Test Report 2

FCC ID: K6630443X3D

Test Report

Download: PDF
FCCID_2127079

RFT Issue Date: 09 Nov. 2013 Report No.: ERY1311P09R1 Model: GX2200 TEST REPORT For Marine Transceiver/MATRIX AIS/GPS In conformity with FCC CFR 47 Part80 Subpart E RSS-282 Issue5 (RSS-Gen Issue 3) Model : GX2200 FCC ID : K6630443X3D IC : 511B-30443X3D Test Item : Marine Transceiver/MATRIX AIS/GPS Report No. : ERY1311P09R1 Issue Date : 09 Nov. 2013 Prepared for YAESU MUSEN CO., LTD. Tennozu Parkside Building 2-5-8 Higashi-shinagawa, Shinagawa-ku, Tokyo 140-0002 Japan Prepared by RF Technologies Ltd. 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645 FAX: +81+(0)45- 534-0646 This report shall not be reproduced, except in full, without the written permission of RF Technologies Ltd. The test results in this report apply only to the sample tested. RF Technologies Ltd. is managed to ISO17025 and has the necessary knowledge and test facilities for testing according to the referenced standards. RF Technologies Ltd. Page 1 of 15 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 09 Nov. 2013 Report No.: ERY1311P09R1 Model: GX2200 Table of contents 1 General information ...................................................................................................................... 3 1.1 Product description ................................................................................................................................................ 3 1.2 Test(s) performed/ Summary of test result ............................................................................................................ 3 1.3 Test facility ............................................................................................................................................................ 4 1.4 Measurement uncertainty ....................................................................................................................................... 4 1.5 Summary of test results.......................................................................................................................................... 5 1.6 Setup of equipment under test (EUT) .................................................................................................................... 5 1.6.1 Test configuration of EUT ............................................................................................................................. 5 1.6.2 Operating condition: ...................................................................................................................................... 5 1.6.3 Setup diagram of tested system...................................................................................................................... 6 1.7 Equipment modifications ....................................................................................................................................... 6 1.8 Deviation from the standard .................................................................................................................................. 6 2 Test procedure and test data ........................................................................................................ 7 2.1 Radiated spurious emissions (Transmitter test) ..................................................................................................... 7 2.2 Radiated emissions (Receiver test) ...................................................................................................................... 11 3 Test setup photographs ............................................................................................................... 14 3.1 Radiated emissions .............................................................................................................................................. 14 4 List of utilized test equipment / calibration .............................................................................. 15 History Report No. Date Revisions Issued By ERY1311P09R1 09 Nov. 2013 Initial Issue T.Kato RF Technologies Ltd. Page 2 of 15 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

Issue Date: 09 Nov. 2013 Report No.: ERY131 IPOOR1 Model: GX2200 1 General information 1.1 Product description Test item : Marine Transceiver/MATRIX AIS/GPS Manufacturer : YAESU MUSEN CO., LTD. Address :43 Utsuroda, Morijuku, Sukagawa—shi, Fukushima—ken 962—0001 Japan Model : GX2200 FCC ID : K6630443X3D 1C : 511B—30443X3D Serial number : L41B000001 Operating frequency : 156.025 — 163.275 MHz Output power :25 W (High) / 1 W (Low) nominal Emission designator : 16K0G3E (Voice), 16K0G2B (DSC) Software version : N/A Hardware version : N/A Highest operating frequency : 9.8304 MHz Receipt date of EUT : 06 Nov. 2013 Nominal power source voltages : 13.8 Vde 1.2 Test(s) performed/ Summary of test result Test specification(s) : FCC CFR 47. Part 80 subpart E : RSS—182 Issue 5 (RSS—Gen Issue 3) Test method(s) : TIS—603—D (FCC Part 80) : ANSI C63.4: 2003 (RSS) Test(s) started : 09 Nov. 2013 Test(s) completed : 09 Nov. 2013 Purpose of test(s) : Certification / Class II permissive change Summary oftest result : Complied Note: The above judgment is only based on the measurement data andit does not include the measurement uncertainty. Accordingly, the statement below is applied to the test result. The EUT complies with the limit required in the standard in case that the margin is not less than the measurement uncertainty in the Laboratory. Compliance of the EUT is more probable than non—complianceis case that the margin is less than the measurement uncertainty in the Laboratory. Test engineer __ILa T. Kato EMC testing Department Reviewer y ~ . K. Ohnishi Manager EMC testing Department RF Technologies Ltd. Page 3 of 15 472, Nippa—cho, Kohoku—ku, Yokohama, 223—0057, Japan Telephone: +81+(0)45— 534—0645, FAX: +8 1+(0)45— 534—0646, Web: http://www.rft.jp

RFT Issue Date: 09 Nov. 2013 Report No.: ERY1311P09R1 Model: GX2200 1.3 Test facility The Federal Communications Commission has reviewed the technical characteristics of the test facilities at RF Technologies Ltd., located in 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan, and has found these test facilities to be in compliance with the requirements of 47 CFR Part 15, section 2.948, per October 1, 2010. The description of the test facilities has been filed under registration number 319924 at the Office of the Federal Communications Commission. The facility has been added to the list of laboratories performing these test services for the public on a fee basis. The list of all public test facilities is available on the Internet at http://www.fcc.gov. Registered by Industry Canada (IC): The registered facility number is as follows; Test site No. 1 (Semi-Anechoic chamber 3m): 6974A-1 Accredited by National Voluntary Laboratory Accreditation Program (NVLAP) for the emission tests stated in the scope of the certificate under Certificate Number 200780-0 This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. 1.4 Measurement uncertainty The treatment of uncertainty is based on the general matters on the definition of uncertainty in “Guide to the expression of uncertainty in measurement (GUM)” published by ISO. The Lab’s uncertainty is determined by referring UKAS Publication LAB34: 2002 “The Expression of Uncertainty in EMC Testing” and CISPR16-4-2: 2011 “Uncertainty in EMC Measurements”. The uncertainty of the measurement result in the level of confidence of approximately 95% (k=2) is as follows; Conducted emission: ± 3.4 dB (10 kHz - 30 MHz) Radiated emission (9 kHz - 30 MHz): ± 3.3 dB Radiated emission (30 MHz - 200 MHz): ± 5.0 dB Radiated emission (200 MHz - 1000 MHz): ± 6.2 dB Radiated spurious emission (30 MHz - 1000 MHz): ± 1.8 dB Radiated spurious emission (1 GHz – 18 GHz): ± 2.8 dB RF Technologies Ltd. Page 4 of 15 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 09 Nov. 2013 Report No.: ERY1311P09R1 Model: GX2200 1.5 Summary of test results Section Section in Requirement Result in Standard this report Tx Radiated spurious emissions (30 to 1700 MHz) * FCC 80.211(f)(3) Complied 2.1 RSS-182 Sec. 7.11 Rx Radiated emissions (30 – 1000 MHz) ** Complied 2.2 RSS-Gen Sec. 4.10 * Maximum frequency of transmitter is 163.275 MHz ** Maximum internal operating frequency is 9.8304 MHz. 1.6 Setup of equipment under test (EUT) 1.6.1 Test configuration of EUT Equipment(s) under test No. Item Manufacture Model No. Serial No. A Marine Transceiver YAESU MUSEN CO., LTD. GX2200 L41B000001 /MATRIX AIS/GPS B Microphone - - - *Microphone is a part of the EUT. Support Equipment(s) No. Item Manufacture Model No. Serial FCC ID No. C Remote Station Microphone Vertex Standard Co., Ltd. CMP30 0J150202 - - Connected cable(s) No. Item Identification Cable Ferrite Length (Manu.etc.) Shielded Core [m] 1 Mic cable of EUT YAESU MUSEN CO., LTD. Yes No 0.5 2 DC cable YAESU MUSEN CO., LTD. No No 1.3 3 23-Foot Routing cable YAESU MUSEN CO., LTD. Yes Yes 7.0 4 Mic. cable of CMP30 YAESU MUSEN CO., LTD. Yes No 0.5 1.6.2 Operating condition: Tx Mode: The EUT transmit Tx power in 16 ch. (Tx power level are two mode. ( Hi:25W, Low:1W) Rx Mode: The EUT is in receiving mode at 16/70 ch. RF Technologies Ltd. Page 5 of 15 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 09 Nov. 2013 Report No.: ERY1311P09R1 Model: GX2200 1.6.3 Setup diagram of tested system A: Marine Transceiver 1 (EUT) 3 4 2 B: C: Microphone Remote (EUT) Station Mic. DC 13.8V 1.7 Equipment modifications No modifications have been made to the equipment in order to achieve compliance with the applicable standards described in clause 1.2. 1.8 Deviation from the standard No deviations from the standards described in clause 1.2. RF Technologies Ltd. Page 6 of 15 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 09 Nov. 2013 Report No.: ERY1311P09R1 Model: GX2200 2 Test procedure and test data 2.1 Radiated spurious emissions (Transmitter test) Test setup Test setup was implemented according to the method of ANSI C63.4: 2003 clause 6 “General requirements for EUT equipment arrangements and operation”, clause 8.2 and Annex H.3 “Radiated emission measurements setup”. Test procedure Measurement procedures were implemented according to the method of TIA-603-C clauses 2.2.12.2. a) Antenna terminal of the EUT is terminated with a nonradiating load. b) Adjust the spectrum analyzer as below. 1) RBW = 10 kHz (below 1 GHz), 1 MHz (above 1 GHz) 2) VBW = 300 kHz (below 1 GHz), 3 MHz (above 1 GHz) 3) Sweep speed slow enough to maintain measurement 4) Detector mode : Peak c) Place the EUT on the turntable. The EUT set Tx ON in max power level d) For each spurious frequency that was found, the test antenna is raised and lowered from 1 to 4 m to obtain a maximum level on the spectrum alnalyzer. Then the turntable should be rotated 360 deg to determine the maximum reading. e) Repeat step d) for each spurious frequency with the test antenna polarized vert/hori. f) The EUT was replaced with substitution antenna and signal generator. g) Feed the substitution antenna at the transmitter end with signal generator connected to the antenna by means od a nonradiating cable. With the antennas at both ends horizontally polarized, and with the signal generator tuned to a paticular spurious frequency, raise and lower the test antenna to obtain a maximum reading at the spestrum analyzer. Adjust the level of the signal generator output until the previously recorded maximum reading for this set of conditions is obtained. This should be done carefully repeating the adjustment of the test antenna and generator output. h) Repeat step g) with both antennas vertically polarized for each spurious frequency. i) Calculate power in dBm erp as below. Spurious emission level = Antenna input level [dBm] + Substitution antenna gain [dBd] Applicable rule and limitation Part 80.211 (f) (3) Radiated emission limits Limit Level = Po [dBm] – (43 + 10 log (Po [W])) = - 13 [dBm erp] Test results - Complied with requirement Test equipment used (refer to List of utilized test equipment) AC01 CL11 TR06 PR15 BI05 LA07 CL30 CL31 PR12 DR01 RF Technologies Ltd. Page 7 of 15 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 09 Nov. 2013 Report No.: ERY1311P09R1 Model: GX2200 Test Data Operating mode: Tx mode (16ch / 25W) Measurement distance: 3 m [Spurious emission level] Frequency Result Limit Margin No. Ant. [MHz] [dBµV/m] [dBµV/m] [dB] 1 313.6 -35.9 -13.0 22.9 Hori. 2 470.4 -39.6 -13.0 26.6 Hori. 3 627.2 -44.1 -13.0 31.1 Hori. 4 784.0 -38.1 -13.0 25.1 Hori. 5 940.8 -39.6 -13.0 26.6 Hori. 6 1097.6 -51.2 -13.0 38.2 Hori. 7 1254.4 -51.7 -13.0 38.7 Hori. 8 1411.2 -45.1 -13.0 32.1 Hori. 9 1568.0 -52.0 -13.0 39.0 Hori. 10 313.6 -48.2 -13.0 35.2 Vert. 11 470.4 -45.6 -13.0 32.6 Vert. 12 627.2 -38.2 -13.0 25.2 Vert. 13 784.0 -38.7 -13.0 25.7 Vert. 14 940.8 -42.9 -13.0 29.9 Vert. 15 1097.6 -47.0 -13.0 34.0 Vert. 16 1254.4 -47.1 -13.0 34.1 Vert. 17 1411.2 -43.6 -13.0 30.6 Vert. 18 1568.0 -46.0 -13.0 33.0 Vert. [Chart] Note: 156.8 MHz is Tx carrier frequency. RF Technologies Ltd. Page 8 of 15 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 09 Nov. 2013 Report No.: ERY1311P09R1 Model: GX2200 Operating mode: Tx mode (16ch / 1W) Measurement distance: 3 m [Spurious emission level] Frequency Result Limit Margin No. Ant. [MHz] [dBµV/m] [dBµV/m] [dB] 1 313.6 -41.3 -13.0 28.3 Hori. 2 470.4 -40.8 -13.0 27.8 Hori. 3 627.2 -57.1 -13.0 44.1 Hori. 4 784.0 -46.7 -13.0 33.7 Hori. 5 940.8 -52.4 -13.0 39.4 Hori. 6 1097.6 -59.2 -13.0 46.2 Hori. 7 1254.4 -55.5 -13.0 42.5 Hori. 8 1411.2 -49.0 -13.0 36.0 Hori. 9 1568.0 -56.1 -13.0 43.1 Hori. 10 313.6 -51.5 -13.0 38.5 Vert. 11 470.4 -48.3 -13.0 35.3 Vert. 12 627.2 -57.2 -13.0 44.2 Vert. 13 784.0 -46.4 -13.0 33.4 Vert. 14 940.8 -53.4 -13.0 40.4 Vert. 15 1097.6 -58.8 -13.0 45.8 Vert. 16 1254.4 -51.5 -13.0 38.5 Vert. 17 1411.2 -47.0 -13.0 34.0 Vert. 18 1568.0 -54.5 -13.0 41.5 Vert. RF Technologies Ltd. Page 9 of 15 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 09 Nov. 2013 Report No.: ERY1311P09R1 Model: GX2200 [Chart] Note: 156.8 MHz is Tx carrier frequency. Tested Date: 09 Nov. 2013 Temperature: 20 degC Humidity: 41 % Atmos. Press: 1029 hPa RF Technologies Ltd. Page 10 of 15 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 09 Nov. 2013 Report No.: ERY1311P09R1 Model: GX2200 2.2 Radiated emissions (Receiver test) Test setup Test setup was implemented according to the method of ANSI C63.4: 2003 clause 6 “General requirements for EUT equipment arrangements and operation”, clause 8.2 and Annex H.3 “Radiated emission measurements setup”. Semi anechoic room 1-4m Rx Antenna EUT 3.0 m 0.8 m Pre-amplifier Test Receiver Test procedure Measurement procedures were implemented according to the method of ANSI C63.4: 2003 clauses 8.2. The EUT is place on a non-conducted table which is 0.8 m height from a ground plane and the measurement antenna to EUT distance is 3 meters. The turn table is rotated for 360 degrees to determine the maximum emission level. The antenna height scanned between 1 m and 4 m, and the antenna rotated to repeat the measurements for both the horizontal and vertical antenna polarizations. The spectrum analyzer and receiver are set to the followings; RBW=100 kHz, VBW= 300 kHz Final measurement is carried out with a receiver RBW of 120 kHz (QP) Applicable rule and limitation RSS-Gen clauses 6.1: Radiated emission limits Frequency Field Strength Measurement Field Strength [MHz] [µV/m] Distance [m] [dBµV/m] 30 – 88 100 3 40.0 88 –216 150 3 43.5 216 – 960 200 3 46.0 Above 960 500 3 53.9 In the emission table above, the tighter limit applies at the band edges. The emission limits shown in the above table are based on measurements employing a quasi-peak detector. RF Technologies Ltd. Page 11 of 15 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 09 Nov. 2013 Report No.: ERY1311P09R1 Model: GX2200 Test results - Complied with requirement Test equipment used (refer to List of utilized test equipment) AC01 CL11 TR06 PR15 BI05 LA07 Test Data Operating mode: Rx mode 16ch Measurement distance: 3 m [Emission level] Frequency Reading Factor Loss Gain Result Limit Margin No. Ant. [MHz] [dBµV] [dB/m] [dB] [dB] [dBµV/m] [dBµV/m] [dB] 1 135.100 43.3 14.3 8.4 30.1 35.9 43.5 7.6 Hori. 2 200.875 38.7 11.6 9.0 30.0 29.3 43.5 14,2 Hori. 3 229.625 42.0 11.7 9.4 29.9 33.2 46.0 12.8 Hori. 4 270.200 44.6 12.5 9.8 29.9 37.0 46.0 9.0 Hori. 5 405.300 40.0 15.8 11.1 29.8 37.1 46.0 8.9 Hori. 6 459.250 34.7 16.9 11.5 29.7 33.4 46.0 12.6 Hori. 7 540.400 39.4 18.2 12.0 29.5 40.2 46.0 5.9 Hori. 8 810.600 35.7 20.9 13.1 30.4 39.3 46.0 6.7 Hori. 9 135.100 48.2 14.3 8.4 30.1 40.8 43.5 2.7 Vert. 10 200.875 40.4 11.6 9.0 30.0 31.0 43.5 12.5 Vert. 11 540.392 39.2 18.2 12.0 29.5 39.9 46.0 6.1 Vert. [Calculation sample] Correction Factor [dB/m] = FACTOR [dB/m] + LOSS [dB] – GAIN [dB] RESULT [dBµV/m] = READING [dBµV] + Correction Factor [dB/m] [Chart] RF Technologies Ltd. Page 12 of 15 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 09 Nov. 2013 Report No.: ERY1311P09R1 Model: GX2200 Operating mode: Rx mode 70ch Measurement distance: 3 m [Emission level] Frequency Reading Factor Loss Gain Result Limit Margin No. Ant. [MHz] [dBµV] [dB/m] [dB] [dB] [dBµV/m] [dBµV/m] [dB] 1 134.825 43.4 14.2 8.4 30.1 35.9 43.5 7.6 Hori. 2 229.625 42.1 11.7 9.4 29.9 33.3 46.0 12.7 Hori. 3 269.650 44.7 12.5 9.8 29.9 37.1 46.0 8.9 Hori. 4 404.475 41.1 15.8 11.1 29.8 38.2 46.0 7.8 Hori. 5 539.300 40.1 1.2 12.0 29.5 40.8 46.0 5.2 Hori. 6 674.124 33.7 19.5 12.6 29.8 36.0 46.0 10.0 Hori. 7 808.950 35.4 20.9 13.1 30.4 39.0 46.0 7.0 Hori. 8 134.825 48.1 14.2 8.4 30.1 40.6 43.5 2.9 Vert. 9 200.874 40.2 11.6 9.0 30.0 30.8 43.5 12.7 Vert. 10 539.300 39.7 18.2 12.0 29.5 40.4 46.0 5.6 Vert. [Calculation sample] Correction Factor [dB/m] = FACTOR [dB/m] + LOSS [dB] – GAIN [dB] RESULT [dBµV/m] = READING [dBµV] + Correction Factor [dB/m] [Chart] Tested Date: 09 Oct. 2013 Temperature: 20 degC Humidity: 41 % Atmos. Press: 1029 hPa RF Technologies Ltd. Page 13 of 15 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 09 Nov. 2013 Report No.: ERY1311P09R1 Model: GX2200 3 Test setup photographs 3.1 Radiated emissions RF Technologies Ltd. Page 14 of 15 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 09 Nov. 2013 Report No.: ERY1311P09R1 Model: GX2200 4 List of utilized test equipment / calibration RFT Kind of Equipment and Calibration Manufacturer Model No. Serial Number Calibrated until ID No. Precision Date AC01(EM) Anechoic Chamber (1st test room) JSE 203397C - 2013/4/20 2014/4/30 AC01(EG) Anechoic Chamber (1st test room) JSE 203397C - 2012/11/17 2013/11/30 VHA9103 BI05 Biconical Antenna SCHWARZBECK 91032894 2012/12/3 2013/12/31 & BBA9106 CL11 Antenna Cable for RE RFT - - 2013/10/22 2014/10/31 CL30 RF Cable 5 m SUHNER SUCOFLEX104PE MY3599 2013/8/10 2014/8/31 CL31 RF Cable 1 m Junkosha MWX221 1303S118 2013/10/17 2014/10/31 DH01 DRG Horn Antenna A.H. Systems SAS-571 785 2012/1/27 2014/1/31 LA07 Logperiodic Antenna SCHWARZBECK VUSLP9111B 102 2012/12/3 2013/12/31 PR12 Pre. Amplifier (1-26G) Agilent Technologies 8449B 3008A02513 2013/1/15 2014/1/31 PR15 Pre. Amplifier Anritsu MH648A 6201156141 2013/6/11 2014/6/30 Test Receiver TR06 Rohde & Schwarz ESU26 100002 2013/9/10 2014/9/30 (F/W : 3.93 SP2) The measuring equipment, which was utilized in performing the tests documented herein, has been calibrated in accordance with the manufacturer's recommendations for utilizing calibration equipment, which is traceable to recognized national standards. RF Technologies Ltd. Page 15 of 15 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp


Document Created: 2019-11-17 21:40:11
Document Modified: 2019-11-17 21:40:11
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC