test report

FCC ID: K660H464X10

Test Report

Download: PDF
FCCID_1477842

RFT Issue Date: 3 June, 2011 Report No.: RY1106Z03R1 Model: BU-2 TEST REPORT For Bluetooth Adapter Unit In conformity with FCC CFR 47 Part15 / RSS-210, RSS-Gen Model: BU-2 FCC ID/ IC Certification No.: K660H464X10 / 511B- 0H464X10 Test Item: Bluetooth Adapter Unit Report No: RY1106Z03R1 Issue Date: 3 June 2011 Prepared for Vertex Standard Co., Ltd. 4-8-8, Nakameguro Meguro-ku, Tokyo 153-8644 Japan Prepared by RF Technologies Ltd. 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645 FAX: +81+(0)45- 534-0646 This report shall not be reproduced, except in full, without the written permission of RF Technologies Ltd. The test results relate only to the item(s) tested. RF Technologies Ltd. is managed to ISO17025 and has the necessary knowledge and test facilities for testing according to the referenced standards. RF Technologies Ltd. Page 1 of 37 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 3 June, 2011 Report No.: RY1106Z03R1 Model: BU-2 Table of contents 1 General information ...................................................................................................................... 3 1.1 Product description ................................................................................................................................................ 3 1.2 Test(s) performed/ Summary of test result ............................................................................................................ 3 1.3 Test facility ............................................................................................................................................................ 4 1.4 Measurement uncertainty ....................................................................................................................................... 4 1.5 Summary of test results.......................................................................................................................................... 5 1.5.1 Table of test summary.................................................................................................................................... 5 1.6 Setup of equipment under test (EUT) .................................................................................................................... 5 1.6.1 Test configuration of EUT ............................................................................................................................. 5 1.6.2 Operating condition: ...................................................................................................................................... 6 1.6.3 Setup diagram of tested system:..................................................................................................................... 6 1.7 Equipment modifications ....................................................................................................................................... 6 1.8 Deviation from the standard .................................................................................................................................. 6 2 Test procedure and test data ........................................................................................................ 7 2.1 Occupied Bandwidth (20 dB / 99%) ...................................................................................................................... 7 2.2 Hopping Carrier Frequency Separation ................................................................................................................. 9 2.3 Number of Hopping Channel ............................................................................................................................... 11 2.4 Average Time of Occupancy ............................................................................................................................... 12 2.5 Peak Output Power .............................................................................................................................................. 14 2.6 Conducted Spurious Emissions (Antenna Port) ................................................................................................... 15 2.7 Transmitter Radiated spurious emissions ............................................................................................................ 18 2.7.1 Below 30 MHz ............................................................................................................................................. 20 2.7.2 Between 30 – 1000 MHz ............................................................................................................................. 21 2.7.3 Above 1000 MHz......................................................................................................................................... 23 2.8 Transmitter AC power line conducted emissions ................................................................................................ 25 2.9 Receiver Radiated spurious emissions ................................................................................................................. 28 2.9.1 Between 30 – 1000 MHz ............................................................................................................................. 28 2.9.2 Above 1000 MHz......................................................................................................................................... 30 2.10 Receiver AC power line conducted emissions ..................................................................................................... 31 3 Test setup photographs ............................................................................................................... 34 3.1 Definition of the EUT axis................................................................................................................................... 34 3.2 AC power line conducted emissions .................................................................................................................... 35 3.3 Radiated spurious emissions ................................................................................................................................ 36 4 List of utilized test equipment/ calibration ............................................................................... 37 History Report No. Date Revisions Issued By RY1106Z03R1 3 June, 2011 Initial Issue K.Ohnishi RF Technologies Ltd. Page 2 of 37 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

Issuc Date:3 Junヽ 2011 IΠ RepOrt No■ Model:BU‐ 2 RY l106加 Rl Generalinformation 1.l Prrlduct descnptioll Test ttem Bluetooth Adapter unit Manuf∝ turer Vcrtcx Standard co,Ltd Address 4‐ 8‐ 8,Nakameslro MCgro― ku,To町 o153 8644 Japan Model BU‐ 2 FCC ID K660H464X10 IC CerlincatiOn No 51lB‐ OH464X10 Serial numbers TPll,TP14 Flut― lc泰轍 勁珂卸 o Tx/Rx Fleq(2402‐ 2480 NIHzl ● d‖ ator Frequencts 26 MHz Tlpe ofModulation GFSK RF Otltput Powcr 7 22dBm(measurcd atthe antenna tenminai) Antenna Cain 1 9 dBi(Chip antennal Receipt date of EUT 20 ApnL 2011 Nominal power source voltages DC 40V 1.2 Test(O perfOrmed′ Sumlllary oF test result Tcst specincaliOn(s) FCC CFR 47 Par115(OctobCr l,2009)/RSS‐ 210 1ssue 8,RSS‐ Cen lsstle 3 Test methodKs) ANSI C63 4:2003 TeS(S)Started 22 April,2011 TCS(9 COmpleted l June,2011 Purpose oftes(s) Crallt for CertincatiOn of FCC/1C Summa● oFtest result Complied Note The abovejudulent、 only bascd on the measuremcnt data and docs notinclude thc mcasurement unccrlainty Accoldingly,the statcmcnt below is applied to ale test rcsult Thc EUT comphes witllthe‖ mlt rcquired in ule standard in case that thc maran iS nOt icss than the measurement unceltain,in tlle Laboratory Compliance ofthe EUT is morc prrlbable than non― compliance is cぉ c dlatthe margin is less ulan tllc mcasurcmellt uncertain,in thC Laborato, Test engincer Revlc、 ver EMC tesung Department RFT∝ bno[嘔 i‐ Ltd Page 3 or 37 472 Nipド ho Kohok● kじ Yokoh枷 ■ 2230057.Japm TCに ,hOno+81+ll● 5534つ 645=慈:+31+ll 5‐ 5 0 6 WeЫ httpノ ハ ″,ハ ⅣnJp

RFT Issue Date: 3 June, 2011 Report No.: RY1106Z03R1 Model: BU-2 1.3 Test facility The Federal Communications Commission has reviewed the technical characteristics of the test facilities at RF Technologies Ltd., located in 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan, and has found these test facilities to be in compliance with the requirements of 47 CFR Part 15, section 2.948, per October 1, 2007. The description of the test facilities has been filed under registration number 319924 at the Office of the Federal Communications Commission. The facility has been added to the list of laboratories performing these test services for the public on a fee basis. The list of all public test facilities is available on the Internet at http://www.fcc.gov. Registered by Voluntary Control Council for Interference by Information Technology Equipment (VCCI) Each registered facility number is as follows; Test site (Semi-Anechoic chamber 3m) R-2393 Test site (Shielded room) C-2617 Registered by Industry Canada (IC): The registered facility number is as follows; Test site No. 1 (Semi-Anechoic chamber 3m): 6974A-1 Accredited by National Voluntary Laboratory Accreditation Program (NVLAP) for the emission tests stated in the scope of the certificate under Certificate Number 200780-0 This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. 1.4 Measurement uncertainty The treatment of uncertainty is based on the general matters on the definition of uncertainty in “Guide to the expression of uncertainty in measurement (GUM)” published by ISO. The Lab’s uncertainty is determined by referring UKAS Publication LAB34: 2002 “The Expression of Uncertainty in EMC Testing” and CISPR16-4-2: 2003 “Uncertainty in EMC Measurements”. The uncertainty of the measurement result in the level of confidence of approximately 95% (k=2) is as follows; RF Conducted level: +/- 1.10dB Conducted emission: +/- 1.90dB (10kHz – 30MHz) Radiated emission (9kHz - 30MHz): +/- 2.79dB Radiated emission (30MHz - 1000 MHz): +/- 5.90dB Radiated emission (1GHz - 18GHz): +/- 5.77dB Radiated emission (18GHz - 26GHz): +/- 5.89dB RF Technologies Ltd. Page 4 of 37 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 3 June, 2011 Report No.: RY1106Z03R1 Model: BU-2 1.5 Summary of test results 1.5.1 Table of test summary Requirement of; Section in FCC15 Section in Result Sample Section in RSS210/ this report RSS-Gen 1.5.1 Occupied Bandwidth (20 dB/99%) 15.247(a)(1) A8.1(b) Complied A1 2.1 1.5.2 Hopping Carrier Frequency Separation 15.247(a)(1) A8.1(b) Complied A1 2.2 1.5.3 Number of Hopping Channel 15.247(a)(1)(iii) A8.1(d) Complied A1 2.3 1.5.4 Average Time of Occupancy 15.247(a)(1)(iii) A8.1(d) Complied A1 2.4 1.5.5 Peak Output Power 15.247(a)(1)/(b)(1) A8.4(2) Complied A1 2.5 1.5.6 Peak Power Spectral Density 15.247(e) A8.2(b) N/A - - 1.5.7 Conducted Spurious Emissions 15.247(d) A8.5 Complied A1 2.6 1.5.8 Transmitter Radiated Spurious Emissions 15.205(b)/15.209 RSS-Gen Complied A2 2.7 7.2.2, 7.2.5 1.5.9 Transmitter AC Power Line 15.207 RSS-Gen Complied A2 2.8 Conducted Emissions 7.2.4 1.5.10 Receiver Radiated Spurious Emissions 15.109 RSS-Gen 6 Complied A2 2.9 1.5.11 Receiver AC Power Line 15.107 RSS-Gen Complied A2 2.10 Conducted Emissions 7.2.4 1.6 Setup of equipment under test (EUT) 1.6.1 Test configuration of EUT Equipment(s) under test: Item Manufacturer Model No. Serial No. Remark A1 Bluetooth Adapter Unit Vertex Standard Co., Ltd. BU-2 TP11 For RF conducted test A2 Bluetooth Adapter Unit Vertex Standard Co., Ltd. BU-2 TP14 For RF radiated test Support Equipment(s): Item Manufacturer Model No. Serial No. B Test Jig Vertex Standard Co., Ltd. - - C DC power supply KIKUSUI PMC18-3A DF002941 D Personal Computer DELL VOSTRO 1520 08317 E AC Adaptor DELL LA65NS1-00 CN-0YD637-71615-965-3E28 Connected cable(s): No. Item Identification Shielded Ferrite Connector Type Length (Manu.e.t.c) Core Shielded (m) YES / NO YES / NO YES / NO 1 RS232C cable - No No Yes 2.05 2 USB-232C cable ELECOM Yes No Yes 0.50 3 AC power cable - No No No 1.50 4 DC power cable DELL No No No 1.80 5 AC power cable DELL No No No 0.90 RF Technologies Ltd. Page 5 of 37 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 3 June, 2011 Report No.: RY1106Z03R1 Model: BU-2 1.6.2 Operating condition: Operating mode: The EUT was tested under the following test mode prepared by the applicant: (1-1) GFSK modulation, Continuous transmission with DH5 PACKET at hopping off (2402MHz) (1-2) GFSK modulation, Continuous transmission with DH5 PACKET at hopping off (2441MHz) (1-3) GFSK modulation, Continuous transmission with DH5 PACKET at hopping off (2480MHz) (1-4) π/4DQPSK modulation, Continuous transmission with DH5 PACKET at hopping off (2402MHz) (1-5) π/4DQPSK modulation, Continuous transmission with DH5 PACKET at hopping off (2441MHz) (1-6) π/4DQPSK modulation, Continuous transmission with DH5 PACKET at hopping off (2480MHz) (1-7) 8DPSK modulation, Continuous transmission with DH5 PACKET at hopping off (2402MHz) (1-8) 8DPSK modulation, Continuous transmission with DH5 PACKET at hopping off (2441MHz) (1-9) 8DPSK modulation, Continuous transmission with DH5 PACKET at hopping off (2480MHz) (1-10) Continuous transmission with DH5 PACKET at hopping on (2-1) Continuous receiving 1.6.3 Setup diagram of tested system: A: B: D: Bluetooth Adapter Unit Test Jig 1 2 Personal Computer (EUT) 4 lead wire: 0.15m 2 lead wire: 0.15m 4 C: : Ferrite Core DC power E: NEC/TOKIN: ESD-SR-150 Supply AC Adaptor 3 5 AC120V, 60Hz AC100V, 60Hz These equipments are connected to achieve the test mode operations temporally. 1.7 Equipment modifications No modifications have been made to the equipment in order to achieve compliance with the applicable standards described in clause 1.2. 1.8 Deviation from the standard No deviations from the standards described in clause 1.2. RF Technologies Ltd. Page 6 of 37 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 3 June, 2011 Report No.: RY1106Z03R1 Model: BU-2 2 Test procedure and test data 2.1 Occupied Bandwidth (20 dB / 99%) Test setup Test setup is the following drawing. The antenna port of EUT was connected to the spectrum analyzer. EUT Antenna Port Spectrum Analyzer Test procedure Measurement procedures were implemented according to the method of ANSI C63.4: 2003 clauses 13.1.7. The EUT antenna port connected to the spectrum analyzer. The RBW is set to 1% to 3% of the measured 20dB bandwidth. The VBW is set to 3 times of the RBW. The sweep time is coupled appropriate. Limitation There are no limitations. The measurement value is used to calculation of the limitation of the channel separation and the emission designator. Test equipment used (refer to List of utilized test equipment) SA06 CL22 Test results Operating Transmission Channel Transmission Bandwidth [MHz] Mode Frequency 20dB 99% Low (0ch) 2402 1.110 0.950 GFSK Middle (39ch) 2441 1.120 0.950 (1Mbps) High (78ch) 2480 1.090 0.920 Low (0ch) 2402 1.400 1.240 π/4DQPSK Middle (39ch) 2441 1.390 1.240 (2Mbps) High (78ch) 2480 1.370 1.220 Low (0ch) 2402 1.390 1.240 8DPSK Middle (39ch) 2441 1.390 1.230 (3Mbps) High (78ch) 2480 1.380 1.230 RF Technologies Ltd. Page 7 of 37 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 3 June, 2011 Report No.: RY1106Z03R1 Model: BU-2 Test Data Tested Date: 22 April, 2011 Temperature: 21 ˚C Humidity: 49 % Atmos. Press: 1021 hPa 20dB Bandwidth * RBW 100 kHz Marker 1 [T1 ] * VBW 100 kHz 3.17 dBm Ref 20 dBm * Att 30 dB SWT 2.5 ms 2.402030000 GHz 20 ndB [T1] 20.00 dB BW 1.400000000 MHz Temp 1 [T1 ndB] A 10 1 -16.24 dBm 1 PK 2.401340000 GHz VIEW 0 Temp 2 [T1 ndB] -17.09 dBm 2.402740000 GHz -10 T1 T2 -20 -30 -40 -50 -60 -70 -80 Center 2.402 GHz 500 kHz/ Span 5 MHz 99% Occupied Bandwidth * RBW 100 kHz Marker 1 [T1 ] * VBW 100 kHz 3.15 dBm Ref 20 dBm * Att 30 dB SWT 2.5 ms 2.402030000 GHz 20 OBW 1.240000000 MHz Temp 1 [T1 OBW] -11.13 dBm A 10 1 2.401410000 GHz 1 PK Temp 2 [T1 OBW] VIEW 0 -10.34 dBm 2.402650000 GHz T1 T2 -10 -20 -30 -40 -50 -60 -70 -80 Center 2.402 GHz 500 kHz/ Span 5 MHz RF Technologies Ltd. Page 8 of 37 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 3 June, 2011 Report No.: RY1106Z03R1 Model: BU-2 2.2 Hopping Carrier Frequency Separation Test setup Test setup is the following drawing. The antenna port of EUT was connected to the spectrum analyzer. EUT Antenna Port Spectrum Analyzer Test procedure The EUT antenna port connected to the spectrum analyzer. The RBW is set to more than 1% of its span. The VBW is set to more than RBW. The sweep time is coupled appropriate. Limitation 15.247(a)(1) frequency hopping systems operating in the 2400-2483.5 MHz band may have hopping channel carrier frequencies that are separated by 25 kHz or two-thirds of the 20 dB bandwidth of the hopping channel, whichever is greater, provided the systems operate with an output power no greater than 125 mW. Test equipment used (refer to List of utilized test equipment) SA06 CL22 Test results – comply with the limitation Operating Measured Measured Frequency Two-third of Frequency Separation Mode Channel (MHz) the 20dB bandwidth (MHz) (MHz) GFSK Middle (39ch) 2441 0.747 1.0 π/4DQPSK Middle (39ch) 2441 0.934 1.0 8DPSK Middle (39ch) 2441 0.927 1.0 Test Data Tested Date: 22 April, 2011 Temperature: 21 ˚C Humidity: 49 % Operating mode: GFSK Atmos. Press: 1021 hPa * RBW 300 kHz Marker 1 [T1 ] VBW 1 MHz 4.65 dBm Ref 10 dBm * Att 30 dB SWT 2.5 ms 2.441000000 GHz 10 Delta 2 [T1 ] -0.14 dB 1.000000000 MHz A 8 Delta 1 [T1 ] 1 PK 0.05 dB VIEW 6 -1.000000000 MHz 1 1 2 4 2 0 -2 -4 -6 -8 -10 Center 2.441 GHz 500 kHz/ Span 5 MHz RF Technologies Ltd. Page 9 of 37 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 3 June, 2011 Report No.: RY1106Z03R1 Model: BU-2 Operating mode: π/4DQPSK * RBW 1 MHz Marker 1 [T1 ] VBW 3 MHz 3.73 dBm Ref 8 dBm * Att 30 dB SWT 2.5 ms 2.441000000 GHz 8 Delta 2 [T1 ] -0.10 dB 1.000000000 MHz A 7 Delta 1 [T1 ] 1 PK -0.08 dB VIEW 6 -1.000000000 MHz 5 4 1 1 2 3 2 1 0 -1 -2 Center 2.441 GHz 500 kHz/ Span 5 MHz Operating mode: 8DPSK * RBW 1 MHz Marker 1 [T1 ] VBW 3 MHz 3.88 dBm Ref 8 dBm * Att 30 dB SWT 2.5 ms 2.441000000 GHz 8 Delta 2 [T1 ] 0.01 dB 1.000000000 MHz A 7 Delta 1 [T1 ] 1 PK -0.01 dB VIEW 6 -1.000000000 MHz 5 1 1 2 4 3 2 1 0 -1 -2 Center 2.441 GHz 500 kHz/ Span 5 MHz RF Technologies Ltd. Page 10 of 37 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 3 June, 2011 Report No.: RY1106Z03R1 Model: BU-2 2.3 Number of Hopping Channel Test setup Test setup is the following drawing. The antenna port of EUT was connected to the spectrum analyzer. EUT Antenna Port Spectrum Analyzer Test procedure The EUT antenna port connected to the spectrum analyzer. The RBW is set to more than 1% of its span. The VBW is set to more than RBW. The sweep time is coupled appropriate. The span is set to cover the authorized band. The analyzer is set to MAX HOLD. The EUT is hopping operation. Limitation 15.247(a) (1) (iii) (iii) Frequency hopping systems in the 2400-2483.5 MHz band shall use at least 15 channels. Test equipment used (refer to List of utilized test equipment) SA06 CL22 Test results – Comply with the limitation Hopping channel: 79 channels Test Data Tested Date: 22 April, 2011 Temperature: 21 ˚C Humidity: 49 % Atmos. Press: 1021 hPa * RBW 1 MHz Marker 1 [T1 ] * RBW 1 MHz Marker 1 [T1 ] * RBW 1 MHz Marker 2 [T1 ] VBW 3 MHz 4.44 dBm VBW 3 MHz 4.65 dBm VBW 3 MHz 4.89 dBm Ref 8 dBm * Att 30 dB SWT 2.5 ms 2.402000000 GHz Ref 8 dBm * Att 30 dB SWT 2.5 ms 2.428000000 GHz Ref 8 dBm * Att 30 dB SWT 2.5 ms 2.480000000 GHz 8 Marker 2 [T1 ] 8 Marker 2 [T1 ] 8 Marker 1 [T1 ] 4.71 dBm 4.82 dBm 4.85 dBm A A 2.456000000 GHz A 7 2.428000000 GHz 7 2.456000000 GHz 7 1 PK 1 PK 1 PK VIEW VIEW VIEW 6 6 6 2 1 2 5 2 15 5 1 4 4 4 3 3 3 2 2 2 1 1 1 0 0 0 -1 -1 -1 -2 -2 -2 Start 2.4 GHz 2.8 MHz/ Stop 2.428 GHz Start 2.428 GHz 2.8 MHz/ Stop 2.456 GHz Start 2.456 GHz 2.8 MHz/ Stop 2.484 GHz RF Technologies Ltd. Page 11 of 37 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 3 June, 2011 Report No.: RY1106Z03R1 Model: BU-2 2.4 Average Time of Occupancy Test setup Test setup is the following drawing. The antenna port of EUT was connected to the spectrum analyzer. EUT Antenna Port Spectrum Analyzer Test procedure The EUT antenna port connected to the spectrum analyzer. The RBW is set to 1 MHz. The VBW is set to more than RBW. The sweep time is coupled appropriate. The span is set to 0 MHz and single sweep with video triggered. The EUT is hopping operation. The average time of occupancy within the 31.6 seconds (79 channels * 0.4) is calculated as follows in accordance with Bluetooth formula; In case of DH5: (average time of occupancy) = (pulse width) * (1600 / 6) / 79 * 31.6 Limitation 15.247(a)(1)(iii) The average time of occupancy on any channel shall not be greater than 0.4 seconds within a period of 0.4 seconds multiplied by the number of hopping channels employed. Test equipment used (refer to List of utilized test equipment) SA06 CL22 Test results – comply with the limitation. Operating Mode Frequency [MHz] Transmission Pulse width Time of occupancy Packet Type (msec) (msec) 2402 DH5 2.920 309.495 GFSK 2441 DH5 2.920 309.495 2480 DH5 2.920 309.495 2402 DH5 2.930 310.555 π/4DQPSK 2441 DH5 2.930 310.555 2480 DH5 2.930 310.555 2402 DH5 2.930 310.555 8DPSK 2441 DH5 2.930 310.555 2480 DH5 2.930 310.555 RF Technologies Ltd. Page 12 of 37 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 3 June, 2011 Report No.: RY1106Z03R1 Model: BU-2 Test Data Tested Date: 22 April, 2011 Temperature: 21 ˚C Humidity: 49 % Atmos. Press: 1021 hPa RBW 1 MHz Delta 2 [T1 ] VBW 3 MHz 0.05 dB Ref 30 dBm * Att 50 dB SWT 5 ms 3.770000 ms 30 Marker 1 [T1 ] 4.43 dBm 15.670110 as A 20 Delta 1 [T1 ] 1 PK -0.15 dB VIEW TRG 10 2.920000 ms 1 1 2 0 -10 -20 TRG -20 dBm -30 -40 -50 -60 GFSK DH5 2402MHz -70 Center 2.402 GHz 500 µs/ RBW 1 MHz Delta 2 [T1 ] VBW 3 MHz 0.08 dB Ref 30 dBm * Att 50 dB SWT 5 ms 3.770000 ms 30 Marker 1 [T1 ] 3.16 dBm 0.000000 s A 20 Delta 1 [T1 ] 1 PK -0.96 dB VIEW TRG 10 2.930000 ms 1 1 2 0 -10 -20 TRG -20 dBm -30 -40 -50 -60 π/4DQPSK DH5 2402MHz -70 Center 2.402 GHz 500 µs/ RBW 1 MHz Delta 2 [T1 ] VBW 3 MHz 0.37 dB Ref 30 dBm * Att 50 dB SWT 5 ms 3.770000 ms 30 Marker 1 [T1 ] 2.87 dBm 0.000000 s A 20 Delta 1 [T1 ] 1 PK -0.39 dB VIEW TRG 10 2.930000 ms 1 1 2 0 -10 -20 TRG -27 dBm -30 -40 -50 -60 8DPSK DH5 2402MHz -70 Center 2.402 GHz 500 µs/ RF Technologies Ltd. Page 13 of 37 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 3 June, 2011 Report No.: RY1106Z03R1 Model: BU-2 2.5 Peak Output Power Test setup Test setup is the following drawing. The antenna port of EUT was connected to the spectrum analyzer. EUT Antenna Port Spectrum Analyzer Test procedure The EUT antenna port connected to the spectrum analyzer. The RBW is set to the greater than 20dB bandwidth. The VBW is set to three times of RBW. The sweep time is coupled appropriate. The span is set to cover the carrier output spectrum. The analyzer is set to MAX HOLD. The EUT is set measured transmission channel under hopping off mode. Limitation 15.247(a) (1) Frequency hopping systems operating in the 2400-2483.5 MHz band may have hopping channel carrier frequencies that are separated by 25 kHz or two-thirds of the 20 dB bandwidth of the hopping channel, whichever is greater, provided the systems operate with an output power no greater than 125 mW(21dBm). Test equipment used (refer to List of utilized test equipment) SA06 CL22 Test results – comply with the limitation. Operating Mode Transmission Output power Output power Channel (dBm) (mW) (Frequency: MHz) [Result] [Result] Low (2402) 5.59 3.62 GFSK Middle (2441) 5.82 3.82 High (2480) 5.91 3.90 Low (2402) 7.03 5.05 π/4DQPSK Middle (2441) 6.40 4.37 High (2480) 6.17 4.14 Low (2402) 7.22 5.27 8DPSK Middle (2441) 6.62 4.59 High (2480) 6.23 4.20 Test Data Tested Date: 1 June, 2011 Temperature: 21 ˚C Humidity: 45 % * RBW 3 MHz Marker 1 [T1 ] Atmos. Press: 1019 hPa * VBW 10 MHz 7.22 dBm Ref 30 dBm * Att 40 dB SWT 2.5 ms 2.402000000 GHz 30 B 20 1 PK VIEW 10 1 0 TDF -10 -20 -30 -40 -50 -60 8DPSK 2402MHz -70 Center 2.402 GHz 1 MHz/ Span 10 MHz RF Technologies Ltd. Page 14 of 37 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 3 June, 2011 Report No.: RY1106Z03R1 Model: BU-2 2.6 Conducted Spurious Emissions (Antenna Port) Test setup Test setup is the following drawing. The antenna port of EUT was connected to the spectrum analyzer. EUT Antenna Port Spectrum Analyzer Test procedure (Band Edge) Use the following spectrum analyzer settings: Span = wide enough to capture the peak level of the emission operating on the channel closest to the band edge, as well as any modulation products which fall outside of the authorized band of operation RBW ≥ 1% of the span VBW ≥ RBW Sweep = auto Detector function = peak Trace = max hold Test procedure (Conducted spurious emissions) The EUT antenna port connected to the spectrum analyzer. The RBW is set to 100 kHz. The VBW is set to 300 kHz. The sweep time is set to the coupled. The spectrum is cheated from 30 MHz to 25 GHz. The EUT is set measured transmission channel under hopping off mode. Limitation 15.247(d) In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. Test equipment used (refer to List of utilized test equipment) SA06 CL22 Test results – comply with the limitation. RF Technologies Ltd. Page 15 of 37 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 3 June, 2011 Report No.: RY1106Z03R1 Model: BU-2 Test Data Tested Date: 1 June, 2011 Temperature: 21 ˚C Humidity: 45 % Atmos. Press: 1019 hPa Restricted Band Edge * RBW 1 MHz Marker 1 [T1 ] * RBW 1 MHz Marker 1 [T1 ] VBW 3 MHz -41.35 dBm VBW 3 MHz -31.32 dBm Ref 30 dBm * Att 40 dB SWT 2.5 ms 2.390000000 GHz Ref 30 dBm * Att 40 dB SWT 2.5 ms 2.483500000 GHz 30 30 B B GFSK 20 20 1 PK 1 PK VIEW VIEW 10 10 0 0 -10 -10 D1 -15.81 dBm D1 -15.43 dBm -20 -20 1 -30 -30 1 -40 -40 -50 -50 -60 -60 F1 F1 -70 -70 Start 2.31 GHz 10 MHz/ Stop 2.41 GHz Start 2.47 GHz 3 MHz/ Stop 2.5 GHz * RBW 1 MHz Marker 1 [T1 ] * RBW 1 MHz Marker 1 [T1 ] VBW 3 MHz -42.62 dBm VBW 3 MHz -31.90 dBm Ref 30 dBm * Att 40 dB SWT 2.5 ms 2.390000000 GHz Ref 30 dBm * Att 40 dB SWT 2.5 ms 2.483500000 GHz 30 30 B B π/4DQPSK 20 20 1 PK 1 PK VIEW VIEW 10 10 0 0 -10 -10 D1 -15.04 dBm D1 -15.83 dBm -20 -20 -30 -30 1 -40 1 -40 -50 -50 -60 -60 F1 F1 -70 -70 Start 2.31 GHz 10 MHz/ Stop 2.41 GHz Start 2.47 GHz 3 MHz/ Stop 2.5 GHz * RBW 1 MHz Marker 1 [T1 ] * RBW 1 MHz Marker 1 [T1 ] VBW 3 MHz -42.18 dBm VBW 3 MHz -31.63 dBm Ref 30 dBm * Att 40 dB SWT 2.5 ms 2.390000000 GHz Ref 30 dBm * Att 40 dB SWT 2.5 ms 2.483500000 GHz 30 30 B B 20 20 1 PK 8DPSK 1 PK VIEW VIEW 10 10 0 0 -10 -10 D1 -14.85 dBm D1 -15.9 dBm -20 -20 1 -30 -30 -40 1 -40 -50 -50 -60 -60 F1 F1 -70 -70 Start 2.31 GHz 10 MHz/ Stop 2.41 GHz Start 2.47 GHz 3 MHz/ Stop 2.5 GHz RF Technologies Ltd. Page 16 of 37 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 3 June, 2011 Report No.: RY1106Z03R1 Model: BU-2 Worst Configuration (2402MHz, 8DPSK) * RBW 100 kHz Marker 1 [T1 ] * RBW 100 kHz Marker 1 [T1 ] VBW 300 kHz -46.22 dBm VBW 300 kHz -41.32 dBm Ref 20 dBm * Att 30 dB SWT 700 ms 4.811420000 GHz Ref 20 dBm * Att 30 dB SWT 600 ms 7.204000000 GHz 20 20 10 30MHz to 7GHz B 10 7GHz to 13GHz B 1 PK 1 PK VIEW VIEW 0 0 -10 -10 D1 -15.07 dBm D1 -15.07 dBm -20 -20 -30 -30 1 -40 -40 1 -50 -50 -60 -60 -70 -70 -80 -80 Start 30 MHz 697 MHz/ Stop 7 GHz Start 7 GHz 600 MHz/ Stop 13 GHz * RBW 100 kHz * RBW 100 kHz VBW 300 kHz VBW 300 kHz Ref 20 dBm * Att 30 dB SWT 600 ms Ref 20 dBm * Att 30 dB SWT 600 ms 20 20 10 13GHz to 19GHz B 10 19GHz to 25GHz B 1 PK 1 PK VIEW VIEW 0 0 -10 -10 D1 -15.07 dBm D1 -15.07 dBm -20 -20 -30 -30 -40 -40 -50 -50 -60 -60 -70 -70 -80 -80 Start 13 GHz 600 MHz/ Stop 19 GHz Start 19 GHz 600 MHz/ Stop 25 GHz RF Technologies Ltd. Page 17 of 37 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 3 June, 2011 Report No.: RY1106Z03R1 Model: BU-2 2.7 Transmitter Radiated spurious emissions Test setup Test setup was implemented according to the method of ANSI C63.4: 2003 clause 6 “General requirements for EUT equipment arrangements and operation”, clause 8.2 and Annex H.3 “Radiated emission measurements setup”. Test setup for below 30 MHz Loop Antenna 3.0m EUT Test Receiver 0.8m Pre-amplifier Test setup for 30 MHz to 1000MHz 1.0 to 4.0 m Bilogical Antenna EUT 3.0m 0.8m Test setup for above 1 GHz 1.0 to 4.0 m Horn Antenna EUT 3.0m 0.8m RF Technologies Ltd. Page 18 of 37 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 3 June, 2011 Report No.: RY1106Z03R1 Model: BU-2 Test procedure Measurement procedures were implemented according to the method of ANSI C63.4: 2003 clauses 8.2. The EUT is place on a non-conducted table which is 0.8m height from a ground plane and the measurement antenna to EUT distance is 3 meters. The turn table is rotated for 360 degrees to determine the maximum emission level. In the frequency range of 9 kHz to 30 MHz, a calibrated loop antenna was positioned with its plane vertical at the distance 3m from the EUT with an extrapolation of corrected distance factor and rotated about its vertical axis for maximum response at each azimuth about the EUT. For certain applications, the loop antenna also needs to be positioned horizontally. The center of the loop shall be 1 m above the ground. In the frequency above 30 MHz, the antenna height scanned between 1m and 4m, and the antenna rotated to repeat the measurements for both the horizontal and vertical antenna polarizations. EUT is placed at three different orientations (X, Y and Z axis) in order to find the worst orientation. The spectrum analyzer and receiver is set to the followings; Below 30 MHz: RBW=10 kHz, VBW= 30 kHz Final measurement is carried out with a receiver RBW of 9 kHz (QP) Between 30 - 1000 MHz: RBW=100 kHz, VBW= 300 kHz Final measurement is carried out with a receiver RBW of 120 kHz (QP) Above 1000 MHz: Peak measurement- RBW=1 MHz, VBW= 1 MHz Average measurement - RBW=1 MHz, VBW=10 Hz Applicable rule and limitation §15.205 restricted bands of operation Except as shown in paragraph 15.205 (d) of this section, only spurious emissions are permitted in any of the frequency bands listed below: MHz MHz MHz GHz 0.090 - 0.110 16.42 - 16.423 399.9 - 410 4.5 - 5.15 0.490 - 0.510 16.69475 - 16.69525 608 - 614 5.35 - 5.46 2.1735 - 2.1905 16.80425 - 16.80475 960 - 1240 7.25 - 7.75 4.125 - 4.128 25.5 - 25.67 1300 - 1427 8.025 - 8.5 4.17725 - 4.17775 37.5 - 38.25 1435 - 1626.5 9.0 - 9.2 4.20725 - 4.20775 73 - 74.6 1645.5 - 1646.5 9.3 - 9.5 6.215 - 6.218 74.8 - 75.2 1660 - 1710 10.6 - 12.7 6.26775 - 6.26825 108 - 121.94 1718.8 - 1722.2 13.25 - 13.4 6.31175 - 6.31225 123 - 138 2200 - 2300 14.47 - 14.5 8.291 - 8.294 149.9 - 150.05 2310 - 2390 15.35 - 16.2 8.362 - 8.366 156.52475 - 156.52525 2483.5 - 2500 17.7 - 21.4 8.37625 - 8.38675 156.7 - 156.9 2690 - 2900 22.01 - 23.12 8.41425 - 8.41475 162.0125 - 167.17 3260 - 3267 23.6 - 24.0 12.29 - 12.293 167.72 - 173.2 3332 - 3339 31.2 - 31.8 12.51975 - 12.52025 240 - 285 3345.8 - 3358 36.43 - 36.5 12.57675 - 12.57725 322 - 335.4 3600 - 4400 (1) 15.205(b) except as provided in paragraphs (d) and (e), the field strength of emissions appearing within these frequency bands shall not exceed the limits shown in Section 15.209. At frequencies equal to or less than 1000 MHz, compliance with the limits in Section 15.209 shall be demonstrated using measurement instrumentation employing a CISPR quasi-peak detector. Above 1000 MHz, compliance with the emission limits in Section 15.209 shall be demonstrated based on the average value of the measured emissions. The provisions in Section 15.35 apply to these measurements. RF Technologies Ltd. Page 19 of 37 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 3 June, 2011 Report No.: RY1106Z03R1 Model: BU-2 15.209( a) Except as provided elsewhere in this Subpart, the emissions from an intentional radiator shall not exceed the field strength levels specified in the following table Frequency Field Strength Measurement Distance (MHz) (uV/m) (m) 0.009 - 0.490 2400/F (kHz) 300 0.490 - 1.705 24000/F (kHz) 30 1.705 - 30.0 30 30 30 – 88 100 3 88 –216 150 3 216 – 960 200 3 Above 960 500 3 In the emission table above, the tighter limit applies at the band edges. The level of any unwanted emissions from an intentional radiator operating under these general provisions shall not exceed the level of the fundamental emission. The emission limits shown in the above table are based on measurements employing a CISPR quasi-peak detector except for the frequency bands 9-90 kHz, 110-490 kHz. Radiated emission limits in the above bands are based on measurements employing an average detector. Test results - Complied with requirement. Test Data 2.7.1 Below 30 MHz Test equipment used (refer to List of utilized test equipment) LP01 CL11 TR06 Tested Date: 1 June, 2011 Temperature: 21 ˚C Humidity: 45 % Atmos. Press: 1019 hPa Result There is no spurious emission with levels of more than 20 dB below the applicable limit RF Technologies Ltd. Page 20 of 37 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 3 June, 2011 Report No.: RY1106Z03R1 Model: BU-2 2.7.2 Between 30 – 1000 MHz Test equipment used (refer to List of utilized test equipment) BA04 CL11 PR08 TR06 Tested Date: 1 June, 2011 Temperature: 21 ˚C Humidity: 45 % Atmos. Press: 1019 hPa Operating mode: Continuous Communication (GFSK, 2480MHz: Worst configuration) EUT position: Z-plane (Maximum position) Measurement distance: 3 m Frequency Reading Factor Loss Result Limit Margin Antenna No. Gain [dB] [MHz] [dBuV] [dB/m] [dB] [dBuV/m] [dBuV/m] [dB] Polarization 1 76.507 58.9 6.9 7.6 49.8 23.6 40.0 16.4 Hori. 2 76.527 59.8 6.9 7.6 49.8 24.5 40.0 15.5 Vert. 3 1000.000 36.3 21.7 13.6 49.7 21.9 53.9 32.0 Hori. 4 1000.000 36.3 21.7 13.6 49.7 21.9 53.9 32.0 Vert. Calculation method The Correction Factors and RESULT are calculated as followings. Correction Factor [dB/m] = FACTOR [dB/m] + LOSS [dB] – GAIN [dB] RESULT [dBuV/m] =READING [dBuV] + Correction Factor [dB/m] Sample calculation at 76.527 MHz vertical result as follow: Result [dBuV/m] = Reading + C.F = 59.8 + 6.9 + 7.6 - 49.8 = 24.5 Margin = Limit – Result = 40.0 – 24.5 = 15.5 [dB] RF Technologies Ltd. Page 21 of 37 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 3 June, 2011 Report No.: RY1106Z03R1 Model: BU-2 Graphical express of test result (30MHz-1000MHz) Antenna polarization: Horizontal Antenna polarization: Vertical RF Technologies Ltd. Page 22 of 37 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 3 June, 2011 Report No.: RY1106Z03R1 Model: BU-2 2.7.3 Above 1000 MHz Test equipment used (refer to List of utilized test equipment) PR12 SH01 TR06 CL23 CL24 AT33 HPF1 DH01 AC01 CL28 Tested Date: 26 April, 2011 Temperature: 20 ˚C Humidity: 38 % Atmos. Press: 1014 hPa Restricted Band Edge (Worst Configuration) Low channel (π/4DQPSK, X-plane, Horizontal) * RBW 1 MHz Marker 1 [T1 ] * RBW 1 MHz Marker 1 [T1 ] * VBW 1 MHz 51.99 dBµV * VBW 10 Hz 38.27 dBµV Ref 110 dBµV * Att 0 dB SWT 2.5 ms 2.380564103 GHz Ref 110 dBµV * Att 0 dB SWT 23 s 2.369358974 GHz 110 110 PEAK AVERAGE A A 100 100 1 PK 1 PK VIEW VIEW 90 90 TDF TDF 80 80 D1 73.9 dBµV 70 70 60 60 1 D1 53.9 dBµV 3DB 3DB AC 50 AC 50 1 40 40 30 30 20 20 F1 F1 10 10 Start 2.31 GHz 9.2 MHz/ Stop 2.402 GHz Start 2.31 GHz 9.2 MHz/ Stop 2.402 GHz High channel (8DPSK, X-plane, Horizontal) * RBW 1 MHz Marker 1 [T1 ] * RBW 1 MHz Marker 1 [T1 ] * VBW 1 MHz 53.93 dBµV * VBW 10 Hz 43.78 dBµV Ref 110 dBµV * Att 0 dB SWT 2.5 ms 2.483500000 GHz Ref 110 dBµV * Att 0 dB SWT 5 s 2.483500000 GHz 110 110 100 PEAK A 100 AVERAGE A 1 PK 1 PK VIEW VIEW 90 90 TDF TDF 80 80 D1 73.9 dBµV 70 70 60 60 1 3DB D1 53.9 dBµV 3DB AC 50 AC 50 1 40 40 30 30 20 20 F1 F1 10 10 Start 2.48 GHz 2 MHz/ Stop 2.5 GHz Start 2.48 GHz 2 MHz/ Stop 2.5 GHz RF Technologies Ltd. Page 23 of 37 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 3 June, 2011 Report No.: RY1106Z03R1 Model: BU-2 Harmonics and Spurious Emission above 1000 MHz Tested Date: 18 May, 2011 Temperature: 22 ˚C Humidity: 53 % Atmos. Press: 1016 hPa Operating mode: Continuous Communication (GFSK, 2480MHz: Worst Configuration) EUT position: Y-plane (Maximum position) Measurement distance: 3 m There are no spurious emissions other than listed below; Reading Result Limit Margin Frequency C.F. No. Peak Ave Peak Ave Peak Ave Peak Ave Polarization [MHz] [dB] [dBuV] [dBuV] [dBuV] [dBuV] [dBuV] [dBuV] [dB] [dB] 1 4960.000 54.3 46.0 3.0 57.3 49.0 73.9 53.9 16.6 4.9 Hori. 2 4960.000 48.4 40.1 3.0 51.4 43.1 73.9 53.9 22.5 10.8 Vert. RF Technologies Ltd. Page 24 of 37 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 3 June, 2011 Report No.: RY1106Z03R1 Model: BU-2 2.8 Transmitter AC power line conducted emissions Test setup Test setup was implemented according to the method of ANSI C63.4: 2003 clause 6 “General requirements for EUT equipment arrangements and operation” and Annex H.1 “AC power line conducted emission measurements setup”. Test procedure Measurement procedures were implemented according to the method of ANSI C63.4: 2003 clauses 7, clause 13.1.3 and Annex H.2 “AC power line conducted emission measurements”. Exploratory measurements were used the spectrum analyzer to identify the frequency of the emission that has the highest amplitude relative to the limit by operating the EUT in a range of typical modes of operation, cable positions, and with a typical system equipment configuration and arrangement. Final ac power line conducted emission measurements were performed based on the exploratory tests. The EUT cable configuration and arrangement and mode of operation that produced the emission with the highest amplitude relative to the limit are selected for the final measurement. When the measurement value is greater than average limitation the average detection measurements were performed. Applicable rule and limitation §15.207 (a) AC power line conducted limits Conducted Limit (dBuV) Frequency of Emission (MHz) Quasi-peak Average 0.15-0.5 66 to 56 * 56 to 46 * 0.5-5 56 46 5-30 60 50 * Decreases with the logarithm of the frequency. The lower limit applies at the band edges. Test equipment used (refer to List of utilized test equipment) TR04 LN06 CL18 Test results - Complied with requirement. RF Technologies Ltd. Page 25 of 37 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 3 June, 2011 Report No.: RY1106Z03R1 Model: BU-2 Test Data Tested Date: 1 June, 2011 Temperature: 21 ˚C Humidity: 45 % Atmos. Press: 1019 hPa Operating mode: Continuous Communication (GFSK, 2480MHz: Worst configuration) Reading Result Limit Margin Frequency C.F. No. QP AV QP AV QP AV QP AV PHASE [MHz] [dB] [dBuV] [dBuV] [dBuV] [dBuV] [dBuV] [dBuV] [dB] [dB] 1 0.151 29.6 7.1 10.2 39.8 17.3 65.9 55.9 26.1 38.6 Va 2 0.153 30.6 6.9 10.2 40.8 17.1 65.8 55.8 25.0 38.7 Vb 3 0.159 26.3 5.2 10.2 36.5 15.4 65.5 55.5 29.0 40.1 Vb 4 0.164 28.3 5.6 10.2 38.5 15.8 65.3 55.3 26.8 39.5 Vb 5 0.165 28.3 5.7 10.2 38.5 15.9 65.2 55.2 26.7 39.3 Va 6 0.175 25.8 4.5 10.2 36.0 14.7 64.7 54.7 28.7 40.0 Va The power line conducted emission voltage is calculated by adding the LISN factor and Cable loss attenuation from the measured reading. The calculation is as follows: Result = Reading + C. F where C.F = LISN Factor + Cable Loss [dB] Sample calculation at 0.153 MHz QP result as follow: Result [dBuV] = Reading + C.F = 30.6 + 10.2 = 40.8 [dBuV] Margin = Limit – Result = 65.8 – 40.8 = 25.0 [dB] RF Technologies Ltd. Page 26 of 37 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 3 June, 2011 Report No.: RY1106Z03R1 Model: BU-2 Graphical express of test result (0.15 MHz-30MHz) AC Power line conducted emission. (Phase Va) AC Power line conducted emission. (Phase Vb) RF Technologies Ltd. Page 27 of 37 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 3 June, 2011 Report No.: RY1106Z03R1 Model: BU-2 2.9 Receiver Radiated spurious emissions Test setup - Same as clause 2.7 Test procedure - Same as clause 2.7 Applicable rule and limitation at 3m §15.109 radiated emission limitation Frequency Measurement Distance Field Strength Field Strength (MHz) (m) (uV/m) (dBuV/m) 30 – 88 3 100 40.0 88 –216 3 150 43.5 216 – 960 3 200 46.0 Above 960 3 500 53.9 In the emission table above, the tighter limit applies at the band edges. The emission limits shown in the above table are based on measurements employing a CISPR quasi-peak detector. Test results - Complied with requirement. 2.9.1 Between 30 – 1000 MHz Test equipment used (refer to List of utilized test equipment) BA04 CL11 PR08 TR06 Test Data Tested Date: 1 June, 2011 Temperature: 21 ˚C Humidity: 45 % Atmos. Press: 1019 hPa Operating mode: Continuous Receiving (2480MHz) EUT position: Z-plane (Maximum position) Measurement distance: 3 m Frequency Reading Factor Loss Result Limit Margin Antenna No. Gain [dB] Polarization [MHz] [dBuV] [dB/m] [dB] [dBuV/m] [dBuV/m] [dB] 1 76.505 54.8 6.9 7.6 49.8 19.5 40.0 20.5 Hori. 2 76.526 55.3 6.9 7.6 49.8 20.0 40.0 20.0 Vert. 3 1000.000 36.2 21.7 13.6 49.7 21.8 53.9 32.1 Hori. 4 1000.000 36.2 21.7 13.6 49.7 21.8 53.9 32.1 Vert. Calculation method The Correction Factors and RESULT are calculated as followings. Correction Factor [dB] = FACTOR [dB/m] + LOSS [dB] – GAIN [dB] RESULT [dBuV/m] =READING [dBuV] + Correction Factor [dB] Sample calculation at 76.526 MHz vertical result as follow: Result [dBuV/m] = Reading + C.F = 55.3 + 6.9 + 7.6 - 49.8 = 20.0 Margin = Limit – Result = 40.0 – 20.0 = 20.0 [dBuV/m] RF Technologies Ltd. Page 28 of 37 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 3 June, 2011 Report No.: RY1106Z03R1 Model: BU-2 Graphical express of test result (30MHz-1000MHz) Antenna polarization: Horizontal Antenna polarization: Vertical RF Technologies Ltd. Page 29 of 37 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 3 June, 2011 Report No.: RY1106Z03R1 Model: BU-2 2.9.2 Above 1000 MHz Test equipment used (refer to List of utilized test equipment) PR12 TR06 CL23 CL24 DH01 Tested Date: 20 May, 2011 Temperature: 23 ˚C Humidity: 53 % Atmos. Press: 1016 hPa Operating mode: Continuous Receiving (2441MHz: Worst configuration) EUT position: Y-plane (Maximum position) Measurement distance: 3 m There are no spurious emissions other than listed below; Reading Result Limit Margin Frequency C.F. No. Peak Ave Peak Ave Peak Ave Peak Ave Polarization [MHz] [dB] [dBuV] [dBuV] [dBuV] [dBuV] [dBuV] [dBuV] [dB] [dB] 1 2167.076 48.7 37.2 -5.5 43.2 31.7 73.9 53.9 30.7 22.2 Vert. 2 12205.000 40.2 26.2 11.3 51.5 37.5 73.9 53.9 22.4 16.4 Hori. 3 12205.000 39.3 26.2 11.3 50.6 37.5 73.9 53.9 23.3 16.4 Vert. Note: No. 2, 3 is noise floor. Calculation method The RESULT is calculated as followings. RESULT [dBuV/m] = READING [dBuV] + Antenna Factor [dB/m] + Cable Loss [dB] – AMP Gain [dB] RF Technologies Ltd. Page 30 of 37 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 3 June, 2011 Report No.: RY1106Z03R1 Model: BU-2 2.10 Receiver AC power line conducted emissions Test setup - Same as clause 2.8 Test procedure - Same as clause 2.8 Applicable rule and limitation §15.107 (a) AC power line conducted limits Conducted Limit (dBuV) Frequency of Emission (MHz) Quasi-peak Average 0.15-0.5 66 to 56 * 56 to 46 * 0.5-5 56 46 5-30 60 50 * Decreases with the logarithm of the frequency. The lower limit applies at the band edges. Test equipment used (refer to List of utilized test equipment) TR04 LN06 CL11 Test results - Complied with requirement. RF Technologies Ltd. Page 31 of 37 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 3 June, 2011 Report No.: RY1106Z03R1 Model: BU-2 Test Data Tested Date: 1 June, 2011 Temperature: 21 ˚C Humidity: 45 % Atmos. Press: 1019 hPa Operating mode: Continuous Receiving (2480MHz: Worst configuration) Reading Result Limit Margin Frequency QP AV C.F. QP AV QP AV QP AV No. PHASE [MHz] [dBuV] [dBuV] [dB] [dBuV] [dBuV] [dBuV] [dBuV] [dBuV] [dBuV] 1 0.151 30.4 7.1 10.2 40.6 17.3 65.9 55.9 25.3 38.6 Vb 2 0.151 30.4 7.3 10.2 40.6 17.5 65.9 55.9 25.3 38.4 Va 3 0.158 26.8 5.6 10.2 37.0 15.8 65.6 55.6 28.6 39.8 Va 4 0.159 26.5 5.3 10.2 36.7 15.5 65.5 55.5 28.8 40.0 Vb 5 0.171 24.1 3.8 10.2 34.3 14.0 64.9 54.9 30.6 40.9 Vb 6 0.180 24.7 5.5 10.2 34.9 15.7 64.5 54.5 29.6 38.8 Va The power line conducted emission voltage is calculated by adding the LISN factor and Cable loss attenuation from the measured reading. The calculation is as follows: Result = Reading + C. F where C.F = LISN Factor + Cable Loss [dB] Sample calculation at 0.151MHz QP result as follow: Result [dBuV] = Reading + C.F = 30.4 + 10.2 = 40.6 [dBuV] Margin = Limit – Result = 65.9 – 40.6 = 25.3 [dBuV] RF Technologies Ltd. Page 32 of 37 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 3 June, 2011 Report No.: RY1106Z03R1 Model: BU-2 Graphical express of test result (0.15 MHz-30MHz) AC Power line conducted emission. (Phase Va) AC Power line conducted emission. (Phase Vb) RF Technologies Ltd. Page 33 of 37 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp

RFT Issue Date: 3 June, 2011 Report No.: RY1106Z03R1 Model: BU-2 4 List of utilized test equipment/ calibration RFT Kind of Equipment Calibration Calibrated Manufacturer Model No. Serial Number ID No. and Precision Date until Anechoic Chamber (1st AC01(EM) test room) JSE 203397C - 2011/04/23 2012/04/30 Anechoic Chamber (1st AC01(EG) test room) JSE 203397C - 2010/11/13 2011/11/30 AT33 Attenuator 10dB 26GHz INMET 26A-10 FT2075 2010/07/14 2011/07/31 BA04 Bilogical Antenna SCHAFFNER CA2855 2903 2011/01/26 2012/01/31 CL11 Antenna Cable for RE RFT - - 2010/10/19 2011/10/31 CL18 Antenna Cable for CE RFT - - 2011/05/13 2012/05/31 CL22 RF Cable 2.0m SUHNER SUCOFLEX104 274755 2011/03/10 2012/03/31 CL23 RF Cable 0.5m SUCOFLEX SF104PE 48773/4PE 2010/06/15 2011/06/30 CL24 RF Cable 5.0m SUCOFLEX SF104PE 48775/4PE 2010/06/15 2011/06/30 CL28 RF Cable 1.0m SUHNER SUCOFLEX104PE 75769 2010/08/04 2011/08/31 DH01 DRG Horn Antenna A.H. Systems SAS-571 785 2010/01/20 2012/01/31 High Pass Filter HPF1 (3500MHz) TOKIMEC TF323DCA 603 2010/06/15 2011/06/30 LN06 LISN Kyoritsu KNW-407F 8-1773-3 2011/05/17 2012/05/31 PR08 Pre. Amplifier Sonoma Instrument 315 263504 2011/01/12 2012/01/31 Agilent PR12 Pre. Amplifier (1-26G) Technologies 8449B 3008A02513 2011/01/18 2012/01/31 Spectrum Analyzer SA06 (F/W: 3.60 SP1) Rohde & Schwarz FSP40 100071 2010/11/15 2011/11/30 Standard Horn Antenna SH01 (18-26G) A.H. Systems SAS-572 208 2008/07/23 2011/07/22 Test Receiver TR04 (F/W : 4.32) Rohde & Schwarz ESCI 100447 2010/09/21 2011/09/30 Test Receiver TR06 (F/W : 3.93 SP2) Rohde & Schwarz ESU26 100002 2010/09/02 2011/09/30 The measuring equipment, which was utilized in performing the tests documented herein, has been calibrated in accordance with the manufacturer's recommendations for utilizing calibration equipment, which is traceable to recognized national standards. RF Technologies Ltd. Page 37 of 37 472, Nippa-cho, Kohoku-ku, Yokohama, 223-0057, Japan Telephone: +81+(0)45- 534-0645, FAX: +81+(0)45- 534-0646, Web: http://www.rft.jp


Document Created: 2011-06-06 14:46:46
Document Modified: 2011-06-06 14:46:46
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC