TEST REPORT

FCC ID: K6620233X40

Test Report

Download: PDF
FCCID_601497

TABLE OF CONTENTS LIST APPLICANT: VERTEX STANDARD CO., LTD. FCC ID: K6620233X40 TEST REPORT CONTAINING: PAGE 1......TEST PROCEDURE PAGE 2......TEST PROCEDURE & CIRCUIT DESCRIPTION PAGE 3......RADIATION INTERFERENCE TEST DATA PAGE 4......38 dB Rejection Ratio EXHIBITS CONTAINING: CONFIDENTIALITY REQUEST LETTER STATEMENT PER 15.121(a) BLOCK DIAGRAMS SCHEMATICS INSTRUCTION MANUAL SAMPLE OF FCC ID LABEL AND SKETCH OF LOCATION RADIATED TEST SETUP PHOTOGRAPH EXTERNAL PHOTOS INTERNAL PHOTOS CIRCUIT DESCRIPTION APPLICANT: VERTEX STANDARD CO., LTD. FCC ID: K6620233X40 REPORT #: V\VERTEX\2091UT5\2091UT5TestReport.doc TABLE OF CONTENTS

APPLICANT: VERTEX STANDARD CO., LTD. FCC ID: K6620233X40 TEST EQUIPMENT LIST Device Manufacturer Model Serial Cal/Char Due Date Number Date 3/10-Meter TEI N/A N/A Listed 3/26/07 OATS 3/27/04 3-Meter TEI N/A N/A Listed 1/12/06 OATS 1/13/03 Biconnical Eaton 94455-1 1057 CAL 3/18/03 3/18/05 Antenna Biconnical Eaton 94455-1 1096 CAL 8/17/04 8/17/06 Antenna Biconnical Electro- BIA-25 1171 CAL 4/29/05 4/29/07 Antenna Metrics Blue Tower HP 85650A 2811A01279 CAL 4/13/05 4/13/07 Quasi-Peak Adapter Blue Tower HP 85685A 2926A00983 CAL 8/3/05 8/3/07 RF Preselector Blue Tower HP 8568B 2928A04729 CAL 4/13/05 4/13/07 Spectrum 2848A18049 Analyzer LISN Electro- ANS-25/2 2604 CAL 8/27/04 8/27/06 Metrics LISN Electro- EM-7820 2682 CAL 4/28/05 4/28/07 Metrics Log- Eaton 96005 1243 CAL 5/8/03 5/8/05 Periodic Antenna APPLICANT: VERTEX STANDARD CO., LTD. FCC ID: K6620233X40 REPORT #: V\VERTEX\2091UT5\2091UT5TestReport.doc Page 1 of 4

TEST PROCEDURE GENERAL: This report shall NOT be reproduced except in full without the written approval of TIMCO ENGINEERING, INC. RADIATION INTERFERENCE: The test procedure used was ANSI STANDARD C63.4-2003 using a HEWLETT PACKARD spectrum analyzer with a preselector. The bandwidth of the spectrum analyzer was 100 kHz with an appropriate sweep speed. The analyzer was calibrated in dB above a microvolt at the output of the antenna. The resolution bandwidth was 100KHz and the video bandwidth was 300KHz. The ambient temperature of the UUT was 80oC with a humidity of 76%. FORMULA OF CONVERSION FACTORS: The Field Strength at 3m was established by adding the meter reading of the spectrum analyzer (which is set to read in units of dBuV) to the antenna correction factor supplied by the antenna manufacturer. The antenna correction factors are stated in terms of dB. The gain of the Preselector was accounted for in the Spectrum Analyzer Meter Reading. Example: Freq (MHz) METER READING + ACF = FS 33 20 dBuV + 10.36 dB = 30.36 dBuV/m @ 3m ANSI STANDARD C63.4-2003 10.1.7 MEASUREMENT PROCEDURES: The unit under test was placed on a table 80 cm high and with dimensions of 1m by 1.5m. The table used for radiated measurements is capable of continuous rotation. When an emission was found, the table was rotated to produce the maximum signal strength. At this point, the antenna was raised and lowered from 1m to 4m. The antenna was placed in both the horizontal and vertical planes. APPLICANT: VERTEX STANDARD CO., LTD. FCC ID: K6620233X40 REPORT #: V\VERTEX\2091UT5\2091UT5TestReport.doc Page 2 of 4

APPLICANT: VERTEX STANDARD CO., LTD. FCC ID: K6620233X40 NAME OF TEST: RADIATION INTERFERENCE RULES PART NUMBER: 15.109 REQUIREMENTS: 30 to 80 MHz: 40.0 dBuV/M @ 3 METERS 88 to 216 MHz: 43.5 dBuV/M 216 to 960 MHz: 46.0 dBuV/M ABOVE 960 MHz: 54.0 dBuV/M TEST RESULTS: A search was made of the spectrum from 30 to 1000 MHz and the measurements indicate that the unit DOES meet the FCC requirements. TEST DATA: Tuned Emission Meter Ant. Coax Correction Field Margin Frequency Frequency Reading Pol Loss Factor Strength dB MHz MHz dBuV dB dB dBuV/m 136.0 114.30 10.9 V 0.66 14.95 26.51 16.99 136.0 114.30 11.0 H 0.66 14.84 26.50 17.00 136.0 342.90 11.7 H 1.14 15.13 27.97 18.03 136.0 457.20 10.7 H 1.26 17.32 29.28 16.72 136.0 571.50 10.4 H 1.51 19.32 31.23 14.77 155.0 133.30 10.8 H 0.68 13.10 24.58 18.92 155.0 133.30 10.9 V 0.68 13.14 24.72 18.78 155.0 399.90 12.0 H 1.20 16.10 29.30 16.70 155.0 399.90 12.2 V 1.20 16.00 29.40 16.60 155.0 666.50 10.5 H 1.67 20.73 32.90 13.10 174.0 152.30 10.1 V 0.71 14.34 25.15 18.35 174.0 152.30 10.3 H 0.71 14.17 25.18 18.32 174.0 456.90 10.5 V 1.26 16.87 28.63 17.37 174.0 456.90 11.9 H 1.26 17.31 30.47 15.53 174.0 609.20 10.4 V 1.61 18.60 30.61 15.39 174.0 761.50 11.2 V 1.82 20.39 33.41 12.59 SAMPLE CALCULATION: FSdBuV/m = MR (dBuV) + ACFdB. TEST PROCEDURE: ANSI STANDARD C63.4-2003 using a Hewlett Packard Model 8566B spectrum analyzer, a Hewlett Packard Model 85685A Preselector, a Hewlett Packard Model 85650A Quasi-Peak adapter, an Electro-Metric Dipole Kit, and an Eaton Model 94455-1 Biconical Antenna. The bandwidth of spectrum analyzer was 100 kHz with an appropriate sweep speed. When an emission was found, the table was rotated to produce the maximum signal strength. The antenna was placed in both the horizontal and vertical planes and the worse case emissions were reported. The receiver was put into the coherent mode by placing an antenna driven by a signal generator off site. The UUT was tested in 3 orthogonal planes. PERFORMED BY: JOSEPH SCOGLIO DATE: OCTOBER 26, 2005 APPLICANT: VERTEX STANDARD CO., LTD. FCC ID: K6620233X40 REPORT #: V\VERTEX\2091UT5\2091UT5TestReport.doc Page 3 of 4

APPLICANT: VERTEX STANDARD CO., LTD. FCC ID: K6620233X40 NAME OF TEST: 38dB REJECTION RATIO RULES PART NUMBER: 15.121(b) REQUIREMENTS: 38dB REJECTION RATIO TO SENSITIVITY OF THE RECEIVER. TEST SET-UP TEST PROCEDURE: The reference sensitivity was measured in accordance with TIA/EIA-603; a. Equipment connected as illustrated b. A standard signal was applied to the receiver input terminals. c. Receiver output audio output was adjusted for rated output. d. The RF Signal generator was adjusted to the lowest level to produce a 12dB SINAD without the audio output dropping more than 3dB. Make note of sensitivity level. e. This was done across the different bands to establish a reference level. The reference taken was the worse case sensitivity. f. The output of the signal generator was then adjusted to a level of 60dB above the reference level at a frequency of 824.5MHz. g. With the level set 60dB above the level measured in step e. h. Set squelch on receiver to threshold, the signal level required to open the squelch must be lower than the level measured in step d. i. Cause the receiver to scan or step-it through its complete range of frequencies. j. If receiver stops or unsquelches on any frequency, record the frequency and then adjust the level until a 12dB SINAD is produced. This level must be greater than 38dB above the level in step e. k. Repeat steps f through j for frequencies 836.0, 848.5, 869.1, 881.0, & 893.5MHz. TEST RESULTS: The UUT meets the 38dB REJECTION RATIO. PERFORMED BY: NAM NGUYEN DATE: 10/26/05 APPLICANT: VERTEX STANDARD CO., LTD. FCC ID: K6620233X40 REPORT #: V\VERTEX\2091UT5\2091UT5TestReport.doc Page 4 of 4


Document Created: 2005-11-09 15:51:05
Document Modified: 2005-11-09 15:51:05
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC