User Manual

FCC ID: K4E919TB4H

Users Manual

Download: PDF
FCCID_396578

Typical Applications: Positive Output: 12VDC receiver power driving a 12¥DC appliance: COM |— Positive Power Source COM NC NC NO |—— Positive Power Output NO 12VDC O/P _ — GND T } Power for SK—910R2 7 4 12VDC} Power for SK—910R2 Negative Output: COM |— Negative Power Source NC 12¥DC receiver power input, 24VAC output driving a motor COM |—— 24VAC(1) Input NC 24VAC(2) ENFORLER NO |— Negative Power Output NO 24VAC(1) Output — ~— } Power for SK—910R2 ~— ~J —I _ +200 — GND SK—910R2 RECEIVER with General Specifications Operating Frequency: 315 MHz SK—919TB4H—N TRANSMITTER Memory Capacity: 15 transmitter button codes per channel Operating Voltage: 11VDC ~ 24VDC or 11VAC ~ 24VAC Operating Current: 8 mA @ 12VDC (standby) 3OmA/channel @ 12VDC (activated) Relay Contact Rating: Form ‘C‘ type; 10¥A @ 24VDC or 120VAC per channel Connectors: Screw Terminals, +, —, with N/O, N/C, and COM per channel Dimensions: 3.25" x 2.7" x 1.1" (83 x 68 x 27.5 mm) MODEL: SK—919TB4H—N FCC 1D : K4E919TB4H THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOY CAUSE HARMEFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, |INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATIONL IMPORTANT NOTES: ‘ a) The changes or rodifications not expressly approved by the pon‘i; responsible for compliance could void the user‘s authority to operate the equipment. b) To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user‘s authority to operate the device. The SECO—LARM policy is one of continual development and improvement. For this reason, SECO—LARM reserves the right to change specifications without further notice. Ay4M SECO—LARM® U.S.A., INC. Telephone Fax 16842 Millikan Avenue (800) 662—0800 (949) 261 —7326 Irvine, CA 92606 (949) 261 —2999 FILE: TE—10, C:\DTPIMANUAL\MUKS10RIv2.R65 OCT2001 SECO—LARM® ORDER PART# 931

MODE SWITCH #1 System | I—— MODE SWITCH #2 The SK—910R2 RF receiver are compatible with both code hopping and fixed—code transmitters. They can be used 0 LP3 O Antenna Program Loop for a variety of applications, such as allowing the same transmitter to arm/disarm a vehicle alarm and open/close a (see Extended Range Antennas below) garage door opener. The SK—910R2 receiver has two—channel outputs. Each channel can learn the codes of up to (see Below) 15 different transmitter buttons on a first—in, first—out basis. Installation Notes \_\ Three—Pin Antenna Port (see Extended Range Antennas below) 1. Mount out of sight in a location where it is not surrounded by metal, and where it is not exposed to the weather or moisture. Metal will block the RF signal, resulting in a reduced range. Output Program Loops 2. For best range, pull the antenna wire as long and straight as possible. If the receiver receives interference from local RF activity (e.g.., airport or military base), the antenna wire can be folded. DO NOT CUT THE Output type LP1 LP2 ANTENNA WIRE. 4—second momentary Uncut — Uncut a. & 1—second momentary Uncut Cut Learning a New SK—919TB4H—N Button Code — — Toggle Cut Uncut 1. To learn a transmitter code for channel 1, press mode switch #1 for three seconds. The green LED will start Latch Cut Cut to flash quickly. 2. While the green LED is flashing quickly, press any desired button on the compatible SK—919TB4H—N transmitter. The green LED wilt flash once and then turn off to show that that button was learned. 3. Repeat steps 1 and 2 to learn more buttons into channel 1. CH 2 DRY RELAY COM NOTE — The green LED will flash a maximum of 15 seconds. If no transmitter button is pressed dunng this time, CH 2 DRY RELAY NC the receiver will exit the code—learning mode, and the green LED will twyn off. CH 2 DRY RELAY NO 4. To learn a new SK—919TB4H—N transmitter button for channel 2, the procedure is the same as for channel 1, CH 1 DRY RELAY COM except mode switch #2 initiates the code—learning process, and the red LED shows status. CH 1 DRY RELAY NC CH 1 DRY RELAY NO Note Regarding Code Learning GND 1. The receiver will only learn the code of a particular button once. Once a button‘s code is learned, if you try to +11—24VDC code—learn that button again, whetherit is for the same channel or not, the receiver will exit code learning mode. CH 2 STATUS LED 2. Each channel can learn the codes of a maximum of 15 transmitter buttons. If you attempt to learn a sixteenth _ CH 1 STATUS LED button, the earliest code learned will be deleted. 3. To clear all codes — Press the appropriate mode switch (#1 or #2) for three seconds. When the LED starts Mode Switch Operation (one per channel) flashing, press that switch again for three seconds. The LED flashes twice to indicate that all codes associated * Learn mode — Press and hold the switch for three seconds. with that channel are now deleted. . * Clear memory — Press three seconds, then when the LED starts flashing, press again for three seconds to Programming Relay Output Modes delete all previously learned codes. The relay output(s) can be programmed for one of four different modes, depending on the application: * Reset latched output — If this channel was programmed for latch output, once the relay is turned on with a * 4—second momentary —— Press the transmitter button once. The relay turns on for 4 seconds, and then turns off. transmitter button, press the mode switch to turn the retay off. (This is the DEFAULT mqde) * Memory Display — Press and release the mode switch to show number of codes stored. LED will flash a number * 1—second momentary — Press the transmitter button once. The relay turns on for 1 second, and then turns off. of times to correspond to the number of codes stored. * Toggle—— Press the transmitter button ohce and the relay turnson. Press a compatible transmitter button again, LED indication (one per channel) and the relay turns off. * Steady on — Senses signal from a transmitter button whose code was already learned. * Latch — Press the trangmitter button once, and the relay turns on and stays on. The relay will remain on until the * Fast flash — In the code—learning mode. appropriate mode switch (#1 or #2) is pressed to reset, regardless of whether a compatible transmitter button * One flash — A transmitter button code was learned. is pressed again or not. * Two flashes — All previouslty learned To program outputs, open case and find the 2 jumpers marked LP1 and LP2. Cut these jumpers, if needed, as follows: transmitter button codes were deleted. Output type LPI LP2 A—second momentary Uncut Uncut SK—919TB4HK—N Four—Button, 15—Channel Transmitter 1—second momentary Uncut Cut Over 68 billion (6.8 x 10") possible codes. Toggle Cut Uncut LED transmission indicator. Includes visor clip and 3VDC lithium battery (2 pos.). Latch Cut Cut Slim—line design. NOTE — The output mode of both relays is the same. In other words, you cannot have 4—second momentary Size: 3‘A" x 23/s" x ‘A", (88 x 55 x 12 mm). output for channel 1 and latch output for channel 2.


Document Created: 2004-02-06 14:14:14
Document Modified: 2004-02-06 14:14:14
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC