Test Report JBP Rev 1

FCC ID: K6620621X50

Test Report

Download: PDF
FCCID_2622986

Issue Date: 21 May. 2015 Report No.: ERY1505P21R1 Model: FT-410 TEST REPORT For HF Transceiver In conformity with FCC CFR 47 Part15 Subpart B (ITE) Model : FT-410 FCC ID : K6620621X50 Test Item : HF Transceiver Report No. : ERY1505P21R1 Issue Date : 21 May. 2015 Prepared for YAESU MUSEN CO., LTD. Tennozu Parkside Building 2-5-8 Higashi-Shinagawa, Shinagawa-ku, Tokyo 140-0002 JAPAN Prepared by SGS RF Technologies Inc. 3-5-23, Kiyatamata, Tsuzuki-ku, Yokohama, 224-0021, Japan Telephone: +81+(0)45- 550-3520 FAX: +81+(0)45- 592-7506 SGS RF Technologies Inc. Page 1 of 14 3-5-23, Kitayamata, Tsuzuki-ku, Yokohama, 224-0021, Japan Telephone: +81+(0)45- 550-3520, FAX: +81+(0)45- 592-7506, Web: http://www.rf-test.jp

Issue Date: 21 May. 2015 Report No.: ERY1505P21R1 Model: FT-410 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS RF Technologies Inc. is managed to ISO17025 and has the necessary knowledge and test facilities for testing according to the referenced standards. The test results in this report apply only to the sample tested. SGS RF Technologies Inc. Page 2 of 14 3-5-23, Kitayamata, Tsuzuki-ku, Yokohama, 224-0021, Japan Telephone: +81+(0)45- 550-3520, FAX: +81+(0)45- 592-7506, Web: http://www.rf-test.jp

Issue Date: 21 May. 2015 Report No.: ERY1505P21R1 Model: FT-410 Table of contents 1 General information ...................................................................................................................... 4 1.1 Product description ................................................................................................................................................ 4 1.2 Test(s) performed/ Summary of test result ............................................................................................................ 4 1.3 Test facility ............................................................................................................................................................ 5 1.4 Measurement uncertainty ....................................................................................................................................... 5 1.5 Summary of test results.......................................................................................................................................... 6 1.6 Setup of equipment under test (EUT) .................................................................................................................... 6 1.6.1 Test configuration of EUT ............................................................................................................................. 6 1.6.2 Operating condition: ...................................................................................................................................... 6 1.6.3 Setup diagram of tested system...................................................................................................................... 7 1.7 Equipment modifications ....................................................................................................................................... 7 1.8 Deviation from the standard .................................................................................................................................. 7 2 Test procedure and test data ........................................................................................................ 8 2.1 Radiated emissions ................................................................................................................................................ 8 2.2 AC power line conducted emissions .................................................................................................................... 11 3 Test setup photographs ............................................................................................................... 13 3.1 Radiated emissions .............................................................................................................................................. 13 3.2 AC power line conducted emissions .................................................................................................................... 13 4 List of utilized test equipment / calibration .............................................................................. 14 History Report No. Date Revisions Issued By ERY1505P08R1 08 May. 2015 Initial Issue T.Kato ERY1505P21R1 21 May. 2015 Revise the year of ANSI standard (Sec 1.2) T.Kato SGS RF Technologies Inc. Page 3 of 14 3-5-23, Kitayamata, Tsuzuki-ku, Yokohama, 224-0021, Japan Telephone: +81+(0)45- 550-3520, FAX: +81+(0)45- 592-7506, Web: http://www.rf-test.jp

Issue Date: 21 May. 2015 Report No.: ERY1505P2IR1 Model: FT—410 1 General information 1.1 Product description Test item : HF Transceiver Manufacturer : YAESU MUSEN CO., LTD. Address : 43 Utsuroda, Morijuku, Sukagawa—shi, Fukushima—ken 962—0001 JAPAN Model : FT—410 FCC ID : K6620621X50 Serial number : 5F00015 Hardware version : SPPO1.02 Software version : SPPO1 Highest internal operating Freq. : 368.64 MHz Receipt date of EUT : 17 Apr. 2015 Nominal power source voltages : DC 13.8 V (This is supplied AC/DC power supply) 1.2 Test(s) performed/ Summary of test result Test specification(s) : FCC CFR 47 Part 15 Subpart B (01 Oct. 2014) Test method(s) : ANSI C63.4: 2009 Test(s) started : 01 May. 2015 Test(s) completed : 07 May. 2015 Purpose of test(s) : Certification as the peripheral of class B personal computer Summary oftest result : Complied Note: The above judgmentis only based on the measurement data and it does not include the measurement uncertainty. Accordingly, the statement below is applied to the test result. The EUT complies with the limit required in the standard in case that the margin is not less than the measurement uncertainty in the Laboratory. Compliance of the EUT is more probable than non—compliance is case that the margin is less than the measurement uncertainty in the Laboratory. Test engineer f __{kas ~ T. Kato EMC testing Department Reviewer L.. Onioha K. Onishi Manager EMC testing Department SGS RF Technologies Inc. Page 4 of 14 3—5—23, Kitayamata, Tsuzuki—ku, Yokohama, 224—0021, Japan Telephone: +81+(0)45— 550—3520, FAX: +81+(0)45— 592—7506, Web: http://www.rf—test.jp

Issue Date: 21 May. 2015 Report No.: ERY1505P21R1 Model: FT-410 1.3 Test facility The Federal Communications Commission has reviewed the technical characteristics of the test facilities at SGS RF Technologies Inc., located in 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan, and has found these test facilities to be in compliance with the requirements of 47 CFR Part 15, section 2.948, per October 1, 2014. The description of the test facilities has been filed under registration number 319924 at the Office of the Federal Communications Commission. The facility has been added to the list of laboratories performing these test services for the public on a fee basis. The list of all public test facilities is available on the Internet at http://www.fcc.gov. Registered by Industry Canada (IC): The registered facility number is as follows; Test site No. 1 (Semi-Anechoic chamber 3m): 6974A-1 Accredited by National Voluntary Laboratory Accreditation Program (NVLAP) for the emission tests stated in the scope of the certificate under Certificate Number 200780-0 This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. 1.4 Measurement uncertainty The treatment of uncertainty is based on the general matters on the definition of uncertainty in “Guide to the expression of uncertainty in measurement (GUM)” published by ISO. The Lab’s uncertainty is determined by referring UKAS Publication LAB34: 2002 “The Expression of Uncertainty in EMC Testing” and CISPR16-4-2: 2011 “Uncertainty in EMC Measurements”. The uncertainty of the measurement result in the level of confidence of approximately 95% (k=2) is as follows; Conducted emission: ± 3.4 dB (150 kHz - 30 MHz) Radiated emission (9 kHz - 30 MHz): ± 3.3 dB Radiated emission (30 MHz - 200 MHz): ± 5.0 dB Radiated emission (200 MHz - 1000 MHz): ± 6.2 dB Radiated emission (1 GHz - 6 GHz): ± 4.7 dB SGS RF Technologies Inc. Page 5 of 14 3-5-23, Kitayamata, Tsuzuki-ku, Yokohama, 224-0021, Japan Telephone: +81+(0)45- 550-3520, FAX: +81+(0)45- 592-7506, Web: http://www.rf-test.jp

Issue Date: 21 May. 2015 Report No.: ERY1505P21R1 Model: FT-410 1.5 Summary of test results Section Section in Requirement Result in specification this report Radiated emissions (30 to 2000 MHz) (*) 15.109 Complied 2.1 AC power line conducted emissions 15.107 Complied 2.2 (*) The highest internal operating frequency is 368.64 MHz 1.6 Setup of equipment under test (EUT) 1.6.1 Test configuration of EUT Equipment(s) under test No. Item Manufacture Model No. Serial No. A HF Transceiver YAESU MUSEN CO., LTD. FT-410 5F000015 - - - - - Support Equipment(s) No. Item Manufacture Model No. Serial No. B DC Power Supply YAESU MUSEN CO., LTD. FP-1030A 1412167017 C Hand Microphone YAESU MUSEN CO., LTD. MH-31B8J 5F000015 D Headphone YAESU MUSEN CO., LTD. YH-77STA YTS03 E External Speaker YAESU MUSEN CO., LTD. MLS-100 064 F USB Interface Unit YAESU MUSEN CO., LTD. SCU-17 17 G PC Panasonic CF-W8GWYAJP 9GKSA91771 H LAN Hub NEC PA-WR8700N- 87N1111286973B0 HP I AC adaptor for Hub NEC AL1-002292-002 - Connected cable(s) No. Item Identification Cable Ferrite Length (Manu.etc.) Shielded Core [m] 1 DC Power cable YAESU MUSEN CO., LTD. No No 2.0 2 Mic. cable YAESU MUSEN CO., LTD. No No 0.6 3 Headphones cable YAESU MUSEN CO., LTD. No No 1.8 4 EXT SPKR cable YAESU MUSEN CO., LTD. No No 1.8 5 TUNER cable YAESU MUSEN CO., LTD. No No 1.1 6 LINER cable YAESU MUSEN CO., LTD. No No 1.2 7 DATA cable YAESU MUSEN CO., LTD. No No 1.6 8 KEY cable YAESU MUSEN CO., LTD. No No 0.5 9 GND cable YAESU MUSEN CO., LTD. No No 2.0 10 CAT cable SANWA SUPPLY INC. No No 1.5 11 USB cable YAESU MUSEN CO., LTD. Yes No 2.0 12 LAN Cable - No No 2.0 DC cable for AC 13 NEC No No 1.3 adaptor 1.6.2 Operating condition: ITE mode: The EUT is connected to PC using CAT cable. SGS RF Technologies Inc. Page 6 of 14 3-5-23, Kitayamata, Tsuzuki-ku, Yokohama, 224-0021, Japan Telephone: +81+(0)45- 550-3520, FAX: +81+(0)45- 592-7506, Web: http://www.rf-test.jp

Issue Date: 21 May. 2015 Report No.: ERY1505P21R1 Model: FT-410 1.6.3 Setup diagram of tested system E: External 1 B: Speaker AC 120V DC Power 60 Hz Supply Load 4 Open 5 Open 6 A: F: 11 7 HF Transceiver 10 USB G: Open 8 (EUT) 9 Interface PC Open Unit 12 2 3 I: 13 H: C: AC LAN Hub D: Hand Adaptor Headphone Microphone AC 120V 60 Hz Note: The signal cable 5 to 8 were connected to no AE by a request from the manufacturer. 50 ohm terminals were connected to the antenna terminals. 1.7 Equipment modifications No modifications have been made to the equipment in order to achieve compliance with the applicable standards described in clause 1.2. 1.8 Deviation from the standard No deviations from the standards described in clause 1.2. SGS RF Technologies Inc. Page 7 of 14 3-5-23, Kitayamata, Tsuzuki-ku, Yokohama, 224-0021, Japan Telephone: +81+(0)45- 550-3520, FAX: +81+(0)45- 592-7506, Web: http://www.rf-test.jp

Issue Date: 21 May. 2015 Report No.: ERY1505P21R1 Model: FT-410 2 Test procedure and test data 2.1 Radiated emissions Test setup Test setup was implemented according to the method of ANSI C63.4 clause 6 “General requirements for EUT equipment arrangements and operation”, clause 8.2 and Annex H.3 “Radiated emission measurements setup”. Semi anechoic room 1-4m Rx Antenna EUT 3.0 m 0.8 m Pre-amplifier Test Receiver Test procedure Measurement procedures were implemented according to the method of ANSI C63.4 clauses 8.2. The EUT is place on a non-conducted table which is 0.8 m height from a ground plane and the measurement antenna to EUT distance is 3 meters. The turn table is rotated for 360 degrees to determine the maximum emission level. The antenna height scanned between 1 m and 4 m, and the antenna rotated to repeat the measurements for both the horizontal and vertical antenna polarizations. The spectrum analyzer and receiver are set to the followings; RBW=100 kHz (up to 1000 MHz) or 1 MHz (above 1000 MHz) , VBW= 300 kHz (up to 1000 MHz) or 3 MHz (above 1000 MHz) Final measurement is carried out with a receiver RBW of 120 kHz (up to 1000 MHz), or 1 MHz (above 1000 MHz). Applicable rule and limitation FCC 15.109 Radiated emissions limits Frequency Field Strength Measurement Field Strength [MHz] [µV/m] Distance [m] [dBµV/m] 30 – 88 100 3 40.0 88 –216 150 3 43.5 216 – 960 200 3 46.0 Above 960 500 3 53.9 In the emission table above, the tighter limit applies at the band edges. The emission limits shown in the above table are based on measurements employing a QP detector (up to 1000 MHz) or AVE/PEAK detector (above 1000 MHz). SGS RF Technologies Inc. Page 8 of 14 3-5-23, Kitayamata, Tsuzuki-ku, Yokohama, 224-0021, Japan Telephone: +81+(0)45- 550-3520, FAX: +81+(0)45- 592-7506, Web: http://www.rf-test.jp

Issue Date: 21 May. 2015 Report No.: ERY1505P21R1 Model: FT-410 Test results - Complied with requirement Test equipment used (refer to List of utilized test equipment) AC01 TR06 CL11 PR15 BA10 CL29 CL30 PR12 DH01 Test software used EMI Ver. 5.6 Calculation method The Correction Factor and Result are calculated as followings. Correction Factor [dB/m] = Ant. Factor [dB/m] + Loss [dB] – Gain [dB] Result [dBµV/m] = Reasding [dBµV] + Correction Factor [dB/m] Test Data Range: 30 - 1000 MHz Frequency Reading Factor Loss Gain Result Limit Margin No. Ant. [MHz] [dBµV] [dB/m] [dB] [dB] [dBµV/m] [dBµV/m] [dB] 1 184.318 41.6 9.0 8.4 30.0 29.0 43.5 14.5 Hori. 2 258.045 45.2 12.7 8.9 29.9 36.9 46.0 9.1 Hori. 3 306.352 30.1 13.6 9.2 29.9 23.0 46.0 23.0 Hori. 4 331.772 35.1 14.3 9.4 29.9 28.9 46.0 17.1 Hori. 5 452.446 25.0 17.2 10.1 29.7 22.6 46.0 23.4 Hori. 6 47.937 39.0 9.5 7.1 30.2 25.4 40.0 14.6 Vert. 7 120.045 45.5 11.6 7.9 30.1 34.9 43.5 8.6 Vert. 8 135.749 42.4 11.7 8.0 30.0 32.1 43.5 11.4 Vert. 9 184.318 45.0 9.0 8.4 30.0 32.4 43.5 11.1 Vert. 10 258.044 42.5 12.7 8.9 29.9 34.2 46.0 11.8 Vert. 11 331.772 32.8 14.3 9.4 29.9 26.6 46.0 19.4 Vert. 12 995.144 29.4 24.3 12.5 30.1 36.1 53.9 17.8 Vert. Range: 1000 - 2000 MHz Reading Reading Result Result Limit Limit Margin Margin Frequency C.Factor No. [MHz] PK AVE [dB/m] PK AVE PK AVE PK AVE Ant. [dBµV] [dBµV] [dBµV/m] [dBµV/m] [dBµV/m] [dBµV/m] [dB] [dB] 1 1000.500 61.1 33.3 -11.8 49.3 21.5 73.9 53.9 24.6 32.4 Hori. 2 1143.493 55.6 32.9 -10.7 44.9 22.2 73.9 53.9 29.0 31.7 Hori. 3 1327.884 58.2 33.2 -10.0 48.2 23.2 73.9 53.9 25.7 30.7 Hori. 4 1659.267 63.7 33.4 -8.6 55.1 24.8 73.9 53.9 18.8 29.1 Hori. 5 1996.050 52.3 30.4 -4.9 47.4 25.5 73.9 53.9 26.5 28.4 Hori. 6 1330.583 60.0 34.4 -9.9 50.1 24.5 73.9 53.9 23.8 29.4 Vert. 7 1660.467 67.1 33.4 -8.5 58.6 24.9 73.9 53.9 15.3 29.0 Vert. 8 1990.950 54.6 30.5 -5.0 49.6 25.5 73.9 53.9 24.3 28.4 Vert. SGS RF Technologies Inc. Page 9 of 14 3-5-23, Kitayamata, Tsuzuki-ku, Yokohama, 224-0021, Japan Telephone: +81+(0)45- 550-3520, FAX: +81+(0)45- 592-7506, Web: http://www.rf-test.jp

Issue Date: 21 May. 2015 Report No.: ERY1505P21R1 Model: FT-410 [Chart] [Test condition] Tested Date: 01 May. 2015 Temperature: 21 degC Humidity: 57 % Atmos. Press: 1017 hPa SGS RF Technologies Inc. Page 10 of 14 3-5-23, Kitayamata, Tsuzuki-ku, Yokohama, 224-0021, Japan Telephone: +81+(0)45- 550-3520, FAX: +81+(0)45- 592-7506, Web: http://www.rf-test.jp

Issue Date: 21 May. 2015 Report No.: ERY1505P21R1 Model: FT-410 2.2 AC power line conducted emissions Test setup Test setup was implemented according to the method of ANSI C63.4 clause 6 “General requirements for EUT equipment arrangements and operation” and Annex H.1 “AC power line conducted emission measurements setup”. Test procedure Measurement procedures were implemented according to the method of ANSI C63.4 clauses 7, clause 13.1.3 and Annex H.2 “AC power line conducted emission measurements”. Exploratory measurements were used the spectrum analyzer to identify the frequency of the emission that has the highest amplitude relative to the limit by operating the EUT in a range of typical modes of operation, cable positions, and with a typical system equipment configuration and arrangement. Final ac power line conducted emission measurements were performed based on the exploratory tests. The EUT cable configuration and arrangement and mode of operation that produced the emission with the highest amplitude relative to the limit are selected for the final measurement. When the measurement value is grater than average limitation the average detection measurements were performed. Applicable rule and limitation §15.107 (b) AC power line conducted limits Frequency of Emission Conducted emissions Limit [dBµV] [MHz] Quasi-peak Average 0.15 - 0.5 66 to 56 * 56 to 46 * 0.5 - 5 56 46 5 - 30 60 50 * Decreases with the logarithm of the frequency. The lower limit applies at the band edges. Test equipment used (refer to List of utilized test equipment) TR06 LN05 CL18 Test software used EMI Ver. 5.6 Calculation method The Correction Factor and Result are calculated as followings. Correction Factor [dB] = ISN Factor [dB] + Loss [dB] Result [dBµV] = Reading [dBµV] + Correction Factor [dB] Test results - Complied with requirement SGS RF Technologies Inc. Page 11 of 14 3-5-23, Kitayamata, Tsuzuki-ku, Yokohama, 224-0021, Japan Telephone: +81+(0)45- 550-3520, FAX: +81+(0)45- 592-7506, Web: http://www.rf-test.jp

Issue Date: 21 May. 2015 Report No.: ERY1505P21R1 Model: FT-410 Test Data [Emission level] Reading Result Limit Frequency C.F. No. QP AV QP AV QP AV Phase Pass/Fail [MHz] [dB] [dBµV] [dBµV] [dBµV] [dBµV] [dBµV] [dBµV] 1 0.15555 18.5 1.4 10.3 28.8 11.7 65.7 55.7 Va Pass 2 0.16295 17.3 1.2 10.3 27.6 11.5 65.3 55.3 Va Pass 3 16.30994 23.3 17.1 10.4 33.7 27.5 60.0 50.0 Va Pass 4 0.15222 18.9 1.5 10.3 29.2 11.8 65.9 55.9 Vb Pass 5 0.16369 17.0 1.2 10.3 27.3 11.5 65.3 55.3 Vb Pass 6 16.36713 25.0 19.1 10.4 35.4 29.5 60.0 50.0 Vb Pass [Chart] [Test condition] Tested Date: 07 May. 2015 Temperature: 21 degC Humidity: 52 % Atmos. Press: 1013 hPa SGS RF Technologies Inc. Page 12 of 14 3-5-23, Kitayamata, Tsuzuki-ku, Yokohama, 224-0021, Japan Telephone: +81+(0)45- 550-3520, FAX: +81+(0)45- 592-7506, Web: http://www.rf-test.jp

Issue Date: 21 May. 2015 Report No.: ERY1505P21R1 Model: FT-410 4 List of utilized test equipment / calibration RFT Kind of Equipment and Calibration Manufacturer Model No. Serial Number Calibrated until ID No. Precision Date AC01(EM) Anechoic Chamber (1st test room) JSE 203397C - 2015/4/18 2016/4/30 AC01(EG) Anechoic Chamber (1st test room) JSE 203397C - 2014/11/24 2015/11/30 BA10 Bilogical Antenna TESEQ CBL6111D 32342 2014/6/9 2015/6/30 CL11 RF Cable for RE RFT - - 2015/3/13 2016/3/31 CL18 RF Cable for CE RFT - - 2015/5/1 2016/5/31 CL29 RF Cable 2 m SUHNER SUCOFLEX104PE 94709 2015/1/26 2016/1/31 CL30 RF Cable 5 m SUHNER SUCOFLEX104PE MY3599 2014/8/28 2015/8/31 DH01 DRG Horn Antenna A.H. Systems SAS-571 785 2014/1/21 2016/1/31 LN05 LISN Kyoritsu KNW-407F 8-1773-2 2014/5/22 2015/5/31 PR12 Pre. Amplifier (1-26G) Agilent Technologies 8449B 3008A02513 2015/1/26 2016/1/31 PR15 Pre. Amplifier Anritsu MH648A 6201156141 2014/6/10 2015/6/30 Test Receiver TR06 Rohde & Schwarz ESU26 100002 2014/9/5 2015/9/30 (F/W : 3.93 SP2) The measuring equipment, which was utilized in performing the tests documented herein, has been calibrated in accordance with the manufacturer's recommendations for utilizing calibration equipment, which is traceable to recognized national standards. SGS RF Technologies Inc. Page 14 of 14 3-5-23, Kitayamata, Tsuzuki-ku, Yokohama, 224-0021, Japan Telephone: +81+(0)45- 550-3520, FAX: +81+(0)45- 592-7506, Web: http://www.rf-test.jp


Document Created: 2015-05-21 16:09:57
Document Modified: 2015-05-21 16:09:57
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC