Test Report

FCC ID: K6610342150

Test Report

Download: PDF
FCCID_1061984

Page 1 of 34 REPORT ON Radio testing of the VERTEX STANDARD VX‐5500L In accordance with ANSI/TIA/EIA‐603, RSS‐119 Report number TA000657 December 2008 Vertex Standard Co., Ltd.

Report number TA000657 Page 2 of 34 GENERAL INFORMATION MODEL NAME: VX‐5500L FCC ID: K6610342150 MANUFACTURER: Vertex Standard Co., Ltd. TRADE NAME: VERTEX STANDARD EUT DESCRIPTION: VHF FM Transceiver SERIAL NUMBER: 8M000001 VOLTAGE RQUIREMENTS: 13.8 [V] DC NUMBER OF CHANNELS: 250 SPECIFICATION ARE REFERENCED: ANSI/TIA/EIA‐603 RSS‐119 TRANSMITTERS TYPE OF EMISSION: 16K0F3E FREQUENCY RANGE: 29.7 to 37 [MHz] POWER OUTPUT RATING: 30 to 70 [W] Switchable x Variable N/A MAXIMUM POWER RATING: 200 [W] INPUT IMPEDANCE (MIC): 600 [Ω] OUTPUT IMPEDANCE (RF): 50 [Ω] Collector Voltage: 13.8 [V] Collector Current: 12 [A] RＥＣＥＩＶERS FREQUENCY RANGE: 29.7 to 37 [MHz] INTERMEDIATE FREQUENCIES: 1st 17.7 [MHz] 2nd ‐450 [kHz] INPUT IMPEDANCE (RF): 50 [Ω] OUTPUT IMPEDANCE (SP): 4 [Ω] AUDIO OUTPUT POWER: 12 [W] This report was prepared by Vertex Standard Co., Ltd. Test performed by Shige.Takahashi Date 10 / December /2008 Vertex Standard Co., Ltd.

Report number TA000657 Page 3 of 34 VX‐5500L Channel Settings Transmit Receive Shown on Power CH No. Frequency Frequency CH Spacing LCD High Low [MHz] [MHz] 1 29_7_HI 29.700 29.700 20k 70W ‐ 2 33_35_HI 33.350 33.350 20k 70W ‐ 3 37_HI 37.000 37.000 20k 70W ‐ 4 29_7_LO 29.700 29.700 20k ‐ 30W 5 33_35_LO 33.350 33.350 20k ‐ 30W 6 37_LO 37.000 37.000 20k ‐ 30W 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Vertex Standard Co., Ltd.

Report number TA000657 Page 4 of 34 NAME OF TEST: R.F. Power Output (Conducted) SPECIFICATION: 47 CFR 2.1046 (a) GUIDE: ANSI/TIA/EIA‐603, Paragraph 2.2.1 TEST EQUIPMENT: As per attached page MEASUREMENT PROCEDURE 1. The EUT was connected to a resistive coaxial attenuator of normal load impedance, and the modulated output powerwas measured by means of an R.F. power meter. 2. Measurement accuracy is ± 4% MEASUREMENT RESULTS R.F. POWER, WATTS NOMINAL, MHz CHANNEL LOW HIGH 29.700 1 30.700 70.600 33.350 2 30.400 70.200 37.000 3 30.900 66.000 Vertex Standard Co., Ltd.

Report number TA000657 Page 5 of 34 TRANSMITTER POWER CONDUCTED MEASUREMENTS TEST 1: R.F. POWER OUTPUT TEST 2: FREQUENCY STABILITY Test (1) (2) (3) (4) Sample Power (5) Supply Instruments Description Serial Number (1) COAXUAL ATTENUATOR WEINSCHELL 49‐10‐43 *** (2) RF COUPLER ADVANTEST TR4153 *** (3) POWER SENSOR Agilent 8482B *** (4) POWER METER Agilent 8901B POWER MODE *** (5) FREQUENCY COUNTER Agilent 8901B FREQUENCY MODE *** Vertex Standard Co., Ltd.

Report number TA000657 Page 6 of 34 NAME OF TEST: Unwanted Emissions (Conducted) SPECIFICATION: 47 CFR 2.1051 GUIDE: ANSI/TIA/EIA‐603, Paragraph 2.2.13 TEST EQUIPMENT: As per attached page MEASUREMENT PROCEDURE 1. The emissions were measured for the worst case as follows: (a): within a band of frequencies defined by the carrier frequency plus and minus one channel. (b): from the lowest frequency generated in the EUT and to at least the 10th harmonic of the carrier frequency, or 40GHz, whichever is lower. 2. The magnitude of spurious emissions that are attenuated more than 20dB below the permissible value need not be specified. 3. MEASUREMENT RESULTS: FREQUENCY OF CARRIER, MHz = 29.7 , 33.35 , 37 SPECTRUM SEARCHED, GHz = 0 to 10 x Fc MAXIMUM RESPONSE, Hz = 2700 ALL OTHER EMISSIONS = >= 20dB BELOW LIMIT Vertex Standard Co., Ltd.

Report number TA000657 Page 7 of 34 TRANSMITTER SPURIOUS EMISSION TEST 1: OCCUPIED BANDWIDTH (IN‐BAND SPURIOUS) TEST 2: OUT‐OF‐BAND SPURIOUS Test (1) (2) (3) Sample Power Supply Instruments Description Serial Number (1) AUDIO GENERATOR Agilent 8903B *** (2) COAXUAL ATTENUATOR WEINSCHELL 49‐10‐43 *** (2) COAXUAL ATTENUATOR Agilent 8498A *** (3) SPECTRUM ANALYZER ADVANTEST TR4173 *** Vertex Standard Co., Ltd.

Report number TA000657 Page 8 of 34 NAME OF TEST: Unwanted Emissions (Conducted) LIMITʹS), dBc: ‐(43+10xLOG(P)) = ‐61 ( 70 Watts ) ‐(43+10xLOG(P)) = ‐58 ( 30 Watts ) High Power FREQUENCY FREQUENCY LEVEL, LEVEL, MARGIN, TUNED, MHz EMISSION, MHz dBm dBc dB 33.3500 66.7000 ‐33.0 ‐81.5 20.0 Vertex Standard Co., Ltd.

Report number TA000657 Page 9 of 34 NAME OF TEST: Unwanted Emissions (Conducted) LIMITʹS), dBc: ‐(43+10xLOG(P)) = ‐61 ( 70 Watts ) ‐(43+10xLOG(P)) = ‐58 ( 30 Watts ) Low Power FREQUENCY FREQUENCY LEVEL, LEVEL, MARGIN, TUNED, MHz EMISSION, MHz dBm dBc dB measurements exceed the requirements by more than 20 dB Vertex Standard Co., Ltd.

Report number TA000657 Page 10 of 34 NAME OF TEST: Field Strength of Spurious Radiation SPECIFICATION: 47 CFR 2.1053 (a) GUIDE: ANSI/TIA/EIA‐603, Paragraph 1.2.12 MEASUREMENT PROCEDURE 1.2.12.1 Definition: Radiated spurious emissions are emissions from the equipment when transmitting load on a frequency or frequencies which are outside an occupied band sufficient to ensure transmission of information of required quality for the class of communications desired. 1.2.12.2 Method of measurement A) Connect the equipment as illustrated. B) Adjust the spectrum analyzer for the following settings: 1) Resolution Bandwidth <= 3kHz 2) Video Bandwidth >= 10kHz 3) Sweep Speed <= 2000Hz/second 4) Detector Mode = Positive Peak C) Place the transmitter to be tested on the turntable in the standard test site. The transmitter is transmitting into a non‐radiating load which is placed on the turntable. The RF cable to this load should be of minimum length. Test antenna STANDARD TRANSMITTER SPECTRUM TRANSMITTER UNDER TEST ANALYZER LOAD STANDARD TEST SITE D) For each spurious measurment the test antenna should be adjusted to the correct length for the frequency involved. This length maybe determined from a calibration ruler supplied with the equipment. Measurements shall be made from the lowest radio frequency generated in the equipment to the tenth harmonic of the carrier, except for the region close to the carrier qeual to ± the test bandwidth (see section 1.3.4.4). E) For each spurious frequency, raise and lower the test antenna from 1 m to 4 m to obtain a maximum reading on the spectrum analyzer with the test antenna at horizontal polarity. Vertex Standard Co., Ltd.

Report number TA000657 Page 11 of 34 NAME OF TEST: Field Strength of Spurious Radiation F) Repeat step E) for each spurious frequency with the test antenna polarized vertically Substitution Test antenna antenna RF SIGNAL SPECTRUM GENERATOR ANALYZER STANDARD TEST SITE G) Reconnect the equipment as illustrated. H) Keep the spectrum analyzer adjusted as in step B). I) Remove the transmitter and replace it with a substitution antenna (the antenna should be half‐wavelength for each frequency involved). The center of the substitutuion antenna should be approximately at the same location as the center of the transmitter. At lower frequencies, where the substitution antenna is very long, this will be impossible to achieve when the antenna is plarized vertically. In such case the lower end of the antenna should be 0.3m above the ground. J) Feed the substitution antenna at the transmitter end with a signal generator connected to the antenna by means of a non‐radiating cable. With the antennas at both ends horizontally polarized and with the signal generator tuned to a particular spurious frequency, raise and lower the test antenna to obtain a maximum reading at the spectrum analyzer. Adjust the level of the signal generator output untill the previusl recorded maximum reading for the set of conditions is obtained. This should be done carefully repeating the adjustment of the test antenna and generator output. K) Repeat step J) with both antennas vertically polarized for each spurious frequency. L) Calculate power in dBm into a reference ideal half‐wave dipole antenna by reducing the readings obtained in step J) and K) by the power loss in the cable between the generator and the antenna and futher corrected for the gain of the substitution antenna used relative to an ideal half‐wave dipole antenna. M) The levels recorded in step L) are absolute levels of radiated spurious emissions in dBm. The radiated spurious emissions in dB can be calculated by the following: Radiated spurious emissions dB = 10log(TX power in watts/0.001) ‐ the levels in step L) Vertex Standard Co., Ltd.

Report number TA000657 Page 12 of 34 NAME OF TEST: Field Strength of Spurious Radiation Note: It is permissible that other antennas provided can be referenced to a dipole. Instruments Description Serial Number TRANSDUCER Schaffner‐Chase CBL6143 *** TRANSDUCER EMCO 3115 *** AMPLIFIER Agilent 8447D *** AMPLIFIER Agilent 8449B *** SPECTRUM ANALYZER Agilent 8561B *** Vertex Standard Co., Ltd.

Report number TA000657 Page 13 of 34 NAME OF TEST: Field Strength of Spurious Radiation LIMITʹS), dBc: ‐(43+10xLOG(P)) = ‐61 ( 70 Watts ) ‐(43+10xLOG(P)) = ‐58 ( 30 Watts ) High Power FREQUENCY FREQUENCY METER, C.F., ERP, ERP, TUNED, MHz EMISSION, MHz dBuV dB dBm dBc measurements exceed the requirements by more than 20 dB Vertex Standard Co., Ltd.

Report number TA000657 Page 14 of 34 NAME OF TEST: Field Strength of Spurious Radiation LIMITʹS), dBc: ‐(43+10xLOG(P)) = ‐61 ( 70 Watts ) ‐(43+10xLOG(P)) = ‐58 ( 30 Watts ) Low Power FREQUENCY FREQUENCY METER, C.F., ERP, ERP, TUNED, MHz EMISSION, MHz dBuV dB dBm dBc measurements exceed the requirements by more than 20 dB Vertex Standard Co., Ltd.

Report number TA000657 Page 15 of 34 NAME OF TEST: Emission Masks (Occupied Bandwidth) SPECIFICATION: 47 CFR 2.1049 (c) (1) GUIDE: ANSI/TIA/EIA‐603, Paragraph 2.2.11 TEST EQUIPMENT: As per previous page MEASUREMENT PROCEDURE 1. The EUT and test equipment ware set up as shown on the following page, with the spectrum analyzer connected. 2. For EUTʹs supporting audio modulation, the audio signal generator was adjusted to the frequency of maxmum response and with output level set for ±2.5kHz deviation (or 50% modulation). With level constant, the signal level was increased 16dB. 3. For EUTʹs supporting digital modulation, the digital modulation mode was operated to its maximum extent. 4. The occupied bandwidth was measured with the spectrum analyzer controls set as shown on the test results. 5. MEASUREMENT RESULTS: ATTACHED Vertex Standard Co., Ltd.

Report number TA000657 Page 16 of 34 NAME OF TEST: Emission Masks (Occupied Bandwidth) STATE: 1 : High Power REF 48.5 dBm ATTEN 10 dB 10dB/ POS PK OFFSET 44dB AVG CENTER 29.7 MHz SPAN 100 KHz RES BW 300 Hz VBW 300 Hz SWP 5 s Power: High Modulation: None 25 kHz, MASK B REF 48.5 dBm ATTEN 10 dB 10dB/ POS PK OFFSET 44dB AVG CENTER 29.7 MHz SPAN 100 KHz RES BW 300 Hz VBW 300 Hz SWP 5 s Power: High Modulation: Voice 25 kHz, MASK B Vertex Standard Co., Ltd.

Report number TA000657 Page 17 of 34 NAME OF TEST: Emission Masks (Occupied Bandwidth) STATE: 1 : High Power REF 48.5 dBm ATTEN 10 dB 10dB/ POS PK OFFSET 44dB AVG CENTER 33.35 MHz SPAN 100 KHz RES BW 300 Hz VBW 300 Hz SWP 5 s Power: High Modulation: None 25 kHz, MASK B REF 48.5 dBm ATTEN 10 dB 10dB/ POS PK OFFSET 44dB AVG CENTER 33.349 MHz SPAN 100 KHz RES BW 300 Hz VBW 300 Hz SWP 5 s Power: High Modulation: Voice 25 kHz, MASK B Vertex Standard Co., Ltd.

Report number TA000657 Page 18 of 34 NAME OF TEST: Emission Masks (Occupied Bandwidth) STATE: 1 : High Power REF 48.2 dBm ATTEN 10 dB 10dB/ POS PK OFFSET 44dB AVG CENTER 37 MHz SPAN 100 KHz RES BW 300 Hz VBW 300 Hz SWP 5 s Power: High Modulation: None 25 kHz, MASK B REF 48.2 dBm ATTEN 10 dB 10dB/ POS PK OFFSET 44dB AVG CENTER 36.999 MHz SPAN 100 KHz RES BW 300 Hz VBW 300 Hz SWP 5 s Power: High Modulation: Voice 25 kHz, MASK B Vertex Standard Co., Ltd.

Report number TA000657 Page 19 of 34 NAME OF TEST: Emission Masks (Occupied Bandwidth) STATE: 2 : Low Power REF 44.9 dBm ATTEN 10 dB 10dB/ POS PK OFFSET 44dB AVG CENTER 29.7 MHz SPAN 100 KHz RES BW 300 Hz VBW 300 Hz SWP 5 s Power: Low Modulation: None 25 kHz, MASK B REF 44.9 dBm ATTEN 10 dB 10dB/ POS PK OFFSET 44dB AVG CENTER 29.7 MHz SPAN 100 KHz RES BW 300 Hz VBW 300 Hz SWP 5 s Power: Low Modulation: Voice 25 kHz, MASK B Vertex Standard Co., Ltd.

Report number TA000657 Page 20 of 34 NAME OF TEST: Emission Masks (Occupied Bandwidth) STATE: 2 : Low Power REF 44.8 dBm ATTEN 10 dB 10dB/ POS PK OFFSET 44dB AVG CENTER 33.349 MHz SPAN 100 KHz RES BW 300 Hz VBW 300 Hz SWP 5 s Power: Low Modulation: None 25 kHz, MASK B REF 44.8 dBm ATTEN 10 dB 10dB/ POS PK OFFSET 44dB AVG CENTER 33.35 MHz SPAN 100 KHz RES BW 300 Hz VBW 300 Hz SWP 5 s Power: Low Modulation: Voice 25 kHz, MASK B Vertex Standard Co., Ltd.

Report number TA000657 Page 21 of 34 NAME OF TEST: Emission Masks (Occupied Bandwidth) STATE: 2 : Low Power REF 44.9 dBm ATTEN 10 dB 10dB/ POS PK OFFSET 44dB AVG CENTER 36.999 MHz SPAN 100 KHz RES BW 300 Hz VBW 300 Hz SWP 5 s Power: Low Modulation: None 25 kHz, MASK B REF 44.9 dBm ATTEN 10 dB 10dB/ POS PK OFFSET 44dB AVG CENTER 37 MHz SPAN 100 KHz RES BW 300 Hz VBW 300 Hz SWP 5 s Power: Low Modulation: Voice 25 kHz, MASK B Vertex Standard Co., Ltd.

Report number TA000657 Page 22 of 34 NAME OF TEST: Audio Low Pass Filter (Voice Input) SPECIFICATION: 47 CFR 2.1047 (a) GUIDE: ANSI/TIA/EIA‐603, Paragraph 2.2.15 TEST EQUIPMENT: As per attached page MEASUREMENT PROCEDURE 1. The EUT and test equipment ware set up such that the audio input was connected at the input of the modulation limiter, and the modulated stage. 2. The audio output was connected at the output to the modulated stage. 3. MEASUREMENT RESULTS: ATTACHED TRANSMITTER TEST SET‐UP TEST A: MODULATION CAPABILITY / DISTORTION TEST B: AUDIO FREQUENCY RESPONSE TEST C: HUM AND NOISE LEVEL TEST D: RESPONSE OF LOW PASS FILTER TEST E: MODULATION KIMITING Test (1) (2) (3) Sample Power (4) Supply Instruments Description Serial Number (1) AUDIO GENERATOR Agilent 8903B *** (2) COAXIAL ATTENUATOR Agilent 8498A *** (3) MODULATION ANALYZER Agilent 8901B *** (4) AUDIO ANALYZER Agilent 8903B *** Vertex Standard Co., Ltd.

Report number TA000657 Page 23 of 34 NAME OF TEST: Audio Low Pass Filter (Voice Input) STATE: 0 : General 0 -20 Response [dB] -40 -60 -80 -100 100 1000 10000 100000 Frequency [Hz] Vertex Standard Co., Ltd.

Report number TA000657 Page 24 of 34 NAME OF TEST: Audio Frequency Response SPECIFICATION: 47 CFR 2.1047 (a) GUIDE: ANSI/TIA/EIA‐603, Paragraph 2.2.6 TEST EQUIPMENT: As per previous page MEASUREMENT PROCEDURE 1. The EUT and test equipment ware set up as shown on the following page. 2. The audio signal generator was connected to the audio input circuit/microphone of the EUT. 3. The audio signal input was adjusted to obtain 20% modulation at 1kHz, and this point was taken as the 0dB reference level. 4. Which input levels hold constant and below limiting at all frequencies, the audio signal generator was varied from 100Hz to 5kHz. 5. The response in dB relative to 1kHz was then measured, using the Agilent 8901B modulation analyzer. 6. MEASUREMENT RESULTS: ATTACHED Vertex Standard Co., Ltd.

Report number TA000657 Page 25 of 34 NAME OF TEST: Audio Frequency Response STATE: 0 : General 20 16 12 8 Response [dB] 4 0 -4 -8 -12 -16 -20 100 1000 10000 Frequency [Hz] PEAK AUDIO FREQUENCY : 2700 [Hz] Vertex Standard Co., Ltd.

Report number TA000657 Page 26 of 34 NAME OF TEST: Modulation Limiting SPECIFICATION: 47 CFR 2.1047 (b) GUIDE: ANSI/TIA/EIA‐603, Paragraph 2.2.3 TEST EQUIPMENT: As per previous page MEASUREMENT PROCEDURE 1. The signal generator was connected to the input of the EUT as for ʺFrequency Response of the Modulating Circuitʺ. 2. The modulation response was measured for each of three frequencies (one of which was the frequency of maximum response), and the input voltage was varied and was observed on an Agilent 8901B modulation analyzer. 3. The input level was varied from 30% modulation (± 1.5kHz deviation) to at least 20dB higher than the saturation point. 4. Measurements ware performed for both negative and positive modulation and the respective results ware recorded. 5. MEASUREMENT RESULTS: ATTACHED Vertex Standard Co., Ltd.

Report number TA000657 Page 27 of 34 NAME OF TEST: Modulation Limiting STATE: 0 : General Positive Peak 0 dB = 4.8 [mV] 300Hz 1000Hz 2700Hz Limit 10 Frequency Deviation [kHz] 1 0 -30 -20 -10 0 10 20 30 40 MIC. Input Level [dB] Negative Peak 300Hz 1000Hz 2700Hz Limit 10 Frequency Deviation [kHz] 1 0 -30 -20 -10 0 10 20 30 40 MIC. Input Level [dB] Vertex Standard Co., Ltd.

Report number TA000657 Page 28 of 34 NAME OF TEST: Frequency Stability (Temperature Variation) SPECIFICATION: 47 CFR 2.1055 (a) (1) GUIDE: ANSI/TIA/EIA‐603, Paragraph 2.2.2 TEST CONDITIONS: As indicated TEST EQUIPMENT: As per previous page MEASUREMENT PROCEDURE 1. The EUT and test equipment ware set up as shown on the following page. 2. With all power removed, the temperature was decreased to ‐30℃ and permitted to stabilize for three hours. Power was applied and themaximum change in frequency was noted within one minute. 3. With power OFF, the temperature was raised in 10℃ steps. The sample was permitted to stabilize at each step for at least one‐half hour. Power was applied and the maximum frequency change was noted within one minute. 4. The temperature tests ware performed for the worst case. 5. MEASUREMENT RESULTS: ATTACHED Vertex Standard Co., Ltd.

Report number TA000657 Page 29 of 34 TRANSMITTER TEST SET‐UP TEST A: OPERATIONAL STABILITY TEST B: CARRIER FREQUENCY STABILITY TEST C: OPERATIONAL PERFORMANCE STABILITY TEST D: HUMIDITY TEST E: VIBRATION TEST F: ENVIRONMENTAL TEMPERATURE TEST G: FREQUENCY STABILITY, TEMPERATURE VARIATION TEST H: FREQUENCY STABILITY, VOLTAGE VARIATION Test (2) (3) Sample (1) Power (4) Supply Instruments Description Serial Number (1) TEMPERATURE CHAMBER ETAC FX4100 *** (2) COAXIAL ATTENUATOR Weinschel 53‐30‐33 *** (3) POWER METER Agilent 436A *** (4) FREQUENCY COUNTER Agilent 8901B FREQUENCY MODE *** Vertex Standard Co., Ltd.

Report number TA000657 Page 30 of 34 NAME OF TEST: Frequency Stability (Temperature Variation) STATE: 0 : General 10 8 6 4 Stability [ppm] 2 0 -2 -4 -6 -8 -10 -40 -30 -20 -10 0 10 20 30 40 50 60 70 Temperature [℃] Vertex Standard Co., Ltd.

Report number TA000657 Page 31 of 34 NAME OF TEST: Frequency Stability (Voltage Variation) SPECIFICATION: 47 CFR 2.1055 (b) GUIDE: ANSI/TIA/EIA‐603, Paragraph 2.2.2 TEST EQUIPMENT: As per previous page MEASUREMENT PROCEDURE 1. The EUT was placed in a temperature chamber at 25±5℃ and connected as for ʺFrequency Stability ‐ Temperature Variationʺ test. 2. The power supply voltage to the EUT was varied from 85% to 115% of the nominal value measured at the input to the EUT. 3. The variation in frequency was measured for the worst case. RESULTS: Frequency Stability (Voltage Variation) STATE: 0 : General LIMITʹ, ppm = 2.5 LIMITʹ, Hz = 83 % of STV Voltage Frequency, MHz Change, Hz Change, ppm 85 11.73 33.349980 ‐20 ‐0.60 100 13.80 33.349990 ‐10 ‐0.30 115 15.87 33.349960 ‐40 ‐1.20 10 8 6 4 Stability [ppm] 2 0 -2 -4 -6 -8 -10 80 90 100 110 120 Voltage [%] Vertex Standard Co., Ltd.

Report number TA000657 Page 32 of 34 NAME OF TEST: Necessary Bandwidth and Emission Bandwidth SPECIFICATION: 47 CFR 2.202 (g) MODULATION = 16K0F3E NECESSARY BANDWIDTH CALUCULATION: MAXIMUM MODULATION (M), kHz = 3 MAXIMUM DEVIATION (D), kHz = 5 CONSTANT FACTOR (K) = 1 NECESSARY BANDWIDTH (BN), kHz= (2xM) + (2xDxK) = 16 Vertex Standard Co., Ltd.

Report number TA000657 Page 33 of 34 NAME OF TEST: Receiver Spurious Emissions (Conducted) STATE: 0 : General All other emissions in the required measurement range are more than 20dB below the required limits. MEASUREMENT RESULTS FREQUENCY FREQUENCY LEVEL, LEVEL, TUNED, MHz EMISSION, MHz dBm nW measurements exceed the requirements by more than 20 dB Vertex Standard Co., Ltd.

Report number TA000657 Page 34 of 34 NAME OF TEST: Receiver Spurious Emissions (Radiated) STATE: 0 : General All other emissions in the required measurement range are more than 20dB below the required limits. MEASUREMENT RESULTS FREQUENCY FREQUENCY LEVEL, @m CF, uV/m TUNED, MHz EMISSION, MHz dBuV dB 37.000 218.800 21.3 3 ‐10.0 31.3 37.000 437.600 30.0 3 ‐6.5 36.5 33.350 459.450 27.8 3 ‐7.1 34.9 37.000 492.300 30.0 3 ‐7.9 37.9 29.700 521.400 24.1 3 ‐8.2 32.3 37.000 547.000 32.9 3 ‐4.7 37.6 Vertex Standard Co., Ltd.


Document Created: 2008-12-10 15:24:16
Document Modified: 2008-12-10 15:24:16
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC