Test Report

FCC ID: K4E3133PPQ

Test Report

Download: PDF
FCCID_4063807

Report No.: ATE20181750 Page 1 of 21 APPLICATION CERTIFICATION FCC Part 15C On Behalf of Superior Electronics Corporation Heavy-Duty Outdoor Access Control Keypad with Proximity Reader Model No.: SK-3133-PPQ FCC ID: K4E3133PPQ Prepared for : Superior Electronics Corporation Address : No. 10 Lane 31, Chongde St., Sinyi District, Taipei City, Taiwan 110 Prepared by : Shenzhen Accurate Technology Co., Ltd. Address : 1/F., Building A, Changyuan New Material Port, Science & Industry Park, Nanshan District, Shenzhen, Guangdong, P.R. China Tel: +86-755-26503290 Fax: +86-755-26503396 Report No. : ATE20181750 Date of Test : October 9-October 11, 2018 Date of Report : October 12, 2018 FCC ID: K4E3133PPQ Shenzhen Accurate Technology Co., Ltd

Report No.: ATE20181750 Page 2 of 21 TABLE OF CONTENTS Description Page Test Report Declaration 1. TEST RESULTS SUMMARY ......................................................................................................... 4 2. GENERAL INFORMATION .......................................................................................................... 5 2.1. Description of Device (EUT)....................................................................................................................5 2.2. Special Accessory and Auxiliary Equipment ...........................................................................................5 2.3. Description of Test Facility ......................................................................................................................6 2.4. Measurement Uncertainty.........................................................................................................................6 3. MEASURING DEVICE AND TEST EQUIPMENT ..................................................................... 7 3.1. The Equipment Used to Measure Conducted Disturbance .......................................................................7 3.2. The Equipment Used to Measure Radiated Emission...............................................................................7 4. POWER LINE CONDUCTED MEASUREMENT ....................................................................... 8 4.1. Block Diagram of Test Setup....................................................................................................................8 4.2. Power Line Conducted Emission Measurement Limits............................................................................8 4.3. Configuration of EUT on Measurement ...................................................................................................8 4.4. Operating Condition of EUT ....................................................................................................................8 4.5. Test Procedure ..........................................................................................................................................9 4.6. Data Sample..............................................................................................................................................9 4.7. Power Line Conducted Emission Measurement Results ..........................................................................9 5. RADIATED EMISSION MEASUREMENT................................................................................ 14 5.1. Block Diagram of Test............................................................................................................................14 5.2. Radiated Emission Limit ........................................................................................................................15 5.3. EUT Configuration on Measurement .....................................................................................................15 5.4. Operating Condition of EUT ..................................................................................................................15 5.5. Test Procedure ........................................................................................................................................16 5.6. Data Sample............................................................................................................................................17 5.7. Radiated Emission Measurement Result ................................................................................................17 6. ANTENNA REQUIREMENT........................................................................................................ 21 6.1. The Requirement ....................................................................................................................................21 6.2. Antenna Construction .............................................................................................................................21 FCC ID: K4E3133PPQ Shenzhen Accurate Technology Co., Ltd

Report No.: ATE20181750 Page 3 of 21 Test Report Declaration Applicant : Superior Electronics Corporation Address : No. 10 Lane 31, Chongde St., Sinyi District, Taipei City, Taiwan 110 Manufacturer : Superior Electronics Corporation Address : No. 10 Lane 31, Chongde St., Sinyi District, Taipei City, Taiwan 110 Product : Heavy-Duty Outdoor Access Control Keypad with Proximity Reader Model No. : SK-3133-PPQ Measurement Procedure Used: FCC CFR47 Part 15 Subpart C Section 15.207 and 15.209 ANSI C63.10: 2013 The device described above is tested by Shenzhen Accurate Technology Co., Ltd. to determine the maximum emission levels emanating from the device. The maximum emission levels are compared to the FCC Part 15 Subpart C limits both radiated and conducted emissions. The measurement results are contained in this test report and Shenzhen Accurate Technology Co., Ltd. is assumed full responsibility for the accuracy and completeness of these measurements. Also, this report shows that the Equipment Under Test (EUT) is to be technically compliant with the FCC requirements. This report applies to above tested sample only. This report shall not be reproduced in part without written approval of Shenzhen Accurate Technology Co., Ltd. Date of Test : October 9-October 11, 2018 Date of Report : October 12, 2018 Prepared by : (Star Yang, Engineer) Approved & Authorized Signer : (Sean Liu, Manager) FCC ID: K4E3133PPQ Shenzhen Accurate Technology Co., Ltd

Report No.: ATE20181750 Page 4 of 21 1. TEST RESULTS SUMMARY Test Items Test Standard Test Results Power Line Conducted Emission FCC Part 15.207 Pass Radiated Emission FCC Part 15.209 Pass FCC ID: K4E3133PPQ Shenzhen Accurate Technology Co., Ltd

Report No.: ATE20181750 Page 5 of 21 2. GENERAL INFORMATION 2.1.Description of Device (EUT) M/N : SK-3133-PPQ Operation Frequency : 125kHz Modulation Type : GFSK Antenna Gain : 0dBi Type of Antenna : Coil Antenna Rating : 12-24V AC/DC 2.2.Special Accessory and Auxiliary Equipment N/A FCC ID: K4E3133PPQ Shenzhen Accurate Technology Co., Ltd

Report No.: ATE20181750 Page 6 of 21 2.3.Description of Test Facility EMC Lab : Recognition of accreditation by Federal Communications Commission (FCC) The Designation Number is CN1189 The Registration Number is 708358 Listed by Innovation, Science and Economic Development Canada (ISEDC) The Registration Number is 5077A-2 Accredited by China National Accreditation Service for Conformity Assessment (CNAS) The Registration Number is CNAS L3193 Accredited by American Association for Laboratory Accreditation (A2LA) The Certificate Number is 4297.01 Name of Firm : Shenzhen Accurate Technology Co., Ltd Site Location : 1/F., Building A, Changyuan New Material Port, Science & Industry Park, Nanshan District, Shenzhen, Guangdong, P.R. China 2.4.Measurement Uncertainty Conducted emission expanded uncertainty : U=2.23dB, k=2 Radiated emission expanded uncertainty : U=3.08dB, k=2 (9kHz-30MHz) Radiated emission expanded uncertainty : U=4.42dB, k=2 (30MHz-1000MHz) Radiated emission expanded uncertainty : U=4.06dB, k=2 (Above 1GHz) FCC ID: K4E3133PPQ Shenzhen Accurate Technology Co., Ltd

Report No.: ATE20181750 Page 7 of 21 3. MEASURING DEVICE AND TEST EQUIPMENT 3.1. The Equipment Used to Measure Conducted Disturbance Item Equipment Manufacturer Model No. Serial No. Last Cal. Cal. Interval 1. Test Receiver Rohde & Schwarz ESCS30 100307 Jan.06, 2018 1 Year 2. L.I.S.N. Schwarzbeck NLSK8126 8126431 Jan.06, 2018 1 Year 3. Pulse Limiter Rohde & Schwarz ESH3-Z2 100305 Jan.06, 2018 1 Year 50Ω Coaxial Anritsu Corp MP59B 6200283936 Jan.06, 2018 1 Year 4. Switch 5. RF Coaxial Cable SUHNER N-2m No.2 Jan.06, 2018 1 Year 6. Measurement Software: ES-K1 V1.71 3.2. The Equipment Used to Measure Radiated Emission Item Equipment Manufacturer Model No. Serial No. Last Cal. Cal. Interval 1. Spectrum Analyzer Rohde&Schwarz FSV40 101495 Jan.06, 2018 1 Year 2. Test Receiver Rohde& Schwarz ESR 101817 Jan.06, 2018 1 Year 3. Bilog Antenna Schwarzbeck VULB9163 9163-323 Jan.06, 2018 1 Year 4. Loop Antenna Schwarzbeck FMZB1516 1516131 Jan.06, 2018 1 Year 5. RF Switching Compliance RSU-M2 38322 Jan.06, 2018 1 Year Unit+PreAMP Direction 6. Pre-Amplifier Agilent 8447D 294A10619 Jan.06, 2018 1 Year 7. Pre-Amplifier Rohde&Schwarz CBLU11835 3791 Jan.06, 2018 1 Year 40-01 8. 50 Coaxial Switch Anritsu Corp MP59B 6200506474 Jan.06, 2018 1 Year 9. RF Coaxial Cable RESENBERGER N-12m No.11 Jan.06, 2018 1 Year 10. RF Coaxial Cable RESENBERGER N-0.5m No.12 Jan.06, 2018 1 Year 11. RF Coaxial Cable SUHNER N-2m No.13 Jan.06, 2018 1 Year 12. RF Coaxial Cable SUHNER N-0.5m No.15 Jan.06, 2018 1 Year 13. RF Coaxial Cable SUHNER N-2m No.16 Jan.06, 2018 1 Year 14. RF Coaxial Cable RESENBERGER N-6m No.17 Jan.06, 2018 1 Year 15. Measurement Software: EZ_EMC V1.1.4.2 FCC ID: K4E3133PPQ Shenzhen Accurate Technology Co., Ltd

Report No.: ATE20181750 Page 8 of 21 4. POWER LINE CONDUCTED MEASUREMENT 4.1.Block Diagram of Test Setup Test Receiver AC Mains L.I.S.N EUT 4.2.Power Line Conducted Emission Measurement Limits Frequency Limit dB(V) (MHz) Quasi-peak Level Average Level 0.15 - 0.50 66.0 – 56.0 * 56.0 – 46.0 * 0.50 - 5.00 56.0 46.0 5.00 - 30.00 60.0 50.0 NOTE1: The lower limit shall apply at the transition frequencies. NOTE2: The limit decreases linearly with the logarithm of the frequency in the range 0.15MHz to 0.50MHz. 4.3.Configuration of EUT on Measurement The following equipments are installed on Power Line Conducted Emission Measurement to meet the commission requirement and operating regulations in a manner, which tends to maximize its emission characteristics in a normal application. 4.3.1.Heavy-Duty Outdoor Access Control Keypad with Proximity Reader (EUT) Model Number : SK-3133-PPQ Manufacturer : Superior Electronics Corporation 4.4.Operating Condition of EUT 4.4.1. Setup the EUT and simulator as shown as Section 4.1. 4.4.2. Turn on the power of all equipment. 4.4.3. Let the EUT work in test mode and measure it. FCC ID: K4E3133PPQ Shenzhen Accurate Technology Co., Ltd

Report No.: ATE20181750 Page 9 of 21 4.5.Test Procedure The EUT is put on the plane 0.8 m high above the ground by insulating support and is connected to the power mains through a line impedance stabilization network (L.I.S.N.). This provides a 50ohm coupling impedance for the EUT system. Please refer the block diagram of the test setup and photographs. Both sides of AC lines are checked to find out the maximum conducted emission. In order to find the maximum emission levels, the relative positions of equipment and all of the interface cables shall be changed according to ANSI C63.10: 2013 on Conducted Emission Measurement. The bandwidth of test receiver (R & S ESCS30) is set at 9kHz. The frequency range from 150kHz to 30MHz is checked. 4.6.Data Sample Frequency Transducer QuasiPeak Average QuasiPeak Average QuasiPeak Average Remark (MHz) value Level Level Limit Limit Margin Margin (Pass/Fail) (dB) (dBV) (dBV) (dBV) (dBV) (dB) (dB) X.XX 10.6 25.3 17.0 59.0 49.0 33.7 32.0 Pass Transducer value = Insertion loss of LISN + Cable Loss Result = Quasi-peak Level/Average Level + Transducer value Limit = Limit stated in standard Calculation Formula: Margin = Limit – Reading level value – Transducer value 4.7.Power Line Conducted Emission Measurement Results PASS. The frequency range from 150kHz to 30MHz is checked. Emissions attenuated more than 20 dB below the permissible value are not reported. The spectral diagrams are attached as below. FCC ID: K4E3133PPQ Shenzhen Accurate Technology Co., Ltd

Report No.: ATE20181750 Page 10 of 21 FCC ID: K4E3133PPQ Shenzhen Accurate Technology Co., Ltd

ACCURATE TECHNOLOGY CO.,LTD CONDUCTED EMISSION STANDARD FCC PART 15C EUT: Eeavy—Duty Outdoor Access Control Keypad with Proximity Reader Manufacturer: SUPERRIOR ELECTRONICS CORPORATION Operating Condition: ON Test Site: 2#Shielding Room Operator: Frank Test Specification: L 24V/608z Comment : Report NO.:ATE20181750 M/N: SK—3133—PPQ Start of Test 2018—10—9 / 9150145 SCAN TABLE: "V 150K—30MHz fin" Short Description: _SUB_STD_VTERM2 1.70 Start Stop Step Detsctor Meas. IF Transducer Frequency Frequency Width Time Bandw. 150.0 kEz 30.0 MHz 4.5 kHz QuasiPeak 1.0 s 9 kBz NSLK8126 2008 Average Level [dBuV] Frequency [Hz] x x xmBs B—1750 —2_Ein +o+ + ues B—1750—2fin? ues r—1750 ~2pre mes B—1750—2pre2 uzx ce is # ¥ or voltage oP umm roo is 2 v ay Voltage 27 MEASUREMENT RESULT: "F—1750—2_fin" 2018—10—9 9: 52 Frequency Level Transd Limit Margin Detector Line PE MBz dBpV dB dBpV dB 0. 361500 19. 40 10.9 59 39.3 QP LL GND 0. 748500 23.10 11.1 56 32.3 QP LL GND 1,464000 23.10 11.2 56 32.9 P LL GND 2.130000 19.20 11.3 56 36.8 P LL GND 5.338500 9.40 11.5 60 50.6 P LL GND 24.004500 20 .00 11.7 60 40.0 P LL GND MEASUREMENT RESULT: "F—1750—2_fin2" 2018—10—9 9: 52 Frequency Level Transd Limit Margin Detector Line PE MBz dBpv dB dapv dn 0. 253500 17.00 10.9 52 34.6 AV LL GND 0.775500 21.10 11.1 46 24.9 AV LL GND 1,000500 21.00 11.1 46 25.0 AV LL GND 2.143500 13. 40 11.3 46 32.6 AV L1 GND 5.271000 4.20 11.4 50 45.8 av LL GND 24,004500 19. 60 11.7 50 30.4 AV LL GND

Report No.: ATE20181750 Page 12 of 21 FCC ID: K4E3133PPQ Shenzhen Accurate Technology Co., Ltd

ACCURATE TECHNOLOGY CO., LTD CONDUCTED EMISSION STANDARD FCC PART 15C EUT: Eeavy—Duty Outdoor Access Control Keypad with Proximity Reader Manufacturer: SUPERRIOR ELECTRONICS CORPORATION Operating Condition: ON Test Site: 2#Shielding Room Operator: Frank Test Specification: N 12v/6082z Comment: Report NO.:ATE20181750 M/N: SK—3133—PPQ Start of Test: 2018—10—9 / 9:55:54 SCAN TABLE: "V 150K—30MHz fin" Short Description: _SUB_STD_VTERM2 1 Start Stop Step Detector Meas. IF Transducer Frequency Frequency Width Time Bandw. 150.0 kiz 30.0 MEz 4.5 kiz Quasipeak 1.0 s 9 kRz NSLK8126 2008 Average Level [dBpV 300k 400k 600k 800k 1M am 3 4M 5M 6M BM 10M 20M 30M Frequency [H2] MEASUREMENT RESULT: "F—1750—4_fin" 2018—10—9 9 188 Frequency Tevel Transd Limit Margin Detector Line PE MBz dBuy dB dsuy dB 325500 19. 60 10.9 60 .0 oP N GND 501000 23.80 11.0 56 2 QP N GND 1. 252500 24 .40 11.2 56 .6 P N GND 2.184000 18.50 11.3 56 150 9P N GND 5.271000 9.40 11.4 60 .6 QP N GND 004500 20 .90 11.3 60 1 P N GND MEASUREMENT RESULT: "FP—1750—4_ fin2" 2018—10—9 9 158 Frequency Level Transd Limit Margin Detector Line PE MBz dBuy dB dBpy as 249000 10.9 52 33.4 AV N GNp 501000 11.0 46 25.8 AV N GNp . 000500 11.1 46 25.9 AV N GNp S oo to 1+ «134500 1158 46 32.5 AV N GND 031500 11.5 50 44.8 AV N GND . 004500 11.7 50 29.1 Av N cup to

Report No.: ATE20181750 Page 14 of 21 5. RADIATED EMISSION MEASUREMENT 5.1.Block Diagram of Test 5.1.1.Block diagram of connection between the EUT and simulators AC Mains EUT 5.1.2.Block diagram of test setup (In chamber) FCC ID: K4E3133PPQ Shenzhen Accurate Technology Co., Ltd

Report No.: ATE20181750 Page 15 of 21 5.2.Radiated Emission Limit Limit: 2400/125=19.2uV/m@300m Distance Correction Factor=40log (test distance/specific distance) 5.3.EUT Configuration on Measurement The following equipments are installed on Radiated Emission Measurement to meet the commission requirements and operating regulations in a manner which tends to maximize its emission characteristics in normal application. 5.3.1.Heavy-Duty Outdoor Access Control Keypad with Proximity Reader (EUT) Model Number : SK-3133-PPQ Manufacturer : Superior Electronics Corporation 5.4.Operating Condition of EUT 5.4.1. Setup the EUT and simulator as shown as Section 5.1. 5.4.2. Turn on the power of all equipment. 5.4.3. Let the EUT work in test mode and measure it. FCC ID: K4E3133PPQ Shenzhen Accurate Technology Co., Ltd

Report No.: ATE20181750 Page 16 of 21 5.5.Test Procedure The EUT and its simulators are placed on a turntable, which is 0.8 meter high above ground. The turntable can rotate 360 degrees to determine the position of the maximum emission level. EUT is set 3.0 meters away from the receiving antenna, which is mounted on an antenna tower. The antenna can be moved up and down between 1.0 meter and 4 meters to find out the maximum emission level. Broadband antenna (calibrated bilog antenna) is used as receiving antenna. Both horizontal and vertical polarizations of the antenna are set on measurement. In order to find the maximum emission levels, all of the interface cables must be manipulated according to ANSI C63.10: 2013 on radiated emission measurement. From 9kHz to 30MHz at distance 3m The EUT was rotated a full revolution in order to obtain the maximum value of the electric field intensity. From 30MHz to 1000MHz at distance 3m The measuring antenna height varied between 1 and 4m and EUT was rotated a full revolution in order to obtain the maximum value of the electric field intensity. The measurements were performed for both vertical and horizontal antenna polarization. The final measurement will be performed with an EMI Receiver set to Quasi Peak detector for the frequency bands 9kHz to 90kHz and 110 to 490 kHz where an average detector will be used according to Section 15.209(d)(2). The final level, expressed in dBuV/m, is arrived at by taking the reading from the EMI receiver(Level dBuV) and adding the antenna correction factor and cable loss factor(Factor dB) to it. This result then has to be compared with the relevant FCC limit. The resolution bandwidth during the measurement is as follows: 9kHz – 150kHz: ResBW: 200Hz 150kHz – 30MHz: ResBW: 9kHz The bandwidth of the EMI test receiver (R&S ESCS30) is set at 120kHz from 30MHz to 1000MHz. FCC ID: K4E3133PPQ Shenzhen Accurate Technology Co., Ltd

Report No.: ATE20181750 Page 17 of 21 5.6.Data Sample Frequency( Reading Factor Result Limit Margin Remark MHz) (dBv) (dB/m) (dBv/m) (dBv/m) (dB) X.XX 49.83 -22.03 27.80 43.50 -15.70 QP Frequency(MHz) = Emission frequency in MHz Reading(dBv) = Uncorrected Analyzer/Receiver reading Factor (dB/m)= Antenna factor + Cable Loss – Amplifier gain Result(dBv/m) = Reading + Factor Limit (dBv/m)= Limit stated in standard Calculation Formula: Margin(dB) = Result (dBv/m)–Limit(dBv/m) Result(dBv/m)= Reading(dBv)+ Factor(dB/m) The “Margin” column of the following data tables indicates the degree of compliance with the applicable limit. For example, a margin of -7dB means the emission is 7dB below the limit. 5.7.Radiated Emission Measurement Result PASS. The EUT has pretest form 12V to 24V AC/DC, the worst case data 24Vac was recorded in the report Emissions attenuated more than 20 dB below the permissible value are not reported. The spectral diagrams are attached as below. FCC ID: K4E3133PPQ Shenzhen Accurate Technology Co., Ltd

Report No.: ATE20181750 Page 18 of 21 From 9kHz to 30MHz：TX Mode Polarization: X Frequency Reading Factor Result Limit @3m Margin Height Degree Detector (MHz) (dBuV/m) (dB) (dBuV/m) (dBV/m) (dB) (cm) (deg.) *0.125 50.20 11.77 61.97 102.32 -40.35 QP 124 176 0.552 40.93 3.54 44.47 72.76 -28.29 QP 150 355 0.920 35.04 0.66 35.67 68.32 -32.65 QP 202 228 1.288 29.43 -0.28 29.15 65.41 -36.26 QP 145 208 18.516 29.76 -4.86 24.90 69.54 -44.64 QP 154 35 29.594 27.60 -7.02 20.58 69.54 -48.96 QP 148 38 Polarization: Y Frequency Reading Factor Result Limit @3m Margin Height Degree Detector (MHz) (dBuV/m) (dB) (dBuV/m) (dBV/m) (dB) (cm) (deg.) *0.125 46.19 11.77 57.96 102.32 -44.36 QP 112 201 0.368 34.28 6.13 40.41 96.29 -55.88 QP 139 138 0.552 34.25 3.54 37.79 72.76 -34.97 QP 120 323 0.920 32.41 0.66 33.07 68.33 -35.26 QP 150 230 1.288 25.71 -0.28 25.43 65.41 -39.98 QP 154 193 18.802 35.22 -4.95 30.27 69.54 -39.27 QP 135 330 Polarization: Z Frequency Reading Factor Result Limit @3m Margin Height Degree Detector (MHz) (dBuV/m) (dB) (dBuV/m) (dBV/m) (dB) (cm) (deg.) *0.125 45.22 11.77 56.99 102.32 -45.33 QP 130 146 0.588 34.49 3.54 38.03 72.21 -34.18 QP 201 301 0.920 30.19 0.66 30.85 68.33 -37.48 QP 156 258 1.288 27.85 -0.28 27.57 65.41 -37.84 QP 200 322 18.147 23.92 -4.86 19.06 69.54 -50.48 QP 236 146 29.361 25.36 -7.02 18.34 69.54 -51.20 QP 145 198 “ * ” : Fundamental frequency Part 15 Section 15.31(f)(2) (9kHz-30MHz) Limit at 3m=Limit@300m-40*log(3(m)/300(m)) Limit at 3m=Limit@30m-40*log(3(m)/30(m)) FCC ID: K4E3133PPQ Shenzhen Accurate Technology Co., Ltd

| mifi! ACCURATE TECHNOLOGY CO., LTD. Site: 1# Chamber F1,Bldg.A, Changyuan New Material Port Keyuan Rd, Tel:+86—0755—26503290 Science & Industry Park, Nanshan Shenzhen,P.R.China Fax:+86—0755—26503396 Job No.: frank2018 #1812 Polarization: Horizontal Standard: FCC Part 150C 3M Radiated Power Source: AC 24V/60Hz Test item: Radiation Test Date: 2018/10/11 Temp.( C)/Hum.(%) 25 C/55% Time: 10:54:13 EUT: Heavy—Duty Outdoor Access Control Keypad with Proximity Reader Mode: TX 125KHz Model: SK—3133—PPQ Manufacturer: SUPERRIOR ELECTRONICS CORPORATION Note: Report NO.:ATE20181750 70.0 dBu¥/m uB —— 60 50 a0 30 BB |relis<>> fersecoefrnnnedenconfrenipersfee« $ 10 0.0 I ‘ . ; 30.000 40 50 60 70 80 300 400 500 600 700 1000.0 MHz Freq. Reading Factor Result Limit |Margin Height Degree No. (MHz) (dBuV/m) (dB) (dBuv/im) (dBuvim)| (aBy P4°C| (em) (deg) Remark 2ro8161| 4765 1711 3054 4600 |—1546) aop 200 52 —A 2882830| arse 1653 3133 4600 |—1467) oP 200 231 N| 295.4623| 48.65 —16.35 32.30 46.00 |—13.70| QP 200 202 mlool 307.1051] 47.60 —16.12 31.48 46.00 |—14.52] QP 200 98 326.0079]| 45.68 —15.55 30.13 46.00 |—15.87| QP 200 102 l 376.5227) 4345 —14.18 29.27 46.00 |—16.73| QP 200 156 o|

| mi! ACCURATE TECHNOLOGY CO., LTD. Site: 1# Chamber F1,Bidg,A,Changyuan New Material Port Keyuan Rd, Tel:+86—0755—26503290 Science & Industry Park,Nanshan Shenzhen,P.R.China Fax:+86—0755—26503396 Job No.: frank2018#1813 Polarization: Vertical Standard: FCC Part 15C 3M Radiated Power Source: AC 24V/60Hz Test item: Radiation Test Date: 2018/10/11 Temp.( C)/Hum.(%) 25 C/55% Time: 10:59:33 EUT: Heavy—Duty Outdoor Access Control Keypad with Proximity Reader Mode: TX 125KHz Model: SK—3133—PPQ Manufacturer: SUPERRIOR ELECTRONICS CORPORATION Note: Report NO.:ATE20181750 70.0 dBu¥/m limit1 : —— t i ; i ; i 50 40 30 s ..b P M Pb ds 10 0o ; } P } 1 30.000 40 50 60 70 80 300 400 500 600 700 1000.0 MHz No: (iarfii') (ggfiijff"n?) F(Z‘é‘)‘” (dgis\;:’:n) (dIE;Lr{]/iltm) Nézrg)in Detector H(sirfl?l fg;g(_;ef Remark 72.7202) 5012 —23.00 27.12 40.00 |—12.88| QP 100 106 —— 119.7672) 58.32 —21.32 37.00 43.50 |—6.50| QP 100 59 NJ 122.7493| 58.16 —21.45 36.71 43.50 |—6.79| QP 100 210 oJ 130.3048] 60.12 —21.74 38.38 43.50 |—5.12|) QP 100 322 ) 154.2427| 56.01 —21.95 34.06 43.50 |—9.44| QP 100 156 l 252.2522| 5312 ~18.05 35.07 46.00 |—10.93] QP 100 13 o|

Report No.: ATE20181750 Page 21 of 21 6. ANTENNA REQUIREMENT 6.1.The Requirement According to Section 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. 6.2.Antenna Construction Device is equipped with permanent attached antenna, which isn’t displaced by other antenna. The max Antenna gain of EUT is 0dBi. Therefore, the equipment complies with the antenna requirement of Section 15.203. Antenna ***** End of Test Report ***** FCC ID: K4E3133PPQ Shenzhen Accurate Technology Co., Ltd


Document Created: 2018-11-07 10:13:21
Document Modified: 2018-11-07 10:13:21
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC