User Manual

FCC ID: K4ER400BQ

Users Manual

Download: PDF
FCCID_4158914

ENFORCER® SD—R400—BQ Microwave RTE Sensor Manual Features: e 12~24 VDC Operating voltage Universally compatible, install the sensor e —24,150GHz Microwave Doppler technology above automatic doors for no—touch e 10ft (3m) Sensing range, adjustable ingress/egress * Adjustable relay output time, 1~33 s More consistent detection in large areas e Small size allows for a wide range and over a wide range of temperatures of applications Indoor use only SECO—LARM®_SL]T @

ENFORCER Microwave RTE Sensor Introduction: The ENFORCER Microwave RTE Sensor is a compact motion sensor with an adjustable output timer that can be connected to an access control keypad, gate opener, and can be used to trigger any device with an egress input. Parts List: 1x Microwave sensor 2x Mounting screws 1x Mounting template 1x 5—Pin connector cable 1x Manual Specifications: Operating voltage 12~24 VDC Current Standby 23mA@12VDC / 14mA@24VDC draw Active 39mA@12VDC / 21mA@24VDC Sensor frequency 24.150GHz Sensor range 3‘~10‘ (0.9~3m), adjustable Sensor Vertical 0°~90° angle Horizontal +30° Detection Front/back 20°~30° angle Left/right 60°~70° Min. detection speed bemi/s Output relay 2A@30VDC (0.5A@125VAC) Dry relay, NO/NC/COM Relay output time 1~33 s Mounting height 6‘~10‘ (1.8~3 m) Cable length 8 (2.5m) LED Indicator Red on relay activation Case material Black ABS and polycarbonate Operating temperature ~4°~131° F (—20°~55° C) Dimensions 31/8"x23/s"x21/s" (80x60x54 mm) Weight 2.5—0z (70g) Overview: Front Side Front 3%/"(BOmm) ——>»I 4 2/s" (GAmm) (cover removed) LED Indicator n ENFORCER® 2518" {6Omm) werl Microwave Connector emitter pad cable hole SECO—LARM U.S.A., Inc.

ENFORCER Microwave RTE Sensor Installation: 1. Find a suitable mounting location no more than 10ft (3m) high. 2. Apply the mounting template to the wall where the sensoris to be mounted. 3. Mark the locations for the screws, and drill one hole to the right of where it says "Insert connector here." 4. Remove the cover as described in How to Remove the Cover Before Installation, see below. NOTE: Make sure not to touch the microwave emitter pad once the coveris removed 5. Connect the 5—pin connector cable to the microwave sensor and feed the opposite end through the connector hole in the wall and complete wiring as necessary. See pg. 4 for Wiring Diagram. 6. Secure the microwave sensor to the wall with both screws. 7. Adjust the sensor‘s vertical angle and rotation as necessary. NOTE: Grip the sensor above and below the emitter pad. Do not pinch the sides as it may damage the trimpots. 8. Adjust the sensor‘s range and relay‘s output time using the two trimpots, see Adjusting the Sensor Range and Relay Output Time on pg. 4, and replace the cover. How to Remove the Cover Before Installation: 1. Squeeze the sides of the cover and wedge a thin flat—head screwdriver into the gap between the cover and the sensor base. 2. Apply moderate upward pressure to pry the cover off and away from the sensor base. NOTE: Take care to inset the screwdriver into the gap between the cover and sensor base, and not into the recessed area of the base just below. How to Remove the Cover Once Installed: 1. Insert a screwdriver into the hole at the top of the sensor cover. 2. Apply moderate downward pressure to pry the cover off and away from the sensor base. Side view Detection Area: Horizontal Area of Detection: 1. The horizontal area of detection will change depending on the horizontal tilt angle of the sensor. 2. Mounted 7ft (2.1m) tall at center 0°, the area of detection is 5ft (1.5m) wide and 2 is 1 00 i 152 5ft (1.5m) deep. Units: meter (m) Vertical Area of Detection: 1. The vertical area of detection will change depending on the verticaltilt angle of the = sensor. 0 2. Mounted 7ft (2.1m) tall at center 0° with a 45° vertical tilt, the area of detection extends 0°~90° to 6ft (1.8m). SECO—LARM U.S.A., Inc. 3

ENFORCER Microwave RTE Sensor Wiring Diagram: Ralay output Brown wire: +12~24 VDC Black wire: (—) Ground time trimpot “’@ Yellow wire: N.C. Sensor range 3 Green wire: COM trimpot ——>I\ White wire: N.O. Adjusting the Sensor Range and Relay Output Time: 1. To adjust the sensor‘s range, turn the trimpot countarclockwise Olilput time Segsor renge To (decrease) or clookwise (increase). Min: 3ft (0.9m) / Max: 10ft (3m) $ 2. To adjust the relayoutput time, tum the trimpot counterclockwise ® : + Distance (d_eerease) or clockwise (increase}. ¢ t ¥ y Min: 1 second / Max: 33 seconds Min. Max. Min. Max. > Troubleshooting: . * Sensor poweris off. LED is off «_ Check wiring and plug into power supply. * Make sure door is in automatic mode. Dooris not reacting normally _ Check the output configuration of the sensor. Typical wiring for the sensor‘s output is N.O. * Sensor is disturbed when the doorcloses due to motion and vibrations. The door opens and closes on its own * Make sure the sensor is properly secured. * Adjust microwave emitter pad angle. * Reduce detection area size. Door opens for no reason * Adjust the angle and range of sensor. IMPORTANT: Users and installers of this product are responsible for ensuring that the installation and configuration of this product complies with all national, state, and local laws and codes related to locking and egress devices. SECO—LARM will not beheld responsible for the use of this product in violation of any current laws or codes. FCC COMPLIANCE STATEMENT FCC ID: K4ER4OOBQ THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment. IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user‘s authority to operate the device. WARRANTY: This SECO—LARM product is warranted against defects in material and workmanship while used in normal service for one (1) year from the date of sale to the original customer. SECO—LARM‘s obligation is limited to the repair or replacement of anydefective part if the unit is retuned, fransportation prepaid, to SECO—LARM. This Warranty is void if damage is caused by or aftibuted to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO—LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO—LARM and the purchaser‘s exclusive remedy, shall be limited to the replacementor repair only, at SECO—LARM‘s option. In no event shall SECO—LARM be liable for any special, collateral, incidental, or consequential personal or property damage of any kind to the purchaser or anyone else. NOTICE: The SECO—LARM policy is one of confinual development and improvement. For that reason, SECO—LARM reserves the right to change specifications without nofice. SECO—LARM is also not responsible for misprints. All trademarks are the property of SECO—LARM U.S.A., Inc. or their respective owners. Copyright© 2018 SECO—LARM U.S.A., Inc. All rights reserved. SECO—LARM® U.S.A., Inc. e 16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco—larm.com z* Picant Phone: (949) 261—2999 | (800) 662—0800 Email: sales@seco—larm.com ML§0—2400—80.181120.docx SECO—LARM U.S.A., Inc. PS


Document Created: 2019-02-01 15:06:16
Document Modified: 2019-02-01 15:06:16
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC