide 25-1990, paragraph 13.2: a) TEST REPORT b) Laboratory: M. Flom Associates, Inc. (FCC: 31040/SIT) 3356 N. San Marcos Place, Suite 107 (Canada: IC 2044) Chandler, AZ 85225 c) Report Number: d0250001 d) Client: Vertex Standard USA Inc. 10900 Walker Street Cypress, CA 90630 e) Identification: FT-897 FCC ID: K66FT-897 Description: Scanning Receiver f) EUT Condition: Not required unless specified in individual tests. g) Report Date: May 1, 2002 EUT Received: April 24, 2002 h, j, k): As indicated in individual tests. i) Sampling method: No sampling procedure used. l) Uncertainty: In accordance with MFA internal quality manual. m) Supervised by: Morton Flom, P. Eng. n) Results: The results presented in this report relate only to the item tested. o) Reproduction: This report must not be reproduced, except in full, without written permission from this laboratory. MFA p0240006, d0250001

FCC ID: K66FT-897 PAGE NO. 2 of 19. M. Flom Associates, Inc. is accredited by the American Association for Laboratory Association (A2LA) as shown in the scope below. "This laboratory is accredited by the American Association for Laboratory Accreditation (A2LA) and the results shown in this report have been determined in accordance with the laboratory's terms of accreditation unless stated otherwise in the report." Should this report contain any data for tests for which we are not accredited, or which have been undertaken by a subcontractor that is not A2LA accredited, such data would not covered by this laboratory's A2LA accreditation. MFA p0240006, d0250001

FCC ID: K66FT-897 PAGE NO. 3 of 19. GENERAL INFORMATION Part 2.948: (a)(b) DESCRIPTION OF MEASUREMENT FACILITIES: FILE: 31040/SIT A description of the measurement facilities was filed with the Commission and was found to be in compliance with the requirements of Section 2.948, by letter dated March 13, 2000. All pertinent changes will be reported to the Commission by up-date prior to March 2003. (b)(4) SUPPORTING STRUCTURES: SKETCH - ATTACHED EXHIBITS (b)(5)(6) TEST INSTRUMENTATION: LIST - SEE EXHIBITS 2.925: IDENTIFICATION OF AN AUTHORIZED DEVICE: DRAWING - SEE EXHIBITS LOCATION OF LABEL - SEE PHOTOS NAME AND ADDRESS OF APPLICANT: Vertex Standard Co., Ltd. 4-8-8 Nakameguro, Meguro-Ku Tokyo 153-8644 Japan MFA p0240006, d0250001

FCC ID: K66FT-897 PAGE NO. 4 of 19. 2.911: 2.1033(b)(6) TECHNICAL REPORT MANUFACTURER: Vertex Standard Co., Ltd. 4-8-8 Nakameguro, Meguro-Ku Tokyo 153-8644 Japan FCC ID: K66FT-897 MODEL NO: FT-897 PHOTOGRAPHS: SEE LIST OF EXHIBITS DUT DESCRIPTION: This unit Passes 15.31: MEASUREMENT STANDARD & PROCEDURE: IEEE STANDARD 187 WAS USED AS A GUIDE. FCC MEASUREMENT PROCEDURE MP-1 x ANSI 63.4 (1992/2000) “Methods of measurement of radio-noise emissions from low-voltage electrical and electronic equipment in the range of 9 kHz to 40 GHz.” MFA p0240006, d0250001

FCC ID: K66FT-897 PAGE NO. 5 of 19. EXPOSITORY STATEMENT 1. NUMBER OF BANDS = 4 2. NUMBER OF CHANNELS = per manual 3. TUNING RANGE, MHz = 0.1 to 56.0 76 to 108 118 to 164 420 to 470 4. OSCILLATOR RANGE, MHz = 68.4 to 124.32 65.3 to 118.7 186.33 to 232.33 488.33 to 513.33 5. I.F., MHz = 68.33 6. BLOCK DIAGRAM = ATTACHED 7. For cellular receiver only, the radio transceiver meets the requirements of FCC Bulletin OET 53 ("Cellular System Mobile Stations-Land-System Compatibility Specification."). See attached affidavit. 15.203: ANTENNA REQUIREMENT: The antenna is permanently attached to the EUT The antenna uses a unique coupling The EUT must be professionally installed x The antenna requirement does not apply SUPERVISED BY: Morton Flom, P. Eng. MFA p0240006, d0250001

FCC ID: K66FT-897 PAGE NO. 6 of 19. NAME OF TEST: Receiver Spurious Emissions (Radiated) SPECIFICATION: 15.109: Radiated Interference Limits 15.33: Frequency Range of Radiated Measurements 80.217: Suppression of Interference Aboard Ships GUIDE: See measurement procedure below TEST CONDITIONS: Standard Temperature & Humidity TEST EQUIPMENT: As per attached page SEARCH ANTENNAS: 100 Hz - 50 MHz: Emco 3301B Active Rod 10 kHz - 32 MHz: Singer 94593-1 Loop 25 MHz - 300 MHz: Emco 3109 Biconical 200 MHz - 1 GHz: Aprel 2001 Log Periodic 1 GHz - 18 GHz: Emco 3115 Horn 10 GHz - 40 GHz: Emco 3116 Horn with HP11970A Mixer MEASUREMENT PROCEDURE 1. At first, bench tests were performed to locate the spurious emissions at the antenna terminals. 2. In the field, tests were conducted over the range shown, The test sample was set up on a wooden turntable above ground, and at a distance of three meters from the antenna connected tot he Spectrum Analyzer. 3. In order to obtain the maximum response at each frequency, the turntable was rotated, and the search antenna was raised and lowered. The EUT was also adjusted for maximum response. Tests were conducted in Horizontal & Vertical polarization modes. 4. The field strength was calculated from: E µV/m @ 3 m = Log10-1(dBµV + A.F. + C.L.) 20 5. MEASUREMENT RESULTS: Attached for "Worst Case" conditions. MFA p0240006, d0250001

FCC ID: K66FT-897 PAGE NO. 7 of 19. RADIATED TEST SETUP NOTES: (a)Search Antenna - Rotatable on (j)Cables routed through hollow boom turntable center (b)Non-metallic boom (k)30 cm or less (c)Non-metallic mast (l)External power source (d)Adjustable horizontally (m)10 cm diameter coil of excess (e)Equipment Under Test cable (f)Turntable (n)25 cm (V), 1 m-7 m (V, H) (g)Boom adjustable in height. (o)25 cm from bottom end of 'V', (h)External control cables routed 1m normally horizontally at least one (p)Calibrated Cable at least 10m wavelength. in length (i)Rotatable (q)Amplifier (optional) (r)Spectrum Analyzer Asset Description s/n Cycle Last Cal (as applicable) Per ANSI C63.4-1992/2000 Draft, 10.1.4 TRANSDUCER i00088 EMCO 3109-B 25MHz-300MHz 2336 12 mo. Sep-01 i00089 Aprel 2001 200MHz-1GHz 001500 12 mo. Sep-01 i00103 EMCO 3115 1GHz-18GHz 9208-3925 12 mo. Sep-01 i00065 EMCO 3301-B Active Monopole 2635 12 mo. Sep-01 AMPLIFIER i00028 HP 8449A 2749A00121 12 mo. Mar-02 SPECTRUM ANALYZER i00029 HP 8563E 3213A00104 12 mo. Jan-02 i00033 HP 85462A 3625A00357 12 mo. Jan-02 i00048 HP 8566B 2511AD1467 6 mo. Jan-02 MISCELLANEOUS Microphone Antenna All Ports Terminated MFA p0240006, d0250001

FCC ID: K66FT-897 PAGE NO. 8 of 19. TEST SETUP: Radiated Emissions MFA p0240006, d0250001

FCC ID: K66FT-897 PAGE NO. 9 of 19. NAME OF TEST: Receiver Spurious Emissions (Radiated) MEASUREMENT DETAILS SITE REFERENCE = 31040/SIT SPECTRUM SEARCHED = 0 to 10 x FR WORST CASE = V LIMITS = 15.109(a) (Attached) ALL OTHER EMISSIONS = 20 dB OR MORE BELOW LIMIT TESTS WERE CONDUCTED WITH: a. All controls and switches operated. b. Half-wave dipole antenna or manufacturer/applicant supplied antenna. SAMPLE CALCULATION: EMISSION FREQUENCY, MHz = 0.100000 LEVEL = Log10-1 (_21.37_+ 55.2 ) 20 LEVEL, µV/m @ 0m = 6737.52 MEASUREMENT RESULTS = ATTACHED NOTE: WORST CASE OF SCAN AND NON-SCAN MODES REPORTED. MFA p0240006, d0250001

FCC ID: K66FT-897 PAGE NO. 10 of 19. NAME OF TEST: Receiver Spurious Emissions (Radiated) RULE 15.109(a) LIMITS: FREQUENCY, FIELD STRENGTH DISTANCE, MHz µV/m m 30 - 88 100 3 88 - 216 150 3 216 - 960 200 3 Above 960 500 3 g0240067: 2002-Apr-25 Thu 16:13:00 FREQUENCY FREQUENCY LEVEL, @ m C.F., dB µV/m @ m TUNED, MHz EMISSION, MHz dBuV 0.100000 68.430900 16.3 3 12.71 28.22 3 28.050000 96.380000 17.32 3 13.54 34.91 3 56.000000 124.330000 10.59 3 16.5 22.62 3 28.050000 192.760000 12.73 3 18.93 38.28 3 56.000000 248.612500 12.11 3 21.35 47.1 3 g0240065: 2002-Apr-25 Thu 14:46:00 FREQUENCY FREQUENCY LEVEL, @ m C.F., dB µV/m @ m TUNED, MHz EMISSION, MHz dBuV 76.000000 65.298000 14.09 3 13.35 23.55 3 92.000000 102.698000 16.87 3 14.48 36.94 3 108.000000 118.698000 7.92 3 16.02 15.74 3 76.000000 130.690000 11.2 3 16.71 24.86 3 92.000000 205.433000 8.54 3 19.55 25.38 3 108.000000 237.458000 12.22 3 20.91 45.34 3 g0240066: 2002-Apr-25 Thu 15:28:00 FREQUENCY FREQUENCY LEVEL, @ m C.F., dB µV/m @ m TUNED, MHz EMISSION, MHz dBuV 118.000000 186.329500 9.85 3 18.58 26.39 3 141.000000 209.329500 11.22 3 19.73 35.28 3 164.000000 232.329500 10.99 3 20.7 38.41 3 118.000000 372.660000 12.86 3 24.94 77.62 3 141.000000 418.652500 12.03 3 26.33 82.79 3 164.000000 464.656000 13.57 3 26.38 99.43 3 g0240064: 2002-Apr-25 Thu 13:07:00 FREQUENCY FREQUENCY LEVEL, @ m C.F., dB µV/m @ m TUNED, MHz EMISSION, MHz dBuV 420.000000 488.330000 11.18 3 26.4 75.68 3 445.000000 513.343000 11.62 3 26.88 84.14 3 470.000000 538.343000 11.29 3 27.74 89.43 3 420.000000 976.210000 12.83 3 40.01 438.53 3 445.000000 1026.210000 12.36 3 36.16 266.69 3 445.000000 1076.648000 10.39 3 36.82 229.35 3 All other emissions in the required measurement range were more that 20 dB below the required limits. PERFORMED BY: Doug Noble, B.A.S. E.E.T. MFA p0240006, d0250001

FCC ID: K66FT-897 PAGE NO. 11 of 19. NAME OF TEST: Scanning Receivers Cellular Band Rejection SPECIFICATION: FCC: 47 CFR 15.121(b) TEST EQUIPMENT: As per attached page GUIDE: 47 CFR 15.121(b): Except as provided in paragraph (c) of this section, scanning receivers shall reject any signals from Cellular Radiotelephone Service frequency bands that are 38 dB or higher based upon a 12 dB SINAD measurement, which is considered the threshold where a signal can be clearly discerned from any interference that may be present. WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW. MEASUREMENT PROCEDURE 1. Equipment was connected as illustrated in the block diagram. 2. A standard signal was applied to the receiver input terminals. 3. Receiver output audio output was adjusted for rated output and with distortion no greater than 10%. 4. The RF Signal generator was adjusted to produce 12dB SINAD without the audio output power dropping by more than 3dB. 5. This was repeated at three frequencies across all bands to establish a reference sensitivity level. The reference sensitivity taken was the lowest, or worst-case sensitivity for all of the bands. 6. The output of the signal generator was then adjusted to a level of +60dB above the reference level sensitivity established in step 5 and set to the first of three frequencies in the cellular subscriber transmit band. 7. Receiver squelch threshold, the signal level required to open the squelch, should be set to open no greater than +20dB above the reference sensitivity. 8. The receiver was then put in the scanning mode and allowed to scan across it’s complete receive range. 9. If the receiver unsquelched or stopped on any frequency, the displayed frequency was recorded. The signal generator was then adjusted in output level until a 12dB SINAD from the receiver was produced. The signal generator level associated with this response was also noted. 10. This procedure was repeated for three frequencies in the cellular base station transmit band. 11. The difference in between the signal generator output for any response recorded and the reference sensitivity is the rejection ratio. MFA p0240006, d0250001

FCC ID: K66FT-897 PAGE NO. 12 of 19. SCANNING RECEIVER: Distortion Meter RF Signal Scanning SINAD Generator Receiver Meter Audio Power Meter Reference Level Sensitivity measured in step 5 = Frequency of Displayed Level for 12 dB Rejection, dB EUT, MHz Frequency, MHz SINAD, dBm 848.97 0.100 – 056 836.4 < -113 < -130 824.04 848.97 76 – 108 836.4 < -113 < -130 824.04 848.97 118 – 164 836.4 < -113 < -130 824.04 848.97 420 - 470 836.4 < -113 < -130 824.04 NOTE: 1) System Sensitivity = -130 dbm 2) No spurious response detectable within these frequency ranges. PERFORMED BY: Doug Noble, B.A.S. E.E.T. MFA p0240006, d0250001

FCC ID: K66FT-897 PAGE NO. 13 of 19. NAME OF TEST: A/C Powerline Conducted Emissions SPECIFICATION: FCC: 47 CFR 15.107 GUIDE: IEEE Standard 213 TEST CONDITIONS: S. T. & H. TEST EQUIPMENT: As per attached page MEASUREMENT PROCEDURE 1. A test sample was connected to the Public Utility lines through a LISN Ailtech Model 94641-1 (50 µH). 2. A reference level of 250 µV was set on the Spectrum Analyzer. The spectrum was searched over the range of 450 kHz to 30 MHz. 3. All other emissions were 20 dB or more below limit. 4. x The test sample used a charger. The test sample does not use a charger. 5. Measurement Results: Attached. MFA p0240006, d0250001

FCC ID: K66FT-897 PAGE NO. 14 of 19. AC POWERLINE CONDUCTED MEASUREMENTS Public (2) Test Utility (1) A/C Powerline Conducted Sample Line (3) Asset Description s/n Cycle Last Cal (as applicable) Per ANSI C63.4-1992/2000 Draft, 10.1.4 (1) LINE IMPEDANCE STABILIZATION NETWORK i00077 Singer 91221-1 (5 µH) 0396 12 mo. i00155 Eaton 94641-1 (50 µH) 178 12 mo. Sep-01 i00167 Ailtech 94641-1 (50 µH) 0103 12 mo. (2) SCREEN ROOM i00169 Lindgren 22-2/2-0 3861 N/A none i00170 Lindgren LG170 4999 (3) SPECTRUM ANALYZER i00029 HP 8563E 3213A00104 12 mo. Jan-02 i00033 HP 85462A 3625A00357 12 mo. Jan-02 i00048 HP 8566B 2511AD1467 6 mo. Jan-02 MFA p0240006, d0250001

FCC ID: K66FT-897 PAGE NO. 15 of 19. TEST SETUP: A/C Powerline Conducted Emissions MFA p0240006, d0250001

FCC ID: K66FT-897 PAGE NO. 16 of 19. NAME OF TEST: A/C Powerline Conducted Emissions g0240068: 2002-Apr-30 Tue 11:55:00 STATE: 0:General NEUTRAL SIDE, GROUNDED PERFORMED BY: Doug Noble, B.A.S. E.E.T. MFA p0240006, d0250001

FCC ID: K66FT-897 PAGE NO. 17 of 19. NAME OF TEST: A/C Powerline Conducted Emissions g0240069: 2002-Apr-30 Tue 11:57:00 STATE: 0:General LINE SIDE, GROUNDED PERFORMED BY: Doug Noble, B.A.S. E.E.T. MFA p0240006, d0250001

FCC ID: K66FT-897 PAGE NO. 18 of 19. NAME OF TEST: A/C Powerline Conducted Emissions g0240070: 2002-Apr-30 Tue 12:00:00 STATE: 0:General LINE SIDE, GROUNDED PERFORMED BY: Doug Noble, B.A.S. E.E.T. MFA p0240006, d0250001

FCC ID: K66FT-897 PAGE NO. 19 of 19. NAME OF TEST: A/C Powerline Conducted Emissions g0240071: 2002-Apr-30 Tue 12:02:00 STATE: 0:General NEUTRAL SIDE, GROUNDED PERFORMED BY: Doug Noble, B.A.S. E.E.T. END OF TEST REPORT MFA p0240006, d0250001

FCC ID: K66FT-897 THE APPLICANT HAS BEEN CAUTIONED AS TO THE FOLLOWING: 15.21 INFORMATION TO USER. The users manual or instruction manual for an intentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 15.27(a) SPECIAL ACCESSORIES. Equipment marketed to a consumer must be capable of complying with the necessary regulations in the configuration in which the equipment is marketed. Where special accessories, such as shielded cables and/or special connectors are required to enable an unintentional or intentional radiator to comply with the emission limits in this part, the equipment must be marketed with, i.e. shipped and sold with, those special accessories. However, in lieu of shipping or packaging the special accessories with the unintentional or intentional radiator, the responsible party may employ other methods of ensuring that the special accessories are provided to the consumer, without additional charge. Information detailing any alternative method used to supply the special accessories for a grant of equipment authorization or retained in the verification records, as appropriate. The party responsible for the equipment, as detailed in § 2.909 of this chapter, shall ensure that these special accessories are provided with the equipment. The instruction manual for such devices shall include appropriate instructions on the first page of text concerned with the installation of the device that these special accessories must be used with the device. It is the responsibility of the user to use the needed special accessories supplied with the equipment. MFA p0240006, d0250001

FCC ID: K66FT-897 LABELLING OF SCANNING RECEIVERS ' Scanning receivers shall have a label permanently affixed to the product, and this label shall be readily visible to the purchaser at the time of purchase. The label shall read as follows: WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW. "Permanently affixed" means that the label is etched, engrave, stamped, silkscreened, indelibly printed or otherwise permanently marked on a permanently attached part of the equipment or on a nameplate of metal plastic or other material fastened to the equipment by welding, riveting, or permanent adhesive. The label shall be designed to last the expected lifetime of the equipment in the environment in which the equipment may be operated and must not be readily detachable. The label shall not be a stick-on, paper label. MFA p0240006, d0250001

FCC ID: K66FT-897 STATEMENT OF COMPLIANCE THIS IS TO CERTIFY: THAT, ON THE BASIS OF THE MEASUREMENTS MADE, THE EQUIPMENT TESTED IS CAPABLE OF COMPLYING WITH THE REQUIREMENTS OF FCC RULE PART 15, SUBPART B x_ FCC RULE PART 15, SUBPART C ___ USING ANSI C63.4-1992/2000 Draft IN EFFECT AS OF THIS DATE, UNDER NORMAL OPERATION, WITH THE USUAL MAINTENANCE. THAT THE DATA CONTAINED HEREIN IS A SUMMARY (WORST CASE) OF THAT OBTAINED ON SEVERAL RANDOMLY-SELECTED PRODUCTION SAMPLES. THAT THE EQUIPMENT MEETS OR EXCEEDS THE REQUIREMENTS OF PART 15. MFA p0240006, d0250001

FCC ID: K66FT-897 LIST OF EXHIBITS (FCC CERTIFICATION (RECEIVERS) - REVISED 9/28/98) APPLICANT: Vertex Standard Co., Ltd. EQUIPMENT: FT-897 K66FT-897 BY APPLICANT: IF APPLICABLE: Subsection 2.1033 1. LETTER OF AUTHORIZATION 2. ATTESTATION 3. IDENTIFICATION LABEL DRAWING LABEL LOCATION OF LABEL COMPLIANCE STATEMENT LOCATION OF COMPLIANCE STATEMENT 4. DOCUMENTATION: 2.1033(b) (3) USER MANUAL (4) OPERATIONAL DESCRIPTION (5) BLOCK DIAGRAM (5) SCHEMATIC DIAGRAM (7) PHOTOGRAPHS BY M.F.A. INC. A. STATEMENT OF COMPLIANCE B. STATEMENT OF QUALIFICATIONS MFA p0240006, d0250001


Document Created: 2002-05-06 09:15:17
Document Modified: 2002-05-06 09:15:17
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC