Users Manual

FCC ID: K6610443250

Users Manual

Download: PDF
FCCID_556895

FCC ID: K6610443250/IC ID: 511B-10443250 RACK MOUNT REPEATER VXR-9000-H OPERATING MANUAL VERTEX STANDARD CO., LTD. 4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan VERTEX STANDARD US Headquarters 10900 Walker Street, Cypress, CA 90630, U.S.A. YAESU EUROPE B.V. P.O. Box 75525, 1118 ZN Schiphol, The Netherlands YAESU UK LTD. Unit 12, Sun Valley Business Park, Winnall Close Winchester, Hampshire, SO23 0LB, U.K. VERTEX STANDARD HK LTD. Unit 5, 20/F., Seaview Centre, 139-141 Hoi Bun Road, Kwun Tong, Kowloon, Hong Kong VXR-9000 FM REPEATER OPERATING MANUAL Vertex Standard Co., Ltd.

FCC ID: K6610443250/IC ID: 511B-10443250 VXR-9000 FM REPEATER OPERATING MANUAL Vertex Standard Co., Ltd.

FCC ID: K6610443250/IC ID: 511B-10443250 INTRODUCTION The VXR-9000 is commercial-grade 50-watt FM repeater designed to provide reliable two-way full-duplex commu- nications over a wide range of environmental conditions. Designed to mount in a standard 19-inch rack, the VXR-9000 is crafted using the latest computer-aided design and manufacturing processes, to ensure a high level of reliability to users. Important channel frequency data is stored in EEPROM, and is easily programmable by a Servicing Technician or Dealer using an IBM compatible personal com- puter and the VPL-1 Programming Cable and CE60 Software. Please take a few minutes to read this manual carefully. The information presented here will allow you to derive maximum performance from your VXR-9000. After reading it, keep this manual handy for quick reference, in case questions arise later on. Important Note: Internal service work, programming, and accessory installations should only be performed by your authorized Vertex Standard Dealer. Dangerous conditions and/or possibly illegal operation may result from im- proper setup, programming, or internal modifications. SAFETY/WARNING INFORMATION The antenna(s) used for this transmitter must be fixed-mounted on outdoor permanent structures with a separation distance of at least 1.98m 74cm from all persons during normal operation and must not exceed an antenna gain of 0 dBd. This device must be restricted to work related operations in an Occupational/Con- trolled RF exposure Environment, not exceeding a maximum transmitting duty factor of 50%. The antenna(s) used with this device must satisfy the antenna co-location requirements of 47 C.F.R. 1.1307(b)(3). NOTICE!  Do not modify this repeater for any reason. Refer service of this repeater to qualified technicians only.  When the repeater become abnormal, such as the overheating, smoke smell of burning, etc., turn the main power switch off and disconnect the Main Power Source connector from the rear of the VXR-9000 imme- diately. Also disconnect any backup power source you may have connected to the rear of the VXR-9000.  Do not place any combustible material near the repeater.  Do not spray any liquid over the repeater.  Ensure that the power and antenna connections are securely made, using cables with excess capacity for the power being utilized. VXR-9000 FM REPEATER OPERATING MANUAL 1 Vertex Standard Co., Ltd.

FCC ID: K6610443250/IC ID: 511B-10443250 FRONT PANEL CONTROLS & CONNECTORS  POWER (O/I) Switch  TX Indicator This is the main power switch for the repeater. This LED glows red when the repeater is transmit- ting.  Power Indicator (MAIN) This LED glows green when the main power source  Numeric Display is used. This display consists of two 7-segment LEDs, indi- cating the channel number during normal opera-  Power Indicator (BACKUP) tion. If an abnormal condition arises, an error code This LED glows red when the backup power source will be displayed: is used. DISPLAY DESCRIPTION 01 - 32 Channel Number  MIC Jack PC Clone Active Connect the microphone plug to this jack. This jack UL PLL Unlock is also used for writing and reading channel fre- HI High temperature in PA Unit quency or other configurations via the COM Port of SC Scan Active the PC on which the clone editor (CE60) is running. LC Front Panel Keys are Locked E1 PTT key is Disabled  Programmable Function (PF) Key E2 Cooling Fan is Disabled Six pushbuttons on the front panel are program- E5 Low Voltage in Backup Battery mable function (PF) keys, each with an orange in- E7 PA Unit Abnormality dicator inside. Each key can be programmed with E3, E4, E6, E9 Contact your Dealer two functions, one for a “long” press and one for a “momentary” press. The PF key functions may be BUSY Indicator customized, via programming by your VERTEX This LED glows green when the receiving channel STANDARD dealer, to meet your communications is busy. network requirements. Note that some functions may require the purchase of optional internal ac- Speaker cessories. The possible PF key features and func- The internal speaker is located here. tions are explained on the pages to follow.  VOL Knob This control knob adjusts the output level of the front speaker and external speaker jack on the back panel. 2 VXR-9000 FM REPEATER OPERATING MANUAL Vertex Standard Co., Ltd.

FCC ID: K6610443250/IC ID: 511B-10443250 PROGRAMMABLE FUNCTION (PF) KEY DETAILS PF-1 KEY PF-2 KEY PF-3 KEY PF-4 KEY PF-5 KEY PF-6 KEY FUNCTION PRESS PRESS & HOLD PRESS PRESS & HOLD PRESS PRESS & HOLD PRESS PRESS & HOLD PRESS PRESS & HOLD PRESS PRESS & HOLD CH DOWN CH UP COMPANDER CTCSS/DCS ENC CTCSS/DCS DEC CW ID TWO TONE DEC CW ID SIGNAL CW MESSAGE 1 CW MESSAGE 2 CW MESSAGE 3 CW MESSAGE 4 CW MESSAGE 5 CW MESSAGE 6 CW MESSAGE 7 CW MESSAGE 8 DC POWER SAVE ENCRYPTION ENCRYPTION CODE KEY LOCK LOCAL PTT MONITOR MONITOR M MULTI TONE PANEL INDICATOR REMOTE REPEAT RESET SCAN SQUELCH TEST TONE TEST TONE M TOT TRANSMIT TX POWER MID TX POWER LOW CH DOWN CTCSS/DCS ENC Press (or Press and hold in for one second) the PF key Press (or Press and hold in for one second) the PF key assigned to “CH Down” to step to the next-lower oper- assigned to “CTCSS/DCS Enc” to turn the CTCSS/DCS ating channel. Encoder “On” or “Off” (toggle). CH UP CTCSS/DCS DEC Press (or Press and hold in for one second) the PF key Press (or Press and hold in for one second) the PF key assigned to “CH Up” to step to the next-higher operat- assigned to “CTCSS/DCS Dec” to turn the CTCSS/DCS ing channel. Decoder “On” or “Off” (toggle). COMPANDER CW ID Press (or Press and hold in for one second) the PF key Press (or Press and hold in for one second) the PF key assigned to “Compander” to turn the Compander cir- assigned to “CW ID” to turn the CW Identifier feature cuit “On” or “Off” (toggle). This function is only acti- “On” or “Off” (toggle). vated on the “Narrow Channel Spread” of the “Base When the CW ID feature is set to “On,” your station’s Transceiver” mode. callsign will be superimposed on the outbound signal, The Compander IC contains two variable gain circuits in Morse Code, at the beginning of every transmission. configured for compressing and expanding the dynamic Programming of the callsign is performed by your VER- range of the repeater’s transmitted and received audio TEX STANDARD dealer. signal. When you enable this function, the signal-to- noise ratio can be improved by reducing the transmit- ted audio dynamic range. VXR-9000 FM REPEATER OPERATING MANUAL 3 Vertex Standard Co., Ltd.

FCC ID: K6610443250/IC ID: 511B-10443250 PROGRAMMABLE FUNCTION (PF) KEY DETAILS TWO TONE DEC MONITOR Press (or Press and hold in for one second) the PF key Press (or Press and hold in for one second) the PF key assigned to “Two Tone Dec” to turn the 2-Tone Decoder assigned to “Monitor” to cancel CTCSS and DCS squelch “On” or “Off” (toggle). decoding, so as to enable reception of signals present on the channel that do not contain a matching CTCSS tone CW ID SINGLE or DCS code. Press (or Press and hold in for one second) the PF key assigned to “CW ID Single” to send the station callsign, MONITOR M via Morse Code, once. Programming of the callsign is This function provides to “Monitor” to cancel CTCSS performed by your VERTEX STANDARD dealer. and DCS squelch decoding, so long as the PF key as- signed to “Monitor M” is pressed and held in. CW MESSAGE 1 - CW MESSAGE 8 Press (or press and hold in for one second) the PF key MULTI TONE assigned to “CW Message 1 - 8” to send a pre-pro- Press (or Press and hold in for one second) the PF key grammed Morse Code message on the transmitted sig- assigned to “Multi Tone” to switch the Tone Table be- nal. Programming of the message(s) is performed by tween “Main” and “Sub.” your VERTEX STANDARD dealer. PANEL INDICATOR DC POWER SAVE Press (or Press and hold in for one second) the PF key Press (or Press and hold in for one second) the PF key assigned to “Panel Indicator” to turn the Front Panel’s assigned to “DC Power Save” to turn the DC Power Illumination “On” or “Off” (toggle). Save feature “On” or “Off” (toggle). When DC Power Save feature is set to “ON,” activate REMOTE Press (or Press and hold in for one second) the PF key the various power save feature (determined from your assigned to “Remote” to toggle the operating mode be- VERTEX STANDARD dealer) while the repeater oper- tween the “Remote” mode and “Local” mode. ates from the Backup Power Source. When the “Remote” mode is selected, the repeater op- ENCRYPTION erates according to the control instructions received Press (or Press and hold in for one second) the PF key from the external device (connected to the ACC jack on assigned to “Encryption” to turn off the Optional En- the rear panel). While in the “Local” mode, the repeater cryption Unit temporarily. operates from the front panel’s PF keys. ENCRYPTION CODE REPEAT Press (or Press and hold in for one second) the PF key Press (or Press and hold in for one second) the PF key assigned to “Encryption Code” to select the Encryption assigned to “Repeat” to toggle the operating mode be- Code (determined from your VERTEX STANDARD tween the “Repeater” mode and “Base Transceiver” dealer; require the FVP-35 Rolling Code Encryption mode. Unit). For normal operation, set this key to the “Repeat” mode. When the “Base Transceiver” mode is selected, you can KEY LOCK speak into the microphone to use this repeater as a trans- Press (or Press and hold in for one second) the PF key ceiver. assigned to “Key Lock” to lock the repeater’s front panel keys (except “Key Lock” key); this feature can be en- RESET abled to prevent repeater settings from being disturbed. Press (or Press and hold in for one second) the PF key assigned to “Reset” to reset (same function as the LOCAL PTT POWER switch “off” and “on”) the repeater. Press (or Press and hold in for one second) the PF key assigned to “Local PTT” to enable (“On”) or disable (“Off”) operation using a PTT switch connected to the front panel’s Microphone Jack. 4 VXR-9000 FM REPEATER OPERATING MANUAL Vertex Standard Co., Ltd.

FCC ID: K6610443250/IC ID: 511B-10443250 PROGRAMMABLE FUNCTION (PF) KEY DETAILS SCAN TOT Press (or Press and hold in for one second) the PF key Press (or press and hold in one second) the PF key as- assigned to “Scan” to start scanning. To stop scanning, signed to “TOT” to turn the Time-Out Timer feature press (or Press and hold in for one second) this key again. “On” or “Off” (toggle). The scanning feature is used to monitor multiple chan- When the TOT feature is set to “On,” the repeater will nels programmed into the repeater. return to the “Receive” mode automatically after a pre- set time of continuous transmission (determined via This function is only activated on the “Base Trans- programming by your VERTEX STANDARD dealer). ceiver” mode. SQUELCH TRANSMIT Press (or Press and hold in for one second) the PF key Press (or Press and hold in for one second) the PF key assigned to “Transmit” to enable (“On”) or disable assigned to “Squelch” to override the Squelch action (“Off”) the transmission of the VXR-9000. (CTCSS, DCS, and Noise Squelch), so as to hear any sig- nal present on the operating channel. TX POWER MID Press (or Press and hold in one second) the PF key as- TEST TONE signed to “TX Power Mid”to set the transmitter power Press (or Press and hold in for one second) the PF key to the “Mid” level. assigned to “Test Tone” to generate the Test Tone Signal, as programmed by your VERTEX STANDARD dealer. Press (or press and hold in one second) this key again to return to the “Original” power level (determined via Press (or Press and hold in for one second) this key again programming by your VERTEX STANDARD dealer). to stop the generation of the Test Tone. This is a toggle function. This function is ignored on the channel which is pro- grammed to the transmitter power to the “Mid” or Press (or Press and hold in for one second) this key while “Low” level by your VERTEX STANDARD dealer. press and holding the PTT switch to transmit the Test Tone Signal, as programmed by your VERTEX STAN- DARD dealer. TX POWER LOW Press (or Press and hold in one second) the PF key as- signed to “TX Power Low”to set the transmitter power TEST TONE M to the “Low” level. This function provides momentary generation of the above-referenced Test Tone signal, so long as the PF key Press (or press and hold in one second) this key again to assigned to “Test Tone M” is pressed and held in. return to “Original” power level (determined via pro- gramming by your VERTEX STANDARD dealer). Press this key while press and holding the PTT switch to transmit the Test Tone Signal, as programmed by This function is ignored on the channel which is pro- your VERTEX STANDARD dealer. grammed to the transmitter power to the “Low” level by your VERTEX STANDARD dealer. VXR-9000 FM REPEATER OPERATING MANUAL 5 Vertex Standard Co., Ltd.

FCC ID: K6610443250/IC ID: 511B-10443250 REAR PANEL CONNECTORS TX BACKUP BACKUP MAIN RX INPUT DC 13.6V GND EXT ACC  Backup Power Source Terminals  Main Power Source Connector If available, a backup 13.6 Volt power source, such The primary DC power source should be connected as a rechargeable battery, may be connected here. here. The power requirements are 13.6 V DC at 12 When the Battery Charge switch (located on the PA Amps, continuous duty. Unit) is set to “ON,” a “trickle” charge current is present here while the repeater is operating from  External Speaker Jack the “Main Power Source.” This 3.5-mm, 2-pin jack provides variable audio output for an external speaker. The audio output  Circuit Protection Fuse impedance at this jack is 4 to 16 Ohms, and the level Two 15-Amp blade fuses, for the “Main” and varies according to the setting of the front panel's “Backup” power sources, are installed here. VOL knob.  RX Antenna Jack  DSUB 25-pin Accessory Connector This BNC-type coaxial jack accepts the receiver in- This DB-25F connector allows the repeater to be re- put signal, for connection to the receiving antenna, mote-controlled by an external controller. Analog or the “RX” jack on the duplexer. The input imped- I/O signals, such as TX Audio In, Discriminator ance requirement is 50 Ohms. Output, RSSI, etc. are available. Moreover, the VXR- 9000 provides eight ports that can be programmed  TX Antenna Jack for various input or output signals, or for control This N-type coaxial jack provides the transmitter functions. Each port may be programmed as to its output signal, for connection to the transmitting function, its status (input or output), and its logic antenna, or the “TX” jack on the duplexer. The out- (for output ports only). put impedance requirement is 50 Ohms. 6 VXR-9000 FM REPEATER OPERATING MANUAL Vertex Standard Co., Ltd.

FCC ID: K6610443250/IC ID: 511B-10443250 DB-25 CONNECTOR PORT The VXR-9000 repeater is provided with a 25-pin DB- Pin 5: TX ATT 25F female connector for interconnections to This output is intended for controlling an external co- accessories.Use a DB-25M 25-pin male connector to con- axial switching relay. It is an open drain output which nect accessories to the repeater. The pins on the acces- can sink approx. 1.5 A when active. The delay time sory connector are explained in detail as follows: which is between the repeater cause to transmit mode and this port switches to ground can be programmed Pin 1: GND by your VERTEX STANDARD dealer. Chassis ground for all logic levels and power supply return. Pin 6: DISC OUT [ANALOG OUTPUT] (WIDE-BAND: 0 ~ 3,000 HZ) Pin 2: +13.6 V Received signals with full system deviation produce [POWER SUPPLY] 350 mVrms audio at this pin. The output impedance is This pin provides 13.6 Volts, 2.0 A, DC from the repeater 600 Ohm, and is extracted before the de-emphasis and supply. There is a internal 3 A fuse to prevent damage squelch circuitry. Use shielded cable to connect to this to the repeater. pin, and connect the shield to GND. Pin 3: TX AF IN Pin 7: N.C. [ANALOG TRANSMITTER INPUT] (VOICE BAND: 300 ~ 3,000 HZ) No connection. This pin is audio input. Input impedance is 600 Ohms. This audio is injected before the splatter filter stage, so Pin 8: RSSI excess signal input levels are clipped. [ANALOG OUTPUT] Use shielded cable to connect to this pin, and connect A DC voltage proportional to the strength of the signal the shield to GND. currently being received (Receiver Signal Strength In- dicator) is provided on this pin. This low impedance Pin 4: TONE IN output is generated by the receiver IF sub-system and [TRANSMITTER INPUT] (SUB-AUDIBLE BAND: 5 ~ 250 HZ) buffered by an internal op-amp. Typical voltages are This pin is sub-audiable tone input. The input imped- graphed as follows: ance is 600 Ohms, and has a flat response characteristic (DC V) (repeater deviation is constant for a given signal level RSSI Output Voltage 2.5 over the frequency range of 5 ~ 250 Hz). Injecting too 2.0 high a voltage here causes over-deviation of CTCSS or 1.5 DCS, degrading performance. 1.0 Use shielded cable to connect to this pin, connecting the 0.5 shield to GND. 0 –60 –70 –80 –90 –100 –110 –120 (dBm) Input Signal Level Pin 9: COAX. SW [LOGIC OUTPUT (ACTIVE LOW)] This output is intended for controlling an external co- axial switching relay. It is an open drain output which can sink approx. 1.5 A when active. This signal only switches if the repeater has been programmed for “SIM- PLEX” mode. If programmed for “DUPLEX,” the signal remains open (high impedance) at all time. DB-25 PIN NUMBERING VXR-9000 FM REPEATER OPERATING MANUAL 7 Vertex Standard Co., Ltd.

FCC ID: K6610443250/IC ID: 511B-10443250 DB-25 CONNECTOR PORT Pin 10, 13, 15, 16, 17, 18, 19, 21: Pin 23: RXD HIGH PROGRAMMABLE I/O “0” ~ ”7” Pin I/O Port [DIGITAL OUTPUT FOR DATA COMMUNICATIONS] The VXR-9000 provides eight ports (PIO) 10 6 (Max.: 5 kHz) 13 7 This pin is an output for high speed receiving data sig- that can be programmed for various 15 4 input or output signals, or for control nals (typically 9600 bps), with the data being extracted 16 3 functions. Each port may be pro- 17 2 immediately after the discriminator (prior to any de- grammed as to its function, its status 18 1 emphasis). (input or output), and its logic (for out- 19 0 put ports only). 21 5 Pin 24: TXD LOW [ANALOG INPUT FOR DATA COMMUNICATIONS] Pin 11: NSQ DET (300 ~ 3,000 Hz) This is an open-collector, active-low output capable of This pin is intended to be used as a low speed data sinking about 10 mA. It indicates that the receiver signal input to the repeater (typically 1200 bps). This squelch is open. If the squelch control is properly set, digital data signal is injected before the transmitter pre- this indicates a carrier on the receiver channel. emphasis and limiting stages, so excess signal input levels are clipped. Pin 12: EXT PTT This input is internally pulled up to 5 VDC. When pulled Pin 25: TXD HIGH low by an external device, it keys the repeater trans- [DIGITAL INPUT FOR THE DATA COMMUNICATIONS] mitter while the repeater is operating in the “Remote” (0 ~ 5 kHz) mode. Avoid voltage in excess of 5 V on this pin, or This pin is intended to be used as a high speed digital internal damage to the microprocessor on the repeater data signal input to the repeater (typically 9600 bps). CNTL Unit may result. This digital data signal is injected after the transmitter splatter filter stage. Pin 14, 20: GND Chassis ground for all logic levels and power supply return. Pin 22: RXD LOW [ANALOG OUTPUT FOR DATA COMMUNICATIONS] (300 ~ 3,000 Hz) This pin is an output for low speed receiving data sig- nals (typically 1200 bps), with the data being extracted after the de-emphasis and low pass filter stages. 8 VXR-9000 FM REPEATER OPERATING MANUAL Vertex Standard Co., Ltd.

FCC ID: K6610443250/IC ID: 511B-10443250 INSTALLATION Antenna Considerations Equipment Location Repeater operation requires two antennas, one for re- The VXR-9000 must be installed in a 19-inch Mounting ceiving and one for transmitting, so that the receiving Rack, which will allow for free air flow around the heat antenna does not absorb energy from the transmitting sink on the rear apron at all times. In warm climates, antenna. There are a number of ways to do this, de- the repeater should not be sealed in a small, closed room pending on the TX/RX frequency separation, and on the without air conditioning. locations available for antenna mounting. While the operating temperature range of the VXR-9000 Regardless of the above choice, it is of paramount im- is quite broad, the best location is one in which the air portance that the antenna(s) be mounted as high and in temperature does not approach the extremes of the the clear as possible, preferably within line-of-sight to specified range, and one that does not change rapidly. all repeater users. Furthermore, losses in the feedline(s) Protect the VXR-9000 (Mounting Rack) from wind and must be minimized, so the feedline(s) should be high rain, and extremes in temperature or humidity that quality, and as short as possible. If a long feedline is may shorten the useful life of the equipment. Try to lo- necessary, use coaxial “hardline” cable to reduce losses. cate the VXR-9000 (Mounting Rack) in an environment Repeater antennas should have an impedance of 50 Ω that is also comfortable for service personnel, if pos- at the operating frequency. When separate receive and sible. transmit antennas are used, high-Q narrow-band types may serve to minimize interaction. NEVER TRANSMIT WITHOUT HAVING A TRANSMIT ANTENNA CONNECTED TO THE TX ANTENNA JACK OF THE REPEATER. VXR-9000 FM REPEATER OPERATING MANUAL 9 Vertex Standard Co., Ltd.

FCC ID: K6610443250/IC ID: 511B-10443250 INSTALLATION Power Supply Backup Power Supply Operation of the VXR-9000 requires a power source ca- For uninterrupted operation during power failures, a pable of providing at least 12 Amps continuously at 12-volt rechargeable type battery (55-Ah or more rec- 13.6 Volts DC. The FP-1023 (23 A) and FP-1030A (30 A) ommended) may be connected to the BACKUP termi- AC Power Supplies are available from your Vertex Stan- nal posts on the rear panel. While the repeater is oper- dard dealer to satisfy these requirements. Other well- ating from the Main Power Source a slight charging regulated power supplies may be used, as well, if they current will maintain battery charge. In the event of an meet the above voltage and current specifications. unexpected interruption of the Main Power Source, the automatic power control circuit will automatically Use the DC power cable supplied with your repeater switch the repeater to the backup battery, and opera- for making power connections to the power supply. tion will not be interrupted. Connect the RED power cable lead to the POSITIVE (+) power supply terminal, and connect the BLACK power After prolonged operation from the battery, (Backup cable lead to the NEGATIVE (–) power supply terminal. Power Source), it should be disconnected from the re- peater and recharged separately before re-connecting, as the trickle charge is not sufficient for recharging a completely discharged battery. Never reapply the Main Power Source to the repeater with a discharged battery connected as backup, as the DC startup current can damage the repeater and bat- tery. While operating from a backup battery, the repeater requires approximately 7 amperes at 12 Volts during transmit. Never short the “Backup Power Sorce” Terminals, when the Battery Charge switch (located on the PA  To RX Antenna  To TX Antenna Unit) is set to “ON.” BACKUP B ACK UP MAIN RX TX INPUT DC 13.6V GND EXT ACC BLACK BLACK RED RED Supplied DC Power Code Backup Battery (12 V, 55 Ah) TYPICALLY SETUP 10 VXR-9000 FM REPEATER OPERATING MANUAL Vertex Standard Co., Ltd.

FCC ID: K6610443250/IC ID: 511B-10443250 ACCESSORIS & OPTION Supplied Accessories Optional Accessories DC Power Cord (T9023499) ............................................ 1 FIF-9 Inline Interface Box 15-A Blade Fuse (Q0000075) ........................................... 1 FVP-25 Encryption Unit Knob Cap (RA0506900) ................................................... 6 FVP-35 Rolling Code Encryption Unit Name Plate (RA0508500) ................................................ 1 MD-11A8J Desktop Microphone Operating Manual ........................................................... 1 MH-25A8J Hand Microphone VXR-9000 FM REPEATER OPERATING MANUAL 11 Vertex Standard Co., Ltd.

FCC ID: K6610443250/IC ID: 511B-10443250 SPECIFICATIONS General Frequency Range: Type C : 148 - 174 MHz Number of channel: 32 PLL Step: 2.5 kHz/5 kHz/6.25 kHz Operating Voltage: 13.6V DC ±10 % Current Drain: 30A Maximum Frequency Stability: 1.5 ppm 1.0 ppm (30min after wake up) Operating Temperature Range: –22 °F to +140 °F (–30 °C to +60 °C) Dimensions (W x H x D): 19 x 3-1/2 x 13-1/2 inch (483 x 88 x 343 mm) Weight (Approx.): 20 kg Receiver Antenna Impedance: 50 ohm Antenna Connector: Type-BNC Receiver Type: Double-Conversion Superheterodyne Sensitivity: 0.25 µV (12dB SINAD) Selectivity: 85 dB (Wide), 75 dB (Narrow) Intermodulation: 82 dB (Wide), 78 dB (Narrow) Image Rejection: 90 dB Squelch Threshold: –5 dBµ Audio Output: 4 W @4 ohm Audio Distortion: <3% Hum and Noise: > 55 dB (Wide), > 50 dB (Narrow) Audio Frequency Response: De-emphasis : 6 dB/oct (From 300 Hz to 3 kHz) Conducted Spurious: < –80 dBm Transmitter RF Output Power: 100/75/50 W (High/Mid/Low) Antenna Impedance: 50 ohm Antenna Connector: Type-N Modulation Type: 16K0F3E/11K0F3E System Deviation: ±5.0 kHz (Wide), ±2.5 kHz (Narrow) Hum and Noise: > 50 dB (Wide), > 45 dB (Narrow) Microphone Sensitivity: 5 mV Audio Frequency Response: Pre-emphasis : 6dB/oct (From 300 Hz to 3 kHz) Spurious Emission: 70dB below carrier Audio Distortion: 3.0 % @1 kHz Microphone Impedance: 600 ohm Specifications subject to change without notice or obligation. 12 VXR-9000 FM REPEATER OPERATING MANUAL Vertex Standard Co., Ltd.

FCC ID: K6610443250/IC ID: 511B-10443250 Part 15.21: Changes or modifications to this device not expressly ap- proved by Vertex Standard could void the user’s authorization to operate this device. VXR-9000 FM REPEATER OPERATING MANUAL Vertex Standard Co., Ltd.

FCC ID: K6610443250/IC ID: 511B-10443250 Copyright 2005 No portion of this manual may be VERTEX STANDARD CO., LTD. reproduced without the permission of All rights reserved. VERTEX STANDARD CO., LTD. 0504s-BE Printed in Japan Vertex Standard Co., Ltd.


Document Created: 2005-06-01 21:06:07
Document Modified: 2005-06-01 21:06:07
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC