Operating Manual 95_102

FCC ID: K6630633X30

Users Manual

Download: PDF
FCCID_3849299

POS FIX WAIT Sets the maximum wait time to obtain position infor- 15 sec mation when receiving a Distress Alert, POS Report call, or acknowledgement to POS request call DSC BEEP Turns the audible alarm ON or OFF when receiv- Indivi.: On ing a DSC call All Ship: On Group: On POS RQ.: Off POS RP.: On Geog.: On Polling: Off Test Call: Off 17. GPS SETUP The “GPS Setup” mode allows the parameters for the HX890 internal GPS unit to be customized for your operating requirements. 17.1 GPS ON/OFF This selection allows the internal GPS unit to be turned ON or OFF to conserve battery power. The default setting is “ON”. Press and hold SELECT GPS ON/OFF ON SELECT     key ( / key) ( key) ( / key) ( key) 1. Press the CH▼/CH▲ key to select “OFF”, GPS SETUP GPS ON/OFF OFF “ON”, or “INT and PWR OFF”. ON INT at PWR OFF OFF: GPS OFF ON: GPS ON BACK ENTER INT and PWR OFF: GPS ON, even when the transceiver is OFF. 2. Press the [ENTER] soft key to save the new setting. 3. Press the CLR key to return to radio operation. NOTE When “INT and PWR OFF” is set, the battery is depleted little by little because the internal GPS unit is activated. When the transceiver is OFF with “INT and PWR OFF” is set, charge the battery by connecting the Charger cradle. 17.2 POWER SAVE This menu item selects the Battery Save Mode for the internal GPS unit. The default setting for the Power Save Mode is “AUTO”. Press and hold SELECT POWER SAVE SELECT     key ( / key) ( key) ( / key) ( key) 95

1. Press the CH▼/CH▲ key to select the GPS SETUP POWER SAVE OFF desired level. AUTO 50% OFF: GPS signals are always being received. 75% 90% BACK ENTER AUTO: Activates the GPS receiver automatically when GPS signals are received. 50%: Activates the GPS receiver for 3 seconds every 3 seconds. 75%: Activates the GPS receiver for 3 seconds every 9 seconds. 90%: Activates the GPS receiver for 3 seconds every 27 seconds. 2. Press the [ENTER] soft key to store the selected setting. 3. Press the CLR key to return to radio operation. 17.3 DISPLAY DIRECTION This menu item selects the compass orientation to be shown on the HX890 display. The default setting is “course up”. Press and hold SELECT DIRECTION SELECT     key ( / key) ( key) ( / key) ( key) 1. Press the CH▼/CH▲ key to select the GPS SETUP DIRECTION desired direction from “COURSE UP” and COURSE UP NORTH UP “NORTH UP”. 2. Press the [ENTER] soft key to save the new BACK ENTER setting. 3. Press the CLR key to return to radio operation. 17.4 LOCATION FORMAT This menu item selects the coordinate system to be shown on the HX890 display. The default setting is “ddd mm.mmm”. Press and hold SELECT LOCATION FORMAT SELECT     key ( / key) ( key) ( / key) ( key) 1. Press the CH▼/CH▲ key to select the GPS SETUP LOCATION FORMAT desired coordinate system. The location ddd°mm.mmm format can be selected from “ddd°mm.mmm”, ddd°mm.mm ddd°mm’ss” “ddd°mm.mm”, and “ddd°mm’ss””. 2. Press the [ENTER] soft key to save the new BACK ENTER setting. 3. Press the CLR key to return to radio operation. 17.5 TIME OFFSET Sets the local time offset between UTC (Universal Time Coordinated) and local 96

time shown on the display. The offset is added or subtracted from the time received from the GPS. Refer to section “7.5 CHANGING THE GPS TIME” for details. 17.6 TIME AREA This menu item sets the clock to show UTC time or local time with the offset. Refer to section “7.6 CHANGING THE TIME LOCATION” for details. 17.7 TIME FORMAT This menu item allows setting the clock to show time in 12-hour or 24-hour format. Refer to section “7.7 CHANGING THE TIME FORMAT” for details. 17.8 UNITS OF MEASURE This section allows setting the display units of the speed, distance and altitude. Press and hold SELECT UNITS OF MEASURE SELECT     key ( / key) ( key) ( / key) ( key) 1. Press the CH▼/CH▲ key to select the item GPS SETUP UNITS OF MEASURE to be set. SPEED kts 2. Press the [SELECT] soft key. DISTANCE nm ALTITUDE ft 3. Press the CH▼/CH▲ key to select the unit. 4. Press the [ENTER] soft key to store the new BACK SELECT setting. 5. Press the CLR key to return to radio operation. 17.9 PINNING This selection is used to enable or disable position updates when the vessel is not underway. The default setting is “OFF”. Press and hold SELECT PINNING ON SELECT     key ( / key) ( key) ( / key) ( key) 1. Press the CH▼/CH▲ key to select “ON” or GPS SETUP PINNING “OFF”. OFF ON ON: When pinning is turned on, the HX890 will not update its position unless the BACK ENTER vessel travels over 10Ft. OFF: Whether the vessel is underway or stopped, the HX890 continuously updates its position. This improves accuracy of the position fix. 2. Press the [ENTER] soft key to save the new setting. 3. Press the CLR key to return to radio operation. 97

17.10 SBAS (Satellite Based Augmentation System) This selection enables or disables SBAS such as WAAS, EGNOS and MSAS as some areas (Australia for example) can have problems with GPS reception with SBAS enabled. The default setting is “ON”. Press and hold SELECT D-GPS ON SELECT     key ( / key) ( key) ( / key) ( key) 1. Press the CH▼/CH▲ key to select “ON” or “OFF”. GPS SETUP D-GPS OFF ON 2. Press the [ENTER] soft key to store the new setting. 3. Press the CLR key to return to radio operation. BACK ENTER 17.11 OUTPUT SENTENCES This selection is used to setup the NMEA output sentences of the HX890. By default, all the NMEA sentences are turned “OFF”. Press and hold SELECT OUTPUT SENTENCES SELECT     key ( / key) ( key) ( / key) ( key) 1. Press the CH▼/CH▲ key to select the desired sentence GPS SETUP OUTPUT SENTENCES type, then press the [SELECT] soft key. GLL ON GGA 2. Press the CH▼/CH▲ key to select “ON” or “OFF”. GSA GSV 3. Press the [ENTER] soft key to save the new setting. RMC ON BACK ENTER 4. Repeat steps 5 through 7 to set the other sentences. 5. Press the CLR key to return to radio operation. 17.12 LOGGER INTERVAL Press and hold SELECT LOGGER INTERVAL SELECT     key ( / key) ( key) ( / key) ( key) 1. Press the CH▼/CH▲ key to select the desired time and GPS SETUP LOGGER INTERVAL press the [ENTER] soft key. 5sec 15sec Note: Log time for each logger interval setting 30sec 1min 5 sec: Aprox. 8 hours 5min BACK ENTER 15 sec: Aprox. 25 hours 30 sec: Aprox. 50 hours 1 min: Aprox. 100 hours 5 min: Aprox. 500 hours 2. Press the CLR key to return to radio operation. 98

17.13 LOG ERASE Press and hold SELECT LOG ERASE SELECT     key ( / key) ( key) ( / key) ( key) 1. Press the CH▼/CH▲ key to select “CANCEL” or “OK”, then GPS SETUP LOG ERASE CANCEL press the [ENTER] soft key. OK 2. Press the CLR key to return to radio operation. BACK ENTER 17.14 SUMMARY OF THE GPS SETUP Item Description Default Value GPS ON/OFF Turns on or off the GPS receiver ON POWER SAVE Selects the power save mode of the GPS AUTO unit DIRECTION Selects the compass direction to be COURSE UP displayed LOCATION FORMAT Selects the coordinate system to be ddd°mm.mmm displayed TIME OFFSET Sets the offset time from the UTC (avail- 00:00 able only when “LOCAL” is selected in the item “TIME AREA”) TIME AREA Selects the time location to be displayed, UTC from UTC or local TIME FORMAT Selects the time format to be displayed, 24H 12-hour or 24-hour (fixed to “24H” when “UTC” is selected in the item “TIME AREA”) UNITS OF MEASURE Selects the unit of measure when display- SPEED: kts ing speed, distance, and altitude DISTANCE: nm ALTITUDE: ft PINNING Turns GPS position updates ON or OFF OFF for vessel not underway D-GPS Turns use of SBAS ON OUTPUT Selects a sentence to be output to the OFF SENTENCES USB terminal LOGGER INTERVAL Selects the logging interval time 1 min LOG ERASE Erases the log data − 18. ATIS SETUP (HX890E only) The HX870E supports the ATIS (Automatic Transmitter Identification System) used in Inland waterways in Europe. When enabled ATIS mode transmits a unique ATIS code each time the PTT switch is released at the end of a trans- mission. Users should check with their local marine regulatory authority in their country for assistance in obtaining an ATIS code. 99

18.1 ATIS CODE PROGRAMMING Press and hold ATIS SETUP SELECT ATIS CODE SELECT     key ( / key) ( key) ( / key) ( key) 1. Press the ◄/► key to select the first numer- ATIS CODE INPUT ATIS al of your ATIS, then press the [SELECT] 1st: ---------- soft key to step to the next numeral. ATIS CODE INPUT 2. If the ATIS number has been entered twice, 12 34 567890 ATIS Delete 1st: 9876543210 continue with step 5 to set your ATIS number BACK FINISH SELECT (ten digits). ATIS CODE INPUT 12 34 567890 ATIS Delete 3. If a mistake was made entering in the ATIS, BACK FINISH SELECT 1st: ********** press the CH▼/CH▲/◄/► key to select 2st: 0123456789 ATIS CODE INPUT “<-” or “->”, press the [SELECT] soft key 12 34 567890 ATIS Delete until the wrong number is selected, then BACK FINISH SELECT STORED ATIS! perform step 1. 0123456789 4. When finished programming the number, OK press the [FINISH] soft key. The Radio will ask you to input the ATIS number again. Perform steps 1 through 4 above. 5. After the number has been input a second time, press the [FINISH] soft key to store the ATIS number in memory. 6. Press the [OK] soft key to return to radio operation. 18.2 ATIS CH GROUP The HX870E ATIS feature may be enabled or disabled for each channel group. Press and hold ATIS SETUP SELECT ATIS GROUP SELECT     key ( / key) ( key) ( / key) ( key) 1. Press the CH▼/CH▲ key to select the chan- ATIS SETUP ATIS GROUP nel group (International, Canadian, or USA) USA INTL you wish to change the setting, and press CAN ATIS SETUP the [SELECT] soft key. INTL OFF 2. Press the CH▼/CH▲ key to select “ON” or BACK SELECT ON “OFF”. ATIS SETUP ATIS GROUP 3. Press the [SELECT] soft key to save the USA BACK ENTER INTL ON new setting. CAN 4. If you want to set the ATIS feature to another channel group, repeat step 1 through 3. BACK SELECT 5. Press the CLR key to return to radio opera- tion. 100

19. MAINTENANCE 19.1 GENERAL The inherent quality of the solid-state components in STANDARD HORIZON radios will provide many years of continuous use. Take the following precau- tions to prevent damage to the radio: • Never key the microphone unless an antenna or suitable dummy load is connected to the transceiver • Use only STANDARD HORIZON-approved accessories and replacement parts. 19.2 FACTORY SERVICE In the unlikely event that the radio fails to perform or needs servicing, please contact one of following: In USA and Canada Standard Horizon Attention Marine Repair Department 6125 Phyllis Drive, Cypress, California 90630, U.S.A. Telephone (800) 366-4566 In Europe Yaesu (UK) Ltd Unit 12, Sun Valley Business Park, Winnall Close Winchester, Hampshire, SO23 0LB, U. K. Telephone +44 (0)1962 866667 In Other Countries Contact the dealer or the distributor. 19.3 Reset the USER MMSI and ATIS CODE If the MMSI number and ATIS code (HX890E only) need to be reset. Please contact Standard Horizon to obtain the required reset codes. 19.3.1 To request the Reset Code Contact Standard Horizon and confirm the following required information. • The Information Necessary to obtain the Reset Code • Model name • Serial number • Current MMSI number and ATIS code (To check the MMSI number and ATIS code, refer to 11.2 MARITIME MOBILE SERVICE IDENTITY (MMSI) or 18.ATIS SETUP (HX890E only). • Request codes for the MMSI number and the ATIS code 101

(See “Checking the Request code” below). • Contact Information • USA/Canada E-mail: marinetech@yaesu.com Telephone: (800) 767-2450 • Europe E-mail: service@yaesu.co.uk Telephone: +44 (0)1962 866667 19.3.2 Checking the Request code Press and hold CONFIGURATION SELECT RESET SELECT     key ( / key) ( key) ( / key) ( key) 1. Press the CH▼/CH▲ key to select “USER CONFIGURATION RESET MMSI” or “ATIS CODE”, then press the WAYPOINT & GPS CONFIGURATION [SELECT] soft key. FACTORY CONFIGURATION USER MMSI The RESET screen will appear. USER MMSI RESET ATIS CODE REQUEST CODE BACK SELECT 2. Press the [SELECT] soft key again. PASSWORD The request code will be displayed. CONFIGURATION BACK SELECT USER MMSI RESET <Request Code> XXXXXXX-XXXXXXX BACK NOTE When resetting both “USER MMSI and “ATIS CODE”, both request codes are required. 19.3.3 Resetting the USER MMSI and ATIS codes Here is the procedure for resetting the USER MMSI and ATIS codes after obtaining the reset codes. 1. The RESET screen is displayed on step 1 in “Checking the Request code”. 2. Press the CH▼/CH▲ key to select “PASSWORD", then CONFIGURATION USER MMSI RESET press the [SELECT] soft key. REQUEST CODE PASSWORD The password input screen will appear. BACK SELECT 102


Document Created: 2018-05-11 11:26:16
Document Modified: 2018-05-11 11:26:16
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC